When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
To prevent rainwater from running along the outdoor antenna cable and into the house, ensure that the outdoor portion of the cable is hanging below the point of entry. If the product is exposed to rainwater, it may cause electric shock or fire.
When using an outdoor antenna, ensure that there is sufficient distance between the antenna and any electric wires nearby so that they do not come into with each other if the antenna is knocked over by strong wind or any other accident. A knocked-over antenna may cause injury or electric shock. Keep the plastic packaging (bag) out of children's reach. The plastic packaging (bag) may cause suffocation if children play with it.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire.
Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire.

Others

Do not remove the cover (or back). This may cause electric shock or fire. Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center. This may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center. The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. Failure to do so may cause electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor. This may cause a malfunction, electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.
Adjust the resolution and frequency to the level appropriate for the model. An inappropriate resolution may cause undesirable picture quality. 22 inch Wide (55 cm) - 1680 X 1050
Keep the volume at a comfortable level when using the headphones. Excessively loud volume level may damage hearing.
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor. Failure to disconnect cables may damage it and cause fire or electric shock.
Place the product out of children's reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When removing batteries from the remote control, ensure that the children do not swallow the batteries. Keep the batteries out of children's reach. If the batteries are swallowed, see a doctor immediately.
When replacing batteries, place the batteries in the correct +/- polarity position as indicated on the battery holder. The incorrect polarity may cause a battery to break or leak and may cause fire, injury, or contamination (damage). Use only specified standard batteries. Do not use new and used batteries together. This may cause a battery to break or leak and may cause fire, injury, or contamination (damage).
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling purposes as the consumer. The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury.
Good Postures When Using the Monitor Try to maintain a good posture when using the monitor. Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands. Keep the angle of the elbow perpendicular.
Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.

21. SLEEP Turns the monitor off after a pre-determined period of time. 22. PIP - Available in PC/DVI Mode Push the PIP button to turn PIP screen On/Off. 23. AUTO - Available In PC mode Only Adjusts the screen display automatically.

Connecting the monitor

1.Connecting to a Computer
Connect the power cord for your monitor to the POWER on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use appropriate connection for your computer. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the PC port on the back of your monitor. [PC] 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI-D port on the back of your monitor. [DVI-D]
Connect the HDMI / PC / DVI-D AUDIO IN port on the rear side of the monitor to the sound card of the PC. Turn on both your computer and the monitor.
2. Connecting to a Macintosh
1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the D-SUB port on the Macintosh computer. [D-SUB] 2. Turn on the monitor and Macintosh.
Connecting to Other devices
This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product.
1-1. Connecting AV Devices
The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on.
1. Input devices such as DVD, VCR or Camcorder are connected to the VIDEO or S-VIDEO terminal of the monitor using the Video or S-Video cable. 2. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the R-AUDIO-L port of the monitor. 3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 4. Select AV or S-Video using the SOURCE.
1-2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART.
Connect to the DVD Devices input if the device has a EXT (RGB) jack. You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on.
1. Connect the EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 2. Select Ext. by using the SOURCE.

2. Connecting TV

You may view television programs on the monitor if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your computer.

1. Folding the base

The monitor may be reclined from -1 to 23 degrees.

2. Attaching a base

This monitor accepts a 100 mm X 100 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Turn the fixing screw handle on the stand counterclockwise to loosen it and then separate it from the stand. 4. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface. Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Please use Wall Mount according to the International standards.
Installing the monitor driver (Automatic)
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (WorldWide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
1. Insert CD into the CD-ROM drive. 2. Click "Windows" 3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. (Microsoft Windows XP Operating System)
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung.com/ 5. Monitor driver installation is completed.
Installing the monitor driver (Manual)
Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below.

Internet web site :

http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

10. Monitor driver installation is completed. Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install

1. 2. 3. 4.

5. 6. 7. 8. 9. 10.
Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced.". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.
Microsoft Windows Millennium Operating System Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location." then click "Next" button. Click the "Have Disk" button Specify A:\(D:\driver) then click "OK" button. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

SOURCE

Position

Picture

PC / DVI Mode
The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD MagicBright Description MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Text, Internet, Entertain and Custom. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing the MagicBright control button. - The direct button on the remote control is 'M/B' button. 1) Entertain : High Brightness For watching motion pictures such as a DVD or VCD. 2) Internet : Medium Brightness For working with a mixture of images such as the text with graphics added. 3) Text : Normal Brightness For documentations or works involving heavy text. 4) Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu. Custom You can use the on-screen menus to change the contrast and brightness according to personal preference. 1) Contrast : Adjusts the Contrast. 2) Brightness : Adjusts the Brightness. If you adjust the picture by using Custom function, MagicBright will turn to the Custom mode. Colour Tone The tone of the colour can be changed. The individual colour DTVs are also user adjustable. 1) PC : Cool / Normal / Warm / Custom 2) DVI : Cool / Normal / Warm Adjusts the individual R, G, B Colour Controls. 1) Red 2) Green 3) Blue - Available in PC Mode Only If you adjust picture by using Colour Control function, Colour Tone will turn to the Custom mode. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitter and shimmer. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. - Available in PC Mode Only 1) Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. 2) Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). 3) Sharpness - When the SOURCE is set to DVI, only this function operates. : Adjusts the picture sharpness. 4) Position : Adjusts the screen location horizontally and vertically. Play / Stop

Colour Control

1) Coarse 2) Fine 3) Sharpness

4) Position

Auto Adjustment
The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, auto function is performed. - The direct button on the remote control is the 'AUTO' button. - Available in PC Mode Only You can switch the Size. 1) Wide 2) 4:3 You can adjust the PIP Screen Settings. - Available in PC / DVI Mode Only 1) Contrast : Adjusts the Contrast of the PIP window on the screen. 2) Brightness : Adjusts the Brightness of the PIP window on the screen. 3) Sharpness : Adjusts the Sharpness of the PIP window on the screen. 4) Colour : Adjusts the Colour of the PIP window on the screen 5) Tint : Adds a natural tone to the PIP window. The Tint is connected by switching to NTSC from PAL broadcasting and is displayed on the menu while watching. But it is not displayed when watching a general PAL broadcast. For more information, see Broadcasting system by Country. Available : PIP ON

Custom

Auto Volume Sound Select

Channel

The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Country Description Select the country in which the product is being used before you use the Auto Store feature. If you do not see your country in the list, select Others. 1) Belgium 7) Sweden 2) France 8) Switzerland 3) Germany 9) United Kingdom 4) Italy 10) Others 5) Netherlands 11) CIS 6) Spain 12) E. Europe You can scan the frequency ranges available on your television in your area and store all the channels found automatically. You can scan the frequency ranges available on your television in your area and store all the channels found manually. 1) Programme : Inputting the appropriate program number on the screen. 2) Colour System: Adjusts repeatedly until the colour is of the best quality. (Auto <-> PAL <-> SECAM <-> NTSC4.43 ) 3) Sound System: Adjusts repeatedly until the sound is of the best quality. (BG <-> DK <-> I <-> L) 4) Channel : Choosing the air channel through the adjustment of up/down under the current frequency. 5) Search: The tuner scans the frequency range until the first channel or the channel that you selected is received on your screen. 6) Store : It's used to restore the number user inputs. 1) Channel Manager : You can add or delete a channel so only channels you want are displayed. 2) Child Lock : Protects children from viewing inappropriate programs by blocking certain broadcast or video programs. The Child Lock feature can be selected only from the remote. Play / Stop

Auto Store Manual Store

Channel Manager
It's used to exchange the numbers of two channels.
If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required.
Fine Tune Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly.
The default setting may be different depending on the selected Input Mode (input signal SOURCE selected in External Input List) and the selected resolution. OSD Language Description You can choose one of 8 languages. Play / Stop

2. Not Optimum Mode If the vertical resolution is not optimum mode, you can still see the display but the warning message below appears and disappears after one minute. The user must adjust the frequency within that one minute.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are
supported by the monitor.
3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start Settings Control Panel Display Settings Advanced Adapter. If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly installed. Install the adapter driver again according to the information provided by the computer or video card manufacturers. 2. Installing Adapter Driver The instructions given below are for general circumstances. For specific issues, contact the relevant computer or video card manufacturers. 1) Click Start Settings Control Panel Display Settings Advanced Adapter Update Driver Next Display a list of the known drivers for this device so that I can choose a specific driver Next Have Disk (Insert Video Card Driver diskette) OK Next Next Finish. 2) In case you have Adapter Driver Setup file on your computer: Run Setup.exe or Install.exe, which is found in the Adapter Driver Setup file.
4. Maintenance and Cleaning 1. Maintaining the Monitor Case. Clean with a soft cloth after disconnecting the power cord. Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend a Samsung cleansing agent is used to prevent damage to the screen. 2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) The user will be required to pay costs and related expenses for repair of damages caused by him/her.
5. Symptoms and Recommended Actions A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the SOURCE of the problem, and then contact a service center or your dealer. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if you installed the adapter(video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 56 Hz ~ 75 Hz. (Do not exceed 60 Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.

"Check Signal Cable" message
"Not Optimum Mode" message
Picture rolls vertically.
Image is not clear. Picture is blurred.
Picture image is unstable and vibrates. Ghost images are shown in the picture. The image is too light or too dark
Adjust the Brightness and Contrast. (Refer to the Brightness, Contrast) Adjust color using Custom under OSD Color Adjustment menu.
Screen color is inconsistent. Color image is distorted with dark shadows. White color is poor.
Power Indicator blinks green.
The monitor is currently saving the changes made in settings to the OSD memory. The monitor is using its power management system. press a key on the keyboard
Screen is blank and power indicator light is steady green or blinks every 0.5 or 1 seconds The screen is blank and is blinking.
If you see the "TEST GOOD" message on the screen when you press the MENU button, check the cable connection between the monitor and the computer to ensure that the connector is properly connected.
3. Problems related to Audio Problems related to audio signals and their solutions are listed below. Problems No sound Solutions Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card. (Refer to the Connecting the Monitor) Check the volume level. (Refer to the Volume) Check the volume level. (Refer to the Volume) If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjust the Treble and Bass to appropriate level.
The sound level is too low.
Sound is too high pitched or too low pitched
4. Problems related to Remote Control Problems related to the remote control and their solutions are listed. Problems The remote control buttons do not respond. Items to check Check the battery polarities (+/-). Check if the batteries have been exhausted. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity.

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Blue Less than 58 W Power saving mode Blue, Blinking Less than 1 W Power off Black Less than 2 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency Vertical Frequency

Pixel Clock

Sync Polarity
(kHz) IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC,1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA 1280 x 960 VESA, 1280 x 1024 VESA, 1280 x 1024 VESA, 1680 x 1050 31.469 31.469 31.469 35.000 49.726 68.681 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 65.290
(Hz) 70.086 59.940 70.087 66.667 74.551 75.062 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.954
(MHz) 25.175 25.175 28.322 30.240 57.284 100.000 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.00 108.00 108.00 135.00 146.250
(H/V) +/-/-/+ -/-/-/-/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ +/+ -/+
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx
Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 0-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

organization that has been organized to promote its development and management. EIAJ Electronic Industries Association of Japan.

For Better Display

1. Adjust the computer resolution and screen inection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. Resolution: 1680 x 1050 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT LCD sub pixels contained in this product are 5,292,000. 3. When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly. If excessive force is applied, you may stain it. 4. If you are not satisfied with the quality of picture, you can get better quality of picture by executing "auto adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the automatic adjustment, use the FINE/COARSE adjustment function. 5. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time. 6. Do not display a still image( such as on a video game or when hooking up a DVD to this LCD_TV ) on the Color TFT-LCD ( Thin Film Transister Liquid Crystal Display) panel for a long time as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image.

Authority

Information in this document is subject to change without notice. 2007 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
MXICO IMPORTADO POR: SAMSUNG ELECTRONICS MXICO. S.A. de C.V. Va Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitln, Estado de Mxico, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 Samsung Electronics CO.,LTD. 416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea

EXPORTADO POR:

PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 20 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle. Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.

PRICELIST 2007

PROJECTORS

VIPRPTD5600

VIPRPTD5700
PANASONIC PTD5600E PANASONIC PTD5700E
DLP 5000 ANSI LUMEN DLP 6000 ANSI LUMEN

XGA XGA

500,00 500,00
VIPRLE50.8 VIPRLE51.3-1.8 VIPRLE51.8-2.5 VIPRLE52.5-4.0 VIPRLE53.4-4.5 VIPRLE54.5-8.4
PANASONIC LENS FOR PTD 3500/5600 SERIES PANASONIC LENS FOR PTD 3500/5600 SERIES PANASONIC LENS FOR PTD 3500/5600 SERIES PANASONIC LENS FOR PTD 3500/5600 SERIES PANASONIC LENS FOR PTD 3500/5600 SERIES PANASONIC LENS FOR PTD 3500/5600 SERIES
WIDE ANGLE SHORT THROW ZOOM STANDARD ZOOM LENS MEDIUM THROW LENS LONG THROW ZOOM LENS VERY LONG THROW ZOOM LENS
0,8:1 1.3 ->1.8 1.8 -> 2.5 2.5 -> 4.0 3.4 -> 4.5 4.5 -> 8.4
100,00 75,00 75,00 75,00 75,00 100,00

VIPRPTD10000

PANASONIC PTD10000E
DLP 10000 ANSI LUMEN with SDI board

1.750,00

VIPRLEP0.8 VIPRLEP1.5-2.0 VIPRLEP2.0-3 VIPRLEP3.0-5.0 VIPRLEP5.0-8.0
PANASONIC LENS FOR PTD7000/7500/7600/7700/10000 PANASONIC LENS FOR PTD7000/7500/7600/7700/10000 PANASONIC LENS FOR PTD7000/7500/7600/7700/10000 PANASONIC LENS FOR PTD7000/7500/7600/7700/10000 PANASONIC LENS FOR PTD7000/7500/7600/7700/10000
WIDE ANGLE SHORT THROW ZOOM STANDARD ZOOM LENS MEDIUM THROW LENS LONG THROW ZOOM LENS
0,8:1 1.5 -> 2.0 2.0 -> 3.0 3.0 -> 5.0 5.0 -> 8.0
250,00 150,00 150,00 150,00 200,00
All NEW products or price changes are marked in RED
LCD SCREENS & PLASMA* DISPLAYS
* Please read our burn-in precautions and our burn-in conditions

VIMOE19

NEOVO E-19 LCD DISPLAY
1280 X 1024 Incorporated speakers DVI VGA

VIMOVESA10 VIMOX19

VESA WALL MOUNT 10 FOR LCD

NEOVO X19AV LCD DISPLAY

Max. 5 kg 1280 x 1024

Data & Video

Composite YUV Data up to UXGA

5,00 75,00

VIMOLCD22 VIMOLCD27
SAMSUNG SYNCMASTER 225MW SAMSUNG SYNCMASTER 275T
1650 x x 1080 Incl. Wall Bracket

70,00 100,00

Composite YUV Data up to UXGA HDCP compliant DVI input

VIMO32

SAMSUNG SYNCMASTER 320PX
1366 X 768 Incl. Wall Bracket Remote Truss Mount

125,00

VIMO42
PANASONIC TH-42PH9 plasma 42
1024 x 768 Incl. Wall Bracket Remote Truss Mount

175,00

VIMO42SP
PAIR OF SPEAKERS FOR PANASONIC 42

VIMO50

PANASONIC TH-50PH9EK Plasma 50
1366 x 768 Incl. Wall Bracket Remote Truss Mount Inputs: Composite YUV VGA (HD15)

225,00

VIMO50SP
PAIR OF SPEAKERS FOR PANASONIC 50
25,x 1080 Incl. Wall Bracket Remote Truss Mount Inputs: Composite YUV VGA (5 x BNC) DVI FULL HD 600,00

VIMO65HD

PANASONIC TH-65PF9 Plasma 65

VIMO65SP

PAIR OF SPEAKERS FOR PANASONIC 65
40,x 1080 FULL HD Incl. Wall Bracket Rigging Rings on Top (3) Inputs: Composite YUV VGA (5 x BNC) - DVI 2.500,00

VIMO103HD

PANASONIC TH-103PF9 Plasma 103 *

VIMOSTAND

TRAVELS ONLY WITH MINIMUM ONE AED REPRESENTATIVE Center screen Center screen Center screen 1m75 1m50 1m00 30,00 45,00 45,00

PLASMA DESIGN STAND

LED SCREENS

VILDLVD638

HIBINO CHROMALED 638B32*
6mm High Resolution Black Face LEDs 16-Bit Processing High Definition 768 x 576 x 165mm 128 x 96 pixels per module

500,00

FULL price per m2 1.100,00

VILDDLC612

CHROMALED PROCESSOR DLC612
High Definition Processor 02 x Video Board with Composite YUV / HD-SDI 02 x Data /DVI Input Output up to 4096 x 2196

900,00

VILDMI150

BARCO MISTRIP 613*

Creative LED strip 13mm pixel pitch 6000 NIT point brightness IP65 Indoor & Outdoor Order Controller separately Order Processor separately Order cabling separately LED Wall Processor Compatible with all Barco LEDs Order inputs separately SDI Input XGA Input (on HD15) HD-SDI Input

BARCO D320Lite

VILDD320LITE VILDD320SDI VILDD320VGA

550,00

35,00 35,00 65,00

VILDCOMPACT

BARCO COMPACTLINK 50
DVI Extender up to 50m IP65 To extend D320 signal between D320 and device or between devices

100,00

VILDFIBER300

BARCO FIBERLINK 1

Fiber transmitter & receiver Fiber length: 300m

250,00

VILDLC2140

MARTIN LC 2140

Transparent Led Panel 2m x 1m 40mm Pixel Pitch 1800 NIT Only 10kg / m2 Processor & cabling included DVI input Genlock input Only per 4 panels 200m2 available!

220,00/unit

110,00/m2

CHROMA-Q COLORWEB 125

Tranparent LED Curtain/Backdrop 125mm pitch 80 NIT 2kg/m2 IP65 RGB SMD node Easy assembling Control through Artnet 300m2 available!

75,00/m2

* always with technical assistance from AED Display

PROJECTION SCREENS

VISC240X180 VISC300X225 VISC400X300
PROJECTION SCREEN 240 x 180 4/3 PROJECTION SCREEN 300 x 225 4/3 PROJECTION SCREEN 420 x 325 4/3
FASTFOLD FRONT & RETRO KIT FASTFOLD FRONT & RETRO KIT FASTFOLD FRONT & RETRO KIT

65,00 80,00 100,00

VISC640X480 VISC800X600
PROJECTION SCREEN 640 x 480 4/3 PROJECTION SCREEN 800 x 600 4/3
HEAVY DUTY LADDER FRONT & RETRO KIT HEAVY DUTY LADDER FRONT & RETRO KIT

200,00 300,00

VISC500X300
PROJECTION SCREEN 500 x 300 16/9
HEAVY DUTY LADDER FRONT & RETRO KIT

150,00

VIDEO MIXERS

VIMXMX70

PANASONIC MX70
DIGITAL EFFECT MIXER 4 YUV INPUTS OR 8 COMPOSITE INPUTS DIGITAL FRAMESTORE LUMINANCE & CHROMA KEY GENLOCKABLE 6 INPUTS AUDIO MIXER SAME SPECS BUT WITH SDI INPUTS & OUTPUTS

VIMXMX70SDI

PANASONIC MX70 SDI

200,00

PREVIEW MONITORS

VIMOPVM15

JVC TM-15 MONITOR 15
COMPOSITE / S-VIDEO inputs and outputs 16/9 4/3 switchable Underscan / Overscan function

JVC TM-15 SDI MONITOR 15

VIMOPVMSDI
Same Specifications but with SDI in/out

VIDEO SOURCES

VIPLDVDPANA

PANASONIC DVD PLAYER

DVD/S-VCD/VCD/MP3/DIVX PLAYER PROGRESSIVE YUV OUT

VIPLBLURAY

PANASONIC BLU-RAY DVD PLAYER
BluRay DVD Player Plays all CD/VCD/DVD Formats Outputs: Composite/S-Video/ YUV/HDMI Progressive Out up to 1080i On-board 7.1 Dolby Processing DVD Recorder Records different formats 160GB Disk space Outputs: Composite/S-Video/ YUV/HDMI Progressive Out up to 1080i Professionel Harddisk Player/Recorder Inputs: Video/S-video/YUV/SDI/Timecode Outputs: Video/S-video/YUV/SDI/Timecode 36 GB 15000 RPM Harddisk

VIPLDVDREC

SONY DVD HDD RECORDER

VIPLV1D

DOREMI V1D MP2 PLAYER/RECORDER

VIPLPANDORA

PANDORAS BOX MEDIAPLAYER PRO

VIPLPRONTOHD

DVS PRONTO HD SERVER
Professional Media Server Ver. 3.Video Layers + 8 Graphic Layers Live Video Input: Composite/SDI/YUV DMX Interface to communicate with all Types of DMX Controllers 300 Medialoops installed 2 LCD screens included HIGH DEFINITION PLAYER/RECORDER 1100GB Disk Storage (180 min HD) Uncompressed SD and HD Recording Timeline control software LTC in & out Analogue RGB/YUV output Digital DVI output Digital BNC output (SD&HD) Audio: 8 x AES/EBU and 16 ch embedded RS422 remote control + VTR emulation

1.200,00

SIGNAL PROCESSING

VISPDA6

EXTRON DA8/4
VIDEO DISTRIBUTION AMPLIFIER WITH EQ 1 Input -> 8 outputs 2 Inputs -> 4 Outputs SDI DISTRIBUTION AMPLFIER WITH EQ 1 Input -> 4 outputs UXGA DISTRIBUTION AMPLIFIER 1 Input -> 4 outputs (on HD15)

VISPDA6SDI

EXTRON DA4 SDI EXTRON DA4 UXGA

50,00 40,00

VISPDA4

VISPDARGBHV

EXTRON RGBHV DA6 SPLITTER EXTRON MATRIX VIDEO 8 x 8
Wideband RGBHV Splitter 1 to 6 VIDEO MATRIX SWITCHER 8 Inputs -> 8 outputs router

80,00 160,00

VISP8X8

VISP8X8RGB

EXTRON MATRIX RGBHV 8 x 8
RGBHV MATRIX SWITCHER 8 Inputs -> 8 Outputs Router Ethernet Controller

VISP8X8SDI

EXTRON MATRIX SDI 8 x 8
SDI VIDEO MATRIX 8 x Inputs -> 8 Outputs Router RS232 Controller

VISPSW4

EXTRON DATA SWITCHER SW4
DATA SWITCHER 4 Inputs -> 1 Output on HD15

VISPUSP405

EXTRON USP405 SCANCONVERTER
Universal Scanconverter & Multi-Format Switcher Input 1 : RGB on HD15 Input 2 : Configurable Input on 5 x BNC Input 3 : Composite Video on BNC (PAL/NTSC) Input 4 : S-video on Mini Din 4P (PAL/NTSC) Input 5 : SDI video on BNC Input 6 : Genlock All inputs (except. Input 2) have a loop-through. All inputs have independent Size & Positioning Output : Configurable to Video (PAL/NTSC), Svideo, YUV, RGB, SDI, VGA, SVGA, XGA, SXGA, SXGA+, UXGA

190,00

VISPISS506
EXTRON ISS506 SEAMLESS SWITCH
Universal Scanconverter & Multi Format Switcher Input 1 -> 4 : Configurable Video -> UXGA Input 5: SDI/HD-SDI Picture in Picture function Seamless switching and wiping All inputs can be scaled Program Output: Configurable as RGB/YUV on HD15 or 5 x BNC SDI - HD SDI High Definition Scanconverter DVI and XGA inputs Universal Input (configurable) Video and s-video input SDI/HD-SDI input on BNC Genlockable HD-SDI on BNC and DVI Connections Aspect Ratio Converter

VISPFOLSOMHD

FOLSOM IMAGEPRO HD
CABLES & ACCESSORIES*

CAVIBNC.

BNC VIDEO CABLE COAX
Neutrik connectors 03m 05m 10m 15m 20m 30m 100m on Roll 0,50 0,60 0,70 0,75 0,80 1,00 15,00

CAVIRGB.

MULTICABLE BNC 7 x BNC
05m 10m 15m 20m 50m on Roll 100m on Roll 03m 05m 10m 15m 20m 30m Breakout to 5 x BNC HD15 FEM -> FEM VGA EXTENDER HD15 MALE -> MALE VGA ADAPTER BNC FEM->FEM ADAPTER BNC FEM -> CINCH MALE ADAPTER BNC MALE -> CINCH FEMALE ADAPTER SCART BREAK-OUT TO VIDEO & AUDIO (RCA) S-VIDEO (Mini-Din 4P) to 2 x BNC Adapter 20 x HD15 FEM->FEM VGA EXTENDER 40 x BNC FEM->FEM ADAPTER 10 x BNC FEM->CINCH FEM ADAPTER
2,50 3,50 4,50 5,50 35,00 50,00 0,50 0,75 1,00 1,25 1,50 2,50 1,50 0,20 0,20 0,10 0,10 0,10 1,00 1,00 12,00

CAVIVGA.

VGA CABLE SUB D15

CAVIAD.

ADAPTERS BNC / VGA

CAVIADKIT

VIDEO ADAPTER KIT

FLCABNCKIT1

BNC CABLE KIT 1
10 x BNC 03m 10 x BNC 05m 10 x BNC 10m 05 x Multi 10m 10 x BNC 15m 10 x BNC 20m 10 x BNC 30m 05 x Multi 15m 10 x VGA 05m 10 x VGA 10m 10 x VGA 15m 10 x VGA 20m 10 x VGA to 5 x BNC For Video signals For SDI signals For HD-SDI signals For Data signals

FLCABNCKIT2

BNC CABLE KIT 2

FLCAVGAKT

VGA HD15 KIT
VISPGLI VISPGLISDI VISPGLIHDSDI VISPGLIRGB

GROUND LOOP ELIMINATOR

15,00 30,00 40,00 50,00
TECHNICAL & LOGISTICS SUPPORT
TTTEVIDEO TTEVIDEO16 TTEXCATER TTEXHOTEL TTTRCAR TTTR20 TTTR50 TTTR100 TTTEDRIVER
VIDEO TECHNCIAN 1 DAY MAX. 10h VIDEO TECHNICIAN 1 DAY MAX. 16h CATERING FEE PER TECHNICIAN PER DAY HOTEL NIGHT PER TECHNICIAN PER DAY PERSONNAL TRANSPORT CAR MERCEDES SPRINTER 16m3 MERCEDES ACTROS 50m3 MERCEDES TRAILER 100m3 PER KM WITHOUT DRIVER PER KM WITHOUT DRIVER MIN. 75,00 PER KM WITHOUT DRIVER MIN. 150,00 PER KM WITHOUT DRIVER MIN. 320,00
325,00 425,00 50,00 150,00 0,50 0,65 1,00 1,50
DRIVER PER HOUR 27,50 ALL TRANSPORTS ARE CALCULATED FROM AED DISPLAY WILLEBROEK TO THE DESTINATION AND BACK ALL AED TRANSPORTS MUST BE ACCOMPANIED BY AN AED DRIVER

TTWAPP TTWABURN TTWALOAD

PRE-PRODUCTION WAREHOUSE BURN-IN PLASMA SCREENS SPECIAL LOADING OF VANS/TRUCKS/TRAILERS

PER HOUR PER UNIT + EXTRA RENTAL DAY SCREEN

30,00 150,00 100,00

STAFFELS
1 DAY 2 DAYS 3 DAYS 4 DAYS 5 DAYS 6 DAYS 7 DAYS 8 DAYS 9 DAYS 10 DAYS 11 DAYS 12 DAYS 13 DAYS 14 DAYS 15 - 21 DAYS DAYS DAYS LONGER PERIODS
Max. 4 Transport days free of charge.
x 1,00 x 1,50 x 2,00 x 2,25 x 2,50 x 2,70 x 2,85 x 3,00 x 3,00 x 3,00 x 3,00 x 3,00 x 3,00 x 3,00 x 3,50 x 4,00 x 5,00 contact us
BURN-IN EFFECTS OF PLASMA SCREENS
Plasma screens have the specification to easily burn-in pictures which are displayed for longer than 10 minutes. This mean that a still picture (eg. logo) is still visible in other pictures after removing that picture. How to avoid this burn-in effects? Never put the same still picture for longer than 10 minutes on the screen. This will lead in any case to burn-in effects. You should inform your client when preparing his presentation or movie. If there is a moving picture (eg. moving logo) always running on the screen, put the contrast and brightness down to the minimum.
What in case of burn-in effects? If you are aware of a screen with burn-in effects, you should inform the rental department of this. Each returned screen will be checked on burn-in effects; if a screen is detected with burn-in effects a standard fee of 150,00 /screen will be charged. AED Display will run a special program on the screen during max. 3 days; if after 3 days the effects are still visible the full amount of a new plasma screen will be charged.
NEW EQUIPMENT AUDIO / LIGHT / RIGGING
AMPLIFIER RACK 4 x QSC PLx 4000W PIONEER DJM-800 MXING DESK PIONEER CDJ-1000 MKIII CD/MP3 PLAYER GRAND MA FULL SIZE FLYING PIG ROADHOG FLYING PIG iPC FLYING PIC EXTENSION WING AVOLITES ART x 2Kw DIMMER VERLINDE SM20 2000KG HOIST ZAP MINIBIG 3.0 ZAP SUPERBIG 6.0 ROBERT JULIAT 934 SNX 2500 HMI
HOW TO ORDER AT AED DISPLAY
Please send all requests, confirmations , changes and cancellations to
Belgium, United Kingdom, Spain, Italy: The Netherlands: Germany, Austria, Schweiz, Poland: France:
* Sending your request: * Ordering equipment: * Cancelling or changing equipment
display@aedrent.be display@aedrent.nl display@aedrent.de display@aedrent.fr
only by fax or e-mail only by fax or e-mail only by fax or e-mail
Requests, orders, changes or cancellations at the phone will not be processed.
Please mention following items at your requests and orders: Effective Period of Use Handling Period (Shipment dates) Transport and Installation days are free, max. 4 days including pick-up day and return day. These dates must be respected. We are not responsible for sudden changes in these dates caused by the customer. If this results in a partial or total cancellation, the cancellation rules will be applied. Late returns will be charged as a new rental period. How to determinate these dates of pick-up and returning equipment?

Delivery start at 2.00PM Material must be returned before 11.30AM. If you are late, you will make the next customer wait for his order and cause him or her to be unsatisfied.
All related costs (transport, handling, shipping, extra rental,.) caused by the late return will be invoiced to the customer. The requested Equipment and the correct quantity Take care that all accessories must be ordered separately We are not responsible for not ordered equipment If you are not sure for some items or connections, please contact the Rental Department for some advice. Ordering equipment can go in 3 stages: * The Offer: this document indcates prices and doesnt guarantee availability Accepting the conditions of the Offer and signing this order for confirmaton and fax it to the Rental Department. Receipt of this fax will be confirmed as an order when the requested equipment is available for the requested period. this document reserves the requested equipment for the requested dates.

* The Option:

The option is only reserving equipment for a few days and expires automatically after a few days. If you sign the Option before its expiry date, it becomes an order. * The Order: this document immediately reserves the equipment for the requested period. After receipt of one of above documents, the customer must check if the requested equipment, requested quantities and requested handling and effective period are correct. Cancellations: Always by fax or e-mail You must clearly indicate CANCELLATION on the Order Form For general equipment, you will be charged 50% of the total price if you cancel within seven days before equipment leaves AED Displays warehouse. All additional handling, transport, shipping and related costs will be invoiced to the customer. All costs related to the cancelled rental done before the cancellation will be invoiced. For LED screen, no cancellations are accepted at all. The total price will be invoiced to the client.
Payment at delivery: If your Order voucher indicates PAYMENT ON DELIVERY you will have to pay the total amount of the rental before picking up the goods and all other outstanding invoices of more than 2 months. You can pay cash or submit a proof of payment issued by your bank. Cheques are not accepted. Penalties when returning equipment in bad condition: Cleaning & Conditioning equipment: Repairs: Burn-out plasma screens:*

* burn-out plasma:

25,00 / h 35,00 / h + parts 150,00 / unit
if it is not possible to clear burn-in effects the total cost for replacing the plasma panel will be invoiced, added with the rental cost for the repair period in which AED is not able to rent out the plasma.
Monday -> Friday: Saturday:
09h00 -> 18h00 09h00 -> 13h00