SAMSUNG Home Appliance Service
For the latest parts information, please access to our service web site (http://www.e4buyer.com/refrigerator)
SIDE-BY-SIDE REFRIGERATOR
Model: RS20NCSL RS20NCSW RS20NESL RS20NESW

WARNING

IMPORTANT SAFETY NOTICE
The service guide is for service men with adequate backgrounds of electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or dealer cannot be responsible for the interpretation of this information.
SAMSUNG ELECTRONICS Technical Service Guide Copyright 2002
All rights reserved. This service guide may not be reproduced in whole or in part in any form without written permission from the SAMSUNG ELECTRONICS Company.

Contents

1. SAFETY WARNINGS 2. INSTRUCTION 3. INSTALLATION 4. NOMENCLATURE 5. SPECIFICATIONS 6. INTERIOR VIEWS AND DIMENSIONS 7. FREEZING CYCLE AND COOL AIR CIRCULATION ROUTE 8. MECHANICAL DISASSEMBLY 9. FUNCTIONS AND OPERATION 10. CIRCUIT DESCRIPTION 11. DIAGNOSIS AND TROUBLESHOOTING 12. ILLUSTRATED PARTS CATALOGUE APPENDIX (CIRCUIT DIAGRAM) 57

1. SAFETY WARNINGS

Pull the power plug out already for the change or repair of electric parts. Be careful the electric shock. When exchanging the parts, use the correct parts. Check the model name, rating voltage, rating current, running temperature symbols. When troubleshooting, connect firmly the types of harness. Make not to be separated when some power is imposed. Check the traces of water infiltration at the electric parts. If there is a trace of water infiltration, exchange or tape the parts. Check the assemble status of parts after troubleshooting. It should be done indiscriminately as before the repair. Check the use circumstance of refrigerator. If the refrigerator is installed at the place that is damp or wet, or status of installation is unstable, change the installation place. Do earth in case of need. Particularly, Be sure to earth when there is a risk of an electric leakage by humidity or wetness. Do not use multi plugs in a plug socket at the same time. Check the power cord and socket is damaged, pressed, squeezed, or fired. If the plug or plug socket is damaged, repair or exchange that immediately. Do not store the foods unstable or bottles in the freezing room. Do not repair the refrigerator by user himself. Do not store another materials except the foods. Drugs or scientific materials : difficult to keep a precise temperature. The inflammables(alcohol, benzene, ether, LP gas, butane gas etc.): have a risk of explosion.
CAUTION / WARNING SYMBOLS DISPLAYED SYMBOLS

Warning

Indicates that a danger of death or serious injury exists. means Prohibition. means Do not disassemble. means No contact. means The things to be followed. means Power cord should be unplugged from the consent means Earth to prevent Electric shock.

Caution

Indicates that a risk of personal injury or material damage exists.
Use the rated components on the replacement.
Check the correct model, rated voltage, rated current, operating temperature and so on.
Pull the power plug out to exchange the interior lamp of the refrigerator.
It may cause electric shock.
On repair, make sure that the wires such as harness are bundled tightly.
Bundle tightly wires in order not to be detached by the external force and then not to be wetted.

On repair, remove completely dust or other things of housing parts, harness parts, and check parts.
Cleaning may prevent the possible fire by tracking or short.
After repair, check the assembled state of components.
Check if there is any trace indicating the permeation of water.
If there is that kind of trace, change the related components or do the necessary treatment such as taping using the insulating tape.
It must be in the same assembled state when compared with the state before disassembly.

2. INSTRUCTION

A newly developed SAMSUNG side by side refrigerator has the following characteristics.
1) Multi-Flow System Cool air circulates through multiple vents on each shelf level. This provides even distribution of cooling inside of freezer/refrigerator and keeps food fresher for longer. 2) High humidity for fresher food You can keep food, fruit and vegetables fresh for longer because your refrigerator supplies highly humidified cold air. 3) Door Alarm When the refrigerator door is left open for more than two minutes, a musical alarm is automatically triggered. This feature helps you save electricity and preserve stored foods.

3. INSTALLATION

1) To protect refrigerator in movement Use padded hand truck as shown. If entrance width is less than 30 , remove doors prior to installation and reattach doors according to procedure below. 2) Remove all protective tape and pad in refrigerators. Please adjust the clearance between the doors. 3) Set the temperature control to the temperature and wait for an hour. The refrigerator should get slightly chilled and the motor runs smoothly. 4) Once the refrigerator temperature is sufficiently cool You can store food in the refrigerator. After starting the refrigerator, it takes a few hours to reach the appropriate temperature.
Disassemble the refrigerator 1) 2) 1)
Assemble the refrigerator 2)
1) With the door closed, disassemble screw( ) by using (+) screw driver and then disassemble the upper hinge cover( ). 2) Disassemble bolts ( ) and screws ( ) to the counter-clockwise by using a tool, and take off the upper hinge ( ) along the arrow ( ). Take care when you disassemble the door to ensure that it does not fall on you.
1) Insert the lower hinge ( ) in the bracket lower hinge ( ). 2) Assemble the door ( ) in the lower hinge ( ).
3) Disassemble the door from the lower hinge ( ) by lifting the door ( ). 4) Disassemble the lower hinge ( ) from the bracket lower hinge ( ) by lifting the lower hinge ( ) in the direction of the arrow.
3) Insert the upper hinge shaft ( ) into the hole ( ). After leveling between the upper hinge hole ( ) and the hole of the refrigerator ( ), assemble bolts ( ) and screws ( ) to the clockwise by using a tool. 4) Put the front part of the upper hinge cover ( ) on the front part of the upper hinge ( ) and assemble, starting with the front part of the upper hinge cover. Assemble the screw to the clock wise by using a tool.

4. NOMENCLATURE

Color SW : Snow White SL : Stainless Looking Handle Type C ; Sky Bar Handle E ; Deluxe Bar Handle

Option N : Nothing

Capacity ; Cu. ft
Door Type S - Side By Side Product ; R - Refrigerator

Label Location

5. SPECIFICATIONS
5-1. Model Specification Items Model Name Total Volume Volume capacity Freezer Volume Refrigerator Volume Outer dimensions(width x depth x height) Rated frequency Hz Rated voltage V Rated consumption of Comp. W Rated consumption of Electric heater W Refrigerator type Refrigerant Refrigerant quantity Freezing Capacity Products weight 106kg Specification RS20N*** 496 l(17.5 cu.ft) 188 l(6.6 cu.ft) 308 l(10.9 cu.ft) 850mm724mm1722mm 394 Frost free HFC - 134a 190gr 50/230 125
5-2. Electric Parts Specification
Items Model Name Performance of freezer Type Compressor Freezing parts Operation type Sealing oils Cooler Freezer

Specification RS20N***

110V/60Hz 127V/60Hz 220V/50Hz 220V/50,60Hz 230V/50Hz MK183CL2U/EH1 MK183PL2U/EO1 DK190KT2U/EO1 SK190HL2U/E01 MK183QL2U/EO1 R.S.C.R FREOL - 15 (ESTER) SPLIT FIN TYPE Force and natural convection method MOLECULAR SIEVE XH-9 0.823200, 5.5 kg/cm2 HFC-134a ON() -24.0 -19.0 -15.0 ON() 2.0 4.0 7.hours 10 mins 6~11 hours(Variable according to the use conditions)defrost minutes OFF() -26.0 -21.0 -17.0 OFF() 0.0 2.0 5.0
Condensing method Drying agent Capillary tube Refrigerant Types Freezer temp. Colder Normal Cold Refrigerator temp. Colder Normal Cold
Inner Temperature detection parts

Freezer

Thermistor (F-sensor) 502AT Types
Refrigerator Defrostperiod
Thermistor (R-sensor) 502AT
Period of initial defrost (F defrost) Defrost period of freezer Pause F-defrost sensor Types Spec Rating Operation temp.

Parts related defrost

Defrost sensor
THERMISTOR (PX41C) 5.0 at 25 AC 250V 10A 77

Temperature fuse

Items F-room defrost heater F room heater sub F room heater glass Conducting at F defrosting Conducting at F defrosting Conducting at F defrosting
Specification 200W 60W 130W 3W 1W 250VAC,12 250VAC,12 350VAC,5 350VAC,5 350VAC,5 -
R-room cover damper R room electrically driven damper Condenser for Comp.(monolithic) Start relay Electricparts Running Start Type Action Type Overload relay ON temperature OFF temperature L.V.T(LOW VOLTAGE TRANSFORMER) F room cooling fan motor Comp. Cooling fan motor Freezer interior light Refrigerator interior light Door switch Supply cord Grounding screw
J531Q32E4R7M1802 J531Q32E4R7M1802 J531Q34E220M3502 J531Q34E220M3502 J531Q35E330M3852 Initial resistance: 6820% (Ambient temperature : 25) 4TM437RHBYY-53 4TM437RHBYY-53 4TM317SHBYY-53 4TM317SHBYY-53 4TM265RHBYY-115V/60Hz 127V/60Hz 220V/50Hz 230 240V/50Hz

DC 12V DREP3030LA 0.3A DC 12V DRCP3030LA 0.24A 30W (110 127V) 30W (110 127V) 25W (220 230V) 25W (220 230V)
AC 250V 0.5A 2EA TO BE FOLLOWED LOCAL STANDARD BSBN (Bronze screw)4EA
6. INTERIOR VIEWS AND DIMENSIONS
6-1. The Name of Each Part
Interior light Ice tray Shelf Food Guard Drawer Leg cover

Refrigerator

Dairy compartment Interior light Shelf Egg tray Fresh container(option) Food Guard Vegetable and fruit drawer

6-2. Dimensions of Unit

7. FREEZING CYCLE AND COOL AIR CIRCULATION ROUTE

7-1. Freezing Cycle

Compressor Condenser Evaporator Accumulator
Pipe cluster Pipe suction
Pipe hot Dryer Compressor

Capillary tube

7-2. Cooling Air Circulation
8. MECHANICAL DISASSEMBLY
8-1. Accessories for storage and parts for lightening Door Gasket The door gasket is set into groove on door liner. 1) Open the door. 2) Grasp the gasket and pull it out from the door liner. SHELVES 1) Pull the shelf out as far as it goes. 2) Lift it up and pull it out from the unit.
ICE TRAYS LIGHT SWITCHES The unit have two light switches on the side wall of freezer & refrigerator. 1) Use a small flat-blade screw driver to unlock the hook and pull the switch out until the wire connector is exposed. The ice tray is located at bottom of freezer shelfmid. 1) Pull the tray out by sliding.
DRAWERS LIGHTS The light of freezer & refrigerator are located at upper side of each compartment. 1) Remove the screws. 2) Remove the lamp cover by unlocking the hook. The drawers are located at bottom side of freezer and refrigerator. 1) Pull the drawer out as far as it goes. 2) Lift it up slightly and pull it out from the unit.
SHELF LOW REF. IN REFIGERATOR The shelf low ref. in refrigerator can be removed as following sequence. 1) First, remove the drawer upp. 2) Pull the shelf out as far as it goes. 3) Lift it up and pull it out from the unit.
TRAY-REF The tray-ref is located at bottom of shelf-ref in refrigerator compartment. 1) Pull the tray-ref out as far as it goes. 2) Lift it up slightly and pull it out from the shelf.
FOOD GUARDS 1) Lift the guard up and pull it out from door liner.
8-2. Cooling Unit COVER EVAP FRONT IN FREEZER Before disassemble the cover, Should be removed all accessories in freezer. 1) Pull the screw cap out (4 EA). 2) Remove the screws (6 EA). 3) Grasp the bottom edge of the cover, and pull it out from the unit. COVER DUCT REAR IN FREEZER Before disassemble the cover, Should be removed cover duct. front. 1) Remove the screws (3 EA). 2) Grasp the bottom edge of the cover, and pull it out from the unit. 3) Disconnect the wire connector and pull the cover out from the unt.
COVER DUCT FRONT IN FREEZER Before disassemble the cover, should be cover evap. front. 1) Pull the screw cap out (1 EA). 2) Remove the screws (1 EA). 3) Grasp the bottom edge of the cover, and pull it out from the unit. 4) Disconnect the sensor wire connector and pull the cover out from the unt.

DISPLAY LED R Cold R Cold. Middle R Middle R Middle. Colder R Colder F Cold F Cold. Middle F Middle F Middle. Colder F Colder R room LED No R room LED No R room LED No R room LED No R room LED No F room LED No F room LED No F room LED No F room LED No F room LED No
9-8. C-FAN(Comp-fan) Control In Accordance With Outdoor Temperature 1) According to the ambient temperature, the condenser fan located in the machine compartment is operated with different modes.
Ranges of ambient temp. Above 18 C-FAN Delay function Below 12
Operation C-FAN is ON as soon as the compressor ON. C-FAN is ON with 5 minutes delay from the compressor ON. C-FAN is OFF regardless of the compressor operation.

10. CIRCUIT DESCRIPTION

10-1. Power source part

Power source

Used circuit
Vcc(DC 5V) Surrounding power of MICOM and sensor detection part +2V(DC 12V) Relay driving part, panel display part BLDC(DC 12V) OP AMP, TR constant voltage circuit use(BLDC fan motor drive) AC 220V input power is reduced by passing through LVT(DC-TRANS), this power is changed to DC voltage through rectification diode. After this, DC 12V leveled by 1000uF/35V capacitor and settled by regulator 7812 is output and in use for relay and panel PCB driving power, input power and refrigerator control. Another the second of LVT(DC-trans) is leveled by rectification diode and 1000uF/35V capacitor, and controlled to set voltage by OP amp, constant voltage TR circuit, and then supplies a settled voltage to BLDC motor. 10-2. Oscillation circuit part
Terminal Xin(#30) Xout(#31)
Oscillation frequency 4MHz 4MHz
Oscillation circuit is for clock occurrence for synchronism to the information transmission/reception of MICOM internal elements and for time calculation. If the resonator spec is changed, normal function is not performed because of the changing of MICOM timing system. 10-3. Reset circuit part

Terminal Vcc RESET

Voltage DC 5V DC 5V
Reset circuit is that initializes many internal parts of the MICOM and makes the all programs to act in the initial state in case that power is impressed to MICOM by instantaneous interruption or power input. Reset terminal voltage becomes to scores of us LOW compared to the MICOM Vcc((DC 5V) voltage on power impression, and keeps HIGH (Vcc voltage) on the normal action. 10-4. Door S/W detection circuit

Terminal F room

Door state CLOSE OPEN CLOSE
MICOM input 0V (LOW) 5V (HIGH) 0V (LOW) 5V (HIGH)

R room OPEN

CN30 is connected to GND and is supplied Vcc(DC 5V) by passing through Resistance R401 (10), and it detects F room door open/close by impressing to MICOM HIGH(5V)/LOW. CN30 is connected to GND and is supplied Vcc(DC 5V) by passing through resistance R403(10), and it detects R room door open/close by impressing to MICOM HIGH(5V)/LOW If there are some faults in door S/W at this time, the corresponding fan is not act or alarm occurs. Check the door S/W whether it has an abnormality. If the door is opened, the internal corresponding fan stops. This is occurred because MICOM stops the fan deciding door open although door is closed when being S/W contact point abnormality. 10-5. Temperature detection circuit

MICOM terminal PIN #56 (F-SENSOR)

Voltage

Outdoor temperature PIN #57 (F-DEF-SENSOR) MICOM terminal voltage is PIN #58 (R-SENSOR) changed by the PIN #59 (ATMOSPHERE SENSOR) temperature.
Sensor makes use of the character that resistance value becomes smaller when temperature is high, and bigger temperature is low by use of thermistor having a indeterminate resistance temperature coefficient. R302,4,6,8 and C301,2,3,5 have no concern with temperature detection because they are for noise protection parts. In case of F-sensor, if the voltage that input to MICOM is supposed to Vf, Vf= (Rth x Vcc)/(R301 + Rth).At this, Rth is a thermistor resistance value. Refer to attached appendix for MICOM terminal voltage corresponded to temperature and resistance/voltage conversion table of sensor.
10-6. Key scan and display circuit part
1) Description of key scan and display drive action As a following each part wave, HIGH output is send out, by use of three terminals of MICOM No #5,6,7 by 6 msec intervals. This signal passes through input terminal of IC05 and is displayed to output terminal. At this time, the peak to peak voltage of rectangle wave is about 12V, the shape of output wave is like following.
2) KEY SCAN When GRID #3 wave is output, this signal is supplied to SW1 by passing through panel PCB R5 resistance 10. At this time, pressing SW1 makes a signal small by R508(6.8) and R505(12), and impress peak to peak 4.5V to MICOM. MICOM decides that GRID #3 wave is input and changes the function corresponding to SW1. Like this, each GRID wave is recognized.
10-7. BLDC MOTOR drive circuit
Movement description When F-fan is driven to LOW RPM, Resetting the MICOM #40 pin with being set #39 always links the R705 and R707 in a parallel. At this time, the voltage is devided between a parallel resistance value and R706, impressed to OP-AMP. It makes Q1 turn ON, F-fan drive. If F-fan is in condition of OFF, MICOM #39 pin is reset and F-fan is stopped. In case of the Comp.-fan, it is controlled by the same method with F-fan. But its drive voltage is different with that because there is a difference in E1 voltage /E2 voltage due to the difference of RPM. Fan motor protection When the fan is not run because of F-fan/C-fan freezing or power cord connection part inferiority, fan self-signal is not occurred. So MICOM decides fan abnormality. At this time, perform the fan three seconds ON, seven seconds OFF in five times. If there is no signal during the fan ON/OFF five times, after 10 minutes pausing repeat the three seconds ON, seven seconds OFF in five times. If the signal is occurred during the three seconds ON, seven seconds OFF, MICOM decides that operation is normal and releases all motor protect functions and performs a normal function.

10-10. Options

As like above circuit diagram, it makes change the items related to temperature and function by use of switching diode on the main PCB. Note Because the option is set at shipment, hold free change except a special case. After change be sure to
10-11. Temperature related option Freezer temperature shift (unit: ) SHIFT D601 D602 DStandard 1 -0.-1.-2.-3.+1.+2.+3.1 Freezer hysteresis (unit: ) SHIFT D608 D609 Standard Basic type 3.0 2.5 3.5 4.0
Refrigerator temperature shift (unit: ) SHIFT D604 D605 D606 Standard 0 -0.-1.-2.-3.+1.+2.+3.Refrigerator hysteresis (unit: ) SHIFT D607 Basic type 2.0 Standard 0 1.0 1
Appendix Sensor resistance value in accordance with temperature and MICOM ort voltage Temperature() Resistance() Voltage(V) -42 -41 -40 -39 -38 -37 -36 -35 -34 -33 -32 -31 -30 -29 -28 -27 -26 -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 -14 -13 -4.541 4.518 4.494 4.469 4.443 4.416 4.389 4.36 4.331 4.301 4.269 4.237 4.204 4.17 4.134 4.098 4.061 4.023 3.985 3.945 3.905 3.863 3.822 3.778 3.734 3.689 3.644 3.597 3.551 3.504 3.456 Temperature() Resistance() Voltage(V) -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -6481 6242
Temperature() Resistance() Voltage(V) 1.878 1.834 1.791 1.749 1.707 1.667 1.626 1.587 1.549 1.511 1.474 1.437 1.401 1.366 1.332 1.298 1.266 1.234 1.203 1.172 1.143 1.113 1.085 1.057 1.03 1.003 0.977 0.952 0.928 0.904
3.408 3.36 3.31 3.26 3.209 3.159 3.108 3.057 3.006 2.955 2.904 2.853 2.801 2.75 2.698 2.647 2.596 2.545 2.495 2.445 2.395 2.346 2.296 2.248 2.199 2.151 2.104 2.057 2.012 1.966 1.922
10-12. Electric Circuit Diagram
BLU-BLUE BRN-BROWN E-EARTH GRY-GRAY ORG-ORANGE PNK-PINK PRP-PURPLE RED-RED S/BLU-SKY BLUE WHT-WHITE YEL-YELLOW BLK-BLACK W/BLK-WHITE/BLACK W/RED-WHITE/RED
11. DIAGNOSIS AND TROUBLESHOOTING

11-1. Power cut off

Y Is the power cord or fuse break? N N Is impressed the first power of DC trans? Y Y Is DC 12V, DC 5V on main PCB run? Y N Is normal the power cord on panel PCB?

Fuse exchange

Power cord assembly connection check
REG 7812, 7805 out end measurement
Repair of power part on PCB
Check the connection of housing of main PCB part and refrigerator panel connection part
Y N Is the reset IC (IC02) output terminal DC 5V? Y

Panel PCB exchange

Exchange/repair of reset IC

Exchange of the main PCB ASS Y

11-2. Compressor trouble

Pre-inspection 1. If compressor is off by refrigerator temperature, it is not run within five minutes minimum. 2. Compressor is not run during the defrost. 3. If the freezer sensor is not connected, compressor is not run due to low temperature detection. Start
N Have passed 5 minutes after cut off? Y Y Is compressor run at the forced start?

Check after 5 minutes

Is occurred the forced start alarm?
Is the freezer/refrigerator temperature detection sensor normal? Y
Is impressed DC 12V to the both side end of coil of compressor relay(RY72) on the main PCB?

Exchange inferior sensor

Check power cord connection

Exchange the main PCB

Is impressed between the gloomy line and red line of CN70 AC 220V?
Exchange compressor relay on the PCB
Check the connection of the lines of main PCB part and compressor surrounding OLP, relay PTC
11-3. Defrost failure Condition for decision 1. In case of the defrost inferior, it runs normally at the initial power on. But the freezing and cooling inferior occurs after some times and at the time of defrost. This is a abnormality of defrost system. Refer to the followings. Start
Is the freezer defrost sensor normal by self diagnosis? Y N Is the freezer defrost heater normal? Y Is the temperature of defrost sensor below -5? Y N N
Corresponding sensor change/repair
Check the temperature fuse, heater self break, cord contact
Forced start for a some times
Perform the forced defrost
N Is the defrost heater run? Y After heating some period check heater off.
Is the cord connection terminal of main PCB part normal? Y
Repair the connection terminal
Is the defrost relay normal?
Exchange/repair the defrost relay
11-4. Freezer fan abnormality(BLDC-FAN repair) Condition for decision 1) When the freezer fan is abnormal, freezer and refrigerator weak cooling occurs. This is a freezer fan system failure. Refer to the followings. Start
N Is the compressor off? Y

Forced start

Is it DC 7V~DC 12V between main PCB part GND and CN73 1pin?

F-fan normal

Is it DC 0V between main PCB part CN30 1~2(freezer) and 5~6(refrigerator) pin?
Measure in door closing -. F-DOOR OPEN : DC5V -. F-DOOR CLOSE : 0V
Impress the power after five minutes from the power off(Compressor O/L/protection)
Repair the door S/W connection part
After impression of initial power compressor and fans run continuously. (It runs without regard to temperature)
Is it repeated DC 7V~DC 12V and below 2V between main PCB part GND and CNpin?
If the pulse signal of fan self occurring through CNis not detected to MICOM, fan protection function runs that performs 3 seconds ON 7 seconds OFF in five times. It occurs DC7~12V at the time of 3 seconds ON, it becomes below DC 2V at 7 seconds OFF.

Exchange/repair door S/W

11-7. Circuit service materials list
CODE-NO DA41-00113B DA41-00114A DA26-00009G DA26-00009F DA26-00009A DA26-00009H
Name of goods PBA MAIN ASS Y PBA PANEL ASS Y DC-TRANS DC-TRANS DC-TRANS DC-TRANS R-ROOM SENSOR F-ROOM SENSOR F-EVA SENSOR EXIT SENSOR
Specification RS20N DC12V 110V115V/60Hz 230V240V/50Hz 220V/50Hz 127V/60Hz PX41C(Blue) PX41C(Yellow) PX41C(Yellow) PX41C(White)

Qty 1 1

Remarks
DA32-10105V DA32-10109U DA32-00006B DA32-10109T
12. ILLSTRATED PARTS CATALOGUE

12-1. Parts of Freezer

Parts list of Freezer NO
1 1-1 1-2 1-2-1 2-2 2-3 2-4 2-5 2-3-1 3-2 3-4-1 4-2 4-5-1 5-2 5-6-1 6-2 6-8 8-1 8-2 8-3 8-4 8-9-1 9-2 9-3 9-4 9-5 9-6 9-7
(http://www.e4buyer.com/refrigerator) Name of goods
ASSY-SHELF FRE UP GLASS-SHELF FRE,UP SHELF-FRE UP TRIM-SHELF ASSY-SHELF FRE MID GLASS-SHELF FRE,MID SHELF-FRE MID RAIL-TRAY ICE TRIM-SHELF TRAY ICE SCREW TAPPING ASSY SHELF FRE, LOW GLASS SHELF FRE, LOW SHELF-FRE, LOW TRIM-SHELF ASSY SHELF-FRE SHELF GLASS SHELF-FRE TRIM-SHELF CASE-BASKET ASSY,UP CASE-BASKET UP COVER-FRONT,B COVER-FRONT,A CASE-BASKET ASSY,LOW CASE-BASKET LOW COVER-FRONT,B COVER-FRONT,A CAP SCREW ASSY-COVER DUCT FRONT,FRE COVER-DUCT FRE DUCT FRONT,FRE SENSOR ASSY COVER-SENSOR,A COVER-SENSOR,B ASSY-COVER EVAP FRONT COVER-EVAP FRONT COVER EVAP FRONT PLATE-INS EVAP SEAL-INS EVAP FRONT, LOW PLATE COVER EVAP FRONT SEAL INS EVAP FRONT SEAL INS EVAP FRONT UP

CODE-NO

DA97-00124A DA64-00554A DA67-00644A DA64-00090A DA97-00125A DA64-00554B DA67-00645A DA61-00519A DA64-00090A DA63-01078A 6002-000224 DA67-00181B DA67-00177E DA67-00146A DA64-00090A DA67-00181A DA67-00177C DA67-00146A DA64-00090A DA67-00182A DA67-00150A DA63-00174A DA63-00170A DA67-00183A DA67-00151A DA63-00174A DA63-00170A DA67-30266D DA97-00128B DA63-01085A DA62-00169A DA32-10109U DA63-00798B DA63-00799A DA97-00153A DA63-01061A DA62-00164A DA61-00521A DA62-00259A DA61-00737A DA62-00182A DA62-00260A

RS20N*** CSW ESL

Specification

10 10-1 10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 10-14 15
DA97-00129A DA63-01086A DA63-00713B DA31-00020M DA63-01146A DA39-00227A DA31-00052A DA61-20128A 6002-000480 DA62-00189A DA63-40167A DA63-01075A DA61-00518A 4713-001147 4713-001145 DA34-10120A DA96-00033B DA96-00033A DA97-00155A DA96-00033C DA47-10148M DA32-00006B DA60-00042A DA62-00184A 6002-000215

Name of goods

ASSY-COVER DUCT REAR, FRE COVER-DUCT REAR FRE COVER-MOTOR MOTOR BLDC GROMMET-MOTOR W/HARNESS SUB FAN PROPELLER SPRING ETC-FAN SCREW-TAPPING SEAL-DUCT REAR GROMMET-COVER CHIL COVER LAMP PLATE-REFLELTOR LAMP-INCANDESCENT SWITCH DOOR ASSY-EVAP FRE

DC 12V

110 127V, 25W 220 230V, 30W 110V 230V 220V 127V 250V, 10A, 77

15-1 15-2 15-3 15-4 16

ASSY-THERMO FUSE SENSOR TEMP SPACER EVAP FRE SEAL INS EVAP SCREW-TAPPING
12-2. Parts of Refrigerator
Parts list of Refrigerator NO
1 1-1 1-2-1 2-3-1 3-4-1 4-7-1 7-8-1 8-2 8-9-1 9-2 9-3 9-10-1 10-2 10-3 10-11-1 11-2 11-3 12
(http://www.e4buyer.com/refrigerator) Name of goods CSL RS20N*** CSW ESL ESW Specification
DA97-00126B DA64-00554C DA67-00646A DA97-00126B DA64-00554C DA67-00646A DA61-60183B DA61-60179A DA63-40256B DA61-60184B DA61-60180A DA63-40256B 6002-000215 DA63-01074B DA97-00126B DA64-00554C DA67-00646A DA97-00127B DA64-00554D DA67-00768A DA64-00647A DA97-00118A DA61-00507A DA63-01065A DA63-01064A DA64-00085A DA97-00117A DA61-00508A DA63-01065A DA63-01064A DA64-00085A DA97-00355C DA62-00166A DA31-00043B DA62-00167A DA97-00154C DA97-00154B DA97-00154A DA97-00154D DA63-01073A DA47-00106D DA47-00106B DA47-00106E DA47-00106C
ASSY-SHELF REF, UP GLASS-SHELF REF,UP SHELF-REF UP ASSY-SHELF REFUP GLASS-SHELF REF,UP SHELF-REF UP RAIL-LOW L, ASSY RAIL-LOW L GROMMET-RAIL RAIL-LOW R, ASSY RAIL-LOW R GROMMET-RAIL SCREW-TAPPING TRAY-REF ASSY-SHELF REFUP GLASS-SHELF REF,UP SHELF-REF UP ASSY-SHELF REF, LOW GLASS-SHELF REF,LOW SHELF-REF LOW TRIM-SHELF REF,LOW ASSY-VEG UP CASE-VEG UP COVER-FRONT,B COVER-FRONT,A KNOB-MOIS CONT ASSY-CASE VEG LOW CASE-VEG LOW COVER-FRONT,B COVER-FRONT,A KNOB-MOIS CONT ASSY INS-DAMPER,REF INS-DAMPER UP MOTOR STEP-DAMPER INS-DAMPER LOW ASSY-COVER DAMPER

BASE HANDLE LOW SCREW TAPPING TRIM-HANDLE UPP TRIM-HANDLE LOW SCREW TAPPING TRIM-HANDLE MID, A
DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE
12-5. Parts of the refrigerator door
Parts list of the refrigerator door NO
DA91-01517B DA91-01517G DA91-01517F DA91-01517N DA97-00179A DA97-00732A DA63-01067B DA63-01068A DA63-01069A DA63-10170A 6002-000468 6001-000716 DA61-00776A DA66-90112C 6001-000716 DA64-00110B DA64-00110C DA64-00096B DA64-00096C DA71-00077A 6002-000470 6002-000468 DA64-00097B DA64-00097C DA97-00654B DA97-00654C DA61-00511A 6002-000470 6002-000213 DA64-00209A DA64-00098H DA64-00098B DA64-00196A DA64-00196B DA64-00100L DA64-00100A DA64-00543B DA64-00543C DA64-00379B DA64-00379C DA64-00328B DA64-00328C DA71-00280A 6002-000213 DA64-00329B DA64-00329C

ASSY DOOR FOAM REF

13-1 13-2 13-16-1 16-18 18-1 18-21-1 21-2 21-3 21-4
ASSY-GASKET DOOR, REF ASSY-GUARD,DAIRY COVER-GUARD,DAIRY GUARD-DAIRY GUARD-REF,UP GUARD-REF,LOW SCREW-TAPPING SCREW-MACHINE STOPPER DOOR CAM HINGE-RISER, LOW SCREW-MACHINE ASSY HANDLE MID HANDLE BASE MID REINF HANDLE MID SCREW TAPPING SCREW TAPPING HANDLE BASE UPP ASSY HANDLE LOW REINF HANDLE LOW SCREW TAPPING SCREW TAPPING ASSY TRIM HANDLE MID TRIM HANDLE MID TRIM HANDLE CONNECT MID TRIM HANDLE UPP TRIM HANDLE LOW ASS'Y HANDLE HANDLE REAR REINF HANDLE SCREW TAPPING HANDLE FRONT
SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE
SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE SKI-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE
DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE
DA64-00371B DA64-00371C DA64-00547B DA64-00547C 6002-001122 DA64-00326B DA64-00326C DA64-00544B DA64-00544C 6002-000468 DA64-00324B DA64-00324C
BASE HANDLE UPP BASE HANDLE LOW SCREW TAPPING TRIM-HANDLE UPP TRIM-HANDLE LOW SCREW TAPPING TRIM-HANDLE MID, A
DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE DELUXE-BAR HANDLE
Appendix (RS20N for Circuit Diagram)

ELECTRONICS

272, Oseon-Dong, Kwangsan-Gu, Kwangju-City, Korea, 506-253 TEL : 82-62-950-6810, 6811 FAX : 82-62-950-6829

Samsung Electronics Co., Ltd. Refrigerator Division 2002. 10 Printed in Korea Code : DA68-01197A