320_UXJCA_EN.book 18

Connecting the USB (external storage) device
Caution Be sure to turn the players power off before connecting or disconnecting external storage devices. Use empty external storage devices (on which nothing is stored).
Connecting via an Ethernet hub
The player can be connected to an Ethernet hub using a LAN cable.
VIDEO COMPONENT VIDEO Y CENTER SUB W
When using an external hard disk as the external storage device, be sure to turn on the hard disks power before turning on the players power. If the external storage device is write-protected, be sure to disable the write-protection. When connecting the USB cable, hold onto the plug, set the plug in the proper direction for the port and insert it horizontally. Placing excessive loads on the plug may result in poor contact, making it impossible to write data on the external storage device. The player is equipped with an internal storage. This internal storage cannot be used when an external storage device is connected. When a USB memory device or external hard disk is connected and the players power is turned on, do not unplug the power cord.
LAN cable (commercially available) Ethernet hub (router with hub functionality)

LAN 1 WAN

Internet
Note LAN on the players front panel display lights when there is an active local area network (LAN) connection (page 12). If there is an available DHCP server in your local area network, the IP address is obtained automatically. Otherwise, set IP address manually (page 43). For some Internet service providers, you may have to set the individual network configuration manually. In this case, see page 43. Pioneer is not responsible for any malfunction of the player due to communication error/malfunctions associated with your network connection and/or your connected equipment. Please contact your Internet service provider or network device manufacturer.

USB memory device, etc.

USB cable (commercially available)

Hard disk, etc.

Connecting the power cord
Connect the power cord after all the connections between devices have been completed.

Dolby Digital Out Dolby Digital 1 * Only valid for the DIGITAL OUT terminal. Dolby Digital 2 Dolby Digital PCM DTS Out DTS 1 * Only valid for the DIGITAL OUT terminal. DTS 2 DTS PCM
AAC Out AAC * Only valid for the DIGITAL OUT terminal. AAC PCM

DTS Downmix

Stereo
Audio Output Mode * Only valid for the AUDIO OUT terminals. Speaker Setup * Only valid for the AUDIO OUT terminals. Speaker Distance * Only valid for the AUDIO OUT terminals. Channel Level * Only valid for the AUDIO OUT terminals.

2 Channel Multi-channel

When an AV receiver or amplifier, etc., is connected to the players AUDIO OUT terminals, set whether or not speakers are connected to an AV receiver or amplifier, etc., their size and their crossover frequency. For details, see Changing the speaker setup on page 42. Specify the distance of your speakers from your listening position (page 42).

Fix Variable

The output for the various speakers is set to the maximum. The output level of the various speakers is set within the range of 6.0 dB to +6.0 dB (in 0.5 dB steps) (page 42).

320_UXJCA_EN.book 39

Setting HDMI Network HDMI High Speed Transmission

Options On Off

Explanation Select this when connected with a High Speed HDMI cable (page 14). Select this when connected with a Standard HDMI cable (page 14).
The players setting screen is closed if the output video resolution is switched by changing the HDMI High Speed Transmission setting. HDMI Color Space Auto YCbCr 4:4:4 YCbCr 4:2:2 RGB (16 to 235) Select this to automatically switch the video output between YCbCr and RGB signals according to the connected equipment. Select this to output the video signals as YCbCr 4:4:4 signals. Select this to output the video signals as YCbCr 4:2:2 signals. Select this to output the video signals as RGB signals. Choose this if the colors seem too dense and all the dark colors are displayed in a uniform black when RGB (0 to 255) is selected. Select this to output the video signals as RGB signals. Choose this if the colors seem too faint and the black seems too bright when RGB (16 to 235) is selected.

RGB (0 to 255)

Normally it is recommended to set this to Auto. When set to Auto, the optimum video signals for your TV are output. HDMI Audio Out Auto The signals are output with as many audio channels as possible. In cases when the number of channels does not decrease when the signals are output as such without converting them to linear PCM, they are output as such (page 47). Select this when you want the secondary audio and interactive audio signals to be mixed for output or when you want to output prioritizing sampling frequency over the number of channels (page 47). Select this when you do not want to output the audio from the HDMI output terminal. Select this to control the player with the remote control of the AV device connected using an HDMI cable. Also refer to About KURO LINK function on page 15. Select this when you do not want to control the player with the remote control of the AV device connected using an HDMI cable. Select this when you want the TV to turn on each time playback is started or the Home Menu or Home Media Gallery is displayed on the player. Select this when you do not want the TV to turn on each time playback is started or the Home Menu or Home Media Gallery is displayed on the player. Select this when you want the players power to turn off together with the TVs power. Select this when you do not want the players power to turn off together with the TVs power. Enables PQLS function (page 15). Disables PQLS function (page 15).

Setting the proxy server

Only set the proxy server if so instructed by your Internet service provider. 1 Select and set Network Proxy Server Next Screen. Use / to select, then press ENTER. 2 Select and set Use or Not use at Proxy Server. Use / to change, then press.
Network BD PLAYER Proxy Server Proxy Server Server Select Method Server Name Port Number Use Server Name

Setting the IP address

1 Select and set Network IP Address Next Screen. Use / to select, then press ENTER. 2 Set IP address. Use /// to set the IP address of the player or DNS server, then press ENTER.
Network BD PLAYER IP Address Auto Set IP Address
IP Address Subnet Mask Default Gateway
Use Select this when using a proxy server. Not use Select this when not using a proxy server.
If you have selected Use, proceed to step 3. 3 Select and set Server Select Method. Use / to change, then press. IP Address Input the IP address. Server Name Input the server name. 4 Input IP Address or Server Name. Use the number buttons (0 to 9) to input the number if you select IP address by step 3. Use / to move the cursor. Use the number buttons (0 to 9) to input characters if you select Server Name by step 3. The characters that can be input for the server name are listed on the table below. Pressing a button repeatedly cycles through the characters shown.
Auto Set DNS Server Address
DNS Server (Primary) DNS Server (Secondary)
Auto Set IP Address On The players IP address is obtained automatically. Select this when using a broadband router or broadband modem that has a DHCP (Dynamic Host Configuration Protocol) server function. This players IP address will automatically be allocated from the DHCP server.

320_UXJCA_EN.book 44

If you want to enter two characters in succession that are both on the same button (for example a P and an R), press after inputting the first character then input the second character. Use CLEAR to delete the last character. Use / to move the displayed characters when all the input characters cannot be displayed.
Key Characters 1. abc2 def3 ghi4 jkl5 Key Characters mno6 pqrs7 tuv8 wxyz9 0
4 Change the language. Use / to change, then press ENTER.
Initial Setup BD PLAYER Audio Language Video Out Audio Out Language English Speakers HDMI Number Network Language Data Management Setup Navigator
Input Port Number. Press , use the number buttons (0 to 9) to input the number. Press ENTER to set.
The language can also be changed using the number buttons. Use / to move the cursor to Number, use the number buttons (0 to 9) to input the number, then press ENTER. Refer to Language Code Table and Country/Area Code Table on page 49. Note If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected and played.

Displaying the network settings
Select and set Network Display Network Configuration Next Screen. Use / to select, then press ENTER. The MAC address, IP address, subnet mask, default gateway and DNS server (primary and secondary) settings are displayed. When Auto Set IP Address is set to On, the values obtained automatically are displayed. Note 0.0.0.0 is displayed when each IP address has not been set.
Erasing data that has been added to BDs and application data
Use this procedure to erase data that has been added to BDs (data downloaded with the BD-LIVE function and data used with the BONUSVIEW function) and application data. Caution Some time is required to erase the data. Do not unplug the power cord while data is being erased. This operation does not work when a disc is loaded. 1 Select and set Data Management. Use / to select, then press ENTER. 2 Select and set the erase menu. Use / to select, then press ENTER. Individual/Shared Data Erase Use this procedure to select and erase data downloaded with the BD-LIVE function and data used with the BONUSVIEW function (page 9). Select Next Screen, then press ENTER. The list screen appears.
Individual/Shared Data Erase BD PLAYER Shared Data Disc Name 1 Disc Name 2 Disc Name 3 Disc Name 4 Disc Name 5 Disc Name 6 Disc Name items
Testing the network connection
Select and set Network Connection Test Start. Use / to select, then press ENTER. Network connection test completed successfully. is displayed once the test is completed. If any other message is displayed, check the connections and/or settings (pages 18 and 43).
Changing to other language at language setting
1 Select and set Language. Use / to select, then press ENTER. 2 Select and set Audio Language, Subtitle Language or BDMV/DVD-Video Menu Lang. Use / to select, then press ENTER. 3 Select and set Other. Use / to select, then press ENTER.

320_UXJCA_EN.book 45

When a disc name is selected, the data downloaded with the BD-LIVE function and data used with the BONUSVIEW is erased. When Shared Data is selected, all the data downloaded with the BD-LIVE function and not associated to discs is erased. Use / to select the data to be erased, then press ENTER. Application Data Erase Use this procedure to erase BD-ROM application data (high scores of games, bookmarks data, etc.). Select Start, then press ENTER. Storage Format Use this procedure to format the storage in which the data downloaded with the BD-LIVE function and data used with the BONUSVIEW function is stored (page 9). When this is done, all the data on the external storage device is erased. Select Start, then press ENTER. 3 Select Yes, then press ENTER. Use / to select, then press ENTER.

320_UXJCA_EN.book 48

9. When the output video resolution is set to 480i or 480p, the signals may be output in linear PCM (2 channels) or Dolby Digital bitstream, depending on HDMI High Speed Transmission setting and/or the connected HDMI device (page 14). 10. If the connected HDMI device is not compatible with DTS-HD Master Audio or DTS-HD High Resolution Audio, the signals are output in linear PCM (7.1 channels) or DTS Digital Surround bitstream. If the connected HDMI device is not compatible with DTS Digital Surround bitstream, the signals are output in linear PCM (2 channels). 11. When the output video resolution is set to 480i or 480p, the signals may be output in linear PCM (2 channels) or DTS Digital Surround, depending on HDMI High Speed Transmission setting and/or the connected HDMI device.
Note Only compatible with 7.1-channel surround back. 6.1-channel surround back is output in 7.1 channels. In other cases, output as audio signals of 5.1-channels or less. When outputting linear PCM audio signals, if the number of compatible channels of the connected HDMI device is lower, the signals are output with the number of channels for which the device is compatible. The audio signals output from the DIGITAL OUT terminal have a sampling frequency of 48 kHz (44.1 kHz for audio CDs).

320_UXJCA_EN.book 49

Language Code Table and Country/Area Code Table

Language Code Table

Language name, language code, input code Abkhazian, ab/abk, 0102 Afar, aa/aar, 0101 Afrikaans, af/afr, 0106 Albanian, sq/sqi, 1917 Amharic, am/amh, 0113 Arabic, ar/ara, 0118 Armenian, hy/hye, 0825 Assamese, as/asm, 0119 Aymara, ay/aym, 0125 Azerbaijani, az/aze, 0126 Bashkir, ba/bak, 0201 Basque, eu/eus, 0521 Belarusian, be/bel, 0205 Bengali, bn/ben, 0214 Bihari, bh/bih, 0208 Bislama, bi/bis, 0209 Breton, br/bre, 0218 Bulgarian, bg/bul, 0207 Burmese, my/mya, 1325 Catalan, ca/cat, 0301 Central Khmer, km/khm, 1113 Chinese, zh/zho, 2608 Corsican, co/cos, 0315 Croatian, hr/hrv, 0818 Czech, cs/ces, 0319 Danish, da/dan, 0401 Dutch, nl/nld, 1412 Dzongkha, dz/dzo, 0426 English, en/eng, 0514 Esperanto, eo/epo, 0515 Estonian, et/est, 0520 Finnish, fi/fin, 0609 Fijian, fj/fij, 0610 Faroese, fo/fao, 0615 French, fr/fra, 0618 Galician, gl/glg, 0712 Georgian, ka/kat, 1101 German, de/deu, 0405 Greek, el/ell, 0512 Guarani, gn/grn, 0714 Gujarati, gu/guj, 0721 Hausa, ha/hau, 0801 Hebrew, iw/heb, 0923 Hindi, hi/hin, 0809 Hungarian, hu/hun, 0821 Icelandic, is/isl, 0919 Indonesian, in/ind, 0914 Interlingua, ia/ina, 0901 Interlingue, ie/ile, 0905 Inupiaq, ik/ipk, 0911 Irish, ga/gle, 0701 Italian, it/ita, 0920 Japanese, ja/jpn, 1001 Javanese, jw/jav, 1023 Kalaallisut, kl/kal, 1112 Kannada, kn/kan, 1114 Kashmiri, ks/kas, 1119 Kazakh, kk/kaz, 1111 Kinyarwanda, rw/kin, 1823 Kirghiz, ky/kir, 1125 Korean, ko/kor, 1115 Kurdish, ku/kur, 1121 Lao, lo/lao, 1215 Latin, la/lat, 1201 Latvian, lv/lav, 1222 Lingala, ln/lin, 1214 Lithuanian, lt/lit, 1220 Macedonian, mk/mkd, 1311 Malagasy, mg/mlg, 1307 Malay, ms/msa, 1319 Malayalam, ml/mal, 1312 Maltese, mt/mlt, 1320 Maori, mi/mri, 1309 Marathi, mr/mar, 1318 Mongolian, mn/mon, 1314 Moldavian, mo/mol, 1315 Nauru, na/nau, 1401 Nepali, ne/nep, 1405 Norwegian, no/nor, 1415 Occitan, oc/oci, 1503 Oriya, or/ori, 1518 Oromo, om/orm, 1513 Panjabi, pa/pan, 1601 Persian, fa/fas, 0601 Polish, pl/pol, 1612 Portuguese, pt/por, 1620 Pushto, ps/pus, 1619 Quechua, qu/que, 1721 Romanian, ro/ron, 1815 Romansch, rm/roh, 1813 Rundi, rn/run, 1814 Russian, ru/rus, 1821 Samoan, sm/smo, 1913 Sango, sg/sag, 1907 Sanskrit, sa/san, 1901 Scottish Gaelic, gd/gla, 0704 Serbian, sr/srp, 1918 Serbo-Croatian, sh/---, 1908 Shona, sn/sna, 1914 Sindhi, sd/snd, 1904 Sinhalese, si/sin, 1909 Slovak, sk/slk, 1911 Slovenian, sl/slv, 1912 Somali, so/som, 1915 Sotho, Southern, st/sot, 1920 Spanish, es/spa, 0519 Sundanese, su/sun, 1921 Swahili, sw/swa, 1923 Swati, ss/ssw, 1919 Swedish, sv/swe, 1922 Tagalog, tl/tgl, 2012 Tajik, tg/tgk, 2007 Tamil, ta/tam, 2001 Tatar, tt/tat, 2020 Telugu, te/tel, 2005 Thai, th/tha, 2008 Tibetan, bo/bod, 0215 Tigrinya, ti/tir, 2009 Tonga (Tonga Islands), to/ton, 2015 Tsonga, ts/tso, 2019 Tswana, tn/tsn, 2014 Turkmen, tk/tuk, 2011 Turkish, tr/tur, 2018 Twi, tw/twi, 2023 Ukrainian, uk/ukr, 2111 Urdu, ur/urd, 2118 Uzbek, uz/uzb, 2126 Vietnamese, vi/vie, 2209 Volapk, vo/vol, 2215 Welsh, cy/cym, 0325 Western Frisian, fy/fry, 0625 Wolof, wo/wol, 2315 Xhosa, xh/xho, 2408 Yiddish, ji/yid, 1009 Yoruba, yo/yor, 2515 Zulu, zu/zul, 2621

arent implemented yet. For legal reasons, we are not distributing code for the arithmetic-coding variants of JPEG; see LEGAL ISSUES. We have made no provision for supporting the hierarchical or lossless processes defined in the standard. We provide a set of library routines for reading and writing JPEG image files, plus two sample applications cjpeg and djpeg, which use the library to perform conversion between JPEG and some other popular image file formats. The library is intended to be reused in other applications. In order to support file conversion and viewing software, we have included considerable functionality beyond the bare JPEG coding/decoding capability; for example, the color quantization modules are not strictly part of JPEG decoding, but they are essential for output to colormapped file formats or colormapped displays. These extra functions can be compiled out of the library if not required for a particular application. We have also included jpegtran, a utility for lossless transcoding between different JPEG processes, and rdjpgcom and wrjpgcom, two simple applications for inserting and extracting textual comments in JFIF files. The emphasis in designing this software has been on achieving portability and flexibility, while also making it fast enough to be useful. In particular, the software is not intended to be read as a tutorial on JPEG. (See the REFERENCES section for introductory material.) Rather, it is intended to be reliable, portable, industrial-strength code. We do not claim to have achieved that goal in every aspect of the software, but we strive for it. We welcome the use of this software as a component of commercial products. No royalty is required, but we do ask for an acknowledgement in product documentation, as described under LEGAL ISSUES. LEGAL ISSUES In plain English: 1. We dont promise that this software works. (But if you find any bugs, please let us know!) 2. You can use this software for whatever you want. You dont have to pay us. 3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that youve used the IJG code. In legalese: The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided AS IS, and you, its user, assume the entire risk as to its quality and accuracy. This software is copyright 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below. Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions: (1)If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation. (2)If only executable code is distributed, then the accompanying documentation must state that this software is based in part on the work of the Independent JPEG Group. (3)Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind. These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us. Permission is NOT granted for the use of any IJG authors name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as the Independent JPEG Groups software. We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor. ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.) However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does not limit you more than the foregoing paragraphs do. The Unix configuration script configure was produced with GNU Autoconf. It is copyright by the Free Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable.

text version at ftp://ftp.uu.net/graphics/jpeg/jfif.txt.gz, but it is missing the figures. The TIFF 6.0 file format specification can be obtained by FTP from ftp://ftp.sgi.com/graphics/tiff/TIFF6.ps.gz. The JPEG incorporation scheme found in the TIFF 6.0 spec of 3-June92 has a number of serious problems. IJG does not recommend use of the TIFF 6.0 design (TIFF Compression tag 6). Instead, we recommend the JPEG design proposed by TIFF Technical Note #2 (Compression tag 7). Copies of this Note can be obtained from ftp.sgi.com or from ftp:// ftp.uu.net/graphics/jpeg/. It is expected that the next revision of the TIFF spec will replace the 6.0 JPEG design with the Notes design. Although IJGs own code does not support TIFF/JPEG, the free libtiff library uses our library to implement TIFF/JPEG per the Note. libtiff is available from ftp://ftp.sgi.com/graphics/tiff/. ARCHIVE LOCATIONS The official archive site for this software is ftp.uu.net (Internet address 192.48.96.9). The most recent released version can always be found there in directory graphics/ jpeg. This particular version will be archived as ftp:// ftp.uu.net/graphics/jpeg/jpegsrc.v6b.tar.gz. If you dont have direct Internet access, UUNETs archives are also available via UUCP; contact help@uunet.uu.net for information on retrieving files that way. Numerous Internet sites maintain copies of the UUNET files. However, only ftp.uu.net is guaranteed to have the latest official version. You can also obtain this software in DOS-compatible zip archive format from the SimTel archives (ftp:// ftp.simtel.net/pub/simtelnet/msdos/graphics/), or on CompuServe in the Graphics Support forum (GO CIS:GRAPHSUP), library 12 JPEG Tools. Again, these versions may sometimes lag behind the ftp.uu.net release. The JPEG FAQ (Frequently Asked Questions) article is a useful source of general information about JPEG. It is updated constantly and therefore is not included in this distribution. The FAQ is posted every two weeks to Usenet newsgroups comp.graphics.misc, news.answers, and other groups. It is available on the World Wide Web at http:/ /www.faqs.org/faqs/jpeg-faq/ and other news.answers archive sites, including the official news.answers archive at rtfm.mit.edu: ftp://rtfm.mit.edu/pub/usenet/news.answers/ jpeg-faq/. If you dont have Web or FTP access, send e-mail to mail-server@rtfm.mit.edu with body send usenet/news.answers/jpeg-faq/part1 send usenet/news.answers/jpeg-faq/part2 RELATED SOFTWARE Numerous viewing and image manipulation programs now support JPEG. (Quite a few of them use this library to do so.) The JPEG FAQ described above lists some of the more popular free and shareware viewers, and tells where to obtain them on Internet. If you are on a Unix machine, we highly recommend Jef Poskanzers free PBMPLUS software, which provides many useful operations on PPM-format image files. In particular, it can convert PPM images to and from a wide range of other formats, thus making cjpeg/djpeg considerably more useful. The latest version is distributed by the NetPBM group, and is available from numerous sites, notably ftp:// wuarchive.wustl.edu/graphics/graphics/packages/ NetPBM/. Unfortunately PBMPLUS/NETPBM is not nearly as portable as the IJG software is; you are likely to have difficulty making it work on any non-Unix machine. A different free JPEG implementation, written by the PVRG group at Stanford, is available from ftp:// havefun.stanford.edu/pub/jpeg/. This program is designed for research and experimentation rather than production use; it is slower, harder to use, and less portable than the IJG code, but it is easier to read and modify. Also, the PVRG code supports lossless JPEG, which we do not. (On the other hand, it doesnt do progressive JPEG.) FILE FORMAT WARS Some JPEG programs produce files that are not compatible with our library. The root of the problem is that the ISO JPEG committee failed to specify a concrete file format. Some vendors filled in the blanks on their own, creating proprietary formats that no one else could read. (For example, none of the early commercial JPEG implementations for the Macintosh were able to exchange compressed files.) The file format we have adopted is called JFIF (see REFERENCES). This format has been agreed to by a number of major commercial JPEG vendors, and it has become the de facto standard. JFIF is a minimal or low end representation. We recommend the use of TIFF/JPEG (TIFF revision 6.0 as modified by TIFF Technical Note #2) for high end applications that need to record a lot of additional data about an image. TIFF/JPEG is fairly new and not yet widely supported, unfortunately. The upcoming JPEG Part 3 standard defines a file format called SPIFF. SPIFF is interoperable with JFIF, in the sense that most JFIF decoders should be able to read the most common variant of SPIFF. SPIFF has some technical advantages over JFIF, but its major claim to fame is simply that it is an official standard rather than an informal one. At

Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1. You may copy and distribute verbatim copies of the Librarys complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

[Notice on GNU General Public License]
This product include the software licensed for use under the terms of a GNU General Public License. A copy of the corresponding source code can be obtained by being charged the fee for distribution. To obtain a copy, contact your local Pioneer Customer Support Center. See the GNU website (http://www.gnu.org) for details of the GNU General Public License.

320_UXJCA_EN.book 56

Cautions on use

Moving the player

If you need to move this unit, first remove the disc if theres one loaded, and close the disc tray. Next, press STANDBY/ON to switch the power to standby, checking that the POWER OFF indication on the front panel display goes off. Wait at least 10 seconds. Lastly, disconnect the power cord. Never lift or move the unit during playback discs rotate at a high speed and may be damaged.

Condensation

If the player is moved suddenly from a cold place into a warm room (in winter, for example) or if the temperature in the room in which the player is installed rises suddenly due to a heater, etc., water droplets (condensation) may form inside (on operating parts and the lens). When condensation is present, the player will not operate properly and playback is not possible. Let the player stand at room temperature for 1 or 2 hours with the power turned on (the time depends on the extent of condensation). The water droplets will dissipate and playback will become possible. Condensation can also occur in the summer if the player is exposed to the direct wind from an air-conditioner. If this happens, move the player to a different place.

Place of installation

Select a stable place near the TV and AV system to which the unit is connected. Do not place the player on top of a TV or color monitor. Keep it away from cassette decks or other components easily affected by magnetism. Avoid the following types of places: Places exposed to direct sunlight Humid or poorly ventilated places Extremely hot or cold places Places subject to vibration Dusty places Places exposed to soot, steam or heat (in kitchens, etc.)

Cleaning the player

Normally, wipe the player with a soft cloth. For tough dirt, apply some neutral detergent diluted in 5 to 6 parts water to a soft cloth, wring out thoroughly, wipe off the dirt, then wipe again with a dry cloth. Note that getting alcohol, thinner, benzene or insecticide on the player could cause the print and coating to peel off. Also, avoid leaving rubber or vinyl products in contact with the player for long periods of time, as this could damage the cabinet. When using chemical-impregnated wipes, etc., read the wipes cautions carefully. Unplug the power cord from the power outlet when cleaning the player.

Set Hybrid Disc Playback to CD (page 41).
To play the BDMV format on BD-R/-RE discs containing both BDMV and BDAV formats, set BDMV/BDAV Playback Priority to BDMV (page 41).

320_UXJCA_EN.book 61

KURO LINK
Problem KURO LINK function does not work. Check Is the HDMI cable properly connected? Is the HDMI cable you are using a High Speed HDMI cable? Are you connected to the TV using an HDMI cable to watch the picture? Is KURO LINK set to On on the player? Does the connected device support the KURO LINK function? Remedy To use the KURO LINK function, connect the Flat Panel TV and AV system (AV receiver or amplifier, etc.) to the HDMI OUT terminal (page 16). Use a High Speed HDMI cable. The KURO LINK function may not work properly if HDMI cable other than a High Speed HDMI cable is used. If video signals are being output from a terminal other than the HDMI OUT terminal, the KURO LINK function does not work. Connect to the TV using an HDMI cable and press VIDEO SELECT to switch to the HDMI OUT terminal (pages 16 and 22). Set KURO LINK to On on the player (page 39). The KURO LINK function will not work with devices of other brands that do not support the KURO LINK function, even when connected using an HDMI cable. The KURO LINK function will not work if devices that do not support the KURO LINK function are connected between the KURO LINKcompatible device and the player. See About connections to components of other makes supporting the KURO LINK function on page 16. Even when connected to a Pioneer product compatible with the KURO LINK function, some of the functions may not work. Also refer to the operating instructions of the connected device. Set KURO LINK to On on the connected device. The KURO LINK function operates when KURO LINK is set to On for all devices connected to the HDMI OUT terminal. Once connections and settings of all the devices are finished, be sure to check that the players picture is output to the Flat Panel TV. (Also check after changing the connected devices and connecting and/or disconnecting HDMI cables.) If the players picture is not being output to the Flat Panel TV, the KURO LINK function may not work properly. For details, refer to the operating instructions of the connected device. The KURO LINK function may not work if three or more players, including this player, are connected by HDMI cable. Set Display Power On to On (page 39).
Is KURO LINK set to On on the connected device?

Others

Problem The players power turns off automatically. Check Is Auto Power Off set to On? Is Display Power Off set to On? Remedy If Auto Power Off is set to On, the players power turns off automatically if no operation is performed for over 30 minutes (page 41). The players power may turn off together with the power of the TV connected to the HDMI OUT terminal. If you do not want the players power to turn off when the TVs power is turned off, set Display Power Off to Off (page 39). The players power may turn on together with the power of the TV connected to the HDMI OUT terminal. If you do not want the players power to turn on when the TVs power is turned on, set KURO LINK to Off (page 39).
The players power turns on automatically.

Is KURO LINK set to On?

Player cannot be operated with remote control.
Is an AV receiver or amplifier Operate with the remote control of the device connected to the connected to the CONTROL CONTROL IN terminal. IN terminal on the players rear panel? Are you operating the remote Operate from within 23 feet (7 m) of the remote control sensor. control from a point too far away from the player? Are the batteries dead? Replace the batteries (page 7). The input of the TV and AV system (AV receiver or amplifier, etc.) connected to the HDMI OUT terminal may automatically switch to the player when playback starts on the player or the menu screen (Home Media Gallery, etc.) is displayed. If you do not want the inputs of the connected TV and AV system (AV receiver or amplifier, etc.) to switch automatically, set KURO LINK to Off (page 39). If the message appears repeatedly, please ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Input of connected TV and AV Is KURO LINK set to On? system switches automatically.
Processing failed. is displayed.

320_UXJCA_EN.book 63

Remedy Always press STANDBY/ON on the players front panel or STANDBY/ON on the remote control and check that POWER OFF has turned off from the players front panel display before disconnecting the power cord. Be particularly careful when the power cord is connected to the AC outlet on another device because the player turns off in conjunction with the device. Turn the players power off, then turn the power back on. Turn the players power off, then reconnect the external storage device (page 17). Use a USB cable with a length of 2 meters or less. Turn the players power off, then turn the external hard disks power on.
Settings you have made have Have you disconnected the been cleared. power cord while the players power was on? Has there been a power failure? EXT does not light on the Is the external storage device players front panel display properly connected? when a USB (external storage) device is connected. Are you using a USB cable that is longer than 2 meters? Is the power of the external hard disk turned on?

Is the external storage device External storage device may not work if connected to the USB port via connected to the USB port via a memory card reader or USB hub. a memory card reader or USB hub? Does the external storage device contain multiple partitions? External storage devices may not be recognized if they contain multiple partitions. Some external storage devices may not operate. EXT flashes on the players Is the external storage device front panel display when a write-protected? USB (external storage) device Is the external storage is connected. devices file system FAT16 or FAT32? Turn the players power off, then disable the write-protection. Only external storage devices with a FAT16 or FAT32 file system can be used. They may be usable if they are formatted from the player (page 44). Turn the players power off, then turn the power back on.

Glossary

Angle (Multi angle)
Up to 9 camera angles can be recorded simultaneously on BDROM or DVD-Video discs, letting you view the same scene from different angles.

Component video output

This video output terminal provides clearer pictures when connected to a TV equipped with component inputs. Component video signals consist of three signals, Y, PB and PR.

Deep Color

See About HDMI on page 14.
AVCHD (Advanced Video Codec High Definition)
See Playing DVDs on page 10.

Default Gateway

A default gateway is a communication device such as a router which passes data between networks. It is used to direct data to networks on which the destination gateway is not explicitly specified.
Of the BD format, the Audio Visual Format Specifications for HD digital broadcast recording is referred to as BDAV on this player and in this operating instructions.
DHCP (Dynamic Host Configuration Protocol)
This protocol provides configuration parameters (IP address, etc.) for computers and other devices connected to the network.
See Playing BDs on page 9.

DNS (Domain Name System)

This is a system for associating Internet host names with IP addresses.

BD-LIVE

Of the BD format, the Audio Visual Format Specifications designed for pre-packaged high definition (HD) movie contents is referred to as BDMV on this player and in this operating instructions.

Dolby Digital

Dolby Digital is an audio format to record the sound in up to 5.1 channels with a fraction of the amount of data as compared to linear PCM audio signals.

Dolby Digital Plus

Dolby Digital Plus is an audio format for high-definition media. Built on Dolby Digital, it combines the efficiency and flexibility to provide high quality multi-channel audio. With BD-ROMs, up to 7.1 channels of digital sound can be recorded.

BONUSVIEW

320_UXJCA_EN.book 64

Dolby TrueHD

Dolby TrueHD is an audio format using lossless coding. With BDROMs, up to 8 channels can be recorded at 96 kHz/24 bits, or up to 6 channels at 192 kHz/24 bits.
MPEG (Moving Picture Experts Group)
The name of a family of standards used to encode video and audio signals in a digital compressed format. The video encoding standards include MPEG-1 Video, MPEG-2 Video, MPEG-4 Visual, MPEG-4 AVC, etc. The audio encoding standards include MPEG1 Audio, MPEG-2 Audio, MPEG-2 AAC, etc.
A technology for protecting copyrighted digital data. Digitized videos, images and audio retain the same quality even when they are copied or transferred repeatedly. DRM is a technology for restricting the distribution or playback of such digital data without the authorization of the copyright holder.

Parental Lock

See Changing the Parental Lock level for viewing DVDs and Changing the Age Restriction for viewing BD-ROMs on page 45.

DTS Digital Surround

DTS Digital Surround is an audio format to record 48 kHz/24 bits audio signals in 5.1 channels.
Picture-in-Picture (P-in-P)
This is a function for superimposing a sub video on the main video. Some BD-ROMs include secondary video, which can be superimposed on the primary video.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is an audio format using lossy coding. It can record 7.1 channels at 96 kHz/24 bits.

Port number

This is a sub-address provided below the IP address for simultaneously connecting to multiple parties during Internet communications.

DTS-HD Master Audio

DTS-HD Master Audio is an audio format using lossless coding. With BD-ROMs, 7.1 channels can be recorded at 96 kHz/24 bits, or 5.1 channels at 192 kHz/24 bits.

BDP-320
Pioneer BD-Live Blu-ray Disc Player featuring 48-bit Deep Color and 7.1-ch Analog Outputs

PERFORMANCE FEATURES

Spectacular 1080p Picture Quality: The BDP-320 provides up to 1920
BD-Live Compliant (Profile 2.0): Enjoy special disc contents in
x 1080p resolution for unrivaled picture quality. And with True 24fps, now see your movies as the director intended.
Deep Color: The BDP-320 supports 48-bit* Deep Color, offering high
Picture-in-Picture form, and also download additional content from the internet to the built-in 1GB memory, such as the directors interview and languages not contained on the disc.**
USB Input for BD-LIVE Contents Storage 7.1 Channel Analog Audio Outputs: For compatibility with non HDMI
definition images with superb color detail.
x.v.Color: An advanced feature which greatly broadens the color
equipped receivers and preamps.
Internal Audio Decoders: The BDP-320 features internal decoding
space input to include 1.8 times as many natural colors than standard RGB signals.
HDMI Precision Quartz Lock System (PQLS) Jitterless Transmission
of all advanced audio formats including Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution, and DTS-HD Master Audio.
Easy Operation and Setup: New Advanced HD GUIs for easy
(2-ch): By HDMI connection with a compatible Pioneer A/V receiver, CD music is precisely reproduced with minimum jitter.
KURO LINK: By connecting the BDP-320 to a Pioneer KURO flat

navigation.

Latest Generation PureCinema Progressive Scan Multi-Format Compatibility: You can play high definition DVD discs
panel TV or monitor and a compatible Pioneer A/V receiver, KURO LINK lets you operate the entire systems basic functions such as power on/off and playback through KUROs remote control. The new KURO LINK Video Adjustment System automatically switches to optimal video settings adjusted by unique parameters developed by Pioneer KURO and Blu-ray Disc player engineers.
Picture Control Suite: 13 different video adjustments (Progressive
recorded by digital video cameras in AVCHD format. You can also play BD-R/RE, DVD-R/RW, etc. recorded using Blu-ray Disc recorders or DVD recorders as well as CD/CD-R. * Except for and 1080p/60 output. ** D-Live only available on compatible discs and playable features B depend on the disc contents.
Motion, PureCinema, YNR, CNR, BNR, MNR, Detail, White Level, Black Level, Black Setup, Gamma Correction, Hue, and Chroma Level)
Triple High-Definition NR: Component Frame NR lowers Gaussian noise without blurring the

picture.

Block NR minimizes block noise (mosaic-like artifacts). Mosquito NR reduces the fluttery noise around the edges of

objects.

TERMINALS
HDMI Output Component Video Output Composite Video Output 7.1-Channel Audio Output Optical Digital Output SR Input Ethernet USB Input

INTEGRATED TECHNOLOGIES

SPECIFICATIONS
Power Requirements: 120 V 60 Hz Product Weight: 7 lbs. 11 oz. (3.5 kg)

PRODUCT DIMENSIONS

W x H x D: 16-9/16 x 2-15/16 x 11 inches (420 x 83 x 287 mm)

CONNECTIONS

Specifications and design subject to modification without notice. PIONEER and the Pioneer logo is a registered trademark of Pioneer Corporation. Compatible with MPEG1 Audio LayerkHz, 44.1 kHz and 48 kHz formats. MP3 file name requires mp3 as an extension. Chinese characters cannot be displayed, although files featuring them can be played. 9999 tracks/999 folders can be played per disc. Can play VBR (Variable Bit Rate) content, but playing time may not be shown correctly. This unit may not be able to play back discs that have been recorded on other units due to the recording conditions, mode, surface dirt, or scratches. Blu-ray Disc and the Blu-ray Disc logo are trademarks of Blu-ray Disc Association. The DVD logo is a registered trademark of DVD Format/Logo Licensing Corporation. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

x.v.Color and the x.v.Color logo are trademarks of Sony Corporation. x.v.Color only available for playback of discs recorded with AVCHD devices. BD-LIVE logo is trademark of Blu-ray Disc Association. BONUSVIEW logo is trademark of Blu-ray Disc Association. AVCHD and the AVCHD logo are trademarks of Panasonic Corporation and Sony Corporation. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. DTS is a registered trademark & the DTS logo and Symbol are trademarks of DTS, Inc.
2009 Pioneer Electronics (USA) Inc.