2-3. CDMA Section

2-3-1. Receiver
Low Noise Amplifier(U1000) The low noise amplifier(It is included FC7510: U1000) amplifies a weak signal received from the base station to obtain the optimum signal level.
RF Band Pass Filter(F1000) The RF BPF(F1000) passes only a specific frequency(881.4912.5 MHz) from the signal received from the mobile station. The bandwidth is 25 MHz.
Voltage Controlled Oscillator(VCO1000) The VCO(VCO1000) generates the signal having center frequency 1715 ~ 1788MHz frequency range with the voltage control. The PLL in RTR6300 controls this signal.
Frequency Synthesizer Circuit The PLL(Phased Locked Loop) block consists of VC-TCXO(TCX1001), PLL in RTR6300 and VCO(VCO1000). Input reference frequency is generated at VC-TCXO(TCX1001) and the RF local signal is generated at VCO. PLL compares the two signals and generates the desired signal with a preprogrammed counter which controls voltage.
VC-TCXO(TCX1001) The VC-TCXO (TCX1001) is a reference source of the frequency synthesizer. It provides 19.2MHz reference frequency to PLL-IC. It is a voltage controlled temperature compensated crystal oscillator having 19.2MHz 2.5ppm frequency stability over all useful temperature range. A correct frequency tuning is made by the control voltage.

2-3-2. Transmitter

Antenna(ANT1) Antenna(ANT1) sends signal to the base station and receives the signal from the base station. It is a multi-band Antenna and covers PCS band, CDMA band DCS band, GSM Tx band and GPS band. RF Switch(U1201) It(U1201) is used to switch the PCS path, the CDMA path the GPS path and the GSM path, The RF signal pass through PCS path when PCS_SW is high. PCS_SW, CDMA_SW, GPS_SW and GSM_SW are digital signals from MSM6500 via Decoder(U1200). Duplexer(DUF1107) Duplexer(DUF1107) allows Rx frequency range(881.49 12.5 MHz) and Tx frequency range (836.49 12.5 MHz) from the antenna to pass through LNA. It also matches LNA input in receiving part and PAM(PAM1104:CX77105) output in transmitter part with the antenna. Power Amp(PAM1104) Power amplifier module(PAM1104:CX77105) amplifies signal to be sent to the base station through the antenna. RF Band Pass Filter(Tx RF SAW Filter) The RF BPF(F901) pass only specific frequency(836.49 12.5MHz) to send it to power amp(U903:CX77105). Direct Conversion Transmitter(U1102) The Direct Conversion Transmitter(U1102: RTR6300) allows the signal to be inputted to the power amp(PAM1103) as a specified level from I, Q base band signals.
Automatic Gain Control Amp The TX AGC amp in RTR6300 controls gain of AGC to deliver power level to be needed at Driver amp. Its control voltage varies from 0.2V to 2.5V.

2-4. GSM/DCS Section

2-4-1. Receiver
Low Noise Amplifier(U1102) The low noise amplifier(It is included in RTR6300 : U1102) amplifies a weak signal received from the base station to obtain the optimum signal level.

2-6. PDA PART

The PDA logic part consists of power supply part, MPU & memory part, LCD part, audio part and all the peripherals.

2-6-1. POWER SUPPLY

When the battery is inserted to the handset, VBAT makes VCC_BATT, VCORE14, VPLL13, VSRAM11 via U405(MAX1587) which is a CPU voltage VCC30 via U405(MAX1587) which is CPU & peripheral voltage, VCC28 via U414(MIC5219-2.8BML) which is a DPRAM voltage, VLCD33 via U413(MIC2211-SSBML) which is a LCD logic voltage, VBT30 via U416(MIC2211-PPBML) which is a Buletooth voltage. VBAIS30 via U416(MIC2211-PPBML) which is a MIC vias voltage. VBAT33 via U413MIC2211-SSBML) which is a backup battery charging voltage, VSD30 via U410(MIC2212) which is a SD-Card voltage. VCC30 makes VCC18 via U412(MIC2211-JGBML) which is a M-DOC voltage, VDD30 makes VDD18 via U411(MIC2211-JGBML) which is a SDRAM voltage, VLCD33 makes AVDD5V, VON, VOFF via U1000(MAX1779) which is LCD pannel voltage.

Backup Battery

The SPH-i830 has a back-up battery(ML1220) that stores data of SDRAM when the battery removed or becomes low battery state that is below 3.1V. The low battery state is checked by voltage detector or R3111Q311C(U400). If the battery level is below 3.1V, nPOWER_FAIL signal is asserted. Then the backup DC/DC converter(U405, MAX1676) output path is connected to VDD30 which is MPU, SDRAM voltage. Backup battery supply main voltage or VDD30. If backup battery voltage is below 2V, discharging path is disabled.
2-6-2. MPU & Memory part
MCP(UCP201:LVPXA272FC5520) ARM Architecture Built in Memory Controller, LCD Controller, AC97 Controller and MMC Controller Intel PXA272 processor with 64 Mbytes of Intel StrataFlash memory Flash memory is used to store the PDA executable program and necessary data files. Clock and Power Controllers It has a variety of different system peripherals and controls all the peripheral circuitry.
NAND FLASH Memory(UME301:MD4832D512) High capacity: single die - 512Mbit (64MB) Nand Flash memory is used to user data files. SDRAM Memory(UME305:K4S51323PF) Samsung CMOS technology 64MByte capacity Mobile Synchronous Dynamic RAM. It is used as a application program execution space, temporary data space to store the internal flag information, timer data, and user data files. DPRAM Memory(UME300:IDT70P248L55) 4Kx16bit dual port RAM It is accessed by Phone and PDA, but not accessed simultaneously. Generally, Instructions and data used by Phone and PDA are stored.

2-6-3. LCD part

PXA272 has a LCD controller. LCD module a transflective type color active matrix TFT It is composed of a TFT LCD module(TFT LCD panel, driver ICs), a Backlight unit and a touch screen panel. The resolution of 2.8inch contains 240x320 pixels and can display 65K colors.

2-6-4. Audio part

PDA plays audio files via WM9712 and the voice of the phone is connected to the WM9712. WM9712(U400) The WM9712 is a high quality stereo codec with an integrated touch screen controller. Interfaced to PXA272 via AC'97 protocol. AC'97 Rev 2.2 specification headphone outputs a complete 4-wire touch screen controller

2-6-5. Wireless Part

Bluetooth Antenna Antenna receives signal from AP(Access Point) or other devices. It is a ISM(industrial, Scientific, Medical frequencies) Band Antenna that covers only 2.4 GHz. Module The Bluetooth Module which uses CSR's BC02-Audio is manufactured by SEMCO. It only supports 802.15 Specification(Bluetooth Specification 1.1) and communicates with CPU through UART Interface. The data throughput is up to 1 Mbps in the abstractly but typically supports 723 / 57.6 Kbps in an asynchronous mode and 432.6 kbps in a synchronous mode. Modulation method is FHSS(Frequency hopping spread spectrum) and it hops 1600 times a second. Its channel spacing is 1MHz and bandwidth is 1MHz.
2-6-6. All the Peripherals
Memory card The MultiMediaCard Controller on the Intel PXA272 can communicate with either: a MultiMediaCard (MMC) a Secure Digital (SD) Memory Card a Secure Digital I/O (SDIO) Card IrDA(U200:HSDL-3003) IrDA Data Compliant 115.2kbit/s with Remote Control Transmission Infrared Transceiver. a small form factor single enhanced infrared transceiver module that provides the combination of interface between logic and IR signals for through-air, serial, half-duplex IR data link, and IR remote control transmission operating at 940nm for universal remote control applications. USB There is a USB Client in the Phone part and PDA part each. The USB signals are switched to the interface connector via MUX(U604, MAX4636). The USB interface of the Phone part is used for downloading and data service. The USB of the PDA part is used for downloading user files and application programs by Active Sync to PC. UART There is a UART port in the Phone part and PDA part each. The UART signals are switched to the via the MUX(U601, MAX4684). KEYPAD For user interface, a keypad is used for function. For key recognition, a key matrix is set up using signals KBC_(0)~(6) and KBR_(0)~(7) of the PXA272.

NAM Programming

NAM SETTING FLOW:
LCD Display Service Menu Home SID (4139) Home NID (65535) MCC (310) MNC (00) ACCOLC Enter the number Enter the number Enter the number Enter the number Enter the number Toggle Yes or No by press and select by press enter key Toggle Yes or No by press and select by press enter key Toggle Yes or No by press and select by press enter key Cannot change Cannot change This screen allows you to view and modify the home system ID (SID). This screen allows you to view and modify the home Network ID (NID). The MCC screen allows you to view and modify the mobile country code. The MNC screen allows you to view and modify the mobile network code. The ACCOLC screen allows you to view and modify the access overload class. Home SID Registration. change Function

CDMA Home Reg (YES)

CDMA fSID Reg (YES)
Foreign SID Registration.

CDMA fNID Reg (YES)

Foreign NID Registration.
ESN (Hexa Number) P_REV (6)
Electronic Serial Number of the phone is displayed. Protocol Revision of the phone is displayed.

VOCODER (EVRC)

Toggle the item by press and select by press enter key
Select vocoder option between EVRC and 13K Vocoder.

SCM (00101010)

Cannot change
Station Class Mark of the phone is displayed.

Lock Code

Enter the number
This screen allows you to view and modify the lock code. This screen allows you to view and modify the slotted mode.

SLOT MODE (YES)

Toggle Yes or No by press and select by press enter key

SLOT CYCLE INDEX (2)

This screen allows you to view and modify the slot cycle index. 4-2

5. Product Support Tools

5-1. General
IMPORTANT INFORMATION Purpose
The Product Support Tool (PST) offers you the ability to interface with the SAMSUNG mobile phone using a PC. With this tool you can program the phones network system requirements and functionality, data, and download software upgrades. This document supports UniPST(Universal Product Support Tool).
EQUIPMENT REQUIRED Make sure you have the following equipment setup: 1. Minimum PC configuration: 586 CPU, 64MB RAM, Windows2000/XP and above, 5MB of disk space free for software upgrade. 2. PST Software with appropriate cable (USB Cable for SAMSUNG mobile phone). 3. USB Port. 4. Power Supply (4.3 V) or Battery.

Performing Software Upgrade HW version : 1.2 SW version : ZH21 or later Please use SamsungPST FW Setup1.0.002_MSI 2ndEdition and PSTI830.dll ( Universal PST For Sprint 1.723 - [SCH-i830] or higher) When the user downloads the S/W on the SCH-i830 device the user may use external power removing battery from the device or a fully charged battery. Install USB drivers (use MCCI USB driver version 4.16) For data call test and downloading new s/w, install two setup programs which located in the / USB_Driver directory. A. B. SAMSUNG USB Modem driver_V4.16.zip (Phone USB) MSASYNC.EXE (Active sync 4.1, it also install PDA USB driver)
FIG 1. Active sync connection setting From fig 1. Showing above is the correct configuration of active sync for data call and downloading. When the user downloads the s/w on the i830 device the user may use travel charger, fully charged battery or JIG ( refer to 15) connections.
IMPORTANT : Please proceed following steps prior to Download the PRL and ERI Read/Write the settings Download software (.img)
1. Start -> Settings -> Choose "System tab" -> Data Connection 2. Choose "As the modem through USB". Press "ok": USB path will be changed to phone. 3. Now the hand set is ready to download, please follow the steps below. A. Make sure that USB DATA cable plugged into the user PC properly. B. Run the "UniPst" and select SCH-i830. Press "RUN". C. Choose "Download Mode" which is below main menu. D. Go to "Setup" > "COMM Setting". Make sure that correct COM port is selected. E. Go to "File" > "Open Bin" to locate image file (For example, i830WM5.1.2S.ZH21.img) to download. D. Click "Phone + PDA" icon to download both phone and PDA images. (If the user need to download PHONE ONLY or PDA ONLY the user must pick the re-set hole for more than 3 seconds.) E. Select "OK" in next below message "Is Current CDMA USB Modem Port X ?" F. Select "OK" again, and then do hard reset the phone as described in the dialog window. G. After downloading is complete, please verify handset. Press Start Menu and go to "Start" >"Settings" > "System" tab > "Phone Info" to make sure that appropriate PDA and phone versions are shown.
Trouble shooting for the following message: Error in changing USB DM 1. TEST MODE ( # 0 * 0 ) 2. Press 001 3. Press 100 4. Change Port map to U1_HFK USB_DS by using up, down arrow 5. Press enter 6. Press 002 7. Change USB path as the modem through USB by (Start -> Settings -> Choose "System tab" -> Data Connection)
7. Flow Chart of TroubleShooting

7-1. Logic Section

7-1-1. Power On PDA Part

Insert Power

R904 R905 V_IN 9PF COSC900 CC4V-TSLEEP_XTAL_IN TCXO TCXO_EN TCXO_OUT R913 GSM_PA_PWR_CTL_REF < USIM SOCKET > R1 D901 USB_OE_N USB_DAT USB_SEO PHONE_D+ PHONE_DTP903 C905 TP904 R910 C903 9PF VBAT_PM6650 R906 TP900 TP901 TP902

L902 L903

R907 PS_HOLD

R909 R911 R912

AMUX_OUT

PS_HOLD IF_CON_SENSE

SIM900

VREG_USIM

G G G G 8 7

V_IN R921

C910 V_IN

C911 C912

C919 C920

C921 C922

C914 C915

C916 C917

R915 nPMIC_RESET USIM_IO USIM_CLK USIM_RST RSIM_IO SIM_CLK SIM_RST PM_SBDT PM_SBCK PM_SBST PM_INT_N

C928 R919

GND 85
TR903 C931 C930 C932 C933 C934

VCC_BATT C939

U902 1NC PS_HOLD_P 2 nBATT_FAULT INA GND INB OUTY VCC U901 PHONE_ON 2 IN 3 GND PS_HOLD 4 OUT C940 VCC5

VREG_MSMP C864

U803 nMSM_RST 2 nPMIC_RESET R862

OUTY 4

RESIN_N

PWR_CAP_0_GPIO5

PWR_CAP_1_GPIO6

PWR_CAP_2_GPIO7

PWR_CAP_3_GPIO8

TXTAL_OUT

TXTAL_IN

PWR_OUT D20

OSC200

7-1-2. LCD Working

LCD Display OK?

9pin in U413 = High?

3pin in U413 = High?

Change PBA

YES YES

Change U413

4pin in U1000 = High?
Check LCD TOP FPCB, Slide FPCB
1pin in D1001 = 4~5V? 2pin in D1003 = 17~18V? 1pin in D1002 = -8~9V?
Check U1000 & neighboring circuits
Check LCD TOP FPCB & LCD

Back Light OK?

4,5pin in U1001 = High?

1pin in U1001

Check U1001 & neighboring circuits

= 12V?

TSP OK?
When touch screen 46pin in U900 = High?
Check LCD TOP FPCB , Slide FPCB & LCD
Check ZD603,UCD500 & neighboring circuits 7-8

VBAT33

VLCD33
UVIN nCHARGE_OFF LCD_ON 2 ENENCBYP 5 N/C VOUT1 0
VOUTN/C 8 N/C 7 GND 6 C453 C454

GND GND GND GND GND GND

V_LCD33

R1000 L1000

R1001 R1002 VCC30_SUB C1004 L1002 U_RDY TGND 16 C1006 U5 PWM_BLED_SUB CSW VIN CTRL VOUT GND FB 3 R1005 C1011 R1006 LEDLED+ RFB LX 3 INTG PGND 4 IN SUPP 5 GND DRVP 6 REF SUPN 7 FBP DRVN 8 FBN _SHDN MAX1779EUE DC3 C1007 C1005 R1003

2 D1001

C1014 C1015 R1008

2 VON VOFF

VON15 C1016 C1017 VOFF9 R1009 100K
40 HPGND HPOUTR 41 HPOUTR 42 AGNDHPVDD 44 GPIOGPIO2/IRQ 46 GPIO3/PENDOWN 47 GPIO4/ADA/MASK 48 GPIO5/SPDIF_OUT 49 GND 50 GND 51 GND
MIC2 MIC1 PHONE PCBEEP TPGND Y-/BL X-/TL Y+/TR

22 RTSMY TSMX TSPY TSPX R518 C531 TA529 C524
PHONE_MIC_JMP MIC PHONE_SPK

UCD500

PEN_DETECT

X+/BR 14 TPVDD 13

ZD603 TSPX TSMX 34 IO 6 CLOCK NC 5 TSPY TSMY

SIM VCC

7-1-3. Audio Working

Speaker Working

Operate Speaker
SPK Contact Pad in Side FPCB Signal ON?

Change SPK

A3,C3 pin in U505, A3,C3 pin in U506

Signal ON?

Check Side FPCB & HDC 600
2,10pin in U503 Signal ON?
Check U505,U506 & Neighboring Circuits

4,8pin in U503 = High

35,36pin in UCD500 Signal ON?

Change U503

Check UCD500 & Neighboring Circuits

HDC600

KBR(0) KBC(0) SPEAKER_R+ SPEAKER_RMOTOR_R
KBR(1) KBC(1) SPEAKER_L+ SPEAKER_LMOTOR_L

ZD602 RCVOUT LED_G 3

HPOUTL LED_R LED_B

Reciever Working

Operate Reciever
RCV Soldering Pad in LCD TIP FPCB Signal ON?

Change RCV

37,39pin in UDC500 Signal ON?
Check LCD TOP FPCB, Slide FPCB & ZD602
Check UDC500 & Neighboring Circuits

Mic Working

Operate MIC

4pin in U507 Signal ON?

Check D501 & Change MIC

5pin in U507 Signal ON?

1pin in U507 = Low?
Check U508 & Neighboring Circuits

Change U507

3pin in U501 Signal ON?

4pin in U501 = High?

Change U501
Hands-Free Stereo Headset Working
Hands-Free Stereo Headset
SPK , MIC & Button All NG?

10pin in U416 = High?

2pin in U416 = High?
Check EAR500 & Neighboring Circuits

Change U416

Button NG?

1pin in U508 = High?

Check EAR500, U508 & Neighboring Circuits

MIC NG?

6pin in U507 Signal ON?

5pin in U507

7pin in U508 = High?
Check U501, U508 & Neighboring Circuits

SPK NG?

39,41pin in UDC500 Signal ON?

10pin in U501 Signal ON?

Check UDC500, U501 & Neighboring Circuits 7-14

7-1-4. KEY Working

Press KEY
Volume key or Voice Recoding key NG?

Break a Side Key FPCB

Change Side Key FPCB
Check HDC600,ZD604 & KEY Metrix connection circuits
Application key or Navigation key NG?
Break a LCD Top FPCB or Slide FPCB
Change LCD Top FPCB or Slide FPCB
Check ZD601 & KEY Metrix connection circuits
Qwerty key or Voice Signal key NG?
Check ZD718,ZD719,ZD720 & KEY Metrix connection circuits
Power key or Lock key NG?

Break a SW700

Change SW700

Check SW700

& neighboring circuits

Yes No L1113 >= -75dBm Resolder F1104

Check U1102

7-4-2. GSM Transmitter

TX ON (5 Level)

Yes C1231 <= 30dBm Yes Resolder C1208, U1201
No C1221 <= 25dBm Yes Check U1202 pin4 = H, pin6 = L
Yes Change or Resolder U1202

No C1233 <= 20dBm Yes

Check SPDT control circuit

Resolder

DUF1200
No R1102 <= 1.0V No R1113 = H Yes Resolder or Change PAM1101

No Yes Check U1102

Check +VBATT or PAM control signal

7-4-3. DCS Receiver

Yes C1221 >= -65dBm No Check U1202 pin4 = H, pin6= L Yes Yes No C1144 >= -70dBm Resolder DUF1200 Resoder U1202 No Check SPDT control circuit
Yes No L1106 >= -75dBm Resolder F1100

7-4-4. DCS Transmitter

Yes C1231 <= 25dBm Yes Resolder C1208, U1201
No C1221 <= 22dBm Yes Check U1202 pin4 = H, pin6 = L

No C1232 <= 20dBm Yes

No R1109 <= 1.0V No R1113 = H Yes Resolder or Change PAM1101
8. Exploded View/Disassembly and Assembly Instructions

8-1. Exploded View

QFU01 QSC01
QFR01 QKP02 QMI03 QME03 QLC01 QME02 QMP02 QCR06 QVO01 QCR25 QCK01 QSC14 QKP01

QMI01 QME01 QMP01

QSH01 QCR07

QVK01 QCR06 QAN02

QCR06 QAN01 QST01
QRE01 QRF03 QCR39 QSC13 QRF01 QSC08 QSC07 QBA01 QIF01
Exploded View/Disassembly and Assembly Instructions

8-2. Parts list

Location NO.
QAN01 QAN02 QAN06 QBA01 QBA02 QCK01 QCR06 QCR06 QCR07 QCR17 QCR25 QCR39 QFL01 QFR01 QFU01 QIF01 QKP01 QKP02 QLC01 QME01 QME02 QME03 QME05 QMI01 QMI03 QMP01 QMP02 QRE01 QRF01 QRF03 QSC01 QSC07 QSC08 QSC13 QSC14 QSH01 QST01 QVK01 QVO01

Description

ANTENNA-SCHI730 BLACK INTENNA-SCHI830 RMO-ANT CONTACT RUBBER BATTERY-1700MAH,ENG,MGRAY,M BATTERY-1100MAH,ENG,MGRAY,M PMO-SWITCH KEY SCREW-MACHINE SCREW-MACHINE SCREW-MACHINE SCREW-MACHINE SCREW-MACHINE SCREW-MACHINE ASSY MEC-SLIDE LOWER ASSY MEC-FRONT COVER ASSY CASE-SLIDE UPPER(SPRINT) RMO-IF COVER ASSY MEC-KEY QWERTY ASSY KEYPAD-SUB(SPR/SIL) LCD-SCHI730 LCD UNIT-METAL DOME(MAIN) UNIT-METAL DOME(SUB) UNIT-TOP FPC ASSY MEA-SLID FPCB KIT MICROPHONE-ASSY RMO-MIC RUBBER PBA MAIN-SCHI830 SPRINT PBA MAIN-SCHI830 SPRINT SUB ASSY MEC-REAR COVER RMO-RF COVER PMO-EAR COVER RMO-RUBBER SD DOOR RMO-SCREW CAP BOTTOM(L) RMO-SCREW CAP BOTTOM(R) RMO-RUBBER SCREW CAP UP RMO-RUBBER FRONT 2 ASSY MEC-SHIELD CAN ASSY MEC-STYLUS UNIT-SIDE FPCB ASSY MEC-VOLUME KEY

SEC CODE

GH42-00540A GH42-00643A GH73-03121A GH43-02518A GH43-02529A GH72-20053A 6001-001155 6001-001155 6001-001691 6001-001460 6001-001893 6001-001606 GH75-04632A GH75-06385A GH98-01434A GH73-04597A GH75-06486A GH98-01437A GH07-00574A GH59-02233A GH59-02177A GH59-02458A GH97-05290A GH30-00132A GH73-03120A GH92-02816A GH92-02829A GH75-06386A GH73-04596A GH72-20918A GH73-04860A GH73-03372A GH73-03373A GH73-04247A GH73-05101A GH75-07290A GH75-06210A GH59-02295A GH75-06488A
PLUG-CONVERSION PLUG-CONVERSION ANTENNA-CHIP BAG PE BAG PE BAG PE CBF INTERFACE-PC DATA LINK CAB CHARGER-TRAVER CHARGER S/W CD-SCH-I830 MPROJECTOR 2.0 UNIT-EARPHONE UNIT-SIM CARD LABEL(P)-GUIDE(SPRINT) LABEL(P)-WATER SOAK LABEL-MAIN(SPR) LABEL(R)-MAIN(SER CKD) MANUAL USERS-NOA ENGLISH MANUAL USERS-NOA ENGLISH MANUAL USERS-NOA ENGLISH BOX-UNIT(SPR) CUSHION-CASE MAIN(VER) RMO-RUBBER REAR 4 MPR-TAPE LCD 1 MPR-TAPE LCD 3 MPR-BOHO VINYL LCD 1 MPR-VINYL BOHO OTA(SPRINT) MPR-GASKET FRONT 1 MPR-GASKET FRONT 2 MPR-TAPE FRONT MPR-FLEX SUPPRESSOR MPR-BOHO VINYL KEY MPR-FRONT GASKET 3 MPR-PCB GASKET 2 MPR-TAPE MAIN ACTURATOR MPR-TAPE SUB ACTURATOR B MPR-TAPE SUB ACTURATOR G MPR-TAPE MAIN BASE MPR-TAPE EAR
3721-001057 3721-001077 4202-001040 6902-000297 6902-000461 6902-000643 GH39-00567A GH44-00933A GH46-00311A GH59-01538A GH59-03667A GH68-02023A GH68-02026A GH68-06548B GH68-10705D GH68-11558A GH68-12202A GH68-12260A GH69-02742B GH69-03365A GH73-05481A GH74-13066A GH74-13068A GH74-13069A GH74-13264B GH74-15356A GH74-15357A GH74-15360A GH74-15939A GH74-16032A GH74-16583A GH74-16585A GH74-17682A GH74-17683A GH74-17684A GH74-17686A GH74-19716A
8-3. DM Cable(GH39-00272A)

8-4. Test JiG

8-5. RF Cable(GH39-00105A)
8-6. Test Jig Cable(GH39-00122A)

8-7. Disassembly

lift PBA from the right HOOK

lift BT,MIC

separate FPCB
IF cover volume key switch key

screw cap

ear cover

pull FPCB from connector

unfold connector lock
1.remove screw caps and unscrew 4 points 2.separate REAR from SET (start from lower side HOOK) 3.separate side key,switch key,ear cover and IF cover from SET Caution 1. be careful not to break HOOK or bend REAR 2. be careful not to leave finger print on the antenna contact

GH71-00734A 4302-001176 3711-006035 2203-005482 2203-006646 2203-006646 2203-000995 2203-006646 2203-006646 2203-000233 2203-002443 2203-000233 2203-001598 2203-000233 2203-005664 2203-001598 2203-005382 2203-000438 2203-006646 2203-005061 2203-005065 2203-005382 2203-006307 2203-000438 2203-006307 2203-005482 2203-005552 2203-000438 2203-006307 2203-000438 2203-005482 2203-005061 2203-006307 2203-006307 2203-000233 2203-006646 2203-000233 2203-005061 2203-005552 2203-000438 2203-006646 2203-000233 2203-006646 2203-000233 2203-005482 2203-005482 2203-005736 2203-000995 2203-005061 2203-000995

STATUS

SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA SA

Electrical Parts List

C1032 C1033 C1034 C1035 C1036 C1037 C1038 C1039 C1040 C1042 C1043 C1044 C1045 C1046 C1047 C1048 C1049 C1050 C1051 C1052 C1053 C1101 C1102 C1103 C1104 C1105 C1106 C1107 C1108 C1109 C1110 C1112 C1114 C1115 C1116 C1117 C1118 C1119 C1120 C1121 C1123 C1124 C1125 C1126 C1127 C1128 C1129 C1130 C1131 C1133
C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-FILM,SMD-PPS C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP C-CER,CHIP 10-2
2203-000995 2203-000278 2203-005482 2203-005482 2203-006646 2203-005061 2203-000995 2203-005552 2203-005393 2203-000254 2203-000254 2203-000254 2203-005061 2203-000585 2301-001213 2203-001124 2203-005482 2203-006201 2203-000254 2203-000254 2203-000233 2203-000438 2203-005482 2203-005736 2203-005736 2203-005383 2203-005446 2203-000438 2203-000311 2203-001072 2203-000609 2203-000812 2203-000254 2203-005503 2203-005234 2203-006194 2203-006194 2203-006121 2203-006379 2203-002759 2203-006379 2203-006423 2203-000233 2203-006379 2203-000233 2203-001178 2203-000233 2203-005736 2203-005806 2203-005682

2203-000254 2203-005061 2203-006562 2203-005483 2203-006194 2203-001652 2203-003054 2203-003054 2203-005482 2203-000233 2203-005482 2203-006423 2203-006208 2203-006208 2203-005482 2203-000278 2203-006208 2203-006208 2203-006208 2203-000278 2203-006562 2203-000278 2203-006201 2203-000278 2203-006201 2203-006201 2203-000278 2203-005482 2203-000812 2203-000812 2203-000254 2203-005482 2203-005482 2203-005482 2203-005482 2203-005482 2203-006208 2203-005482 2203-006646 2203-005482 2203-005061 2203-005061 2203-006562 3709-001251 3711-005394 4709-001361 4709-001361 0402-001329 0404-001152 0404-001152
D1003 D1101 D400 D401 D500 D501 D600 D715 D716 D717 D723 D724 D901 DUF1107 DUF1200 EAR500 F1000 F1001 F1002 F1100 F1101 F1103 F1104 F1105 F600 F601 HDC600 IFC703 L1000 L1000 L1001 L1001 L1002 L1002 L1003 L1004 L1005 L1006 L1007 L1008 L1009 L1010 L1011 L1012 L1013 L1014 L1015 L1016 L1017 L1018
DIODE-SCHOTTKY DIODE-SCHOTTKY DIODE-SCHOTTKY DIODE-SCHOTTKY DIODE-TVS DIODE-TVS DIODE-TVS DIODE-TVS DIODE-TVS DIODE-TVS DIODE-SWITCHING DIODE-TVS DIODE-ARRAY DUPLEXER-SAW DUPLEXER-ASM JACK-EAR PHONE FILTER-SAW FILTER-SAW FILTER-SAW FILTER-SAW FILTER-SAW DUPLEXER-FBAR FILTER-SAW FILTER-SAW FILTER-EMI/ESD FILTER-EMI/ESD HEADER-BOARD TO BOARD SOCKET-INTERFACE INDUCTOR-SMD BEAD-SMD BEAD-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD 10-11
0404-001152 0404-001093 0404-001089 0404-001089 0406-001169 0406-001150 0406-001150 0406-001150 0406-001150 0406-001150 0401-001110 0406-001150 0407-001002 2909-001255 2909-001197 3722-002067 2904-001533 2904-001494 2904-001414 2904-001424 2904-001499 2910-000009 2904-001417 2904-001502 2901-001294 2901-001294 3711-005578 3710-001732 2703-002829 3301-001729 3301-001336 3301-001729 2703-002200 2703-002856 2703-002204 2703-002205 2703-002268 2703-002268 2703-002205 2703-002207 2703-002314 2703-002176 2703-002200 2703-002176 2703-002365 2703-002281 2703-002309 2703-002176 2703-002198 2703-001737
L1019 L1020 L1021 L1022 L1102 L1105 L1106 L1107 L1109 L1110 L1111 L1112 L1113 L1114 L1116 L1117 L1118 L1119 L1121 L1122 L1200 L1202 L1203 L1205 L1209 L1211 L200 L400 L401 L402 L403 L500 L501 L502 L503 L600 L800 L900 L901 L902 L903 LED700 LED701 LED702 LED703 LED704 LED705 LED706 LED707 LED708

INDUCTOR-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD BEAD-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD BEAD-SMD INDUCTOR-SMD BEAD-SMD BEAD-SMD BEAD-SMD BEAD-SMD BEAD-SMD BEAD-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD LED LED LED LED LED LED LED LED LED 10-12
2703-002308 3301-001729 2703-002309 2703-001747 3301-001342 2703-002281 2703-002485 3301-001342 2703-002206 2703-002281 3301-001120 2703-002208 2703-002596 2703-002208 2703-001938 2703-002314 2703-001409 2703-002314 2703-002204 2703-002281 3301-001342 2703-001938 2703-002368 2703-002281 2703-001990 3301-001756 3301-001729 2703-002856 2703-002803 3301-001342 2703-002829 3301-001336 3301-001756 3301-001756 3301-001756 3301-001756 3301-001729 2703-001868 2703-001868 2703-002653 2703-002653 0601-001602 0601-001602 0601-001602 0601-001602 0601-001602 0601-001602 0601-001602 0601-001602 0601-001602
LED709 LED710 LED711 LED712 LED713 LED714 MOD600 OSC200 OSC201 OSC500 OSC800 OSC900 PAM1101 PAM1103 PAM1104 R1000 R1000 R1001 R1001 R1002 R1002 R1003 R1003 R1004 R1004 R1005 R1005 R1006 R1006 R1007 R1007 R1008 R1008 R1009 R1009 R1010 R1010 R1011 R1011 R1012 R1012 R1013 R1014 R1014 R1015 R1015 R1016 R1016 R1017 R1018
LED LED LED LED LED LED BLUETOOTH MODULE CRYSTAL-SMD CRYSTAL-SMD CRYSTAL-SMD RESONATOR-CERAMIC CRYSTAL-SMD IC-POWER AMP IC-POWER AMP IC-POWER AMP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP 10-13
0601-001602 0601-001602 0601-001602 0601-001602 0601-001602 0601-001602 4709-001354 2801-003856 2801-004189 2801-004225 2802-001182 2801-003856 1201-002174 1201-001957 1201-001894 2007-001290 2007-007489 2007-000148 2007-001290 2007-000162 2007-000982 2007-007014 2007-007311 2007-007014 2007-007491 2007-000172 2007-000982 2007-000138 2007-000167 2007-000138 2007-007943 2007-000172 2007-007014 2007-000162 2007-001291 2007-000140 2007-000171 2007-000143 2007-007488 2007-000171 2007-001288 2007-008275 2007-000172 2007-007095 2007-000174 2007-007092 2007-003010 2007-003030 2007-007092 2007-000140