Digital Parking Assistance Camera
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Information to User Alteration or modifications carried out without appropriate authorization may invalidate the users right to operate the equipment. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
Cmara digital de auxilio de estacionamiento
Owners Manual Manual del Propietario

ENGLISH ESPAOL

ND-BC20PA

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC. PIONEER EUROPE NV
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

WARNING:

PIONEER ELECTRONICS ASIACENTRE PTE. LTD. PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300
Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Connection to a TV with an RCA video input is possible, but confirm whether the TV you use has a reverse gear connection function. Direct sunlight or strong light (sunlight reflected from a bumper etc) on the camera may result in smear above and below the location where the light strikes, but this is not a malfunction. This product is designed to supplement the drivers rear view, but the camera images do not show all dangers and obstacles. Be sure to look behind you when reversing to confirm the view. Since this product uses a wide-angle lens, objects nearby appear wider and objects far away appear narrower, and distance may seem different than the actual distance. Always make sure to visually check behind your car when backing up. This product is required to be set individually for each type of vehicle. When reinstalling this product on a different car such as after purchasing a different car, always make sure to change the settings prior to use. Always drive carefully without relying too much on this product. Check camera stand installation before driving. Are the screws loose? Is the camera stand firmly secured? If the rear view camera comes loose while you are driving it may cause an accident. This device is designed for use ONLY with Pioneer unit with rear camera input. Before continuing setup, please confirm you are using the Reverse mode to view this screen. Those Pioneer models compatible with the screen display (guide, menu, etc.) of this product are as listed below. When combining with other products, the screen display displayed by the combined product may be superimposed on the screen display displayed by this product. AVIC-Z1 / AVIC-Z2 / AVIC-HD1BT / AVIC-HD3 / AVIC-D3 / AVH-P5900DVD / AVH-P5950DVD / AVH-P7900DVD / AVH-P7950DVD

What's What

Button Unit
Preparations Before Beginning Setup
The setup procedure for this product consists of taking photographs of images of the rear view camera when viewed from the location where the rear view camera is installed, and then setting up the camera based on those photographs after moving the vehicle to a safe location provided with tire blocks. Move the vehicle to the location where photographs are to be taken before beginning the setup procedure.

First Time Setup

An initial setup is required when using this product for the first time. Begin the setup procedure after parking the vehicle at the location where photographs are to be taken by referring to the section on Preparations Before Beginning Setup.

Taking Photographs

A photograph to be used for setup is taken. (Refer to First Time Setup and Changing Basic Settings or Other Settings for information to get started with photographing procedure.)
1. Put the car in reverse.
Note: When performing setup, always make sure to set the parking brake and step on the brake to make sure the car is stopped.
1. Press the ENTER button twice. 2. Press the ENTER button again.
A photograph of the image of rear view camera is taken.
3. Press the ENTER button.
Press the ENTER button if the photograph taken is satisfactory. Press the MODE button to retake the photograph.

MODE Button

This is used when changing the screen display mode. This is also used to return to the previous screen or discontinue an operation on the setup screen.

1. Park the vehicle.

Park the vehicle in the center of the parking space indicated with the white lines.
2. Simultaneously press the ENTER and + buttons on the button unit. 3. Press the ENTER button four times. 4. Take the photograph.
Take the photograph to be used for setup. Take the photograph while referring to the section on Taking Photographs.
4. Press the ENTER button twice. 5. Move the car to a safe location provided with tire blocks.
Move the car from the location where the photograph was taken to a location provided with tire blocks.
Note: Always make sure that the car has come to a complete stop and parked after moving. Do not turn off the engine. Photograph data will be deleted if the engine is turned off.

+ Button

This is used when selecting an item on the setup screen or when adjusting position or angle.
5. Set the basic settings.
Set the basic settings in the order of items A to F of Basic Settings based on the photograph taken. Make the settings by referring to Basic Settings. White lines Center of parking space

Button

ENTER Button
This is used to finalize a display or item on the setup screen.
6. Select OK and press the ENTER button.
The initial setup is completed and the settings are stored in memory.
Note: Please make sure to read the caution and then press the ENTER button to go to the next step. Photograph data is deleted when setup is ended. This camera and associated electronic guides are intended solely as a driving aid. This unit is not a substitute for you attentiveness, judgement, and care while driving, moving, or parking your vehicle. Always observe safe driving rules and driving laws, even if they contradict the unit instructions.
6. Press the ENTER button. 7. Press the ENTER button.
When performing this procedure starting from First Time Setup, proceed to step 5 of First Time Setup. When performing this procedure starting from Changing Basic Settings or Other Settings, proceed to step 5 of Changing Basic Settings or Other Settings.
2. Move the vehicle forward.
Move the vehicle forward from the location where it has been parked to the location where the photographs are to be taken.
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901 Blvd. Manuel Avila Camacho piso Col. Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

IMPORTANT SAFEGUARDS

Do not wash your car with an automatic car wash or high-pressure water as it may result in water entering the camera or the camera falling off. Do not attempt to heat the surface of the camera lens or camera lens itself with a lighter and so on when they have become frozen. This can cause a malfunction. This product is a rear view camera for checking the view at the rear of a car. A rear view camera is a camera that provides symmetrical images in the same way as rear and side view mirrors.

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Published by Pioneer Corporation. Copyright 2007 by Pioneer Corporation. All rights reserved. Publicado por Pioneer Corporation. Copyright 2007 Pioneer Corporation. Todos los derechos reservados. Printed in Japan Impreso en Japn
Take photographs at the location where the white lines cross the dotted lines while referring to the photograph above.
Note: Perform setup at a parking space having white lines and tire blocks. The setup will not be correct if the vehicle is not located in the center of the parking space.
<KKNNX> <07D00000>

<CZR5083-A> E

Basic Settings
Basic settings refer to those settings that are mandatory. Basic settings are set during initial setup. These settings can be changed later.
Adjust the angle so that an object (such as the tire blocks) serving as a reference along the horizontal lines is displayed.
When performing this procedure starting from First Time Setup, proceed to section D entitled View Diagonal. When performing this procedure starting from Changing Basic Settings or Other Settings, return to step 5 of Changing Basic Settings or Other Settings.

E. View Angle

Adjust the view angle (high angle mode) as viewed from directly overhead.
F. Vertical Guideline (Width)
Adjust the width within the vertical guidelines.
Changing Basic Settings or Other Settings
Basic settings set during initial setup can be changed. In addition, other settings can also be made such as View (Wide/Zoom) and Guideline (Shape) on Advanced Settings. Begin the setup procedure after parking the vehicle at the location where photographs are to be taken by referring to the section on Preparations Before Beginning Setup.

Advanced Settings

Advanced settings such as View (Wide/Zoom) and Guideline (Shape) can be set using advanced settings.

C. Guideline (Distance)

The distance between the horizontal guidelines can be adjusted. The horizontal guidelines are displayed at the interval shown in Fig. 2 during the initial setup when the camera has been installed at the position shown in Fig. 1.
Fig. 2 Fig. 1 Approx. 2 m / 7 ft. Approx. 1 m / 3 ft. Approx. 1 m / 3 ft.

A. Centerline

Adjust the monitor connected to the rear view camera. Adjust so that the vehicle centerline is displayed in the center of the screen.

Note: The centerline serves as a reference for vehicle width when parked (orange line).
1. Press the ENTER button. 2. Adjust the angle with the + and buttons.
Adjust the angle so that the white lines are aligned with the vertical lines.
1. Press the ENTER button. 2. Adjust the position with the + and buttons.
Adjust the position using the white lines of the parking space as a reference.

A. View (Wide/Zoom)

This adjustment is only necessary when only ground is displayed or when the display is too small or illegible when viewed with the high angle mode because of the height of the rear view camera.

D. View Diagonal

Adjust the inclination of the rear view camera image as viewed from the location where the rear view camera is installed. Horizontal lines
Note: Adjustment can be made within the range of 511 to +511. Some portions may not be able to be seen depending on the settings.
1. Put the vehicle in reverse.
1. Press the ENTER button. 2. Adjust so that the centerline is in the center of the screen using the + and buttons.
Adjust so that the number of lines is the same on both sides of the screen.
1. Press the ENTER button. 2. Adjust view diagonal with the + and buttons.
Adjust view diagonal so that the white lines of the parking space are displayed symmetrically. Vertical guidelines Vertical lines
Note: Adjustment can be made within the range of 511 to +511. Note: Adjustment can be made within the range of 255 to +255.
1. Press the ENTER button. 2. Adjust the view elevation with the + and buttons.
Note: Adjustment can be made within the range of 63 to +63.

50 1.5 m / 5 ft.

When performing this procedure starting from First Time Setup, proceed to section C entitled Position (Horizontal). When performing this procedure starting from Changing Basic Settings or Other Settings, return to step 5 of Changing Basic Settings or Other Settings.
2. Simultaneously press the ENTER and + buttons. 3. Press the ENTER button four times. 4. Take the photograph.
Return to step 5 of Changing Basic Settings or Other Settings.

When performing this procedure starting from First Time Setup, proceed to section F entitled Vertical Guideline (Width). When performing this procedure starting from Changing Basic Settings or Other Settings, return to step 5 of Changing Basic Settings or Other Settings.
3. Press the ENTER button. 4. Press the ENTER button twice.
When performing this procedure starting from First Time Setup, proceed to step 6 of First Time Setup. When performing this procedure starting from Changing Basic Settings or Other Settings, return to step 5 of Changing Basic Settings or Other Settings.

B. Guideline (Shape)

Adjust the inclination of the vehicle vertical guidelines (shape) when there is a considerable discrepancy with the vehicle width towards the back of the field of view.
Note: The horizontal guidelines consist of three reference lines that serve as a reference when parking (green, yellow and red lines). In the case the view angle of the basic settings has been adjusted from the factory adjustment, the distances between the horizontal guidelines as shown in Fig. 2 (approx. 1 m, 1 m and 2 m) will be different.

C. Position (Horizontal)

5. Select the parameter to be set with the + and buttons and then press the ENTER button.
Adjust the horizontal of the rear view camera image as viewed from the location where the rear view camera is installed.

Centerline

Note: Adjustment can be made within the range of 255 to +255.
When performing this procedure starting from First Time Setup, proceed to section B entitled Position (Rotate). When performing this procedure starting from Changing Basic Settings or Other Settings, return to step 5 of Changing Basic Settings or Other Settings.
1. Press the ENTER button. 2. Adjust the horizontal position with the + and buttons.
Adjust so that the center of the parking space is displayed in the center of the camera screen in the horizontal direction.
When performing this procedure starting from First Time Setup, proceed to section E entitled View Angle. When performing this procedure starting from Changing Basic Settings or Other Settings, return to step 5 of Changing Basic Settings or Other Settings.

B. Position (Rotate)

Adjust the rotation of the rear view camera image as viewed from the location where the rear view camera is installed.
Basic Settings Set the basic settings while referring to Basic Settings.
Advanced Settings Set the advanced settings while referring to Advanced Settings.

Horizontal guidelines

The settings are stored in memory.

Vertical guidelines

Note: Adjustment can be made within the range of 127 to +127.
Horizontal direction centerline
Note: The vertical guidelines (shape) setting reflect the screen display of view angle and vertical guideline (width).

D. Guideline (On/Off)

This is used to switch the vertical and horizontal guidelines on and off.
Returning to Default Settings
The product can be reset to the default settings. Reset to default settings in the following situations:
The position of the camera has changed. The vehicle on which the camera is installed has changed.
Changing the Screen Display Mode
1. Press the MODE button when the rear view camera image is displayed.
The screen display mode changes in the manner described below each time the MODE button is pressed. Normal angle mode High angle mode
Note: The screen display mode returns to the normal angle mode prior to being changed when the engine is turned off.
1. Press the ENTER button. 2. Select on or off for the guidelines with the + and buttons. 3. Press the ENTER button. 4. Press the ENTER button twice.
3) Cut one strip of masking tape, approximately 15 feet (4.5 meter) in length, and place on the parking surface from the center of the rear bumper extending back. This strip will indicate the centerline of the vehicle and will be used in both the Basic Settings and Advanced Settings.

Step 2

Discrepancies Between Screen Display and Actual Road Surface
Discrepancies in distance and the course over which the vehicle is traveling may occur between the horizontal guidelines on the screen and actual road surface in the following situations.
When there is a steep downgrade behind the vehicle:
When there is a steep downgrade behind the vehicle, the horizontal guidelines appear farther to the rear than the actual distances. When there is an obstacle present on a steep downgrade, the obstacle appears to be closer than it actually is. Similarly, discrepancies also occur in the course over which the vehicle is traveling between the horizontal guidelines and the actual road surface.

Specifications

Common Units Power source.. Grounding system.. Max. current consumption. Output image... Video output... DC 14.4 V (allowable range: 10.8 V to 15.1 V) Negative ground type Approx. 250 mA Mirror image (for rear view confirmation) 1 Vp-p (75 )
1. Press the MODE and ENTER buttons simultaneously.

Note: Press the MODE button to cancel resetting to default settings.
When there is a steep upgrade behind the vehicle:
The horizontal guidelines serve as a reference for distance relative to a flat road surface. Consequently, when there is a steep upgrade behind the vehicle, the horizontal guidelines appear closer to you than the actual distances. For example, in the case of an obstacle present on a steep upgrade, the obstacle appears to be farther away than it actually is. Similarly, discrepancies also occur in the course over which the vehicle is traveling between the horizontal guidelines and the actual road surface.
2. Press the ENTER button.
All of the settings are returned to the default settings.
Optional Advanced Setup Preparation
To improve accuracy, the optional setup will use a grid of masking tape to provide a visual representation similar to the on-screen setting of the system. To complete this procedure, you will need approximately 54 feet (18 yards) (16.5 meter) of 2 inch (5 centimeter) wide masking tape (or wider). Please see the image below and follow these steps to complete the procedure: 1) Cut one strip of masking tape equal to the width of the vehicle. Place the masking tape on the parking surface approximately 3 feet (1 meter) from and parallel to the rear bumper. This strip of masking tape will be the indicator used to adjust the RED line in Advanced Settings Step C. Guideline (Distance). 2) Cut two strips of masking tape, approximately 15 feet (4.5 meter) in length, and place them on the parking surface in the position shown in the image below, parallel to the sides of the vehicle and extending to the rear. These strips represent the width of the vehicle, and will be used instead of the painted parking lines in both the Basic Settings and Advanced Settings.

Step 3

Step 1
External Dimensions Rear view camera.. 27 (W) 27 (H) 26 (D) mm 1 (W) 1 (H) 1 (D) in. Image processing unit power supply. 84 (W) 20 (H) 65 (D) mm 3-1/4 (W) 3/4 (H) 2-1/2 (D) in. Button unit... 27 (W) 27 (H) 13 (D) mm 1 (W) 1 (H) 1/2 (D) in. Weights Rear view camera.. 150 g (0.3 lbs) (including cable) Image processing unit power supply. 200 g (0.44 lbs) (including power cord) Button unit... 95 g (0.2 lbs) (including cable) Camera Unit Imaging sensor.. 1/4-inch color CCD sensor No. of pixels... 492 (vertical) 512 (horizontal) (total no. of pixels: approx. 270 000, effective no. of pixels: approx. 250 000) Lens... Wide-angle, focal length: 1.53 mm, F value: 2.8 Angle of view.. Horizontal: approx. 135, vertical: approx. 100 IR cutoff (special vehicle-mounted) filter. Provided Iris system.. Electronic iris Scanning system.. Interlace Synchronizing system.. Internal synchronization Signal-to-noise ratio... 40 dB or more Horizontal resolution.. Approx. 300 TV lines Illumination range.. Approx. 1.5 lux to lux Operating temperature range.. 30 C to +70 C 22 F to +158 F Storage temperature range.. 40 C to +85 C 40 F to +185 F