s re sp

e ot s

Sa le s&

Operation and maintenance manual
Before using the machine, please read the attached operating instructions. Carefully read the safety rules

Mode d'emploi

Veuillez lire attentivement le mode d'emploi (notamment les consignes de scurit) avant d'utiliser l'appareil.

FOR HOUSEHOLD USE ONLY

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 2 Do not touch hot surfaces. Use handles or knobs. 3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or appliance in water or other liquid. 4 Close supervision is necessary when any appliance is used by or near children. 5 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. 6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any way. Return appliance to the nearest authorized service centre for examination, repair or adjustment. 7 The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury. 8 Do not use outdoors. 9 Do not let cord hang over edge of table or counter, or touch hot surfaces. 10 Do not place on or near a hot gas or electric burner, or in a heated oven. 11 Always turn appliance OFF, then plug cord into the wall outlet. To disconnect, turn switch to OFF, then remove plug from wall outlet. 12 Do not use appliance for other than intended household use. 13 Use extreme caution when using hot steam.

SAVE THESE INSTRUCTIONS

This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service centre. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no user serviceable parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during operation. 4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft cloth dampened with water. 5 For optimal taste of your coffee, use purified or bottled water. Periodic descaling is still recommended every 2-3 months.

CAUTION

A A short power-supply cord is provided to reduce risks of tangling or tripping over a longer cord. B Longer extension cords are available and may be used if care is exercised in their use. C If a long extension cord is used: 1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. 2 if the appliance is of the grounded type, the extension cord should be a grounding type 3 the cord should not hang from the table to avoid the risk of tangling or tripping.
INSTRUCTIONS FOR THE POWER SUPPLY CORD

CONTENTS

GENERAL INFORMATION.... 3 APPLIANCE..... 4

ACCESSORIES..... 4

INSTALLATION.... 5
STARTING THE MACHINE..... 5 SETTING THE LANGUAGE..... 6
AQUA PRIMA WATER FILTER..... 7

DISPLAY..... 8

(OPTI-DOSE) INDICATES THE GROUND COFFEE QUANTITY.... 8

ADJUSTMENTS..... 9

COFFEE INTENSITY.... 9 ADJUSTING THE HEIGHT OF THE DRIP TRAY..... 9 COFFEE GRINDER ADJUSTMENT..... 9
BEVERAGE DISPENSING..... 10

ESPRESSO

/ COFFEE / LONG COFFEE..... 10
DISPENSING BEVERAGES WITH GROUND COFFEE.... 11 HOT WATER DISPENSING..... 12 DISPENSING STEAM..... 13 MAKING CAPPUCCINO.... 14 MILK ISLAND (OPTIONAL).... 15
BEVERAGE PROGRAMMING... 16
1. PROGRAMMING FOR SELF-LEARNING.... 16 2. PROGRAMMING FROM THE BEVERAGE SETTINGS MENU... 16
PROGRAMMING THE MACHINE... 18

MACHINE SETTINGS..... 19

LANGUAGE MENU..... 19 WATER HARDNESS MENU.... 20 ACOUSTIC ALARM MENU..... 20 FILTER ALARM MENU..... 21 RINSE MENU..... 21 CUP WARMING SURFACE MENU.... 21 CLOCK SETTING MENU..... 22

MAINTENANCE.... 25

WATER FILTER MENU..... 25 DESCALING MENU..... 27 BREW GROUP WASHING..... 30
PROGRAMMING THE MACHINE... 31
ENERGY SAVING..... 31 TURN OFF DELAY.... 31 TIMER SETTING
..... 31 MONDAY TIMER SETTING.... 32

SPECIAL FUNCTIONS.... 33

RESTORE SETTINGS..... 33
CLEANING AND MAINTENANCE.... 34
GENERAL MACHINE CLEANING..... 34 CLEANING THE BREW GROUP..... 35
ERROR CODES.... 36 TROUBLESHOOTING.... 37 SAFETY RULES.... 38 TECHNICAL DATA..... 40

GENERAL INFORMATION

The coffee machine is suitable for preparing espresso coffee using coffee beans, and it is equipped with a device to dispense steam and hot water. The machine is designed for domestic use only, and is not suitable for heavy or professional use. Warning: no liability is assumed for any damage caused by: incorrect use not in accordance with the intended uses; repairs not carried out by authorized customer service centres; tampering with the power cable; tampering with any part of the machine; the use of non-original spare parts and accessories; failure to descale the machine or use at temperatures below 0C (32F)
IN THESE CASES, THE WARRANTY IS NOT VALID.
THE WARNING TRIANGLE INDICATES ALL IMPORTANT INSTRUCTIONS FOR THE USERS SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS INJURIES!
HOW TO USE THESE OPERATING INSTRUCTIONS.
Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee machine. For further information or in case of problems, please refer to any authorized service centre.

APPLIANCE

Coffee bean hopper Coffee bean hopper cover Cup warming surface Control panel SBS knob Dispensing head Service door Dregs drawer Compartment for preground coffee Power button
Hot water / steam knob Button for raising/lowering the drip tray
Hot water / steam spout Water tank Brew Group Milk Island connection Drip tray

Socket for power cable

ACCESSORIES

Aqua Prima

Ground coffee measuring scoop

Water hardness tester

Cleaning brush

Grinder adjustment key

Power cable

INSTALLATION

STARTING THE MACHINE
Make sure that the main power button is not pressed in the ON position.
Remove the coffee bean hopper cover. Fill the hopper with coffee beans.
Close the cover pushing it down completely.
Remove the water tank. We recommend installing the Aqua
Fill the tank with fresh drinking water. Do not exceed the max level indicated on the water tank. the machine.
Attach the female end of the power cord to the machine. Insert the male end into the power outlet (see data tag).
Place a container beneath the hot water spout.
The machine automatically primes the water circuit. The machine is now ready for use.
Water may not be dispensed into the container. This should not be considered a malfunction.
Press the main power button to the ON position.
TO ASSESS WATER HARDNESS, SEE WATER HARDNESS MENU ON PAGE 20.

SETTING THE LANGUAGE

These settings allow you to regulate the machines parameters to dispense coffee according to the typical parameters of the country where it is used. For this reason, the languages are also differentiated by location.

1 beverage settings

2 machine settings
Select machine settings by navigating Press selection.

2.1 language English

Press selection.
Select by navigating the click
When the desired language is displayed, press.
The machine now displays the messages in the language selected.
Press until the following message is displayed.
Wait until the machine completes the heating stage. When the right temperature is reached, the machine performs a rinse cycle in the internal circuits. A small quantity of water is dispensed. Wait for this cycle to be completed automatically. The screen for product dispensing appears on the display. See page 8.

AQUA PRIMA WATER FILTER

To improve the quality of the water you use, and guarantee longer machine life at the same time, it is
Remove the Aqua Prima water date of the current month. until it clicks into place.
Fill the tank with fresh drinking tank for 30 minutes for correct initialization.

3 maintenance

1. 2. Place a container beneath the steam/hot water spout. Press. Select maintenance and press the button.

3.1 water filter

3.1.3 activate filter execute now
1. 2. Press again. position. Turn the knob to the Water dispensing begins.

button.

exit message is displayed. Then press
). Press. The machine is now ready for use.

a few times until the

DISPLAY
Accessing the programming menu
strong aroma espresso coffee 08:33

Steam button

Click wheel
Select the coffee bean dose or the quantity of pre-ground coffee

Hot water button

Press the
button twice to make 2 cups. Press twice

selected espresso coffee

selected double espresso
order to grind the second serving of coffee. Coffee dispensing is then restarted and completed.
(OPTI-DOSE) INDICATES THE GROUND COFFEE QUANTITY
It is possible to choose three options (strong, button. medium and mild) by pressing the These indicate the quantity of coffee the machine grinds for each beverage. This button is also used to select the pre-ground coffee function.
strong aroma espresso coffee 08:33 medium aroma espresso coffee 08:33 mild aroma espresso coffee
SELECT THE AMOUNT OF COFFEE TO BE GROUND BEFORE DISPENSING THE BEVERAGE.
pre-ground espresso coffee

ADJUSTMENTS

COFFEE INTENSITY
The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply turn the dial and you will notice that the coffee goes from mild intensity to strong intensity. MEDIUM COFFEE

SBS SAECO BREWING SYSTEM

SBS adjusts the intensity of the brewed coffee. The coffee may even be adjusted while brewing. This adjustment has an immediate effect on the selected type of brewing.

MILD COFFEE

STRONG COFFEE
ADJUSTING THE HEIGHT OF THE DRIP TRAY
Adjust the drip tray before dispensing any beverages so as to be able to use any kind of cup. To raise the drip tray, press lightly on the lower part of the button. To lower the drip tray, press lightly on the upper part of the button. When the desired height is reached, release the button. is necessary to empty the tray.
COFFEE GRINDER ADJUSTMENT
The machine lets you make slight adjustments to the coffee grinder to adapt it to the kind of coffee used. The adjustment must be performed by pressing the pin located inside the coffee hopper. This must be turned by means of the supplied key only. Turn the pin one notch at a time and brew 2-3 cups of coffee; the grinder adjustment can only be noticed in this way. The references located inside the container indicate the grind setting. FINE GRIND MEDIUM GRIND COARSE GRIND

BEVERAGE DISPENSING

COFFEE BREWING CAN BE STOPPED AT ANY TIME BY PRESSING THE BUTTON AGAIN. THE STEAM SPOUT MAY REACH HIGH TEMPERATURES: DANGER OF SCALDING. DO NOT TOUCH IT WITH BARE HANDS.
Check that all the containers are clean. To carry out this operation, follow the instructions in the Cleaning and Maintenance section (see page 34). serving of coffee. Coffee dispensing is then restarted and completed.
ESPRESSO / COFFEE / LONG COFFEE
This procedure shows how to dispense an espresso. To dispense another type of coffee, select it by navigating
Position 1 - 2 cup(s) to dispense an espresso
Position 1 - 2 cup(s) to dispense a regular coffee or a long coffee
Select the desired beverages by navigating the click wheel with
If desired, select the quantity of coffee to be ground by pressing the button one or more times.
Press the button: once for 1 cup and twice for 2 cups. The machine begins dispensing the selected beverage.
The machine ends dispensing automatically on the basis of the quantity determined by the manufacturer. It is possible to customize this quantity (see page 16).
DISPENSING BEVERAGES WITH GROUND COFFEE
The machine allows you to use pre-ground and decaffeinated coffee. Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean hopper. Only use coffee ground for espresso machines and never coffee beans or instant coffee.
WARNING: ONLY PUT PRE-GROUND COFFEE INTO THE COMPARTMENT WHEN YOU WISH TO DISPENSE THIS TYPE OF BEVERAGE. ONLY INSERT ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE DISPENSED AT THE SAME TIME. The preparation of an espresso using pre-ground coffee is shown in the example given below. The customized choice of using pre-ground coffee is shown on the display.
pre-ground espresso coffee 08:33
insert ground coffee and press ok
2. 1. Select the desired beverage by navigating the click wheel with Select the function by pressing the button until the pre-ground option appears. Press the A message reminds the user to pour ground coffee into the appropriate compartment.
brewing in progress please wait
Pour one scoop of ground coffee into the appropriate compartment using the measuring scoop provided.

Press the brewing.

button to start
Note: If brewing does not start within 30 seconds from the appearance of the message (3), the machine will return to the main menu and discharge any inserted coffee into the coffee grounds drawer; If no pre-ground coffee is poured into the compartment, only water will be dispensed; If the dose is excessive or if 2 or more scoops of coffee are added, the machine will not dispense the beverage and the coffee in the compartment will be discharged into the grounds drawer.

button to:

- save the new settings.

1 Press the 1

select the functions change the function settings.

4 energy saving

Beverage setting (see page 16)

2 machine settings 5

Energy saving (see page 31)

special functions

Machine settings (see page 19)
Special functions (see page 33)
Maintenance (see page 25) To exit the programming mode:

MACHINE SETTINGS

To change the machines operation settings, press the the
button, select machine settings and press

rinsing on

set the menu language.

2.2 water hardness 3

set the coffee circuit rinse cycle.
2.6 cup-warming surface off

set the water hardness.

2.3 acoustic alarm on
activate/deactivate the operation of the cup warming surface

2.7 clock setting

set/activate the acoustic alarms.

2.4 filter alert on

To set the current time, date and hour format to display.
activate/deactivate the Aqua Prima
To exit any level of machine settings without saving the changes made, press the button. For example:

LANGUAGE MENU

> machine settings > language. To change the language of the display.
1. 2. Select the desired language. After selected, the machine displays all the messages in the language selected.

WATER HARDNESS MENU

> machine settings > water hardness With the Water hardness function you can adapt your machine to the degree of hardness of the water you use, so that the machine will request descaling at the right moment. Hardness is expressed on a scale from 1 to 4. The machine is preset at value 3.
1 Immerse the water hardness tester included with the machine in water for one second.
Check the value. The test can be used for one measurement only.
1. 2. Set the water hardness obtained from the test and save it.

ACOUSTIC ALARM MENU

> machine settings > acoustic alarm To turn on/off a tone each time a button is pressed.
3 Select by navigating the click
It is possible to set: - on - off Press the button to save.

FILTER ALARM MENU

> machine settings > filter alert

RINSE MENU

> machine settings > rinsing The rinse setting the internal circuits in order to guarantee that the beverages are only made with fresh water. The function is enabled as default by the manufacturer. Note: This rinse cycle is performed every time the machine is turned on after the warming phase.

2.5 rinsing on

CUP WARMING SURFACE MENU
> machine settings > cup-warming surface To turn on/off the operation of the cup warming surface located on the top of the machine.A warm cup allows you to fully savour the coffee and taste its full aroma.

CLOCK SETTING MENU

> machine settings > clock setting To set the current time, date and hour format to display.
In this menu you can set: - the current time (hour and minutes) - the hour format (24 hours - AM/PM) - the current date (day - month - year day of the week) - the date format (American international).

Time setting

> machine settings > clock setting > time setting To set the current time on the machine

2.7.1 time setting 16:54

1. 2. Set the time by navigating the Save using the button.
1. 2. Set the minutes by navigating the Save using the button.

Time format

> machine settings > clock setting > time format To set the time view mode. This setting adjusts all clock functions to either am/pm or 24 hour formats.

2.7.2 time format 24h

1. 2. 2.
The machine also allows displaying the time in the American format (am/pm). 2.

Date setting

> machine settings > clock setting > date setting To set the date (day, month, year, day of the week).
2.7.3 date setting tuesday 18/04/06
1. 2. Select the day and press the
1. 2. Select the month and press the
1. 2. Select the year and press the
The day of the week is automatically set according to the set date.

Date format

> machine settings > clock setting > date format setting the date.
2.7.4 time format GG/MM/AAAA
The machine also allows displaying the date in the American format (MM/GG/AAAA).

MAINTENANCE

To access the machines maintenance programs, press the the

3.1 water filter 3.3

button, select maintenance and press

group wash

wash the Brew Group.

3.2 descaling

management menu.

WATER FILTER MENU

> maintenance > water filter
In this menu you can: - check the number of litres before replacement;

following message appears on the display:
descaling cycle please wait

passage [ 2/15]

fill the water tank
The machine begins to dispense the descaling solution through the hot water spout. The dispensing occurs at predetermined intervals, in order to allow the solution to be more effective.
The intervals are displayed in such a way as to check the state of progress of the process.
Remove the water tank, rinse with fresh drinking water to eliminate traces of descaling drinking water.
Insert the tank with fresh drinking water.
rinse cycle ok to start cycle

rinse cycle please wait

rinse cycle completed
Rinse the machines circuits by pressing the button.
The machine performs the rinse cycle. During the rinse cycle, the machine may require the water tank
following screen appears. Then the display shows the maintenance screen.
When descaling is complete, return to the main menu to dispense beverages.
Turn the knob until it is in the rest position ( ). Check the quantity of water in the tank and desired.

Brew Group Washing

> maintenance > group wash To clean the machines internal circuits used for brewing coffee. To wash the Brew Group, simply clean with water as shown on page 35. This wash completes maintenance of the Brew Group. We recommend using Saeco tablets, which can be purchased separately. Note: before performing this function make sure that: 1. a large enough container is positioned under the spout; 2. the appropriate tablet for cleaning the Brew Group has been inserted into the compartment for pre-ground coffee; THE WASH CYCLE CANNOT BE INTERRUPTED. A PERSON MUST BE PRESENT DURING THE OPERATION.

3.3 group wash

3.3.1 group wash do it now
insert tablet and press start

group wash please wait

Insert the tablet as shown above. Press to start.
Wait for the cycle to end.

passage [2/3]

wash cycle completed please wait
You can check the status of washing.
The Brew Group has been washed. Exiting programming mode. (see page 18)

ENERGY SAVING

To adjust the energy saving parameters, press the button, select energy saving and press the

turn-off delay 180

monday
Set the time which must pass after the last product dispensing before the machine enters the energy saving mode.

4.2 timer setting off

Set the machines turn on/off times (one setting for each day of the week)
Enable/disable the machines turn on/ off times programmed for the days of the week.

TURN OFF DELAY

> energy saving > turn-off delay By default, the off delay time is set at 180 minutes.

4.1 turn-off delay 180

It is possible to set: - 15 miniutes - min - 180 miniutes - max Press the button to save.

TIMER SETTING

> energy saving > timer setting The set times (timer) for the days of the week will only operate if this function is activated. If this is not the case, the timers will have no effect on the machines operation.

MONDAY TIMER SETTING

> energy saving > monday This and the following menus are used to set the turn on/off times for each day of the week. The procedure described below shows how to set the turn on/off times for the day of the week Monday. To set the turn on/off times for the other days of the week, follow the same procedure after selecting the desired day.

4.3 monday

4.3.1 switch on monday 8:00
4.3.2 switch off monday 8:00
1. 2. Set the turn on time by navigating the
1. 2. Set the minutes by navigating the
1. 2. Set the turn off time by navigating the
1. 2. Set the minutes by navigating the Press to exit the programming of the selected day.
You can set the turn on/off times for all the days of the week.
other days you want to program.

SPECIAL FUNCTIONS

This menu allows you to access special functions present on the machine. Press the button to access and select special function and press the button. Navigate the
reset settings execute now
restore the basic machine operating parameters.

RESTORE SETTINGS

> special function > reset settings The function for restoring all the factory settings is contained in this menu. This function is particularly important for restoring the basic parameters. ALL THE CUSTOM SETTINGS WILL BE LOST AND CANNOT BE RECOVERED. AFTER RESTORING FACTORY SETTINGS, YOU WILL NEED TO RE-PROGRAM ALL THE MACHINE FUNCTIONS, IF DESIRED.

GUIDE MESSAGE THAT APPEARS out of service (xx) restart to fix
close coffee bean lid fill container wth coffee insert the brew group insert grounds drawer empty grounds empty grounds drawer
close door fill the water tank. empty the drip tray change the filter
Open the side door and empty the drip tray located under the Brew Group. 1. 60 litres of water have been dispensed; 2. 90 days have passed since its installation; 3. 20 days have passed and the machine has not been used. Note: this message only appears when on has been selected
carafe missing milk island missing
The steam knob has been turned to the position and either the Milk Island has not been installed or the carafe is not positioned correctly. Install the Milk Island or position the carafe correctly. Otherwise, turn the knob until it is in the rest position ( ). A descaling cycle must be performed on the machines internal circuits. Press the button.
descale stand-by energy saving

TROUBLESHOOTING

PROBLEMS
The machine does not turn on.

CAUSES

The machine is not connected to the power source.

SOLUTIONS

Connect the machine to the power source.
The plug has not been plugged into the Insert the plug into the machines power back of the machine. socket. Hot water or steam is not dispensed. Coffee has little crema. The hole of the steam spout is clogged. Clean the hole of the steam spout using a pin. The coffee blend is unsuitable or coffee Change coffee blend. is not freshly roasted. SBS system knob turned towards the left The Brew Group does not come out. The Brew Group is out of place. Turn the SBS system knob to the right Turn the machine on. Close the service door. The Brew Group is automatically placed in the correct position.
Dregs drawer is inserted.

Brew Group.

Fill the water tank and prime the circuit again. Clean the Brew Group. Change coffee blend. Decrease the dose.

Coffee is not brewed.

Water tank is empty. Brew group is dirty.
Coffee is brewed slowly. Brew group dirty. Coffee leaks out of the dispensing head. Dispensing head is clogged.
Clean the Brew Group. Clean the dispensing holes with a soft cloth.
Please contact the service centre for any problems not covered in the above table or when the suggested solutions do not solve the problem.

SAFETY RULES

IN CASE OF EMERGENCY
IMMEDIATELY UNPLUG THE CORD FROM THE OUTLET.

ONLY USE THE APPLIANCE

Indoors. For preparing coffee, hot water and for frothing milk. For domestic use. By adults in non altered psycho-physical conditions.
PRECAUTIONS FOR THE USE OF THE MACHINE
Do not use the machine for purposes other than those indicated above, in order to avoid danger. Do not introduce any substances other than those indicated in the instruction manual. Fill the water tank only with fresh drinking water: Hot water and/or any other liquid may damage the machine. Do not use carbonated water. Before manipulating the coffee grinder, turn of the machines main switch and unplug the cord. Do not put instant coffee or whole bean coffee in the ground coffee container.
CONNECTION TO ELECTRICAL POWER
The connection to the electrical network must be carried out in accordance with the safety regulations in force in the users country. The machine must be connected to a socket which is: compatible with the type of plug installed on the machine; effectively grounded. The power cord must not: be crushed and/or come in contact with sharp surfaces; be used to move the machine; be used if damaged; be handled with damp or wet hands; be wound in a coil when the machine is being operated. Be tampered with.
Do not install the machine in areas where water could be sprayed. Optimal operational temperature: 10C - 40C / 50-104 degrees Fahrenheit maximum humidity: 90%. The machine should be installed in an adequately lit, ventilated, hygienic location and the electric socket should be within easy reach. Do not place on heated surfaces! Install it at least 10 cm / 4 from the walls and cooking surfaces. Do not use in places where the temperature may drop to a level equal to and/or lower than 0C / 32 degrees Fahrenheit. If the machine has been exposed to such conditions notify the customer service center, who will have to carry out a safety check. The machine must not be used in an explosive or volatile atmosphere or where there is a high concentration of dust or oily substances suspended in the air. Do not install the machine on top of other appliances.

DANGERS

The appliance must not be used by children and persons who have not been informed of its operation. The appliance is dangerous to children. When left unattended, unplug from the electrical outlet. Keep the coffee machine packaging out of the reach of children. Never direct the jet of hot water and/or steam towards yourself or others. Danger of scalding. Do not insert objects through the appliances openings. (Danger! Electrical Current!). Do not pull out the plug by yanking on the power cord or touching it with wet hands. Warning. Danger of burning when in contact with hot water, steam and the hot water spout.

FAILURES

Any repairs must be performed by an authorized customer service center. Do not use the appliance with a defective power cord. The manufacturer or its customer service center will have to replace the power cable if damaged. (Caution! Electrical Current!) Turn off the appliance before opening the service door. Danger of burns!

CLEANING / DESCALING

For cleaning the milk and coffee circuits use only recommended detergents provided with the machine. These detergents must not be used for other purposes. Before cleaning the machine, the main switch must be turned to OFF (0), unplugged from the socket and cooled down. Keep the appliance from coming into contact with splashes of water or immersing in water. Do not dry the machines parts in conventional or microwave ovens. The machine and its components must be cleaned and washed after the machine has not been used for a certain period.

REPLACEMENT PARTS

For safety reasons, use only original replacement parts and original accessories.

WASTE DISPOSAL

- The packing materials can be recycled. - Appliance: unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with eu directive 2002/96/ec. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this household waste disposal service or the shop where you purchased the product.

FIRE SAFETY

Do not use water or dry-powder extinguishers.

TECHNICAL DATA

Nominal voltage Power rating Power supply Shell material Size (w x h x d) Weight Cable length Control panel Water tank Coffee bean hopper capacity Pump pressure Boiler Coffee grinder Quantity of ground coffee Dregs drawer capacity Safety devices See label on the appliance See label on the appliance See label on the appliance ABS - Thermoplastic 320 x 370 x 400 mm - 12.60 x 14.57 x 15.Kg - 19.8 lbs 1200 mm - 47.24 Front (display 2 x 24 characters) 1.7 liters - 57.5 oz / Removable 250 grams - 8.9 oz / coffee beans 15 bar Stainless steel With ceramic burrs 7 - 10.5 grams / 0.25 - 0.37 oz. 14 Boiler pressure safety valve Double safety thermostat.
Subject to engineering and manufacturing changes due to technological developments. The machine conforms to the European Directive 89/336/EEC (Italian Legislative Decree 476 dated 04/12/92) concerning electromagnetic compatibility.

Updated 4/04/08

Talea Ring Plus
Esp. E74104 Rev.01 Brew Group Esp. E90042 Rev.02

SAECO No.

SUP032BR Talea Ring Plus E74104 Rev.01 Cod 10001550 Outlet Cover, Water Tank Silv Lid, Water, Talea Ring + Water Tank, Talea Ring + Filter, Water Tank O-Ring, Metric, Epdm, 0019-10 SPRING FOR WATER CONTAINER VALVE P0049 GREY WATER CONTAINER VALVE INSERT P0049 TRANSP.VALVE FOR WATER CONTAINER P0049 BLACK LID FOR DUCKBILL VALVE UPPER TECHMATE INSERT FOR BOX P0053 LOWER TECHMATE INSERT FOR BOX P0053 Box, Talea Knob, Water-Steam,Chrome P0053 SCREW PT TORX 3X10 WN 1411 GALVANIZ SILVER PLATE LOGO SAECO NEW P0049/P0053 Cover w/opening Inferred Lens Cover BLACK PLATE WITH LOGO TALEA P053 RING PL O-Ring, Epdm, 2018 Cap Cover, Connector Black Wheel, Casing Bottom Left Side Casing Titanium STEAM TUBE WASHER P0049 Spring, Folk, Italia Power Board, I/O Lid, Bean Hopper BLACK POWER BOARD PROTECTION P0053/B-C Lid, Preground, Talea Touch Bean Hopper, Talea Ring + Mounting Plate Assy, W/Pin CUP SOCKET EN 60320 C 13 Switch, SAIA 3292 Right Side Casing Titanium Insert,Bottum on-off,Titanium Buttom,On-off,Chrome Drip Tray, Brew Group, TR+ Dump Box, Black Inside Cover Door, Black MAGNET FOR FLOAT SUPERAUTOM. BLACK DOOR PIN P0049 SPRING FOR LOCK P0049 Right Side Door, TR + Grinder Adjustment Key, Black Manual,Talea Ring Plus,P0053/C Filter, Aqua Prima Brush, Cleaning Cord, Electrical BLACK REED SENSOR SUPPORT P0049 WATER HARDNESS TEST Scoop, Preground, Charisma Lid, Cupwarming, Silver 120V SILVER WARM CUPS FINGER PROTECTION P0053 O-Ring, Epdm, 2137 SPRING FOR ON-OFF BUTTON P0049 SILICONE GREASE CONFECTIONS 2 Pole Connector, Sensor Door

Special Order No.

Yellow = Not Available unless Special Ordered
11001298 #N/A #N/A #N/A #N/A #N/A #N/A 11002030 #N/A 11002016 #N/A 11001659 #N/A #N/A #N/A #N/A #N/A #N/A 140329461 #N/A #N/A 11003889

11004922

11001624

11003782

12000280

9161.11001362

11003154 301.11005040 1501.098
Rev. 01-09/11/06 Brew Group Rev.02 1
SUP032BR Talea Ring Plus E74104 Rev.01 Cod 10001550 Adjustment knob, p124 Connector,Internal,Coffee Disp Lens, Dispenser,Ambra P0053 Cover, Dispensing Head, Chrome Lid,Dispensing Head, Blk,P0053 Coffee Dipenser Body, P0053 Cover, Rear Coffee Dispenser Display, Front Plate Assy SPECCHIATO FRONT PANEL SUPPORT P0053/C LED Display Display Support, Black SCREW PT TORX 3X10 WN 1411 GALVANIZ
KIT SPARES CPU P0053/C+FAUCET BOARD 3SEN with part # 21 tab
#N/A #N/A #N/A 140328059 #N/A #N/A #N/A #N/A 129911402

20000652

CPU, Assy Brow Support, Black Support, Adjustment Knob, SBS O-ring, Metric 0040-20, EPDM Spring, Adjustment Dial, SBS Dispensing Shaft, SBS Coffee Dispensing Chute O-Ring, Silicone, 0060-15 Clip, Hairpin, Teflon Tube Tube, Teflon 2X4 L+125 MM Assy O-Ring, Silicone, 2015 SCREW TORX T10 3,5X12 UNI9786 GALVANIZED Fast Lock Connection Tube, Teflon, Insert Blk P0049 Motor, Drip Tray, (Mobile) Guide, Drip Tray Microswitch, Drip Tray Wheel, Drip Tray Support,Blk INSERT FOR ADJUSTMENT TRAY WHEEL P124 FIXING PLATE FOR FEEDING SCREW P124 Gear, Mobile Tray Support Port,Lower D-Tray Blk MOBILE DRIP TRAY GEARS SHAFT P124 Grate, Drip Tray Silver Float, Drip Tray, Odea Drip Tray, Talea Ring + Support, Drip Tray Support Cover, Drip Tray Silve Black Sensor for Board Support Pcb, Touch Sensor, Drip Tray Black Cover, Cables Screw, TCB, Torx, 3.5x8.5
UP TO S/N 9006SA40281741 FROM S/N 9006SA40281742

12000450

11000586
Rev. 01-09/11/06 Brew Group Rev.02 2
SUP032BR Talea Ring Plus E74104 Rev.01 Cod 10001550 Cover, Upper Steam Tube, Chrom Cover, Lower Steam Tube, Chrom Screw, M3x12, Torx, Uni 9786 Steam Tube Assy, P0049 Handgrip, Steam Wand Internal Tube, Pannarello Cover, Pannarello, SS Water Connection, Milk Island Tube, Silicone, D=8x10 O-Ring, Silicone, 2018 Connector,Valve P0054, Blk Spring,Cream Adjustment, Valve Insert,Safety Valve, P0054 Oetiker clip D=9 Connector,Blk O-ring, 108, FDA, 70 SH Connector, Faucet Body Silicone Tube 4,2X8,2 O-ring, Or=2012 Faucet Body, Brass
KIT SPARES CPU P0053/C+FAUCET BOARD 3SEN with part #13 tab 22
11004134 #N/A #N/A 189428600 #N/A 11001365 #N/A JS01022 NV11000651 #N/A 11005096 #N/A #N/A #N/A
PCB,Valve, Stm/Water V1-V5 Spring, Fork, Faucet P0049 Faucet, Tea/Brass, P0049 Faucet Shaft Assy Tube Clamp, Oetiker Straight Connector, Faucet Bod SUPPORT FOR BOILER-FAUCET-VALVE P0049 Thermostat, 175o, Sirius THERMOSTATES SPRING FOR BOILER Boiler Assy, 120V Temp Sensor, L=280mm Casing Assy, Blowdown Valve Connector Assy, Blowdown Valve Coil Assy, Blowdown Valve Powerfilter, 120V Spring, Faucet P0049 Fitting, 90o, Pump Inlet Steel Bracket, Pump Support Connector, 90o, Pump Outlet Pump Support, Black 2POLES CONNECTOR PUMP P0049 UL 120V O-Ring, Epdm, 2031 Pump, Ulka, 120V, 60Hz Tube, Silicone, 5x10, L=156 Turbine Assy 6-Pole Connector, Flowmeter Board, Water Level Sensor BLACK TURBINE SUPPORT/V2 P0049 Screw, M4x8, Uni 8112, Tcb Screw, M5X30,UNI,7688,ZNP Spring Clip, Valve P0049 screw TORX TCB 3,5X9,5 BLACK SCREW PT TORX 3X10 WN 1411 GALVANIZ Faucet Assembly WITH PART. N16-17-19-20-22-23-24-26 Assy,Valve, Blowdown, P0049 WITH PART. N32-33-34-51 ALUM.BOILER P0053 120V ASSY.
UP TO S/N 9006SA40281741 FROM TO 9006SA40281742

11001332 11001751

11005668

11003670

U143.016 129912702

11005617

Rev. 01-09/11/06 Brew Group Rev.02 3
SUP032BR Talea Ring Plus E74104 Rev.01 Cod 10001550 Worm Gear, Grinder, 5P/7P Support,Upper Grinder O-Ring, Metric, Epdm, 0530-15 Grinder Burr, Ceramic, Sirius Pin,Steel M4-M6 LOWER GRINDER SUPPORT COFFEEGRINDER Bearing, Axial EKKO 342.35252 Felt Ring,45,4x39,4x4 Preground Chute Gasket, Dosing Chamber Gear, Grinder Motor MOTOR COFFEEGRINDER/V3.1 DOMEL ASSY 120V CAP FOR WORM SCREW MC/V3 CENTRING PANELVIT TCB SCREW 3,5X25 D.7505 ZN Bushing Insulator,Grinder Mot. Motor, Coffeegrinder/Assy 120V Screw, M3.5x18, Din 7505, Zinc UPPER GEAR SUPPORT COFFEEGRINDER P124 BLACK INSERT FOR COFFEE GRINDER P0049 COFFEE GRINDING ADJUSTMENT GEAR P0049 GRINDER REGULATION SPRING P124 LOWER GEAR SUPPORT COFFEEGRINDER P124 SWITCH+SOCKET POWER CABL.SUPP.SMART CRINKLE WASHER 21,8X15,8X0,2 RADIAL BEARING 61900.2RS1 Electronic Board, With Sensor Support,Rubber Blk,Coff Grind Sensor Support, Grinder Motor GALVAN.FLAT WASH.DI=4,3 DE=14 SP=1,5 Nut, Self-Lock, M4 Din 982 Cover, Grinder, (Soundproof) 5-Pole Connector General Motory Assy

127473603 #N/A #N/A #N/A 80001013 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A 149199050 #N/A 11005658 11005606

149198350

149214800 129661702

128381800 123030200

128381902
Rev. 01-09/11/06 Brew Group Rev.02 4
SUP032BR Talea Ring Plus E74104 Rev.01 Cod 10001550 Boiler Pin Assy Cap, For Pin, For Boiler P119 O-Ring, Silicone, 2015 O-Ring, Silicone, 0060-20 Clip, Hairpin, Teflon Tube Pin, For Boiler P119 O-Ring, Silicone, 0090-20 O-Ring, Silicone, 0050-20 Switch, Brew/Dump, Magic Kit, Gears, Ratiomotor Washer, Brew Drive Motor, Myla SINTERED BUSH FOR MOTOR Washer, Vspressso, D=5 Antivibration, BrewDrive Motor Ratiomotor Assy BLACK MICROSWITCH SUPPORT DUMP BOX P0049 Fitting,90,plastic Fitting, 90,Plastic O-Ring,Metric,Silicone,0070-20 Cover, Mounting Plate, Blk Black Cover Vain Boiler P0049 Board, Water Level Sensor Reed Sensor, 100-120V Screw K, 35x12 Win1423 Galv. Brew Group, 8 Gram, Primea SEE TAB. COD. EXP. E90042
11003825 NM01035 NM01057 NE91611320 #N/A 11005213 #N/A 11002145

9121.046

11001331
Rev. 01-09/11/06 Brew Group Rev.02 5
Brew Group Talea Ring Plus Esp. E90042 Rev.02 Cod: 11002145 SVS Valve, Primea Touch Plus SS.SCREW AUT.TCB 2,9X19 DIN 7981 C Tube For Piston Brew Group Black Counter Piston Brew Grou O-Ring, Silicone, 0320-40 Filter Screen, Brew Unit Spare Sleeve Unit Black WATER INLET SLEEVE BLACK O-Ring, Epdm, 2025 BLACK REAR PLATE FOR BREW UNIT SMART Screw, M2.9x9.5, Din 7982 Bale, Brew Group, Smart Drilled Black For Unit Grey ELBOW SHAFT FOR UNIT BLACK BLACK COUPLING PLATE BREW UNIT SMART BLACK HOPPER DOSER BREW UNIT SMART1 SCREW AUT.TCB 2,9X9,5 DIN 7981 C BLACK HOPPER BLOCKING PLATE UNIT SMART SPRING HOPPER SMART GROUP SCRAPER FOR BREW UNIT SMART SPRING FOR UNIT SCRAPER SPRING FOR PISTON BUSH FOR PISTON NEUTRAL BLACK INTEGRAL PISTON UNIT P124 8GR.ASS BLACK COFFEE CONTAINER UNIT 8GR.P124 ASS BLACK CONNECTING ROD FOR UNIT P124 8GR. FRONT PLATE FOR BREW UNIT SMART SS.SCREW AUT.TCB 3,5X19 DIN 7981 C Brew Group, 8 Gram, Primea
#N/A NM20000440 #N/A NM02007 #N/A 9161094150 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A 11002145 U109.027