TT1600MKII TT1610
PROFESSIONAL DJ TURNTABLE
Quick Start Owners Manual (ENGLISH)
BOX CONTENTS Turntable Aluminum Platter w/Belt Pre-Mounted Cartridge 45 RPM Adapter Counterweight
Manual de inicio rpido para el usuario (ESPAOL)
CONTENIDOS DE LA CAJA: Giradiscos Plato de aluminio con correa Cartucho pre-montado Adaptador de 45 RPM Contrapeso
Gebrauchsanweisung zur schnellen Inbetriebnahme (DEUTSCH)
SCHACHTELINHALT Plattenspieler Aluminium-Drehteller mit Riemen Vorgefertigtes Einbaumodul 45 RPM-Adapter Gegengewicht
Guide dutilisation rapide (FRANAIS)
Contenu de la bote Platine tourne-disque Plateau en aluminium avec courroie Cartouche prmonte Adaptateur 45 tr/min Contrepoids
Manuale Rapido di Utilizzazione (ITALIANO)
CONTENUTO DELLA CONFEZIONE Giradischi Piatto in Alluminio con Cinghia Cartuccia Pre-Installata Adattatore 45 giri Contrappeso
(ENGLISH) QUICK START GUIDE 1. 2. 3. Make sure all items listed on the front of this guide are included in the box. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT Go to http://www.numark.com for product registration.
GENERAL CONTROLS 1. Power Cable: This power cable should be plugged into a wall receptacle AFTER all audio connections are made. 2. RCA Audio Output Cables: These cables are used to connect the turntable to a DJ mixer or amplifier that has a built in PHONO PREAMP. This RCA type input is a feature that is commonly found on most DJ mixers and will be labeled PHONO or TURNTABLE. If the RCA Audio Output Cables are not connected to a mixer or amplifier with a PHONO PREAMP, then the audio output will be very quiet. 3. Ground Wire: This ground wire must be connected to a metal bolt or ground lug that is on the mixer or amplifier that the turntable is connected to. If the ground wire is not securely fastened to a metal bolt or ground lug, then the audio output will exhibit a buzzing sound. 4. Power Button: This ring around the power button illuminates red when the turntable is switched on. 5. Platter: This aluminum platter must be securely fastened to the turntable prior to operation. The Motor Drive Belt can be found on the drive ring underneath the platter. See SETUP INSTRUCTIONS for detailed information on installing the Motor Drive Belt. 6. Start/Stop Buttons: These buttons start and stop the turntable motor. Both buttons have the same function. If they seem to not be functioning, check to make sure that the Motor Drive Belt is properly installed in the SETUP INSTRUCTIONS. 7. Target Lamp Power Jack: This RCA Jack supplies power to the an accessory Target Lamp (NOT INCLUDED.) Note: IT HAS NO AUDIO FUNCTION-DO NOT CONNECT AUDIO CORDS TO THIS POWER JACK The Target Lamp shines light across the vinyl record grooves to help identify track marks in low light situations. 8. 33 and 45 RPM Buttons: These buttons control the RPM of the turntable platter. A red LED indicates which RPM mode has been selected. NOTE: If the turntable is powered down while in the 45 RPM setting, it will return to 33 RPM when it is powered up. 9. Pitch LED: This LED illuminates green when the pitch slider is set at 0%. When the pitch slider is moved away from zero, the LED illuminates red. 10. Pitch Slider: This slide control allows the pitch to be increased or decreased by 10%. In the center position the pitch is at 0%. When moved away from the center and towards the tone arm decreases the pitch (slows down the platter) and moving the pitch slider away from the tone arm increase the pitch (speeds up the platter.) TONE ARM: Items are all parts of the Tonearm. Refer to the TONEARM SETUP section for additional details on these controls. Your model will be equipped with straight arm or S-arm style depending upon model purchased. 11. 12. 13. Counter Weight and Scale Ring: The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. Anti-Skate Adjustment: This knob is used to compensate for inward tracking forces. See TONEARM SETUP for more details. Arm Clip: This specially designed arm clip secures the tone arm while at rest or when not in use. The arm clip has been designed to remain in the up position while unlocked. NOTE: When transporting the turntable, it is always recommended that the headshell be removed and the arm clip secured to prevent tonearm or turntable damage. Tone Arm Lock Nut: This Aluminum nut is used to secure the head shell and cartridge assembly to the tone arm tube. See Cartridge Setup for more details.

PLATTER SETUP

WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability or permanent motor damage. 1. 2. 3. 4. Start by placing the rubber drive belt around the inner bottom ring of the turntable platter. This should come preinstalled, but check to make sure that it is not twisted or damaged. Install the Platter on the center spindle and press it down firmly. Check to make sure that it rotates uniformly and does not wobble excessively. Rotate the platter so that the one of the holes is aligned with the Start Stop button on the front corner of the turntable. The brass motor spindle should be visible through this hole. Reach into the hole and pull the rubber drive belt off of the inner ring, and install it over the motor spindle. Be careful not to twist the rubber drive belt during this step. Check to make sure the platter rotates uniformly. If the drive belt is properly installed, there should be a slight amount of tension that brings the platter to a stop after spinning it freely.

TONEARM SETUP

Begin by rotating the counterweight clockwise until it is in the complete forward position (NOTE: this is also the maximum amount of pressure that can be applied to the cartridge.) Now there should be a feeling of weight and resistance when the head shell is raised and lowered. Begin rotating the counterweight counter-clockwise (away from the pivot point) until the weight and resistance feeling is gone. If done properly, the tone arm will pivot with very little resistance back and forth indicating that there is exactly 0 grams of stylus pressure. With the counterweight in its new position further away from tone arm pivot point, grasp the scale ring of the counter weight and rotate it until "0" is in the vertical position. Finally, rotate the counterweight (and scale ring) clockwise (towards the pivot point) until the desired amount of weight is reached. If the scale rotates 360 degrees beyond the zero point, the new scale ring reading should be added to 3.5. *The included head shell and cartridge assembly requires a minimum of 3 grams and no more than 5 grams for optimum performance.

www.Numark.com

P: [401] 658.3131 // F: [401] 658.3640

DJ PACKS

DJ IN A BOX
Vinyl + iPod DJ Package Everything you need to perform and record with vinyl and iPod. DJ IN A BOX is a turntable pack for performing with vinyl, iPod or iPhone, and more. DJ IN A BOX features iM1, the worlds first DJ mixer that records your mix to your iPod or iPhone. You can also perform with tracks from your iPod, connect optional gear like CD players, mics, and preview your mix in HF125 DJ headphones. TT1610 BELT-DRIVE TURNTABLES Pitch-adjustable DJ turntables with aluminum platters and performance controls. Complete with slipmats, cartridges, and connection cables. iM1 TWO-CHANNEL MIXER WITH DOCK FOR iPod Rugged, reliable faders, replaceable crossfader, and a built-in dock for iPod. Record your set to iPod and mix in tracks from iPod. HF125 DJ HEADPHONES Cue in comfort and enjoy clean, clear sound on stage or at home.

Features:

iM1, the first DJ mixer that enables you to play
from and record your mix to iPod or iPhone
Professional TT1610 belt-drive turntables
All information is preliminary and subject to change.
deliver powerful, reliable performance High-quality HF125 DJ headphones provide clean, clean, comfortable cueing Includes all the little pieces you need: slipmats, cartridges, and connection cables Two-channel mixer has inputs for turntables or CD players Dock for iPod compatible with all docking iPod and iPhone models Turntables feature 10 pitch control, 33/45 RPM speeds, and dual start/stop buttons
iPod and iTunes are trademarks of Apple, Inc. registered in the U.S. and other countries iPod not included