HS33S-DP.BGBRLL_ENG

10/20/08

11:26 AM

Page 1
Model: HT33S (HT33S-DP, SH33S-F/A)
FOR THE GUARANTEE TERMS & CONDITIONS, PLEASE REFER TO BACK COVER OF THIS MANUAL.
Full HD up-scaling (1080p)
Home Theater Speaker ez Set-up
Listen sound from TV and Digital Device with 2.1ch mode.

Go to page 14

USB Direct Recording
Record music from CD to your USB device.

Go to page 16

Unique Features
View Full HD picture quality with simple setup.

Go to page 9

Portable In
Listen to music from your portable device (MP3, Notebook, etc).

Made for iPod

Enjoy music from iPod with simple connection.

Go to page 17

P/NO : MFL56962825

Page 2

Safety Precaution

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN
That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible. Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. This product is manufactured to comply with EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC. European representative : LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere, The Netherlands (Tel : +31-036-547-8940)
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction has been adhered to. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owners manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit;

*Touch sensor
This unit has sensitive controls that respond to the touch of your fingers. You can also change the volume by moving your finger around the touch wheel.
Precautions in using the touch buttons Use the touch buttons with clean and dry hands. - In a humid environment, wipe out any moisture on the touch buttons before using. Do not press the touch buttons hard to make it work. - If you apply too much strength, it can damage the sensor of the touch buttons. Touch the button that you want to work in order to operate the function correctly. Be careful not to have any conductive material such as metallic object on the touch buttons. It can cause malfunctions.
a POWER b DISC SLOT c EJECT d REMOTE SENSOR e DISPLAY WINDOW f TUNING DOWN & SKIP (.) g STOP
h TUNING UP & SKIP (>) i PLAY/PAUSE (N / X) j USB PORT k PORTABLE IN JACK l SYSTEM JACK
m COMPONENT VIDEO OUT JACKS n HDMI OUT JACK o OPTICAL IN JACK p iPod DOCK

Page 5

Remote control
a INPUT : Changes the input source ( AUX, AUX OPT, PORTABLE, USB, OSD IPOD, IPOD) SLEEP : Sets a certain period of time after which the unit will switch to standby. - Press SLEEP repeatedly to select the desired time period options (in minutes): (Dimmer on t Sleep timer value t Dimmer off) Dimmer on: The display window becomes dark and the touch wheel turns off. - To view the time countdown to the standby mode, press SLEEP again. - To deactivate the sleep timer, press SLEEP until the previous status is displayed or press POWER to switch the unit to standby. POWER: Switches the unit ON or OFF. FUNCTION : Selects the function (DVD/CD, FM) TITLE : If the current DVD title has a menu, the title menu appears on the screen. Otherwise, the disc menu may not appear. DISPLAY: Accesses On-Screen Display. MENU : Accesses the menu on a DVD disc. SETUP : Accesses or removes setup menu b PRESET(v/V): Selects programme of Radio. TUN.(-/+): Tunes in the desired radio station. b / B / v / V (left/right/up/down):Used to navigate on-screen displays. ENTER : Acknowledges menu selection. RETURN (O): Press to move backwards in the menu. REC (z) : USB Direct Recording c STOP (x): Stops playback or recording. PLAY (B): Starts playback. Mono/Stereo. PAUSE/STEP (X): Pause playback. SKIP(. / >): Go to next or previous chapter/ track. SCAN(bb/BB) : Search backward or forward. d t TVtHT SPK (Home theater Speaker ez Set-up): t Press HTt SPK to select the AUX OPT directly. MUTE : Press MUTE to mute your unit. You can mute your unit in order, for example, to answer the telephone. VOLUME (+/-) : Adjusts speaker volume. EQ : You can choose 6 (or 7) fixed sound impressions. VSM : Press VSM to set the VIRTUAL sound. REPEAT: Repeats a Chapter/ Track/ Title/ all. SUBTITLE: During playback, SUBTITLE repeatedly to select a desired subtitle language. 0-9 numerical buttons: Selects numbered options in a menu. e TV Control buttons : Controls the TV. (LG TV only) PROG./MEMO. : Accesses or removes Program menu. CLEAR: Removes a track number on the Program List. f RDS: Radio display mode PTY: Views the various displays of the RDS

Put the batteries into the remote control
Make sure that the + (plus) and (minus) on the batteries match those on the remote control.

Controlling the TV.

You can control the sound level, input source, and power switching of LG TVs as well. Hold POWER (TV) and press PR (+/) button repeatedly until the TV turns on or off.

Page 6

Making system connections
Connecting the main unit, speakers, and FM antenna to the active subwoofer.
a Connect the system jack marked MAIN to the main unit (SYSTEM). Secure the jack by tightening the two screws.

Front speaker (R)

Front speaker (L)
b Connect the system jack marked SPK to the active subwoofer (SYSTEM). Secure the jack by tightening the two screws.
cd Connect the speakers to the active subwoofer (SPEAKERS). Connect the red end of each wire to the terminals marked+ (plus) and black end to the terminals maked - (minus).
Active subwoofer The bottom of the speaker
e Connect the FM antenna for listening to the radio. Be sure to fully extend the FM antenna. After connecting the FM antenna, keep it as horizontal as possible.

Page 7

Connecting the video out to your TV.
Check the jacks of your TV, and choose the , Picture quality improves in order from A to C.
A B C To connect to a TV with the HDMI jack

connection.

Connect the HDMI cable from the HDMI OUT jack on the rear of the main unit to the HDMI IN jack on your TV. If your TV does not accept your resolution setting, abnormal picture appears on the screen. Use the HDMI Cable within 5 meters. If the volume bar is not displayed on TV screen, when you select Simplink to off on TV, restart the unit. Available resolution according to connection [HDMI OUT] : Auto, 1080p, 1080i, 720p and 480p (or 576p) [COMPONENT VIDEO OUT] : 480p (or 576p) and 480i (or 576i) [VIDEO OUT] : 480i (or 576i)
Listening to the sound from your analog component
Analog signal components such as VCR and TV.
A To connect to a TV with the video in jack
Connect the video cable from the VIDEO OUT on the rear of the active subwoofer to the video in jack on your TV. or To connect to a TV with the SCART jack Connect the RCA to SCART cable from the VIDEO OUT on the rear of the active subwoofer to the SCART jack on your TV.
B To connect to a TV with the component video in jacks

ON REMOTE

1 Connect the audio out of your analog component to the AUX IN (AUDIO L/R) on the rear of the active subwoofer: or Connect the SCART jack of your analog component to the AUX IN (AUDIO L/R) on the rear of the active subwoofer. 2 Select the AUX function:
If your TV has component video in, connect a component video cable from COMPONENT VIDEO OUT (Y, PB and PR) jacks on the rear of the main unit to the component video in jacks on your TV.

INPUT 7

Page 8
OSD Initial language settings - optional
Before using the unit for the first time, you have to adjust OSD initial language.

Adjust the settings

1 Display setup menu : 2 Select a desired option on the first level: 3 Move to second level: 4 Select a desired option on the second level: 5 Move to third level: 6 Change the setting: SETUP

vV B vV B v V, ENTER

1 Turn the power on: The language list display window appears 2 Select the language: 3 Press: 4 To confirm press: POWER

vV b B

b B and ENTER
Adjust the settings - more you can do
Adjust the language settings
OSD Select a language for the Setup menu and on-screen display. There is displayed as - or other error mark on display when you change OSD, do as follows; - Restart the unit - Change function - Disconnect and connect USB device. Disc Audio/Subtitle/Menu Select a language for the Menu/Audio/Subtitle. [Original]: Refers to the original language in which the disc was recorded. [Other]: To select another language, press number buttons then ENTER to enter the corresponding 4-digit number according to the language code list in the reference chapter (see page 18). If you make a mistake before pressing ENTER, press CLEAR [Off] (for Disc Subtitle): Turn off Subtitle.
Initial Setting the Area Code
The first time you use this unit, to set the Area Code you have to as below.
1 Display setup menu: 2 Select LOCK menu on the first level: 3 Move to second level: The activated Area Code appears on the second level.: 4 Move to third level: 5 Enter the new password: 6 Recheck entered new password: 7 Select a code for a geographic area: After select, Rating and Password will be activated.(page 18) 8 To confirm press: Make sure to finish setting the Area Code before leaving the setup menu if you cannot set the Rating and Password. 8 SETUP
B B numerical buttons (0-9) and ENTER numerical buttons (0-9) and ENTER

Page 9

Adjust the display settings
TV Aspect Select which screen aspect to use based on the shape of your TV screen. [4:3]: Select when a standard 4:3 TV is connected. [16:9]: Select when a 16:9 wide TV is connected. Display Mode If you selected 4:3, youll need to define how you would like widescreen programs and films to be displayed on your TV screen. [Letterbox]: This displays a widescreen picture with black bands at the top and bottom of the screen. [Panscan]: This fills the entire 4:3 screen, cropping the picture as necessary. Video Resolution - Use vV to select the desired resolution then press ENTER to confirm your selection. You can set 1080p video resolution to enjoy Full HD picture quality. (Full HD up-scaling) The number in 480p (or 576p), 720p, 1080p and 1080i indicates the number of lines of video. The i and p indicate interlaced and progressive scan, respectively. [Auto] If your HDMI jack is connected to TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV (1080p, 1080i, 720p or 480p (or 576p)). (only for HDMI connection) [1080p] Outputs 1080 lines of progressive video. (only for HDMI connection) [1080i] Outputs 1080 lines of interlaced video.(only for HDMI connection) [720p] Outputs 720 lines of progressive video.(only for HDMI connection) [480p (or 576p)] Outputs 480 (or 576) lines of progressive video. [480i (or 576i)] Outputs 480 (or 576) lines of interlaced video. Notes on Video Resolution Only resolutions supported by the TV are available. Depending on your TV, certain HDMI output resolutions may not work. If your TV does not accept your resolution setting, an abnormal picture appears on the screen. Please read TVs owners manual then set the resolution that your TV can accept. If the HDMI jack is connected for TVs providing display information (EDID), you can not select resolutions that the TV does not accept. If the picture does not appear on the screen, change the TVs input source. If you turn off the TV or disconnect the HDMI cable during playback of the device, the playback may pause. You have to click on the play button to play back again. For some TVs, when you change the TV mode, such condition specified above may happen.

Pause playback ALL

Symbol Used in this Manual
All discs and file listed below DVD and finalized DVDR/RW DivX files

ALL DVD DivX

Press PAUSE/STEP (X) to pause playback. Press PLAY (B) to continue playback.

MP3 WMA ACD

MP3 files WMA files Audio CDs
Frame-by-Frame playback DVD
Press PAUSE/STEP (X) repeatedly to play title Frame-by-Frame.

Playing repeatedly ALL

Press REPEAT repeatedly to select a desired repeat mode: track, all and off. The current title, chapter or track will be played back repeatedly. To return to normal playback, press REPEAT repeatedly to select [Off].

Page 12

Fast forward or fast reverse ALL
Press SCAN (m or M) to play fast forward or fast reverse during playback. You can change the playback speed by pressing SCAN (m or M) repeatedly. Press PLAY (B) to continue play at normal speed.
Mixed disc or USB Flash Drive DivX, MP3/WMA and JPEG
When playing a disc or USB Flash Drive containing with DivX, MP3/WMA and JPEG files together, you can select which menu of files you would like to play by pressing TITLE. Press ENTER after selecting MUSIC, PHOTO, or MOVIE by pressing b B.
Selecting a subtitle language DVD
During playback, press SUBTITLE ( language.
) repeatedly to select a desired subtitle
Changing the character set to display DivX subtitle correctly DivX
If the subtitle does not display properly during playback, press and hold SUBTITLE for about 3 seconds then press SUBTITLE to select another language code until the subtitle is displayed properly
Slow down the playing speed DVD
While playback is paused, press SCAN (bb or BB) to slow down forward or reverse playback. You can change the various playback speed by pressing SCAN (m or M) repeatedly. Press PLAY (B) to continue play at normal speed.
DivX file requirement DivX
DivX disc compatibility with this player is limited as follows: Available resolution size: 800x600 (W x H) pixel The file name of the DivX subtitle is available by 45 characters. If there is impossible code to express in the DivX file, it may be displayed as " _ " mark on the display. If the number of the screen frame is over 30 per 1 second, this unit may not operate normally. If the video and audio structure of recorded files are not interleaved, either video or audio is outputted. If the name of movie file is different from that of the subtitle file,during playback of a DivX file, subtitle may not be display. MPEG4 file extensions:.avi,.mpg,.mpeg Playable DivX subtitle: SubRip(*.srt/*.txt), SAMI(*.smi), SubStation Alpha(*.ssa/*.txt) MicroDVD(*.sub/*.txt) SubViewer 2.0(*.sub/*.txt) TMPlayer(.txt), DVD Subtitle System(.txt) (Files (VobSub(.sub)) included with USB device is not supported) Playable Codec format: DIVX3.xx, DIVX4.xx , DIVX5.xx, MP43, 3IVX Playable Audio format: AC3, DTS, PCM, MP3, WMA Sampling frequency: within 32 - 48 kHz (MP3), within 24 - 48kHz (WMA) Bit rate: within 32 - 320kbps (MP3), 40 - 192kbps (WMA) CD-R/RW, DVDR/RW Format: ISO 9660 Maximum Files/Disc: Less than 999 (total number of files and folders)

Watch and listen 1.5 times faster DVD
Press PLAY when a DVD is already playing to watch and listen to a DVD 1.5 times faster than normal playback speed. B x1.5 will appear in the top right corner of the screen. Press PLAY again to return to normal playback speed.
Viewing the Title menu DVD
Press TITLE to display the disc's title menu, if available.

Viewing the DVD MENU DVD

Press MENU to display the disc menu, if available.
Starting play from selected time DVD
Searches for the starting point of entered time code. Press DISPLAY during playback and select the time clock icon. Input the required start time in hours, minutes, and seconds and press ENTER. If you enter the wrong number, press CLEAR to enter again.

Last Scene Memory DVD

This unit memorizes the last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the player or switch off(Stand-by mode) the unit. If you load a disc that has the scene memorized, the scene is automatically recalled.
Displaying file information (ID3 TAG ) MP3
While playing an MP3 file containing file information, you can display the information by pressing DISPLAY repeatedly.

Screen Saver

The screen saver appears when you leave the unit in Stop mode for about five minutes.

Page 13

Creating your own program ACD
You can play the contents of a disc in the order you want by arranging the order of the music files on the disc. The program is cleared when the disc is removed. Select a desired music file then press PROG./MEMO. or select and then press ENTER to add the music file to the program list. To add all music files on the disc, select and then press ENTER. Select a music file from the program list then press ENTER to start programmed playback.To clear a music file from the program list, select the music file you want to clear then press CLEAR or select icon and then press ENTER. To clear all music files from the program list, select " " then press ENTER.

Viewing photo files

1 Insert a Disc in the slot: (On unit) 2 Select a photo file: 3 Display the selected file in full screen: 4 To return to the menu: vV ENTER x STOP

Viewing photo files - more you can do
Viewing photo files as a slide show
Use vV b B to highlight ( ) icon then press ENTER to start slide show. You can change slide show speed using b B when ( ) icon is highlighted. If X is selected, the slide show dose not operate.
MP3/WMA music file requirement
MP3/WMA compatibility with this unit is limited as follows:
File extensions:.mp3,.wma. Sampling frequency: within 32 - 48 kHz (MP3), within 24 - 48kHz (WMA) Bit rate: within 32 - 320kbps (MP3), 40 - 192kbps (WMA) CD-R/RW, DVDR/RW Format: ISO 9660 Maximum Files/Disc: Less than 999 (total number of files and folders)
Skip to the next/previous photo
Press SKIP (. or >) to view the previous/next photo.

System Select

You must select the appropriate system mode for your TV system. If NO DISC appears in the display window, press and hold PAUSE/STEP (X) on the remote control for more than five seconds to be able to select a system.

Rotate a photo

Use vV b B to rotate the photo in full screen mode.

Pause a slide show

Press PAUSE/STEP (X) to pause a slide show. Press PLAY (B) to continue the slide show.

Photo file requirement

JPEG file compatibility with this unit is limited as follows:
File extensions:.jpg Photo size: Normal - within 5120 x 3840 (W x H) pixels. Progressive - within 2048 x 1536 (W x H) pixels CD-R/RW, DVDR/RW Format: ISO 9660 Maximum Files/Disc: Less than 999 (total number of files and folders)

Page 14

Listening to the radio
Be sure that FM antenna is connected.
See information about a radio station
The FM tuner is supplied with the RDS (Radio Data System) facility. This shows information about the radio station being listened to. Press RDS repeatedly to cycle through the various data types: PS PTY RT (Programme Service Name) The name of the channel will appear in the display (Programme Type Recognition) The programme type (e.g. Jazz or News) will appear in the display. (Radio Text) A text message contains special information from the broadcast station. This text may scroll across the display. (Time controlled by the channel) This shows the time and date as broadcast by the station.

1 Turn the power on: 2 Select FM: 3 Select a radio station: 4 To save a radio station: A preset number will show in the display. Up to 50 radio stations can be saved. 5 To confirm press: 6 To select a saved station: POWER FUNCTION TUN.-/+ PROG/MEMO.

PROG/MEMO. PRESET v/V

Listening to the radio - more you can do
Look for radio stations automatically
Press and hold TUN.-/TUN.+ for more than a second. The tuner will scan automatically and stop when it finds a radio station.
Listen to sound from TV and Digital Device with 2.1ch mode. Even in power off mode, if you press TVtHT SPK, then power is on and automatically changed to AUX OPT mode.
Choose a preset number for a radio station
When storing a radio station, the preset number can be chosen. When this unit automatically shows a preset number, press PRESET v/V to change it. Press PROG./MEMO. to save your chosen number.
Delete all the saved stations
Press and hold PROG./MEMO for two seconds. ERASE ALL will flash up on the display. Press PROG./MEMO to erase all saved radio stations.
Improve poor FM reception
Press PLAY (B) on the remote control. This will change the tuner from stereo to mono and usually improve the reception.
1 Connect the main units OPTICAL IN jack
to jack on optical out of your TV (or Digital Device etc.).:
t TVtHT SPK t TVtHT SPK, FUNCTION, or INPUT
2 Select the AUX OPT function:
To select the AUX OPT directly
3 Listen sound with 2.1ch speaker.: 4 To escape from AUX OPT 14

Page 15

Listening to music from your USB device
The advantage of connecting your portable USB player through the systems USB port is that the USB device can be controlled from the system.
Listening to music from your USB device more you can do

Compatible USB Devices

Devices which require additional program installation when you have connected it to a computer, are not supported. MP3 Player : Flash type MP3 player. The MP3 player requiring installation of a driver is not supported. USB Flash Drive : Devices that support USB2.0 or USB1.1. (In case USB 2.0, it operates at the same speed as that of USB 1.1)

USB device requirement

Do not extract the USB device while in operation. To prevent data loss, back up all data. If you use a USB extension cable or USB hub, the USB device might not be recognized. A device using NTFS file system is not supported. (Only FAT (16/32) file system is supported.) The USB function of this unit does not support all USB devices. Digital camera and mobile phone are not supported. This unit is not supported when the total number of files is 1000 or more. If the connected USB device has two or more folders, a drive folder is displayed on the screen. If you want to move to the previous menu after you select a folder, press RETURN. In case of Multi card reader, video files can not be played.

1 Connect the USB device to the unit: 2 Select the USB function: 3 Select a file from the menu: 4 Start your music playing: 5 Before disconnecting the portable USB device, change to any other function by pressing: 6 Remove the USB device: INPUT vV BPLAY

FUNCTION or INPUT -

Page 16
Recording music from CD to your USB device
1 Connect the USB device to the unit: 2 Select the DVD/CD function: 3 Start the recording: If you want to record a desired music file in disc to USB, record after playing back the file. 4 To stop a recording: FUNCTION z REC v V, PLAY (N) and z REC x STOP
If you record more 999 files on CD_REC folder, ERROR appears on the display window. New files are numbered in numeric sequence. If the total number of the files are more than 999, delete some or store some in PC. External HDD, Multi Card reader, Locked device and MP3 player is not supported. If you turn off and then on TV when the connected TV is HDMI mode, nothing may be displayed on screen during USB recording. To solve the problem, stop the USB direct recording.
The making of unauthorized copies of copy-protected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. Be responsible Respect copyrights
Recording music from CD to your USB device - more you can do
Record Audio CD source to USB
One track recording - If the USB recording is started during playback of the CD, the only track would be recorded into the USB. All track recording - If the REC button is pressed at the CD stop, all track would be recorded. Program list recording - USB Records after selecting the tracks pressing the PROG./MEMO. button if you want to record the track you want. (Refer to Creating your own program on page 13.)
Listening to music from your portable player
The player can be used to play the music from many types of portable player
When you are recording, look out for the following
Do not remove the USB device during USB recording. If not, an incomplete file may be made and not deleted on PC. When you start the USB direct recording, you can check the recording percentage rate on the screen. During the recording is no sound and not operate for volume. When you stop recording, the file that has been recorded at that time will be stored. Playable USB REC. Bit rate : 96/128kbps (Refer to Bit Rate on page 10.) PAUSE/STEP (X) button does not operate during USB recording. USB port of the unit cannot be connected to PC. The unit cannot be used as a storage device. If the USB recording is not available, NO USB,.ERROR, USB FULL, NO REC appear on the display window. File will be stored to CD_REC folder as a format TRK-001.MP3. CD-G disc and the disc encoded with DTS are not recorded to USB.

3.5mm stereo miniplug cable
1 Connect the headphone (or line out ) jack of the portable player into the PORT. IN on the right side of the main unit: 2 Turn the power on: 3 Select the PORTABLE function: 4 Turn the portable player on and start it playing:

POWER INPUT -

Page 17
Listening to music from your iPod
iPod mode: You can operate your iPod by using the supplied remote control and controls on your iPod. TV screen is turned off. iPod will not be charged when selecting the iPod mode. But you can enjoy better sound quality. OSD iPod mode: You can operate your iPod by controlling OSD menu on the TV screen with supplied remote control. The controls on your iPod are not operational in the OSD iPod mode. If you want to charge the iPod while listening to music, selects the OSD iPod mode.
To open the iPod dock door: Press the marked iPod v on the iPod dock door and push it backwards.
Listening to music from your iPod - more you can do
Pause playback OSD iPod mode

iPod mode

Skip to the next/previous file OSD iPod mode
Press SKIP (>) to move to the next file. Press SKIP (.) to return to the beginning of the current file. Press SKIP (.) twice briefly to step back to the previous file.
Fast forward or fast reverse OSD iPod mode
During playback, press and hold SCAN (m or M) and then release at a point you want.
Playing repeatedly OSD iPod mode
Press REPEAT repeatedly to select a desired repeat mode : track, all and off.
iPod message OSD iPod mode
Please, check your iPod - If the power of your iPod is insufficient or the iPod is misconnected or unknown device. Reset the iPod if the iPod is not operating normally (Refer to http://www.apple.com/support/)
1 Connect your iPod to the Dock on the top of the main unit: 2 Turn the power on: 3 Select the iPod or OSD iPod function: 4 Select the menu: 5 Select a file: 6 Start the file playing: 7 To stop the file playing: To move the previous mode, press MENU on the remote control. 8 Before disconnecting the iPod, change to any other function by pressing: 9 Remove the iPod: POWER INPUT v V ENTER vV B PLAY or ENTER x STOP

Compatible iPod

Compatibility with your iPod may vary depending on the type of your iPod. Depending on your iPods software version, it may not be possible to control your iPod from the unit. We recommend installing the latest software version.
When you use iPod, look out for the following
Interference may happen depending on iPod devices. The video or photo file is not displayed. When iPod is connected with dock connector, it may result in malfunctions of this unit.

Page 18

Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.
Language Afar Afrikaans Albanian Ameharic Arabic Armenian Assamese Aymara Azerbaijani Bashkir Basque Bengali; Bangla Bhutani Bihari Breton Bulgarian Burmese Byelorussian Chinese Code 9072 Language Croatian Czech Danish Dutch English Esperanto Estonian Faroese Fiji Finnish French Frisian Galician Georgian German Greek Greenlandic Guarani Gujarati Code 7185 Language Hausa Hebrew Hindi Hungarian Icelandic Indonesian Interlingua Irish Italian Javanese Kannada Kashmiri Kazakh Kirghiz Korean Kurdish Laothian Latin Latvian, Lettish Code 7686 Language Lingala Lithuanian Macedonian Malagasy Malay Malayalam Maori Marathi Moldavian Mongolian Nauru Nepali Norwegian Oriya Panjabi Pashto, Pushto Persian Polish Portuguese Code 8084 Language Quechua Rhaeto-Romance Rumanian Russian Samoan Sanskrit Scots Gaelic Serbian Serbo-Croatian Shona Sindhi Singhalese Slovak Slovenian Spanish Sudanese Swahili Swedish Tagalog Code 8476 Language Tajik Tamil Telugu Thai Tonga Turkish Turkmen Twi Ukrainian Urdu Uzbek Vietnamese Volapk Welsh Wolof Xhosa Yiddish Yoruba Zulu Code 9085

Area Codes

Choose a area code from this list.
Area Afghanistan Argentina Australia Austria Belgium Bhutan Bolivia Brazil Cambodia Canada Chile China Colombia Congo Code AF AR AU AT BE BT BO BR KH CA CL CN CO CG Area Costa Rica Croatia Czech Republic Denmark Ecuador Egypt El Salvador Ethiopia Fiji Finland France Germany Great Britain Greece Code CR HR CZ DK EC EG SV ET FJ FI FR DE GB GR Area Greenland Hong Kong Hungary India Indonesia Israel Italy Jamaica Japan Kenya Kuwait Libya Luxembourg Malaysia Code GL HK HU IN ID IL IT JM JP KE KW LY LU MY Area Maldives Mexico Monaco Mongolia Morocco Nepal Netherlands Netherlands Antilles New Zealand Nigeria Norway Oman Pakistan Panama Code MV MX MC MN MA NP NL AN NZ NG NO OM PK PA Area Paraguay Philippines Poland Portugal Romania Russian Federation Saudi Arabia Senegal Singapore Slovak Republic Slovenia South Africa South Korea Spain Code PY PH PL PT RO RU SA SN SG SK SI ZA KR ES Area Sri Lanka Sweden Switzerland Taiwan Thailand Turkey Uganda Ukraine United States Uruguay Uzbekistan Vietnam Zimbabwe Code LK SE CH TW TH TR UG UA US UY UZ VN ZW

Page 19

Troubleshooting

PROBLEM

No power No picture
The power cord is disconnected. The TV is not set to receive the DVD signal. The video cables are not connected securely.

CORRECTION

Plug the power cord into the wall outlet securely. Select the appropriate video input mode on the TV so the picture from the DVD Receiver appears on the TV screen. Connect the video cables securely to both the TV and DVD Receiver. Select the correct input mode of the audio receiver so you can hear the sound from the DVD receiver. Connect the audio cables into the connection terminals correctly. Replace with a new audio cable. Clean the disc using a soft cloth with outward strokes. Insert a disc Insert a playable disc (check the disc type, colour system and regional code). Place the disc with the label or printed side facing upwards. Press SETUP to close the menu screen. Enter your password or change the rating level. Clean the disc using a soft cloth with outward strokes. Move DVD receiver and audio components further away from your TV. Check the antenna connection and adjust its position. Attach an external aerial if necessary. Tune to the station manually. Preset some radio stations, see page 14 for details. Point the remote directly at the unit. Use the remote within 23 feet (7m) of the DVD receiver. Remove the obstacle. Replace the batteries with new ones. Switch off dimmer. (Refer to SLEEP on page 5)

There is little or no sound
The DVD picture quality is poor A DVD/CD will not play
Equipment connected via the audio cable is not set to receive DVD signal output. The audio cables are not connected to the speakers or receiver securely. The audio cables are damaged. The disc is dirty. No disc is inserted. An unplayable disc is inserted. The disc is inserted upside down. The menu is open on screen. There is a parental lock which prevents the playback of DVDs with a certain rating. The disc is dirty. The DVD receiver is located too close to the TV, causing feedback. The antenna is positioned or connected poorly. The signal strength of the radio station is too weak. No stations have been preset or preset stations have been.cleared(when tuning by scanning preset channels). The remote is not pointed directly at the DVD receiver. The remote is too far from the DVD receiver. There is an obstacle in the path between the remote control and the unit. The batteries in the remote control are flat. The dimmer function is activated.
Humming noise heard while a DVD or CD is playing Radio stations cant be tuned in properly
The remote control doesnt work well / at all
The display window becomes dark and the touch wheel turns off.

Page 20

Types of Playable Discs
DVD-VIDEO: Discs such as movies that can be purchased or rented. DVD-R: Video mode and finalized only DVD-RW: Video mode and finalized only DVD VR format that have been finalized can not be played in this unit DVD+R: Video mode only Supports the double layer disc also DVD+RW: Video mode only Audio CD:

About the

Symbol Display
may appear on your TV display during operation and indicates that the function explained in this owners manual is not available on that specific DVD video disc.

Regional Codes

This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or ALL. Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your units regional code or the disc cannot play. If you try to play a DVD with a different regional code from your player, the message Check Regional Code appears on the TV screen.

Copyrights

It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs picture noise will appear. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE STANDARD DEFINITION OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players. (Mastered/Live File System : Disc format system for Windows Vista)

To obtain information or assistance: Call 5454 Monday-Friday 9.00am-4.30pm MODEL NO.* SERIAL NO.* DATE OF PURCHASE.*
Please complete for your own record
In all cases of difficulty - consult your LG dealer from whom the product was purchased
LGEUK Website : www.lge.co.uk ( service website : www.lgelectronics.co.uk )

LASYSTEMS - Brusselsesteenweg 208 - 1730 Asse - Belgium
Phone: +32-2-4531312 - Fax: +32-2-4531763 E-mail: info@lasystems.be
Lg HT33S Home cinema system 300W (HT-33S)

Price details:

Price excl. VAT: 265.38 Eco fees: 0.33 VAT 21 %: 55.80
PDF generated on: 6 June, 2011

Product details:

Product code: HT-33S EAN: Manufacturer: LG

321.51

* VAT included / Main specifications:
Product is discontinued. You can not order it anymore.
*PLEASE NOTE: Every effort has been made to ensure the accuracy of all information contained herein. Lasystems makes no warranty expressed or implied with respect to accuracy of the information, including price, editorials or specifications. Lasystems or its suppliers shall not be liable for incidental, consequential or special damages arising from, or as a result of, any electronic transmission or the accuracy of the information contained herin, even if Lasystems has been advised of the possibility of such damages. Product and manufacturer names are used only for the purpose of identification.