Avoid installing the product in a badly-ventilated location such as inside a bookshelf or closet. Otherwise, it may result in fire due to internal over-heating.
Keep a distance of at least 10 cm from the wall when installing the product for ventilation. Otherwise, it may result in fire due to internal over-heating.
Keep the plastic bags used to pack the product away from children. If children place the plastic bags over their heads, they may suffocate.
Avoid installing the product in a location that is unstable or exposed to excessive vibrations such as on an unstable or slanted shelf. The product may fall and this may result in damage to the product or injury. If you use the product in a location exposed to excessive vibrations, it may result in a problem with the product or fire.
Avoid installing the product in a location exposed to dust, moisture (sauna), oil, smoke or water (rain drops) and installing it within a vehicle. This may result in electric shock or fire.
Avoid installing the product in a location exposed to direct sunlight and installing the product near a heat source such as a fire or heater. This may shorten the product life cycle or cause fire.
Avoid installing the product at an easily reachable height where children may reach it. If a child touches the product, the product may fall and this may result in injury. Since the front part is heavier, install the product on a flat and stable surface.
Do not let the product drop while moving it. This may result in a problem with the product or injury. Do not place the product face down on the floor. This may damage the panel of the product.
When installing the product on a console or shelf, make sure that the front of the product does not protrude out of the console or shelf. Otherwise, this may cause the product to fall off and result in a malfunction or injury. Make sure to use a cabinet or shelf suitable to the size of the product.
When putting the product down, handle it gently. Otherwise, it may result in a problem with the product or injury.
If the product is installed in a location where the operating conditions vary considerably, a serious quality problem may occur due to the surrounding environment. In this case, install the product only after consulting one of our service engineers about the matter. Places exposed to microscopic dust, chemicals, too high or low temperature, high humidity, such as airports or stations where the product is continuously used for a long time and so on.

Cleaning Related

Since using a surfactant, which contains a large amount of alcohol, solvent or other strong chemicals, may result in the discoloration or cracking of the product exterior or the panel surface coming off, be sure to use the recommended cleansing agent only. You can purchase the recommended cleansing agent from a service center. Before cleaning the product, unplug the power cord. Otherwise, it may result in electric shock or fire. When cleaning the product, do not spray water directly over the product parts. Make sure that water does not enter the product. Otherwise, it may result in fire, electric shock or a problem with the product.
Avoid spraying cleansing agent directly onto the product. This may result in discoloration or cracking of the exterior of the product or the panel coming off. When cleaning the product, disconnect the power cord and clean the product with a soft dry cloth. Avoid using chemicals such as wax, benzene, alcohol, thinner, mosquitorepellent, fragrance, lubrication or cleansing agent when cleaning the product. This may result in the exterior being deformed or the print being removed. Use a soft, damp cloth with a "monitorexclusive cleansing agent" and wipe the product with it. If no monitor-exclusive cleansing agent is available, dilute a cleansing agent with water at a ratio of 1:10 before cleaning the product. Since the exterior of the product is easily scratched, be sure to use a proper cleansing cloth. Use the cleansing cloth with a small amount of water. However, if the cloth is contaminated by alien substances, it may result in scratches to the exterior; therefore shake off any alien substances from the cloth before using it.

Usage Related

Since a high voltage runs through the product, never disassemble, repair or modify the product yourself. Otherwise, it may result in fire or electric shock. If the product needs to be fixed, contact a service center. When cleaning the product, do not spray water directly over the product parts. Make sure that water does not enter the product. Otherwise, it may result in fire, electric shock or a problem with the product.
If the product generates a strange noise, a burning smell, or smoke, unplug the power plug immediately and contact a service center. Otherwise, it may result in electric shock or fire.
Avoid letting children to hang or climb onto the product. Otherwise, it may result in the product falling and this may result in injury or death.
If you drop the product or the case is damaged, turn the power off and unplug the power cord. Contact a service center. Otherwise, it may result in fire or electric shock.
Avoid placing objects such as toys and cookies on top of the product. If a child hangs over the product to grab an object, the object or the product may fall and this may result in injury or even death.
When thunder or lighting occurs, unplug the power cord and under no circumstance touch the antenna cable as this is dangerous. Otherwise, it may result in electric shock or fire.

Watching the product from too close a distance continuously may damage your eyesight.
Avoid using a humidifier or cooker near the product. Otherwise, it may result in electric shock or fire.
It is important to give your eyes some rest (5 minutes every hour) when viewing the product screen for long periods of time. This will alleviate any eye strain.
Since the display panel is hot after using it for a long time, do not touch the product.
Keep small accessories away from the children.
Take care when adjusting the angle of the product or the height of the stand. If your hand or finger is caught, you may be injured. If the product is tilted excessively, the product may fall and this may result in injury.
Avoid placing a heavy object over the product. Otherwise, it may result in a problem with the product or injury.
Maintaining the Correct Posture when Using this Product
Maintain the correct posture when using this product. Straighten your back. Keep a distance of 45~50 cm from your eyes to the screen. Look down at the screen and face the screen forwards. Maintain the correct posture when using this product. Adjust the angle of the product so that light is not reflected onto the screen. Keep your elbow at a right angle and keep your arm level with the back of your hand. Keep your elbow at a right angle. Place your heels flat on the ground while keeping your knees at an angle of 90 degrees or higher and maintain the position of your arm so that your arm is below your heart.

Installing the Product

Package Contents
Unpack the product and check if all of the following contents have been included. Store the packaging box in case you need to move the Product at a later stage.

Monitor CONTENTS

Installation Manual

Product Warranty

D-Sub Cable

Power Cord

Cleaning Cloth

Cable Arrangement Link

Stand Connector

Stand OPTIONAL PARTS

DVI Cable
The cleaning cloth is supplied with black high-glossy models only.

Installing the Stand

Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. Insert the Stand Connector into the Stand in the direction shown by the figure.
Check if the Stand Connector is firmly connected.
Turn the connecting screw at the bottom of the stand fully so that it is completely fixed.
Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards.
Hold the main body of the product with your hand as shown by the figure. Push the assembled stand into the main body in the direction of the arrow as shown in the figure.

- Caution Do not lift the product holding only the stand

Removing the Stand

Before removing the stand, place the product down on a flat and stable surface so that the screen faces downwards. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product faces downwards.
Hold the main body of the product with your hand as shown by the figure. Pull the stand in the direction of the arrow as shown in the figure to separate it.
Turn the connecting screw at the bottom of the stand to separate it.
Take the Stand Connector out of the Stand by pulling it in the direction of the arrow as shown in the figure.
Installing the Stand for the Wall Mount
This product provides a stand mount of 75 mm x 75 mm that complies with the VESA specifications.
A. Stand Mount B. Stand (Optional) 1. Turn the product off and unplug the power cord from the wall outlet. 2. Place a soft cloth or cushion on a flat surface to protect the panel and place the product down on the cloth so that the front of the product faces downwards. 3. Separate the stand. 4. Align the groove of the part of the product that is to be connected to the stand with the groove in the stand (desk-top stand, wall mount stand or another stand) and firmly fix the stand by fastening the screw. If you use a screw that is longer than the standard specifications, the inside of the product may be damaged. For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ depending on the corresponding specifications. Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive force. This may result in damage to the product or injury due to the product falling. The company shall not be held liable for any damage or injury. The company shall not be held liable for any damage to the product or injury caused by using a stand that is not compatible with the specified specifications or due to an installation not performed by an authorized installation engineer. When installing the product using a wall mount, purchase a wall mount that provides at least 10 cm of space from the wall. The company shall not be held liable for any problems caused by using a stand that is not compatible with the specified specifications. Use the wall mount according to the international specifications.

Connecting with a PC

The connecting part may differ depending on the product model.
1. Connect the product to a PC depending on the video output supported by the PC. When the graphics card provides D-Sub (analog) output Connect the [RGB IN] port of the product to the [D-Sub] port of the PC with the D-Sub cable.
When the graphics card provides DVI (digital) output Connect the [DVI IN] port of the product to the DVI port of the PC with the DVI cable.
2. Connect one end of the power cord to the [POWER] port of the product and connect the other end of the power cord to the 220V or 110V wall outlet. (The input voltage is switched automatically.)
When the product is connected to a PC, you can turn the product on and use it. When both the DVI (<Digital>) and D-Sub (<Analog>) cables are connected, you can select the input signal <Analog/
Digital> by pressing the

button.

Kensington Lock
Kensington Lock A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, refer to the User Manual supplied with the locking device. You have to purchase an additional locking device.
Locking the product 1. Insert the locking part of the locking device into the hole of the Kensington lock of the product and turn it in the locking direction. 2. Connect the Kensington lock cable. 3. Tie the Kensington lock cable to a desk or heavy object. You can purchase the locking device from an electronics store, an online shop, or our service center.

Using the product

Setting the Optimal Resolution
If you turn the power on after purchasing the product, a message regarding the optimal resolution setting appears on the screen. Select a language and the optimal resolution.
/ : You can select a language with these buttons. MENU : If you press this button, the message disappears.
The message appears up to 3 times if the resolution has not been set to the optimal resolution. To set the resolution to the optimal resolution When the PC is turned off, connect the product and the PC and turn the power on. Right-click over the Desktop and select 'Properties' from the pop-up menu. In the 'Settings' tab, set the resolution to the optimal resolution.

Using this menu, you can change the intensity of the colors of medium brightness.
(This is unavailable when MagicBright is set to <Dynamic Contrast> mode.)

SIZE & POSITION

MENU H-Position
DESCRIPTION Moves the position of the display area on the screen horizontally. This function is only available in analog mode.

V-Position

Moves the position of the display area on the screen vertically. This function is only available in analog mode.

Image Size

PC signals <Auto> - The picture is displayed at the aspect ratio of the input signal. <Wide> - The picture is displayed in full screen regardless of the aspect ratio of the input signal. A signal not in the standard mode table is not supported. If the resolution is set to the optimal resolution, the aspect ratio does not change whether the <Image Size> is set to <Auto> or <Wide>.
AV signals <4 : 3> - Displays pictures at the 4 : 3 aspect ratio. <16 : 9> - Displays pictures at the 16 : 9 aspect ratio. <Screen Fit> - If a 720P, 1080i or 1080P signal is input in DVI input mode, the picture is displayed as is without truncation. This can only be set when the external input is connected through DVI and <PC/AV Mode> is set to <AV>. Menu H-Position Menu V-Position You can adjust the horizontal position of the OSD. You can adjust the vertical position of the OSD.

SETUP&RESET

MENU Reset
DESCRIPTION Use this function to restore the visual quality and color settings to the factory defaults. <No> - <Yes>

Menu Transparency

You can select the transparency of the OSD. <Off> - <On>
MENU Language Select a language for the OSD.
The selected language is only applied to the product OSD. This setting does not affect the other functions of the PC. LED On/Off Turns the Menu button LED on or off. LED Brightness Off Timer On/Off <Off> - Turns the Power button LED lamp off. <On> - Turns the Power button LED lamp on.
Adjusts the brightness of the Menu button LED in levels. You can turn the Off Timer on or off. <Off> - <On>
Off Timer Setting Auto Source
Turns the power off automatically when the configured time is reached. <Auto> - The monitor automatically selects an input signal. <Manual> - Users have to manually select an input signal.

PC/AV Mode

Set to PC when connected to a PC. Set to AV when connected to an AV device. This function does not support analog mode.

Display Time

The OSD automatically disappears if no action is taken by the user. You can determine the time to wait before the OSD is hidden. <5 sec> - <10 sec> - <20 sec> - <200 sec>

Customized Key

You can set the function of the Customized Key to one of the following. <MagicBright> - <MagicColor> - <Color Effect> - <Image Size>

INFORMATION

MENU INFORMATION
DESCRIPTION Shows the frequency and resolution set on the PC.

Installing the Software

Natural Color

What is Natural Color ?

This software works only for Samsung products and enables adjusting the displayed colors on the product and matches the colors on the product with the colors of the printed pictures. For more information, refer to the online help of the software (F1).
The Natural Color is provided online. You can download it from the website below and install; http://www.samsung.com/us/consumer/learningresources/monitor/naturalcolorexpert/pop_download.html

MagicTune

What is MagicTune?
MagicTune is a software program that helps with monitor adjustments by providing comprehensive descriptions of monitor functions and easy-to-understand guidelines. Users can adjust the product with the mouse and the keyboard without using the operating buttons of the product.
1. Insert the installation CD into the CD-ROM drive. 2. Select the MagicTune setup program. If the pop-up screen for the software installation does not appear on the main screen, find and double-click the MagicTune setup file on the CD-ROM. 3. Select the installation language and click [Next]. 4. Complete the remaining software installation steps according to the instructions displayed on the screen. The software may not work properly if you do not restart the computer after the installation. The MagicTune icon may not appear depending on the computer system and the product specifications. If the shortcut icon does not appear, press the F5 key.

Restrictions and Problems with the Installation (MagicTune)
The installation of MagicTunemay be affected by the graphics card, motherboard and the networking environment.

System Requirements

OS Windows 2000 Windows XP Home Edition Windows XP Professional Windows Vista For MagicTune, Windows 2000 or later is recommended. Hardware At least 32MB of memory At least 60MB of free space on the hard disk drive For more information, refer to the website.

Removing the Software

You can only remove MagicTunethrough [Add or Remove Programs ] in Windows. To remove MagicTune, complete the following steps. 1. Click [Start] select [Settings], and select [Control Panel] from the menu. For Windows XP, click [Start], and select [Control Panel] from the menu. 2. Double-click the [Add or Remove Programs] icon in the Control Panel.
3. In the [Add/Remove] window, find and select MagicTuneso that it is highlighted. 4. Click [Change or Remove Programs] to remove the software. 5. Select [Yes] to start removing MagicTune. 6. Wait until a message box appears informing you that the software has been removed completely. For technical support, the FAQ (frequently asked questions) or information about the software upgrade for MagicTune, please visit our website.

MultiScreen

What is MultiScreen ?
MultiScreen enables users to use the monitor by partitioning multiple sections.
1. Insert the installation CD into the CD-ROM drive. 2. Select the MultiScreen setup program. If the pop-up screen for the software installation does not appear on the main screen, find and double-click the MultiScreen setup file on the CD-ROM. 3. When the Installation Wizard appears, click [Next]. 4. Complete the remaining software installation steps according to the instructions displayed on the screen. The software may not work properly if you do not restart the computer after the installation. The MultiScreen icon may not appear depending on the computer system and the product specifications. If the shortcut icon does not appear, press the F5 key.
Restrictions and Problems with the Installation (MultiScreen)
The MultiScreen installation may be affected by the graphics card, motherboard and the networking environment.

Operating System

OS Windows 2000 Windows XP Home Edition Windows XP Professional Windows Vista For MultiScreen, the operating systems Windows 2000 or later is recommended. Hardware At least 32MB of memory At least 60MB of free space on the hard disk drive
Click [Start], select [Settings]/[Control Panel], and then double-click [Add or Remove Programs]. Select MultiScreen from the program list and click the [Add/Delete] button.

Troubleshooting

Monitor Self-Diagnosis
You can check if the product is working properly using the Self-Diagnosis function. If a blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected, perform the self-diagnosis function according to the procedures below.
1. Turn the product and the PC off. 2. Separate the D-Sub cable from the product. 3. Turn the product on. 4. If the product is working properly, the 'Check Signal Cable' message appears. In this case, if a blank screen is displayed again, make sure that there is no problem with the PC and the connection. The product is working properly.
Before Requesting Service
Please check the following before requesting After-Sales service. If the problem continues, please contact your nearest Samsung Electronics Service Center. A BLANK SCREEN APPEARS / I CANNOT TURN THE PRODUCT ON
Is the power cord connected properly? Is the Check Signal Cable message displayed on the screen?
Check the connection status of the power cord. Check the cable connecting the PC and the product. If the message appears on the screen even if the cable is properly connected, recheck the input signal by pressing the button of the product. This occurs when the signal from the graphics card exceeds the maximum resolution or the maximum frequency of the product. In this case, set up the appropriate resolution and the frequency for the product.
Is the Not Optimum Mode message displayed on the screen?
Is a blank screen displayed and does the power LED blink at a 1 second interval?
This occurs when the power saving function is running. If you click the mouse or press any key, the screen will be turned on. If you connect the DVI cable when the PC has booted up or if you reconnect the DVI cable after disconnecting the cable while using a PC, the screen may not be displayed because some graphics cards do not output the video signal. In this case, reboot the PC while the DVI cable is connected.
Did you connect with a DVI cable?
THE ON SCREEN ADJUSTMENT MENU (OSD) DOES NOT APPEAR. Did you cancel the screen adjustment? Check if the <OSD Adjustment Lock> function is set to Off.
THE COLOR IS WEIRD / THE PICTURE IS DISPLAYED IN BLACK AND WHITE Is the entire screen displayed in the same color as if viewing the screen through a cellophane paper? Check the cable connection to the computer. Reinsert the graphics card into the computer completely. Check if the <Color Effect> is set to <Off>. Is the graphics card configured correctly? Set up the graphics card referring to the user manual.

THE DISPLAY AREA SUDDENLY MOVES TO AN EDGE OR TO THE CENTER. Did you change the graphics card or the driver? Did you change the resolution and frequency appropriate to the product? Please press the [AUTO] button to run the auto adjustment function. Set the resolution and the frequency to the appropriate values in the graphics card refer to the (Standard Signal Mode Table) Is the graphics card configured correctly? Set up the graphics card referring to the user manual. THE PICTURES ARE OUT-OF-FOCUS. Did you change the resolution and the frequency appropriate to the product? Set the resolution and the frequency to the appropriate values in the graphics card refer to the (Standard Signal Mode Table)
THE COLOR IS DISPLAYED IN 16 BIT (16 COLORS). THE COLOR HAS BEEN CHANGED AFTER CHANGING THE GRAPHICS CARD. Did you install the device driver for the product? Windows ME/XP/2000 : Set the color again by selecting Control Panel Display Settings. Is the graphics card configured correctly? Configure the color again in accordance with the new graphics card driver.
WHEN I CONNECT THE MONITOR, THE 'UNKNOWN MONITOR, PLUG&PLAY (VESA DDC) MONITOR FOUND' MESSAGE IS DISPLAYED. Did you install the device driver for the product? Check if all the Plug&Play (VESA DDC) functions are supported referring to the User Manual of the graphics card. Install the device driver referring to the descriptions about the driver installation. Install the device driver referring to the descriptions about the driver installation.
WHEN I LOOK AT THE EXTERIOR EDGES OF THE PRODUCT, SMALL ALIEN SUBSTANCES APPEAR ON IT. Since this product is designed so that the color has a soft appearance by coating it with a transparent material over the black edges, such things may be seen. This is not a defect of the product. A BEEP, BEEP SOUND IS HEARD WHEN BOOTING THE COMPUTER. If the beep sound is generated 3 or more times when booting up the computer, please request service for the computer.
FAQ! PLEASE TRY THE FOLLOWING! You have to change the frequency of the graphics card. (For more information, refer to the User Manual of the computer or the graphics card.)

449 x 314 x 66 mm / 17.7 x 12.4 x 2.6 inch (Without Stand) 449 x 384 x 190 mm / 17.7 x 15.1 x 7.5 inch / 4.3 kg / 9.5 Ibs (With Stand)
486.6 x 308.3 x 65 mm / 19.2 x 12.1 x 2.6 inch (Without Stand) 486.6 x 377.3 x 189.4 mm / 19.2 x 14.9 x 7.5 inch / 4.4 kg / 9.7 Ibs (With Stand)
518.2 x 327.7 x 66 mm / 20.4 X 12.9 X 2.6 inch (Without Stand) 518.2 x 396.7 x 189.4 mm / 20.4 X 15.6 X 7.5 inch / 4.4 kg / 9.7 Ibs (With Stand)
555.8 x 345.0 x 63.8 mm / 21.9 X 13.6 X 2.5 inch (Without Stand) 555.8 x 416.2 x 189.4 mm / 21.9 X 16.4 X 7.5 inch / 5.1 kg / 11.2 Ibs (With Stand)
Environmental considerations Tilt

Operating

Temperature : 50F ~ 104F (10C ~ 40C) Humidity : 10 % ~ 80 %, non-condensing

Storage

Temperature : -4F ~ 113F (-20C ~ 45C) Humidity : 5 % ~ 95 %, non-condensing -2 ~ 21
Class B (Information Communication equipment for residential use) This device has been registered regarding EMI for home use (Class B). It may be used in all areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

Power Saving Function

This product provides a power saving function that automatically turns the screen off when the product is not used for a predetermined period of time to reduce power consumption. If the product enters power saving mode, the power LED turns to a different color to indicate that the product is in power saving mode. When the product is in power saving mode, the power is not turned off and you can turn the screen on again by pressing any key or clicking the mouse. However, the power saving function only works when the product is connected to a computer that provides the power saving function. STATE Power Indicator NORMAL OPERATION On P1950W : 34 watts Power Consumption P2050 / P2050G : 34 watts P2250 / P2250G : 38 watts P2350 / P2350G : 40 watts Less than 1 watts Less than 1 watts POWER SAVING MODE Blinking POWER OFF Off
If there is no power cut-off switch, the power consumption is "0" only when the power cord is disconnected.

ASIA PACIFIC PHILIPPINES 1800-10-SAMSUNG(726-7864) 1800-3-SAMSUNG(726-7864) 02-5805777 SINGAPORE THAILAND 1800-SAMSUNG(726-7864) 1800-29-3232 02-689-3232 TAIWAN VIETNAM 0800-329-889 MIDDLE EAST & AFRICA SOUTH AFRICA TURKEY U.A.E 0860-SAMSUNG(726-7864) 11 800-SAMSUNG(726-7864) 8000-4726 http://www.samsung.com/za http://www.samsung.com/tr http://www.samsung.com/ae http://www.samsung.com/tw http://www.samsung.com/vn http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/ph
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

SyncMaster T200HD/T220HD

LCD Monitor

User Manual

Safety Instructions

Notational

Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.

Notational Conventions

Prohibited
Important to read and understand at all times Disconnect the plug from the outlet Ground to prevent an electric shock

Do not disassemble

Do not touch
When not used for extended period of time, set your computer to DPM. If using screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries). Shortcut to Anti-Afterimage Instructions Do not use a damaged power cord or plug or a damaged or loose power outlet. Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or plugging the plug into the outlet. Otherwise, this may result in electric shock. Make sure to connect the power cord to a grounded power outlet. Otherwise, it may result in electric shock or personal injury.
Ensure that the power plug is plugged into the power outlet firmly and correctly. Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place any heavy material on it. Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product. Otherwise, this may result in damage to the product due to electric shock.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the provided power cord of another product. Otherwise, this may result in fire or electric shock.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it.
Ensure that at least two persons lift and move the product. Otherwise, it may be dropped and cause personal injury, and/or damage the product.
When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out. Otherwise, it may fall or cause personal injury. Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. Otherwise, this may result in fire.

When cleaning the product, do not spray water directly onto the main body of the product. Ensure that water does not enter the product and that it is not wet. Otherwise, this may result in electric shock, fire or a malfunction.

Others

The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves. Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. Otherwise, this may result in electric shock or fire.
If thunder or lightening is occurring, do not touch the power cord or antenna cable. Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or curtain. Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product. If water or a foreign material enters the product, disconnect the power cord and contact a Service Center. This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the product. Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). If water or foreign material enters the product, disconnect the power cord and contact a Service Center. Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may occur. If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver. Set a resolution and frequency appropriate to the product. Otherwise, your eyesight may be damaged.

Unpacking

Without stand

With stand

Monitor Manuals

Monitor

Quick Setup Guide
Warranty Card (Not available in all locations)

User's Guide

Cables
D-Sub Cable Sold separately

Power Cord

Stereo Cable

DVI Cable

HDMI Cable

Headphones

Sold separately

USB Cable

TV Antenna Cable (Coaxial Cable)
Component(PR, PB, Y) Cable

Audio cable

Digital audio optic output cable
Remote Control BN59-00678A
Batteries (AAA X 2) (Not available in all locations)

Cleaning Cloth

Cable holding ring Note

Stand Body

Stand Base
Cleaning Cloth is only provided for highly polished black products as a product feature.

Your Monitor Front

Activates a highlighted menu item. Push the ' ', button to change the input signal source.
Changing the source is only allowed for external devices connected to the product at the time. To switch Screen modes: [PC] [DVI] [TV] [Component] [HDMI1] [HDMI2] >> Click here to see an animation clip MENU Use this button to open the on-screen menu and to exit from the on-screen menu or to close the screen adjustment menu. - VOL+ Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. - CH + Moves from one menu item to another vertically or adjusts selected menu values. In TV/DTV mode, selects TV/DTV channels. Power button [ ]
Use this button for turning the product on and off.
Note The button to the right of the monitor are touch-sensitive buttons. Touch a button lightly with your finger. Power indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Speaker
Note The configuration at the back of the product may vary from product to product.
POWER POWER Connect the power cord for your monitor to the POWER port on the back of the product.
PC Connect the PC terminal at the back of your monitor to your computer.
HDMI/PC/DVI-D AUDIO IN DIGITAL AUDIO OUT(OPTICAL) EX-LINK HDMI/PC/DVI-D AUDIO IN Connect the [ HDMI/PC/DVI-D AUDIO IN ] terminal at the back of your product to your computers sound card. DIGITAL AUDIO OUT(OPTICAL) Connect the [DIGITAL AUDIO OUT(OPTICAL)] terminal of your product to the digital sound output or standard sound output terminal of the DVD home theater (or amplifier) using a digital audio optical output cable. EX-LINK This is a reserved terminal used for servicing. SERVICE SERVICE This is a reserved terminal used for servicing.

Connections 2. Connecting Using a DVI to HDMI Cable
Connect the DVI output terminal of a digital output device to the [HDMI IN 1] terminal of the monitor using a DVI to HDMI cable. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the [HDMI/PC/DVI AUDIO IN]terminal of the monitor. 3. When all the connections are completed, connect the power cords for the monitor and DVD (or the device connected to the digital output terminal). 4. Select "HDMI" using the 'SOURCE [ Note If you just connect using the DVI to HDMI cable without connecting to the sound source, you cannot hear sound. Connecting the audio output terminal of a digital device to the [R-AUDIO-L] of [COMPONENT IN] of the monitor using an audio cable will not give you sound. Make sure to connect to the [ HDMI/PC/DVI-D AUDIO IN ] terminal of the monitor. ]' button.
Connecting and Using an Amplifier
Note You can connect the digital sound input (optical) or standard sound input terminal of your amplifier to your monitor using the correct cable.
Connect the [DIGITAL AUDIO OUT (OPTICAL)] terminal of your monitor to the digital sound input terminal of your digital amplifier using an optical cable.
Connections 2. 3. 4. Set the Internal Mute On in the Sound menu using the MENU button. Adjust the sound volume using the Volume button of your amplifier If the connections are set up, power up your monitor and amplifier. Note If no sound is emitted from the monitor, you need to use an amplifier. For information on how to connect a speaker and amplifier, refer to the respective user manuals provided by their manufacturers.

Connecting Headphone

Note You may connect your headphones to the monitor.
Connect your headphones to the Headphone connection terminal.
Using the Stand Monitor Assembly

Monitor and Bottom

Tilt angle
Note You can tilt the monitor upwards at an angle of -1 to 21.

Using the Software

Monitor Driver
Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide)
Installing the Monitor Driver (Automatic)
1. 2. 3. Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.

If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button (Microsoft Windows XP/2000 Operating System).
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft Windows Vista Operating System 1. 2. Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
Click "Personalization" and then "Display Settings".
Click "Advanced Settings.".
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs." is displayed, as shown in the figure below, click "Continue".
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver." in the "Driver" tab.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Click "Have Disk. and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Select the model that matches your monitor from the list of monitor models on the screen, and click "Next".
10. Click "Close" "Close" "OK" "OK" on the following screens displayed in sequence.
Microsoft Windows XP Operating System
Using the Software 1. 2. Insert CD into the CD-ROM drive. Click "Start" "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced.".
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Click "Update Driver." and select "Install from a list or." then click "Next" button.
Select "Don't search, I will." then click "Next" and then click "Have disk".

Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed. Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. 2. 3. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install 1. 2. 3. 4. Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Choose "Monitor". Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. 5. 6. 7. 8. 9. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button. Microsoft Windows Millennium Operating System 1. 2. 3. Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings" tab and click "Advanced Properties" button.
Using the Software 4. 5. 6. 7. 8. 9. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location." then click "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK" button.

How to delete the Natural Color software program
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the "Add/Delete" button.

Adjusting the Monitor

Picture Available Modes
PC / DVI TV Component HDMI Note The default setting may be different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.
Picture : PC / DVI MagicBright
MagicBright is a feature providing optimum viewing environment depending on the contents of the image you are watching. Currently five different modes are available: Entertain, Internet, Text, Dynamic Contrast and Custom. Each mode has its own pre-configured brightness value. Entertain High Brightness For watching motion pictures such as a DVD or VCD Internet For working with a mixture of images such as texts and graphics. Text For documents or works involving heavy text. Dynamic Contrast
Adjusting the Monitor Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu. MENU , MENU,EXIT
Contrast / Brightness / Sharpness
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the contrast and brightness according to personal preference. Contrast : Adjust the Contrast. Brightness : Adjust the Brightness. Sharpness : Adjust the Sharpness. , , , , MENU,EXIT

Auto Adjustment

The values of Fine, Coarse and Position are adjusted automatically.
Adjusting the Monitor By changing the resolution in the control panel, auto function is performed. (Available in PC Mode Only) MENU , MENU,EXIT
Screen : (Available in PC mode only) - Coarse / Fine
Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.

Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).

MENU,EXIT

- Position
Adjusts the screen location horizontally and vertically. MENU , , , , , MENU,EXIT

- Image Reset

Image parameters are replaced with the factory default values. MENU , , MENU,EXIT

- Resolution

Displays the resolution set on the PC.
Picture Options - Color Tone
Adjusting the Monitor The tone of the color can be changed. (Available in PC / DVI mode only) Cool / Normal / Warm / Custom MENU , , MENU,EXIT
- R-Gain / G-Gain / B-Gain
Adjusts the individual R, G, B color controls. MENU , , , , , MENU,EXIT

- Size

You can switch the Size. Wide / 4:3 MENU , , , MENU,EXIT
Picture parameters are replaced with the factory default values. OK Cancel , , MENU,EXIT
Picture : TV / Component / HDMI Mode
The Monitor has three automatic picture settings ("Dynamic", "Standard", and "Movie") that are preset at the factory. You can activate either Dynamic, Standard, or Movie. Dynamic Selects the picture for high-definition in a bright room. Standard Selects the picture for optimum display in a normal environment. Movie Selects the picture for viewing movies in a dark room.
Backlight / Contrast / Brightness / Sharpness / Color / Tint
You can use the on-screen menus to change the contrast and brightness according to personal preference. Backlight : Adjust the screen brightness by adjusting the LCD backlight. Contrast : Adjust the Contrast. Brightness : Adjust the Brightness. Sharpness : Adjust the Sharpness. Color : Adjusts the picture color. Tint : Adds a natural tone to the display. , , , , MENU,EXIT
The tone of the color can be changed. Cool1 / Cool2 / Normal / Warm1 / Warm2
Note Warm1 or Warm2 is only activated when the picture mode is Movie. Settings can be adjusted and stored for each external device you have connected to an input of the TV. MENU , , MENU,EXIT
You can switch the Size. The direct button on the remote control is 'P.SIZE' button. Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. 16:9 - Sets the picture to 16:9 wide mode. Zoom1 - Magnifies the size of the picture on the screen. Zoom 2 - Magnifies the size of the picture more than Zoom1. Wide Fit - Enlarges the aspect ratio of the picture to fit the entire screen. 4:3 - Sets the picture to 4:3 normal mode. Just Scan - Use the function to see the full image without any cut off when HDMI (480i / 1080i), Component (480i / 1080i) or DTV(480i / 1080i) signals are input. ( Wide Fit and Just Scan are only operated in HDMI mode.) MENU , , , MENU,EXIT

TV Speaker

If you set this menu "On", sound output from the speakers is muted in case of using the home theater. Off On , , , MENU,EXIT

Channel Available Modes

PC / DVI TV Component HDMI Note The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.

Antenna

Adjusting the Monitor You can select a normal or wired channel. If ANT IN are connected, select the antenna input you want. If the antenna input is not selected properly, noise may appear on the screen. Air Cable , , MENU,EXIT

Auto Program

The TV automatically cycles through all of the available channels and stores them in memory. In rare cases, "Auto program" may miss a few channels due to weak signals and the channels may not be added to the channel memory. Air Cable Auto , , , , , , MENU,EXIT

Clear Scrambled Channel

Adjusting the Monitor The Clear Scrambled Channel function is used to filter out scrambled channels after "Auto Program" is completed. It removes the scrambled channels from the list by tuning the digital cable channels. This process may take up to 20~30 minutes. (Available in Digital Cable TV Mode Only) MENU , , MENU,EXIT

Channel List

You can manage the channels.

MENU , MENU,EXIT

Note All selected channels will be shown on Added menu. , , , ,

MENU , MENU,EXIT

Favorite
Note Only memorized channels can be set as favorite channels. All favorite channels will be shown in the Favorite menu. , , , ,
If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required. (Available in Analog TV Mode Only) MENU , , , , , , , MENU,EXIT

Fine Tune

Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. (Available in Analog TV Mode Only) MENU , , , , MENU,EXIT

Signal Strength

Check List

Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
1. Problems related to Installation
Note Problems related to the monitor installation and their solutions are listed.

PC Mode

Q: A: Q: A: It appears the PC does not function normally. Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) The monitor screen flickers. Check if the signal cable between the computer and the monitor is securely connected and tightened.(Refer to Connecting the monitor)

TV Mode

Q: A: Q: A: TV screen is blurred or shows noise signals. Check if the TV antenna connector is securely connected to the external antenna.(Refer to Connecting TV) TV signal is not received Select "Auto Program" to configure the channel system automatically. (Refer to the Auto Program)
2. Problems related to Screen
Note Problems related to the monitor screen and their solutions are listed. Q: A: Q: A: A: Q: A: A: Q: A: Q: A: A: A: Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on.(Refer to the Connecting the monitor) "Check Signal Cable" message Ensure that the signal cable is firmly connected to the PC or video SOURCEs.(Refer to the Connecting the monitor) Ensure that the PC or video SOURCEs are turned on. "Not Optimum Mode" message Check the maximum resolution and the frequency of the video adapter. Compare these values with the data in the Preset Timing Modes Chart. Picture rolls vertically. Check if the signal cable is securely connected.Connect it again securely. (Refer to Connecting the monitor) Image is not clear. Picture is blurred. Run Frequency Coarse and Fine tuning. Turn on again after removing all accessories (video extension cable, etc.) Set resolution and frequency to the recommended ranges.
Troubleshooting Q: Picture image is unstable and vibrates. Ghost images are shown in the picture. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the monitor.If not, reset them referring to the current Information under the monitor menu and Preset Timing Modes. The image is too light or too dark Adjust the Brightness and Contrast.(Refer to the Brightness, Contrast) The Power Indicator blinks. The monitor is currently saving the changes made in settings to the OSD memory. The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The monitor is using its power management system. press a key on the keyboard. The screen is blank and is blinking. If you see the "TEST GOOD" message on the screen when you press the MENU button, check the cable connection between the monitor and the computer to ensure that the connector is properly connected.

Q: A: Q: A: Q: A: A: Q: A:
3. Problems related to Audio
Note Problems related to audio signals and their solutions are listed below. Q: A: A: Q: A: A: No sound Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card.(Refer to the Connecting the monitor) Check the volume level.(Refer to the Volume) The sound level is too low. Check the volume level.(Refer to the Volume) If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.
4. Problems related to Remote Control
Note Problems related to the remote control and their solutions are listed. Q: A: A: A: The remote control buttons do not respond. Check the battery polarities (+/-). Check if the batteries have been exhausted. Check if the power is on.
Troubleshooting A: A: Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity
5. You may see small particles if you look closely at the edge of the bezel surrounding the screen.
This is part of the products design and is not a defect.

Q&A

Q: A: A: Q: A: How can I change the frequency? The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjusts the resolution? Windows XP: Set the resolution in the Control Panel Appearance and Themes Display Settings. A: Windows ME/2000: Set the resolution in the Control Panel Display Settings. * Contact the video card manufacturer for details. Q: A: How can I set the Power Saving function? Windows XP: Set the resolution in the Control Panel Appearance and Themes Display Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows ME/2000: Set the resolution at the Control Panel Display Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Q: A: How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the monitor. Q: A: What are the benefits of digital broadcasting? Digital TV broadcasting generates less noise and provides clearer visuals and sound than analog TV broadcasting does. As services develop, you can also enjoy various information services because various kinds of data besides video and audio can be sent. For example, while watching a sports game, you can view various data on your favorite player or you can view all or selected screens which have been captured from different angles for a

This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 68.681 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 65.290 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.062 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.954 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 100.000 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.000 108.000 108.000 135.000 146.250 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ +/+ -/+
IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 960 VESA, 1280 x 1024 VESA, 1280 x 1024 VESA, 1680 x 1050
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: Hz
General Model Name LCD Panel Size 22 inch (55 cm) SyncMaster T220HD
LCD Panel Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.2M Resolution Optimum resolution Maximum resolution 1680 x 1050 @ 60 Hz 1680 x 1050 @ 60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 473.76 mm (H) x 296.1 mm (V) 0.282 mm (H) x 0.282 mm (V)
Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) 0.7 Vp-p 5 % separate H/V sync, Composite TTL level (V high 2.0 V, V low 0.8 V) Maximum Pixel Clock 146.250 MHz (Analog, Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Dimensions (W x H x D) / Weight 520 x 373.5 x 86.5 mm / 20.5 X 14.7 X 3.4 inch (Without Stand) 520 x 441.5 x 215 mm / 20.5 X 17.4 X 8.5 inch (With Stand) / 6.2 kg / 13.7 Ibs Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4 F ~ 113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor

Plug and Play Capability settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 5,292,000. Note Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. State Power Indicator Normal Operation Power saving mode Power off (Power button) EPA/ENERGY 2000 On Blinking Less than 2 watts Off Less than 1 watts
Power Consump- Less than 58 watts tion
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) 31.469 Vertical Frequency (Hz) 70.086 Pixel Clock (MHz) 25.175 Sync Polarity (H/V) +/-