IMPRESSA X7-S

Instructions for use

Art. Nr. 66309 8/06 UL/NSF

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/ or injury to persons, including the following: Read all instructions. Do not touch hot surfaces. Use handles or knobs. To protect against fire, electric shock and personal injury do not immerse cord, plugs, or appliance in water or other liquid. Close supervision is necessary when any appliance is used by or near children. Unplug from outlet any when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury. Do not use outdoors. Do not let cord hang over edge of table or counter, or touch hot surfaces. Do not place on or near a hot gas or electric burner, or in a heated oven. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control off, then remove plug from wall outlet. Do not use appliance for other than intended use. Use extreme caution when disposing steam. For household and commercial use.

SAVE THESE INSTUCTIONS

SPECIAL CORD SET INSTRUCTIONS
Regarding your Cord set. A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If a long detachable power-supply cord or extension cord is used, (1) the marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance, (2) if the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord, and (3) the longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over. WARNING: To reduce the risk of fire or electric shock, do not remove any service covers. No user serviceable parts inside. Repair should be done by authorized personnel only.

CAUTION:

This appliance is for household and commercial use. Any servicing other than cleaning and user maintenance should be performed by an authorized service representative. Do not immerse base in water or try to disassemble. To reduce the risk of fire or electric shock, do not remove the base. No user serviceable parts inside. Repair should be done by authorized service personnel only. Check voltage to be sure that the voltage indicated on the name plate agrees with your voltage. Never use warm or hot water to fill the water container! Use cold water only! Keep your hands and the cord away from hot parts of the appliance during operation. Never clean with scouring powders or hard implements.

Legend:

DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important
JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.com

A I Fig. 1

B II Fig. 2 Fig. 3 Fig. 4 III IV 2 III

3 Fig. 5 Fig. 6

1 Fig. 7 Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 14

Fig. 15

Fig. 13

Fig. 16

Fig. 17

Fig. 18

Fig. 19

Fig. 20

Fig. 21

Fig. 22

Fig. 23

Fig. 24

Fig. 25

Fig. 26

Fig. 27

Fig. 28

Fig. 29

Fig. 30

Fig. 31

Fig. 32

Fig. 33

Fig. 34

P R O G.

D F G K
Operating elements JURA IMPRESSA X7-S
1. Drip tray 2. Drip tray cover 3. Ground container 4. Heigt-adjustable coffee and cappuccino spout 5. Draw-off button 2 coffees 6. Draw-off button 2 Espressos 7. Draw-off button 1 coffee 8. Draw-off button 1 Espresso 9. Draw-off button Cappuccino 10. Selector key for grinder 11. Display dialogue system 12. Grinders 13. Funnel for cleaning tablets 14. Water tank 15. Cover for programming keys 16. Draw-off button steam 17. Draw-off button hot water 18. Pivoting nozzle for hot water/steam 19. Accessory drawer
Programming keys/Coffee key

A B C D E F G H I J

ON/OFF switch Draw-off button pot Draw-off button milk froth Rinsing key Draw-off button hot water Cleaning button Descaling button Draw-off buttom steam Open program Forward-setting of criteria/changing of memory indications up-wards K Close program L Back-setting of criteria/changing of memory indications downwards

Table of contents

1. Description....page 2. Safety instructions....page 2.1 Warnings....page 2.2 Safety precautions....page 3. Preparing the machine....page 3.1 Checking the mains voltage....page 3.2 Checking the fuse....page 3.3 Filling the water tank....page 3.4 Adding coffee beans....page 4. Switching the machine on....page 5. Rinsing the machine....page 6. Selecting the grinder....page 6.1 Setting the grinder....page 7. Adjusting the grinder....page 8. Adjusting of water hardness.....page 9. Installing the filter cartridge....page 9.1 Installing the filter....page 9.2 Replacing the filter....page 10. Coffee....page 10.1 Drawing off coffee/espresso....page 10.2 Drawing off Cappuccino....page 10.3 Drawing off pots of coffee....page 11. Drawing off hot water.....page 12. Drawing off steam.....page 13. Drawing-off milk froth....page 14. Switching the machine off....page 15. Programming.....page 15.1 Programming grinding amount....page 15.2 Programming temperature....page 15.3 Programming amount of water....page 15.4 Programming amount of milk....page 15.5 Programming portion of hot water....page 15.6 Programming water hardness....page 15.7 Programming clock....page 15.8 Programming machine on....page 15.9 Programming machine off....page 15.10 Draw-offs....page 15.11 Programming language....page 16. Care and maintenance.....page 16.1 Fill water....page 16.2 Cleaning the water tank....page 16.3 Installation of an automatic filling device....page 16.4 Empty grounds container.....page 16.5 Empty drip tray....page 16.6 Grounds container missing....page 16.7 Drip tray missing....page 16.8 Fill beans....page 16.9 Removing foreign objects....page 16.10 Clean machine....page 16.11 Machine scaled.....page 16.12 Clean contacts....page 16.13 General cleaning instructions...page 16.14 Cleaning the coffee outlet....page 17. Cappuccino cleaning....page 18. Combined cleaning....page 19. Coffee cleaning....page 20. Descaling.....page 21. Disposal.....page 22. Adjustments by the JURA service technician....page 23. Tips for perfect coffee.....page 24. Messages.....page 25. Problems.....page 26. Legal information.....page 27. Technical specifications.....page
Important information for the user
Thank you for choosing this JURA product. Please study these instructions carefully before using your new machine and keep them in a safe place for easy reference in the future. Should you require further information or should particular problems occur that are not dealt with in sufficient detail for you in these operating instructions, then please ask your local dealer for the information you require or get in touch with us directly. You will also find useful tips on operation and maintenance of your IMPRESSA X7-S on the website at www.jura.com. Dont forget to check out the Knowledge Builder our animated operating instructions. LEO, our assistant, will take you through all the functions.

3. Preparing the machine 3.1 Checking the mains voltage
The machine has been set to the correct mains voltage in the factory. Ensure that your mains voltage corresponds to the details on the rating plate attached to the reverse of your machine (Fig. 1/A).

3.2 Checking the fuse

Check whether the fuse matches your machine.
3.3 Filling the water tank
Remove the water tank and rinse it out well with cold tap water. Then fill the water tank and put it back into the machine. Please ensure that the tank locks in properly. Please only use fresh, cold water. Never fill up with milk, mineral water and other fluids. You can also top up water without removing the tank. Simply remove the cover and pour in the water from above with a vessel and replace the lid again.

1. Description

The first IMPRESSA for the office and small gastronomy area is outstanding not only because of its modern technology, but also a number of features, and prepares 1 or 2 cups of espresso/coffee in only one brewing process. The Intelligent Pre Brew Aroma System (I.P.B.A.S.) ensures that the full coffee aroma is made use of and supplies the best espresso/coffee, guaranteed to be covered by a splendid froth. Optionally, coffee can be used from either of the grinders, and the mixture can be programmed individually. Drawing-off Cappuccino is possible at the push of a button and without moving the cups. Integrated rinsing, cleaning and de-scaling programmes ensure perfect cleanliness at the push of a button.

3.4 Adding coffee beans

To ensure that your machine gives satisfaction for a long time and to avoid repairs, please note that the grinder on your JURA coffee machine is not suitable for coffee beans that have been treated with additives (e.g. sugar) during or after roasting. Use of such coffee blends can result in damage to the grinder. Any repair costs incurred as a result are not covered by the warranty provisions. You have the possibility of adding two different sorts of coffee beans. Remove the cover from the bean container. Clean out any dirt or foreign objects from the bean container. Fill coffee beans into the bean container and replace the cover again.
2. Safety instructions 2.1 Warnings
Children are unaware of the dangers that can be caused by electrical machines; for this reason, children should never be left unsupervised with electrical machines. The machine may only be used by people who have been instructed. Never use a faulty machine or one with a damaged power cable. Never repair or open the machine yourself. Repairs may only be done by authorised service centres using original spare parts and accessories. Never immerse the machine in water.
4. Switching the machine on
Operate the switch on the reverse of the machine (Fig. 1/II). Switch the machine on with the ON/OFF operating switch. : PLEASE WAIT Place an empty cup under the coffee spout (4). : RINSE UNIT The rinsing is done first via the Cappuccino nozzle, after which the coffee spout is cleaned.

2.2 Safety precautions

Never expose the machine to the effects of weather (rain, snow, frost) and never operate it with your hands wet. Place the IMPRESSA on a firm, level base that is resistant to any water that may leak. Never stand on hot or warm surfaces (oven hobs). Keep out of the reach of children. Remove the plug from the power socket if you are away for some time (holidays etc.). Always remove the plug from the power socket before cleaning. When removing the plug from the power socket, never tug on the cord or the machine itself. The machine is connected to the mains power socket via an electric cable. Please ensure that no-one trips over the cable and pulls the machine down. Keep children and pets at a distance. Never put the machine or parts of it into the dishwasher. To prevent overheating, please put the machine in a place with a good circulation of air. If you use de-scaling agents containing acid, remove any splashes and drips on sensitive surfaces, in particular natural stone and wood surfaces, straight away or take corresponding safety precautions.

5. Rinsing the machine

A rinsing process is automatically started when the machine is switched off. However, if no Cappuccino has been drawn off, the rinsing is only done via the coffee spout when switching off. When the machine has been switched off and has cooled down, the rinsing process is requested when it is switched on again.

6. Selecting the grinder

You can select the grinder manually Press the key 1x or 2x. The light above the key tells you which grinder has been activated (grinder left or grinder right).

6.1 Setting the grinder

So that the coffee can be matched to the grinder as well as possible, carry out the following steps: Press the key Draw off 6 coffee and 6 espresso by manually selecting the grinder left and then the grinder right. We recommend that you also readjust the grinder after: a change of sort of coffee beans extreme changes of the degree of grinding service
9. Installing the filter cartridge
If the filter cartridge is installed properly you dont have to de-scale your machine anymore. For more information on the filter cartridge refer to the brochure CLARIS plus. Hard on limescale. Gentle on your coffee machine.
9.1 Installing the filter
First installation of a filter cartridge must be carried out by a service engineer. Contact your service partner.

7. Adjusting the grinder

You have the opportunity of adapting the grinder to the roast of your coffee. We recommend the following: for a light roast a finer adjustment for a dark roast a coarser adjustment To adjust the grinding, turn the setting rings into the required position (Fig. 2) You have the following options: the smaller the dots, the finer the grinding the larger the dots, the coarser the grinding The grinding may only be adjusted with the grinder in operation.

9.2 Replacing the filter

After drawing off 50 liters the filter cartridge will be used up. Please monitor the period of use of the filter cartridge (max. 2 months) using the scale on the cartridge holder by the water tank. : REPLACE WATER FILTER
8. Adjustment of water hardness
Water is heated in the machine. This leads to scale as a result of use, which is automatically shown on the display. The machine must be adjusted to match the hardness of the water used. For this, please use the enclosed test stick. 1 water hardness on the German scale corresponds to 1.79 on the French scale. The machine has 5 hardness settings to choose from. The indications on the display mean: WATER HARDNESS LEVEL Water hardness function switched off WATER HARDNESS German water hardness LEVEL 1 French water hardness 1.79 12.53 WATER HARDNESS German water hardness LEVEL 2 French water hardness 14.32 26.85 WATER HARDNESS German water hardness LEVEL 3 French water hardness 28.64 41.14 WATER HARDNESS German water hardness LEVEL 4 French water hardness 42.96 53.7 In the factory, the machine is set to hardness level 3. You can alter this setting. Proceed as follows: Switch the machine on with the ON/OFF operating switch. : PLEASE WAIT Press the key PROG. (I) until an acoustic signal is heard. : AJUST COFFEE QUANTITY / SELECT PRODUCT Press the key + until the following report appears: : WATER HARDNESS LEVEL 3 Press the key PROG., an acoustic signal is heard and the level set flashes. By pressing the key - or + you can set the required level. To store, press the key PROG. An acoustic signal is heard. Press the key EXIT (K).
1. Switch off your IMPRESSA X7-S. 2. Press the following key combination (Fig. 11). NB: Press the keys at the same time. : OK 3. Empty the water tank and install the filter cartridge together with the cartridge holder in the water tank, applying a gentle pressure downward. Move back the cartridge holder until it engages audibly (Fig. 12). 4. Fill the water tank with cold, fresh tap water and reinstall it. 5. After replacing the filter draw off 0.5 liters of water. The water may be slightly coloured (not harmful)
10. Coffee 10.1 Drawing off coffee / espresso
: SELECT PRODUCT Place 1 or 2 cups, as necessary, under the coffee spout (4) and press the required selection switch. The pre-brew system (I.P.B.A.S) moisturises the coffee powder, briefly interrupts the discharge and then starts the actual brewing procedure. You can interrupt the draw-off prematurely by pressing any of the coffee draw-off buttons. In order to obtain outstanding froth, you can adapt the coffee spout (4) individually to match the size of your cups.

10.2 Drawing off cappuccino
: SELECT PRODUCT Put milk/Tetra Pak into a jug and immerse the cappuccino tube into the milk. Place 1 cup under the coffee spout and press the draw-off key. The machine firstly prepares the milk froth, then the coffee (Fig. 3). You can interrupt the milk froth and the coffee prematurely by pressing the draw-off key once more. 10 min. after the draw-off of Cappuccino, a rinsing is automatically started. The rinsing is announced in advance by an acoustic signal.
10.3 Drawing off pots of coffee
: SELECT PRODUCT Place 1 pot under the coffee spout (4) and press the draw-off key. Your pot of coffee is brewed in a number of cycles. The number of cycles is shown in the display. You can interrupt the draw-off prematurely at any time by pressing the draw-off key again.

Draw-offs Language

15.1 Programming grinding amount
Switch your machine on the with ON/OFF operating switch. Press the key PROG. until an acoustic signal is heard. : ADJUST COFFEE QUANTITY / SELECT PRODUCT Press the required draw-off key. : (selected product) .II. + By pressing the key + or - you can determine the amount to be ground. To store, press the key PROG. : (selected product) : 100% : 0% You can determine the allocation of the grinder left or right. By pressing the key + or - you can change the values. To store, press the key PROG. : ADJUST COFFEE QUANTITY / SELECT PRODUCT Press the required draw-off key, the key + in order to reach the next phase or the key EXIT to quit the programming.
11. Drawing off hot water
: SELECT PRODUCT Place a cup under the pivoting nozzle (18) and press the drawoff key. : PORTION HOT WATER The draw-off of the programme portion of hot water stops automatically. You can interrupt the draw-off prematurely at any time by pressing the draw-off key again. When water is drawn off, there can be splattering at the beginning. The pivoting nozzle becomes hot. Avoid direct contact with the skin.

12. Drawing off steam

: SELECT PRODUCT Place a cup with the liquid to be heated under the pivoting nozzle (18) and press the draw-off key. : STEAM ACTIVE To end the draw-off of steam, press the key. When steam is drawn off, there can be splattering at the beginning. The pivoting nozzle becomes hot. Avoid direct contact with the skin.
15.2 Programming Temperature
: ADJUST TEMPERATURE / SELECT PRODUCT Press the required draw-off key. : (selected product) STAND. TEMP. Select the required temperature with the keys + or - (high or standart) To store, press the key PROG. : ADJUST TEMPERATURE / SELECT PRODUCT Press the required draw-off key, the key + in order to reach the next phase or the key EXIT to quit the programming.

16. Care and maintenance 16.1 Fill water
: FILL WATER TANK When this display lights up, no more drawing-off is possible. Fill with water as described under Section 3.3. The water tank should be rinsed out every day and filled with fresh water. If you use an automatic filling device, we recommend that you rinse the water tank out regularly and fill it up with fresh water.

15.7 Programming CLOCK

Programming the clock is necessary if the function Machine on is used. : TIME. : Press the key PROG. By pressing the keys + or - you can set the hours. To store, press the key PROG. By pressing the keys + or - you can set the minutes. To store, press the key PROG. Press the key + in order to reach the next phase or the key EXIT to quit the programming.
16.2 Cleaning the water tank
The water tank should be rinsed and filled with fresh water daily. To clean the water tank, remove it from the machine. a) Cleaning the float shaft Remove the flexible float shaft cover (Fig. 14). Remove the float switch (Fig. 15). Clean the float shaft using the brush (Fig. 16). When installing the float, make sure the position of the guide at the float which runs in the shaft opening is correct (Fig. 17). b) Cleaning the water tank handle Put the water tank handle in vertical position. Press the water tank handle downwards (Fig. 18) Remove the water tank handle from the support. Clean the support using the brush (Fig. 19). After the cleaning, insert the water tank handle in the support again. Pull upwards to engage the handle in the support (Fig 20). c) Cleaning the valve Press upwards the valve body (Fig. 21). Remove the O-ring on the inside of the water tank from the valve body. Remove the valve body together with the spring (Fig. 22/23). Clean the valve body opening using the brush (Fig. 24). d) Valve assembly After cleaning, install the valve body again in reverse order. Do not use any sharp objects to remove the O-Ring.
15.8 Programming machine on
Programming the clock is necessary if the function Machine on is used. : UNIT ON : Press the key PROG. By pressing the keys + or - you can set the hours. To store, press the key PROG. By pressing the keys + or - you can set the minutes. To store, press the key PROG. Press the key + in order to reach the next phase or the key EXIT to quit the programming. The display : means that the function is switched off.

15.9 Programming machine off
: UNIT OFF 5.0 HRS. Press the key PROG. By pressing the keys + or - you can set the hours (switched off or 0.5 hrs. 9 hrs.). To store, press the key PROG. Press the key + in order to reach the next phase or the key EXIT to quit the programming.
16.3 Installation of an automatic filling device
Please read the operating instructions of the automatic filling device.

16.11 Machine scaled

: DECALCIFYING NECESSARY The machine recognises the necessity of de-scaling. You can continue to draw off coffee or hot water/steam. We recommend that you carry out the de-scaling (Chapter 20) within the next few days.
16.4 Empty grounds container
The grounds container collects the coffee grounds. : EMPTY DRAWER When this display lights up, no more draw-offs are possible and the grounds container must be emptied. Carefully remove the drip tray there is water in it. Then remove the grounds container (Fig. 4).

16.12 Clean contacts

: EMPTY DRIP TRAY / CLEAN CONTACTS The de-scaling residue in the area of the contacts must be removed. Please proceed as follows: Rinse the contact fasteners in trough (B) (Fig. 8) as well as the contacts (A) with hot water and washing-up liquid. Then additionally clean the contact fasteners in trough (B) with a brush.

16.5 Empty drip tray

: EMPTY DRIP TRAY When this display lights up, no more draw-offs are possible and the drip tray must be emptied. Carefully remove the drip tray there is water in it (Fig. 4).
16.13 General cleaning instructions
Never use abrasive articles or corrosive chemicals to clean your machine. Wipe off the inside and outside of the casing with a soft, damp cloth. Clean the pivoting nozzle after every use. After heating milk, draw off a little hot water, in order to clean the pivoting nozzle from the inside. The water tank must be rinsed and filled with fresh water every day. If you see any visible scaling in the water tank, you can remove it with a customary de-scaling agent. Remove the water tank in order to clean it.
16.6 Grounds container missing
: DRAWER MISSING When this display lights up, the grounds container has not been inserted properly or is missing.

16.7 Drip tray missing

: DRIP TRAY MISSING When this display lights up, the drip tray has not been inserted properly.

16.8 Fill beans

: FILL COFFEE BEANS Fill with beans as described in Chapter 3.4. The display FILL COFFEE BEANS goes off after a draw-off of coffee. We recommend that you clean the bean container out with a dry cloth from time to time before filling. For this, switch the machine off.
16.14 Cleaning the coffee outlet
We recommend to disassemble and clean the dual spout if you make milk products regularly. a) Removing the coffee outlet Switch off the machine by pressing the ON/OFF key disconnect the machine from power supply. and
16.9 Removing foreign objects
Switch your machine off with the ON/OFF operating switch. Remove the plug from the power socket. Open the hinged door on the reverse of the machine (Fig. 5). Press the slides downwards (Fig. 6) and remove the bean container. Remove any beans with a vacuum cleaner. Position the spanner (Fig. 7). Turn the spanner in an anti-clockwise direction until the foreign object becomes loose. Remove remaining powder with a vacuum cleaner. Now replace the bean container and pull the slides to the front before closing the door (Fig. 6).
Remove the coffee outlet cover (Fig. 25). Open the lid of the coffee distributor (Fig. 26). Pull out the coffee distributor towards the front and press the milk frothing device out of the support from below (Fig. 27/28). Remove the steam supply and milk supply hose from the milk frothing device (Fig. 29/30). Remove the metal adapter of the milk suction hose (Fig. 31). Open the milk supply door on the left side of the machine. Remove the unlocking device of the support of the outlet head (Fig. 32). Pull off the support of the outlet head (to the front) (Fig. 33). Remove the coffee supply hose from the coupling piece (Fig. 34). b) Cleaning the milk frothing device Dismantle the milk frothing device. Clean the parts in hot water and using the corresponding brushes. c) Cleaning the milk frothing hose Separate the milk suction hose in the middle. Clean the milk suction hose and the connecting element using the brush. d) Cleaning the coffee distributor Clean the coffee distributor and the coffee outlet pipe in hot water.

16.10 Clean machine

: CLEANING NECESSARY After 220 draw-offs or 180 rinsings, the machine has to be cleaned. You can continue to draw off coffee and hot water/steam. We recommend that you clean the machine (Chapter 19) within the next few days. Carry out a cleaning (Chapter 19).

e) Coffee outlet assembly Assemble the coffee outlet as described above in reverse order. Use the corresponding brushes for carrying out the cleaning steps described in Sections b) through e).

19. Coffee cleaning

Once the cleaning sequence has started, it must not be interrupted. It takes about 15 min. Switch the machine on with the ON/OFF switch. Press the key until an acoustic signal is heard. : SELECT CLEANING + Press the key + 3x. : COFFEE CLEANING Press the key : EMPTY DRAWER / INSERT TABLET (Fig. 10) / PRESS CLEANING Place a sufficiently large vessel under the coffee spout (4). Press the key. : COFFEE CLEANING/ PLEASE WAIT : EMPTY DRAWER

17. Cappuccino cleaning

Carry out this cleaning every day. Once the cleaning sequence has started, it must not be interrupted. It takes about 5 min. Switch the machine on with the ON/OFF switch. Press the key until an acoustic signal is heard. : SELECT CLEANING + Press the key +. : CAPPUCCINO CLEANING Press the key again. : CLEANER FOR CAPPUCCINO / PRESS CLEANING Place a vessel of at least 0.5 l under the coffee spout (4). Put about 25 cl of water into a vessel and add the cleaner. You can see the amount of cleaner on the label or the sheet accompanying the product in question. Immerse the Cappuccino tube into it. Press the key. : CAPPUCCINO CLEANING / PLEASE WAIT An acoustic signal is heard. : WATER FOR CAPPUCCINO / PRESS CLEAN Fill a vessel with fresh water and immerse the Cappuccino tube into it. Press the key. : CAPPUCCINO CLEANING / PLEASE WAIT

20. Descaling

The machine has an integrated descaling programme. The process takes about 40 min. Once the descaling process has started, it must not be interrupted If you use descaling agents containing acid, remove any splashes and drips on sensitive surfaces, in particular natural stone and wood surfaces, straight away or take corresponding safety precautions. Switch the machine off with the ON/OFF switch. Press the key until an acoustic signal is heard. : EMPTY DRIP TRAY : INSERT AGENT IN TANK / PRESS DECALCIFYING Dissolve 3 tablets completely in 0.7 litres of water in a vessel and pour the mixture into the empty water tank. Place two sufficiently large vessels under the pivoting nozzle (18) and the coffee spout. Press the key. : UNIT DECALCIFYING / PLEASE WAIT An acoustic signal is heard. : EMPTY DRIP TRAY : FILL WATER TANK Place a vessel under the pivoting nozzle (18) and the coffee spout (4). : PRESS DESCALING : UNIT DECALCIFYING / PLEASE WAIT An acoustic signal is heard : EMPTY DRIP TRAY / CLEAN CONTACTS (Chapter 16.4).

DRIP TRAY MISSING EMPTY DRIP TRAY
The drip tray has not locked in properly The drip tray is full The display does not go off despite the tray being emptied

CLEANING NECESSARY

220 draw-offs or 180 rinsings have been done The display does not go off despite the cleaning

DECALCIFYING NECESSARY

The machine must be de-scaled The display does not go off despite the de-scaling

MALFUNCTION

Various causes

25. Problems

Problems Coffee only drips out when drawing off Cause powder too fine Action adjust grinder to a coarser grinding run one or two rinse programmes. If the results are no better, clean the machine. Coffee flow is stopped after the pre-brew Grinder is very noisy Not enough froth when frothing milk Device cannot be switched on with the ON/OFF switch not enough powder in the system foreign object in the grinder Cappuccino blocked Main switch (Fig. 1/II) not switched on Flat not engaged properly draw off one cup of coffee refer to Chapter 16.8 carry out a Cappuccino cleaning (refer to Chapter 17) switch on close flap
If the messages or problems nevertheless still persist, please get in touch with your dealer or directly with the firm of JURA Elektroapparate AG.

26. Legal information

These operating instructions contain all the information necessary for the correct use, operation and maintenance of your machine. Understanding and complying with the directives contained in these operating instructions are essential for the use of the machine without risk and also for safety during operation and maintenance. These operating instructions cannot cover all imaginable uses of the machine. We would further point out that the contents of these operating instructions in no way constitute a part of or amend any previous or existing contract, agreement or legal relationship. All obligations on the part of JURA Elektroapparate AG result from the sales agreement in question, which also contains the complete details of the valid warranty terms. These contractual warranty terms are neither extended nor limited in any way by the information contained in these operating instructions. These operating instructions contain information protected by copyright. Photocopying or translation into another language without the prior written approval of JURA Elektroapparate AG are not admissible.

27. Technical specifications Version UL 120 V AC
Voltage: Output: Intensity of current: Safety check: Energy consumption standby: Energy consumption ready to make coffee: Pump pressure: Water tank: Capacity, bean container: Capacity, grounds container: Cable length: Weight: Dimensions (BxHxD): 120 V AC 1500 W 12.5 A

Version UL 220 V AC

Voltage: Output: Intensity of current: Safety check: 3 Wh 120 V approx. 60 Wh 220 V approx. 52 Wh 2 x max. 15 bar 5.0 litres 2 x 650 gr max. 40 port. approx. 1.8 m 18.5 kg 43 x 58.5 x 51 cm 220 V AC 2600 W 11.8 A*
* During the preparation of draw-offs of coffee, steam or hot water can also be drawn off.

Dimensions & Specifications
Approvals 9413119 9413149

Model # 9413119

Description JURA Impressa X7 Super Automatic (Black) JURA Impressa X7 Super Automatic (Black) JURA Impressa X7 Super Automatic (Silver)

Volts 120 208-240 120

Total Watts 1500

Amps 10

Cups/ Day 100
Dimensions 20-1/2H x 17W x 20D 20-1/2H x 17W x 20D 20-1/2H x 17W x 20D
Ship Wt 50 lb. 50 lb. 50 lb.

Milk Cooler

Model # 9700041 Holds 1 one gallon milk container 9.0" W x 12.0" H x 13-1/2" D 120V NSF Listed
View of milk jug inside cooler

Accessories:

X7 shown in Black X7 shown in Silver
Milk Frother Cleaner 9700939 Breaks down milk protein buildup. Cleans steam wands and s/s pitchers
Cleaning Tablets 9462535 Cleaning tablets 25 tablets per jar
Decalcifying Tablets 9462688 Prevents lime scale buildup. 30 tablets per jar
Water Connection Kit 9462513 Connects the JURA X7 to water line to fill tank automatically.
7SO Softening Cartridge (Use with Water Connection Kit) 9700111 Reduces hardness in water that can cause mineral build-up in equipment.
BH Filter Cartridge (Use with Water Connection Kit) 9700112 Provides clear, fresh premium quality water for great tasting beverages.
QL3 Filter Head (Use with Water Connection Kit) 9700113 Commercial quality filter head for use with 7SO and BH cartridges. Includes built-in water shut off valve.
Brewmatic 20333 S. Normandie Avenue, Torrance, California 90509 (310) 787-5444 (800) 421-6860 Fax (310) 787-5412 USA E-mail: brew@brewmaticusa.com Intl E-mail: brew_equip@brewmaticusa.com Website: brewmatic.com Brewmatic reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.