iPod/iPhone COMMANDS

Saying iPod will change the current source to iPod from any other source that may be currently selected. Search Artist, Search Playlist, and Search Album 16 are good recommended starting points to begin selecting the music you would like to listen to. The recommended step would be to narrow the search through the alphabetical search function. Search M would list artists, albums, playlists or songs that begin with the letter M depending which category of search was selected. Use the Page Up or Page Down commands until the desired music is displayed on the screen then select the music by Line One, Line Two commands. If an album is listed as a selection along with other albums and you would like to play the entire album then sayPlay One, Play Two, etc. 19
QUICK START GUIDE FOR ADVANCED VOICE CONTROL

DNX9140

Thank you for choosing Kenwoods most advanced multimedia and navigation receiver, the DNX9140. This product allows voice control for both navigation, internal sources and connected sources. This guide will show you some of the more commonly used commands you will be using on a regular basis. For more detailed information on voice commands please refer to the Voice Command Table packaged with this product.

GETTING STARTED

It is important to not only use the correct words for voice control but to speak them clearly at a time when there is minimal background noise. For best results have the microphone facing the driver, operate with vehicle windows and sunroof closed and with only one person (driver) talking while the unit is receiving the commands.

BLUETOOTH COMMANDS

Once your phone has been paired and phonebook information is available on the unit you can access the information by saying Handsfree. 20 The next selection would most likely be Phonebook, Incoming Calls, Outgoing Calls or Missed Calls and Page Up or Page Down commands. When searching through a phonebook use the alphabetical search for best results. Search K would bring up all names that start with K. 21 Make a selection through the Line One, Line Two, etc. commands. Once you have confirmed the correct number has been selected say Call Number to initiate the call. 22
The Push to Talk (PTT) button 1 Pushing the PTT button will enter the user into voice control mode as well as exit out of voice control mode.
TOP RIGHT CORNER VOICE CONTROL ICONS
A Green Icon 2 means ready to receive a voice command and a Red/Brown 3 icon means the unit is not actively listening for a voice command. It is critical that a command is given only when the icon is green even if the confirming text may be seen on the screen before the icon turns green.
TUNER/SATELLITE RADIO COMMANDS
To enter Tuner or Satellite source say either 23 Tuner, Sirius or XM. Seek Up or Seek Down commands can be used to change channels either up or down. Preset One, Preset Two, etc. can be used to select a stored preset. 23 Satellite Radio allows Category List to select the music, talk or sports content to be listened to. Page Up, Page Down and Line One, Line Two, etc. will be used to make selections during this type of operation. 24
After entering the voice control mode for audio sources such as iPod, Tuner, Satellite or DVD/CD small green dots will appear next to the GUI buttons that can be controlled by a voice command. 4
2009 Kenwood USA Corporation. All Rights Reserved. iPod and iPhone are registered trademarks of Apple Computer, Inc. registered in the United States and other countries. The Bluetooth trademarks are owned by SIG, Inc. HD Radio are proprietary trademarks of iBiquity Digital Corp. Sirius and related marks are trademarks of Sirius Satellite Radio, Inc. All other brand, product names, or logos may be trademarks or registered trademarks of their respective holders.

GLOBAL COMMANDS

Global commands can operate regardless of what appears on the screen while other commands remain specific to a source or for operation during navigation. The following is an example of the most commonly used global commands. GLOBAL COMMANDS Where To View Map Find Address Find POI Find POI by Name Find POI by Category Go Home Tuner HD Radio Sirius XM iPod USB Handsfree DVD Control Screen Activates navigation start page Shows your current position on the navigation map Begins the voice command entry process for an address Jumps to selection of Category or Place Name Jumps to Speak the Name of a Popular Place Jumps to POI selection page Routes to address stored as home location Switches source to FM/AM Tuner Switches source to HD Radio if connected Switches source to Sirius if connected Switches source to XM if connected Switches source to iPod Switches source to USB Switches screen to Bluetooth start page Switches source to DVD/CD Changes secondary or minimized source screen to full page view and control

Find POI by Name

A POI can be selected by speaking the name of a popular place such as McDonalds or Home Depot. 9 If there are several choices to choose from then select Line One, Line Two, Page Up, Page Down, etc. or if no selection is correct choose Back 10 and re-enter the commands. Once the POI has been selected the large green Go button 11 appears with the correct POI information on the map. Just say Go and the route will calculate.

NAVIGATION COMMANDS

Find POI by Category
Your Point of Interest (POI) search can be further narrowed by the category you are looking for such as Food, Lodging or Gas. 5 If there are several choices to choose from, then select Line One, Line Two Page Up, Page Down, etc. or choose Back to change the POI category. 6 Once the POI has been selected, 7 just say Go and the route will calculate. 8

Find Address

If you choose to enter an address, you will be prompted to speak the name of the City, 12 the House Number, 13 the Street Name 14 and after making selections by voice commands or selecting line numbers (if prompted), the address can be calculated to a route by saying Go when the large green Go button 15 appears.

DNX9140 DDX814 DDX8034BT

GPS NAVIGATION SYSTEM MONITOR WITH DVD RECEIVER

INSTALLATION MANUAL

SYSTME DE NAVIGATION GPS MONITEUR AVEC RCEPTEUR DVD

MANUEL DINSTALLATION

SISTEMA DE NAVEGACIN GPS MONITOR CON RECEPTOR DVD

MANUAL DE INSTALACIN

B54-4722-00/00 (KW/RW)

Accessories

Installation Procedure
1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 9. Perform the Initial Setup. (Refer to the Instruction Manual.)

DNX9140 only

2WARNING
If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.

Acquiring GPS Signals

The first time you turn on DNX9140, you must wait while the system acquires satellite signals for the first time. This process could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter.

About the Front Panel

When removing the product from the box or installing it, the front panel may be positioned at the angle shown in (Fig. 1). This is due to the characteristics of a mechanism the product is equipped with. If the program that is activated when the product is first powered on works properly, the front panel will automatically move into the position (initial setting angle) shown in (Fig. 2).

(Fig. 1) (Fig. 2)

DNX9140//DDX814/DDX8034BT

After the Installation

After the installation, perform the Initial Setup by referring to the instruction manual.
Reception may drop if there are metal objects near the Bluetooth antenna.
Mounting and wiring this product requires skills and experience. For safetys sake, leave the mounting and wiring work to professionals. Make sure to ground the unit to a negative 12V DC power supply. Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. If the power is not turned ON (PROTECT is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. If your cars ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. If the fuse blows, first make sure the wires arent touching to cause a short circuit, then replace the old fuse with one with the same rating. Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Mount the unit so that the mounting angle is 30 or less. This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result.

Bluetooth antenna unit

CAUTION
Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. English |

Connection

Ignition key switch ACC
connect (red) and the battery If you(yellow) tothe ignition wire(ground), you may wire the car chassis cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

A B A B C

Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) (To car chassis) Antenna Cord FM/AM antenna input
Car fuse box Car fuse box (Main fuse)

Battery

Connect detectionto the vehicle's parking brake switch harness. Parking sensor wire (Light Green)

PRK SW

For the sake of safety, be sure to connect the parking sensor.
Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote
Reveres sensor wire (Purple/White)
Steering remote control input (Light Blue/Yellow)
To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on. Dimmer control wire (Orange/White) To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. Mute wire (Brown)
To connect the Kenwood navigation system, consult your navigation manual.
Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. Motor antenna control wire (Blue)
Power control wire (Blue/White)
If no connections are made, do not let the cable come out from the tab.
Bluetooth Microphone (Accessory #) (see page 8) Voice Control Switch (Accessory $) (DNX9140 only) (see page 8)

Cooling fan

GPS Antenna (Accessory !) (DNX9140 only) (see page 8)

FUSE ( 15A )

Accessory 1

REVERSE

REMO.CONT
White/Black White Gray/Black

ILLUMI

To front left speaker

To front right speaker

Green/Black Green Purple/Black

To rear left speaker

ANT. CONT

Purple

To rear right speaker

P CONT

English |

System Connection

iPod (commercially available)

USB terminal

USB device (commercially available) To MSN Direct Receiver KNA-M100 or TMC Tuner GTM10 (optional accessory) (DNX9140 only) Audio input (iPod/AV input 3 switchable) Resistance-free stereo type mini plug (3.5) Visual input (iPod/AV input 3 switchable) Resistance-free mini plug (3.5)
Accessory % (DNX9140 only) Receiver When connecting the MSN Direct TMC Tuner KNA-M100 (optional accessory) or Accessory 2 GTM10 (optional accessory), put the cable clamper (accessory %) to the back of this unit first, and then wire the cable through the clamper.

Accessory 3

Accessory 4

AV OUT

Audio/Visual output Visual output (Yellow) Audio left output (White) Audio right output (Red) Audio/Visual input Visual input (Yellow) Audio left input (White) Audio right input (Red) Audio/Visual input Visual input (Yellow) Audio left input (White) Audio right input (Red) Rear View Camera input Visual input (Yellow) Front Preout Audio left output (White) Audio right output (Red) Rear Preout Audio left output (White) Audio right output (Red) Subwoofer Preout Audio left output (White) Audio right output (Red) Center Preout

To Relay Box

| DNX9140//DDX814/DDX8034BT

CENTER

SUB WOOFER RELAY 2

REAR RELAY 1

REAR VIEW CAMERA

AV IN 2

AV IN1
Optional Accessory Connection
KCA-iP301V (Optional Accessory)
Visual Output (Yellow) Audio Output (Black)
USB device (commercially available) To SIRIUS Satellite Radio tuner/ XM Satellite Radio tuner/ HD Radio tuner (Optional Accessory)
adapter (optional accessory) may be Conversionfor connection of optional accessory. necessary Contact your Kenwood dealer for details.
Navigation System (Optional Accessory) (DDX814/ DDX8034BT only) TV Tuner (Optional Accessory) (DDX8034BT only)

TV ANTENNA INPUT

Connection cable (Included in the TV tuner)

TO MONITOR UNIT

Connection cable (Included in the Navigation System)
Installing the GPS Antenna (DNX9140 only)
GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. To mount the GPS antenna inside your vehicle: 1. Clean your dashboard or other surface. 2. Peel the backing off of the adhesive on the bottom of the metal plate (accessory @). 3. Press the metal plate (accessory @) down firmly on your dashboard or other mounting surface. You can bend the metal plate (accessory @) to conform to a curved surface, if necessary. 4. Place the GPS antenna (accessory !) on top of the metal plate (accessory @).
Installing the Talk Switch (DNX9140 only) and the Microphone Unit
1. Check the installation position of the microphone (accessory #) and the Talk switch (accessory $). 2. Remove oil and other dirt from the installation surface. 3. Install the microphone and the Talk switch. 4. Wire the cable up to the unit with it secured at several positions using tape or the like.

Accessory # Accessory $

Accessory !
Accessory @ Fix a cable with a commercial item of tape.
Depending on the type of car, reception of the GPS satellite signals might not be possible with an inside installation. The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with by these types of communication. Painting the GPS antenna with (metallic) paint may cause a drop in performance. Peel the release coated paper of double-face adhesive tape to fix on the place shown above.
Adjust the direction of the microphone to the driver.
Install the microphone as far as possible from the cellphone.
Installing the Escutcheon

For General Motors

1. Cut out accessory 6 to meet the shape of the opening of the center console. 2. Attach accessory 6 to the unit.
Cut out to meet the shape of the opening in the vehicle.

For Toyota/Scion

1. Cut out accessory 6 as illustrated.

Cutting line

Accessory 6

For Volkswagen

1. Attach accessory 0 to the unit.
2. Fold double-sided adhesive (accessory 7) along the slit and attach it to accessory 6 cut-out against the center rib as illustrated. Use 2 pieces of accessory 7 for 1 accessory 6 cut-out. 3. Attach accessory 6 cut-out to the unit.

Accessory 7

Accessory 0
Installation for Monitor/Player Unit
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.