TD-3KW_e 1

TD-3KW

Owners Manual

Thank you, and congratulations on your choice of the Roland Drum System TD-3KW.
Before using this unit, carefully read the sections entitled: USING THE UNIT SAFELY and IMPORTANT NOTES (p. 2, p. 3). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
* For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-3 must be adjusted.
Copyright 2006 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

TD-3KW_e 2

USING THE UNIT SAFELY
Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. to damage or caused with and all its to domestic
The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
Before using this unit, make sure to read the instructions below, and the Owners Manual.
Do not open or perform any internal modifications on the unit. (The only exception would be where this manual provides specific instructions which should be followed in order to put in place user-installable options; see p. 7.) Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page. Never use or store the unit in places that are:
When using the unit with a rack or stand recommended by Roland, the rack or stand must be carefully placed so it is level and sure to remain stable. If not using a rack or stand, you still need to make sure that any location you choose for placing the unit provides a level surface that will properly support the unit, and keep it from wobbling. Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.
In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit. Do not drop it!
Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are Damp (e.g., baths, washrooms, on wet floors); or are Humid; or are Exposed to rain; or are Dusty; or are Subject to high levels of vibration...

Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children. Never climb on top of, nor place heavy objects on the unit.
This unit should be used only with a rack or stand that is recommended by Roland.
Should you remove nuts, washers, screws, anchor bolts, etc., keep them in a safe place out of childrens reach, so there is no chance of them being swallowed accidentally.

TD-3KW_e 3

IMPORTANT NOTES
In addition to the items listed under USING THE UNIT SAFELY on page 2, please read and observe the following:

Placement

Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time. Such objects can discolor or otherwise harmfully affect the finish.

Maintenance

For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

Additional Precautions

Use a reasonable amount of care when using the units buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions. When connecting / disconnecting all cables, grasp the connector itselfnever pull on the cable. This way you will avoid causing shorts, or damage to the cables internal elements. To avoid disturbing your neighbors, try to keep the units volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night). This instrument is designed to minimize the extraneous sounds produced when its played. However, since sound vibrations can be transmitted through floors and walls to a greater degree than expected, take care not to allow these sounds to become a nuisance to neighbors, especially when performing at night and when using headphones.

TD-3KW_e 4

Checking the Contents of the Box
TD-3 (Percussion Sound Module) x 1 KD-8 (Kick Trigger Pad) x 1 FD-8 (Hi-Hat Control Pedal) x 1 PDX-8 (V-Pad) x 1 PD-8 (Pad) x 3 CY-5 (Cymbal Pad) x 1 CY-8 (Cymbal Pad) x 2 Connection Cables Tuning Key x 1 TD-3KW Owners Manual x 1

MDS-3C

(Drum Stand)

Assemble the Drum Stand.

About the Stand, refer to the owners manual for the stand.
Do NOT open the legs of the stand at more than 120 degrees, and NOT make the distance of both Right/Left end legs as more than 90cm (36 inches). If you do so, the stand could fall down.
The tuning key is included in the FD-8 package. The TD-3 Owners Manual is included in the TD-3 package. This package does not include a kick pedal. Use with a commercially available kick pedal. This package does not include the CY-5 attachment set for cymbal.

90 cm (36 inches)

* In the interest of product improvement, the specifications and/ or appearance of this unit are subject to change without prior notice.
(Percussion Sound Module)
Attach the mounting plate (included with the optional drum stand) to the TD-3. Using the screws attached to the bottom panel, attach the holder so the unit is oriented as shown in the diagram.

fig.TD-3.e

To attach the stand holder, remove the four 8 mm screws (M5 x 8) from the bottom of the TD-3 and use them. Use of other screws may result in damage to the unit.
When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons or controls get damaged.

Narrow

When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over.

TD-3KW_e 5

fig.PD-85.e_80

(Snare)

Tuning Bolt
Adjusting the Head Tension Before using the pad, tighten the head so that the tension is rather firm.
Looseness in the head tension may result in problems such as failure of the PDX-8s rim shots to sound or double triggering.

Hoop Rim Rubber

Head Sensor Head Stand Fixing Screw Output Jack Shell
Striking the head when the head tension is loose may damage the sensor.
1. Use a tuning key to tighten the tuning bolts.

Strike the head to check the feel and response.

fig.Adjust.e

Holder Rim Sensor

Loosen

Tighten
* Do NOT place your fingers inside the shell, as you may hurt yourself or cause damage to the PDX-8. Or when changing the head, do NOT touch any of the internal parts. Also, do not insert your fingers into the hole of the mounting bracket.
Tighten each tuning bolt one by one, observing the numerical order shown in the diagram. Do not firmly tighten a single tuning bolt by itself. Doing so will make it impossible to tension the head evenly, and will cause malfunctions.

fig.Bolt

Head Sensor Rim Sensor
2. Fine-tune the adjustment while continuing to check the pad feel and response.

Head Sensor

On the PDX-8, adjusting the head tension affects only the head response, and does not change the pitch of the sound as it would on an acoustic drum. Head tension may slacken with the passage of time. Readjust the tension as needed.

TD-3KW_e 6

fig.RimShot.e
Attaching the Pad to a Stand
Attach the PDX-8 to a pad mount of the stand.
Be sure to tighten the stand fixing screw securel. If it remain loose, double triggering may occur.

fig.Stand.e

Player
Suitable position for rim shots

Cross Stick

Only strike the rim of the pad. Depending on the instrument assigned to the rim, you can play rim shots and/or cross stick sounds.

fig.XStick.e

Playing Methods Head Shots

fig.HeadShot.e

* To play the cross stick, be sure that you only strike the rim of the pad. Placing your hand on the head of the pad might prevent the cross stick sound from being played properly. Head * Do not strike the hoop. For more on settings and tones, see the respective modules owners manual.

Rim Shots

If you hear a rim sound when you strike the head, decrease the Rim Sensitivity ( ) value. ) If you cannot get a rim sound even when you strike the rim hard, increase the Rim Sensitivity ( value.

* To play rim shots, strike the rim in the area shown in the diagram.

TD-3KW_e 7

Head Replacement When the Head Should Be Replaced
The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted. Replacement heads (optional): MH-8 Mesh Head

Specifications

PDX-8 Head Size: 8 inches Triggers: 2 (Head, Rim) Dimensions: 266 (W) x 326 (D) x 62 (H) mm 10-1/2 (W) x 12-7/8 (D) x 2-1/2 (H) inches Weight: 1.3 kg 2 lbs 14 oz Options: Mesh Head (MH-8) * The Rim rubber is one component that eventually wears out (the more so if numerous rim shots are performed), and will require replacement. Rim shots may not be performed correctly when the rim rubber is worn out. If this occurs, replace the rim rubber. Consult Roland Service for more on replacing the rim rubber.
1. Remove all tuning bolts from the PDX-8.

fig.Replace.e

Tighten Tuning Key
* Due to the nature of the materials used in the sensor, changes in room temperature may affect the sensitivity of the sensor.
Hoop Head Hoops Rubber Portion

Sensor

Do not apply excessive force to the sensor and cushion located under the head. Doing so can interfere with accurate detection, and may damage it.
2. Remove the hoop. 3. Remove the old head. 4. Place the new head on the shell. 5. Place the hoop onto the head. 6. Attach the tuning bolts to the hoop and shell. 7. Next, adjust the tension of the head. Refer to Adjusting the Head Tension (p. 5).
Do not firmly tighten a single tuning bolt by itself. Doing so will make it impossible to tension the head evenly, and will cause malfunctions.

TD-3KW_e 8

fig.PD-8.e

Playing the PD-8

fig.PD-HR.e

Stand Fixing Screw

Head Shot
PD-8 Pad Size: 8.5 inches Triggers: 2 (Head, Rim) Dimensions: 226 (W) x 280 (D) x 54 (H) mm 8-15/16 (W) x 11-1/16 (W) x 2-1/8 (H) inches Weight: 1.2 kg 2 lbs 11 oz

Output Jack

fig.PD-Set.e
Rod Pass the rod through the pipe that is inside the holder.
When attaching the PD-8s to the mounts, be sure to tighten the stand fixing screws securely. If any of them remain loose, the pad could fall off.

TD-3KW_e 9

fig.CY-8.e

(Hi-Hat)

2. Mount the CY-5 so itUSING THE UNIT SAFELY fits the lower clutch as shown below.
Pad Face Bow Portion Edge Portion Projection (Be sure to orient it correctly)

Making the Settings

When mounting the CY-5 on an L-Rod (pad mount), use ONLY the attachment set as shown below.

Upper Clutch

3. Place the clutch felt (s), and while applying some pressure, mount the upper clutch as shown.
Afterwards, you can adjust the upper clutch to have the movement you desire. If it is too loose, double triggering may occur. Be sure the ROLAND logo is on the opposite side of the playing area.

Apply pressure

Clutch Felt (S)
Tighten the bolt with a tuning key.

Clutch Felt (L)

Lower Clutch
1. Mounting the lower clutch and the clutch felt (L).
Align the notched section as shown below. Then place the clutch felt (L) so it fits securely.
Notch (Be sure to orient it correctly)
Size: 10 inches Triggers: 2 (Bow, Edge) Dimensions: 246 (W) x 246 (D) x 45 (H) mm 9-11/16 (W) x 9-11/16 (D) x 1-13/16 (H) inches Weight: 380 g 14 oz (without attachment) Accessories: Attachment Set for Hi-Hat (Upper Clutch, Lower Clutch, Clutch Felt (L), Clutch Felt (S))
* Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function.

TD-3KW_e 10

fig.CY-8.
(Crash Cymbal/Ride Cymbal)
Playing the CY-8 Bow Shot
This is the most common playing method, playing the pad face of the cymbal. It corresponds to the sound of the headside of the connected trigger input.

fig.CY-Bow.e

Pad Face Bow Portion Edge Portion

Edge Shot

This playing method involves striking the edge with the shoulder of the stick. It corresponds to the sound of the rimside of the connected trigger input. * To make use of edge shot, youll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots.

fig.CY-Edge.e

Attaching the Cymbal Pad to a Stand
1. Use a tuning key to tighten the stopper bolt.
The stopper keeps the cymbal pad from turning, and prevents the cables from catching or getting tangled on the stand.

fig.CY-Set01.e

Stopper (Be sure to orient it correctly)

Choking

Choking (pinching) the cymbals edge with the hand immediately after hitting the cymbal makes the sound stop. * To make use of choking play techniques, youll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots.

fig.CY-Choke

2. Attach the CY-8 so the Roland logo is positioned on the opposite side of the playing area. 3. Tighten the wing nut to obtain the desired movement.
Use the included felt washer and the wing nut.

fig.CY-Set02.e

Wing Nut Felt Washer
CY-8 Size: 12 inches Triggers: 2 (Bow, Edge) Dimensions: 290 (W) x 295 (D) x 47 (H) mm 11-7/16 (W) x 11-5/8 (D) x 1-7/8 (H) inches Weight: 650 g / 1 lb 7 oz Accessories: Wing Nut, Felt Washer, Stopper * Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function.
Double sounding may occur if the wing nut is loose.

TD-3KW_e 11

fig.FD-8.e

(Hi-Hat Control Pedal)

Using the FD-8
Using the FD-8, you can control the opening and closing of the hi-hat sound.
Adjusting the Travel of the Pedal
Loosen the nut with a tuning key. After adjusting, tighten the nut. deep Shift the Arm

Open Hi-Hat

Strike the hi-hat without pressing the pedal

Half Open Hi-Hat

shallow
Strike the hi-hat with the pedal pressed half-way

Closed Hi-Hat

Pedal Plate Anchor Bolt
Strike the hi-hat with the pedal pressed

Foot Closed

Completely press down the pedal

Control Out Jack

Attaching the Anchor Bolts (When Using on the Carpet)
Anchor Bolt Spring for the Anchor Bolt
The volume of the Foot Closed sound can be adjusted separately (TD-3 Owners Manual; p. 42).
Connect the FD-8 to the TD-3 before turning on the power. Do NOT press the pedal when turning on the power.
The tips of the anchor bolts are sharp. Handle with care. When using on flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. When the FD-8 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal. To avoid damage, do not leave the FD-8 for extended periods of time with the pedal plate depressed.
FD-8 Dimensions: 130 (W) x 396 (D) x 103 (H) mm 5-1/8 (W) x 15-5/8 (D) x 4-1/16 (H) inches Weight: 1.3 kg 2 lbs 14 oz Accessory: Tuning Key

TD-3KW_e 12

fig.KD-8.e

(Kick)

3. Use a tuning key supplied with the FD-8 to tighten the screws removed in Step 1 so that the stand is firmly secured.

fig.KD-Assy03

Anchor Bolt

Foot Plate

4. Attach the kick pedal.
Position the beater so that it strikes the center of the head, then secure the kick pedal and KD-8 firmly in place.

fig.KD-Assy04.e

1. Remove the screws attached to the reverse side of the KD-8s trigger.

fig.KD-Assy01

Beater
Install the kick pedal securely.
Adjusting the Foot Plate Height
2. Pull out the stand in the direction indicated by the arrow until it is fully extended.

fig.KD-Assy02

Depending on your kick pedal, it can be unstable when you attach it to the KD-8. Be sure to adjust the foot plate height so that the entire bottom surface of the pedal is attached to the floor.

fig.KD-Assy05.e

Commercially Available Kick Pedal
* Adjust the height so that the entire pedal comes into contact with the floor.

TD-3KW_e 13

1. Loosen the stands anchor bolts and remove the foot plate.

fig.KD-Assy06

Adjusting the Anchor Bolts UNIT SAFELY USING THE
When using the kick pedal on a carpet or similar surface, adjust the anchor bolts so their tips protrude from the plate and secure the pedal in place; this will make it easier to use the kick pedal. However, when used on flooring, the anchor bolts may damage the floor. Adjust the anchor bolts correctly.

fig.KD-Anchor.e

Adjusting the Anchor Bolts

When Using on the Carpet

When using on the Floor
The tips of the anchor bolts are sharp. Handle with care.
2. Set the kick pedal so that the entire bottom surface is attached to the floor. 3. In most cases, the stand becomes somewhat floated. Tighten the anchor bolts securely there to fix the stand and foot plate.

fig.KD-Assy07.e

When Using a Twin Pedal

fig.KD-Pedal1

Position the two beaters equally apart from the center of the pad as shown in the figure at left. If one of the beater is further away from the center than the other, the sound from the further beater will be lower in volume, or will not sound as desired.

fig.KD-Pedal2

This hight will vary depending on your kick pedal.
Using a twin pedal will result in lower sensitivity as compared to when a single pedal is used. Raise the sensitivity on the sound module.
Install the kick pedal securely. Take care not to pinch your fingers. The tips of the anchor bolts are sharp. Handle with care. When moving the setup, be sure to remove the screws and fold the stand. Transporting the KD-8 while it remains open may subject the stand to excessive strain and result in damage to the stand.

KD-8 Dimensions: 272 (W) x 260 (D) x 405 (H) mm 10-3/4 (W) x 10-1/4 (D) x 16 (H) inches Weight: 2.9 kg 6 lbs 7 oz Accessory: Screws * Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function.

TD-3KW_e 14

. USING THE UNIT SAFELY

Assemble the TD-3KW

Using the provided cables, connect the pads. Connect the L-shaped plugs of the included cables to the pads.
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.

fig.Setting1.e

Trigger Inputs

T3 T2 T1 SNR KIK

HHC RD

CR1 HH

CY-5 TD-3 PDX-8 PD-8

PD-8 KD-8

SNR KIK HHC

fig.Label

1. Insert the plugs of connecting cables into the TRIGGER INPUTS jacks on the rear of the TD-3. 2. Insert the L-sharped plugs into the TRIGGER OUTPUTS jacks of the pads.
* When you connect the cables, please refer to the labels that are attached to both ends of the cables.

TD-3KW_e 15

Trigger Settings For TD-3
For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-3 must be adjusted.
For more detailed informations, refer to the TD-3 Owners Manual.
Adding the Optional Pads to the TD-3KW
When adding a new pad, use trigger input CRASH2.

Examples Adding a Cymbal

Adding the CY-8 or the CY-5 for a 2nd Crash or a Splash Cymbal. For mounting, use the Cymbal Mount MDY-10U.

Adding a Tom

Adding the PD-8 for a 2nd floor tom. For mounting, use the Pad Mount MDH-10U.

Options

Kick Trigger Pad: V-Kick Trigger Pad: Dual Trigger Pad: V-Pad: Cymbal Pad: V-Cymbal: Pad Mount: Cymbal Mount: KD-8, KD-7 KD-85, KD-120 PD-8 PDX-8, PD-85, PD-105, PD-125 CY-8, CY-5 CY-12R/C, CY-14C, CY-15R MDH-10U MDY-10U

TD-3KW_e 16

Information

AFRICA

Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.

PHILIPPINES

G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801

FINLAND

Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)24 020

HONG KONG

Tom Lee Music Co., Ltd. Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T.S.T, Kowloon, HONG KONG TEL: 2333 1863

CENTRAL/LATIN AMERICA

ARGENTINA
Instrumentos Musicales S.A. Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700

U.A.E.

Zak Electronics & Musical Instruments Co. L.L.C. Zabeel Road, Al Sherooq Bldg., No. 14, Grand Floor, Dubai, U.A.E. TEL: (04) 3360715

MEXICO

Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699

UNITED KINGDOM

Roland (U.K.) Ltd. Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 702701

GERMANY

Roland Elektronische Musikinstrumente HmbH. Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090

NICARAGUA

Bansbach Instrumentos Musicales Nicaragua Altamira D'Este Calle Principal de la Farmacia 5ta.Avenida 1 Cuadra al Lago.#503 Managua, Nicaragua TEL: (505)277-2557

BARBADOS

A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St.Michael, Barbados TEL: (246)430-1100

GREECE

STOLLAS S.A. Music Sound Light 155, New National Road Patras 26442, GREECE TEL: 2610 435400

MIDDLE EAST

BAHRAIN
Moon Stores No.16, Bab Al Bahrain Avenue, P.O.Box 247, Manama 304, State of BAHRAIN TEL: 005

NORTH AMERICA

CANADA
Roland Canada Music Ltd. (Head Office) 5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) Roland Canada Music Ltd. (Toronto Office) 170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707
Rivera Digitec (India) Pvt. Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051

BRAZIL

Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666

PANAMA

SUPRO MUNDIAL, S.A. Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101

HUNGARY

Roland East Europe Ltd. Warehouse Area DEPO Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011

INDONESIA

PT Citra IntiRama J1. Cideng Timur No. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170

CYPRUS

Radex Sound Equipment Ltd. 17, Diagorou Street, Nicosia, CYPRUS TEL: (022) 66-9426
Comercial Fancy II S.A. Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540

TD-3KW_l_TrigParam_e 1

For TD-3KW Owners

Read This First PDX-8 Snare Settings Required
Use of the setup without the following may prevent the PDX-8s rim shots from sounding, cause double triggering, or result in other problems.
1. Tune the Head 2. Make the Settings for the Trigger Parameters
Make the trigger parameter settings with the TD-3 percussion sound module. Follow the procedures below.
* The TD-3's default factory settings are not suitable for use with the PDX-8.
Trigger Parameter Trigger Type Mask Time Rim Sensitivity

Display

Value 80r (712) (*1: See below.)
3. Adjust the Rim Sensitivity
If you find the following kinds of problems occurring, adjust the Rim Sensitivity.
If you hear a rim sound when you strike the head, decrease the Rim Sens value. If you cannot get a rim sound even when you strike the rim hard, increase the Rim Sens value.
How To Set the Trigger Parameters ( TD-3 Owners Manual; p. 50 )
1. Press [LEVEL/PAN] + [TEMPO] on the TD-3.
[EDIT] flashes and appears in the display, then the trigger type value is indicated.

2. 3. 4. 5.

Strike the PDX-8.
The SNARE trigger indicator lights.
Press [EDIT] to select the parameter ( , etc.). Press [+] or [-] to make the setting. Press [DRUM KIT]; the [EDIT] light goes off.
* Do not turn off the power without the [EDIT] light having gone out. Otherwise you will lose the change you have just made.
Copyright 2006 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
TD-3KW LEAFLET Trigger Parameter

40674256