Ofrecido por www.electromanuales.com
Washing Machine Owners Instructions
WF-J145N(V/C/S) WF-J125N(V/C/S) WF-J105N(V/C/S) WF-J85N(V/C/S) WF-B145N(V/C/S) WF-B125N(V/C/S) WF-B105N(V/C/S) WF-B85N(V/C/S) WF-R125N(V/C/S) WF-R105N(V/C/S) WF-R85N(V/C/S) WF-F125N(V/C/S) WF-F105N(V/C/S) WF-F85N(V/C/S)
Register your product at www.samsung.com/global/register

Safety Precautions

Congratulations on your purchase of this Samsung washing machine. These Owner's Instructions contain valuable information on the installation, use, and care of this appliance. Please take the time to read these instructions so that you can take full advantage of the washing machine's features and enjoy this appliance for many years to come.
Before using the appliance
Packing materials can be dangerous to children; keep all packing material (plastic bags, polystyrene, etc.) well out of the reach of children. The appliance is designed for home use only. Make sure that water and electrical connections are made by qualified technicians, observing the manufacturer's instructions (see "Installing the Washing Machine") and local safety regulations. All packaging and shipping bolts must be removed before the appliance is used. Serious damage may occur if they are not removed. See "Removing the shipping bolts". Before washing clothes for the first time, you must run a complete cycle without clothes. See "Washing for the first time". Before cleaning or carrying out maintenance, unplug the appliance from the electrical outlet or set the (On/Off) button to Off. Make sure that the pockets of all clothing to be washed are empty. Hard, sharp objects, such as coins, safety pins, nails, screws, or stones can cause extensive damage to the appliance. Always unplug the appliance and turn off the water after use. Before you open the door of the appliance, check that the water has drained. Do not open the door if you can still see water. Pets and small children may climb into the appliance. Check the appliance before each use. The glass door becomes very hot during the washing cycle. Keep children away from the appliance while it is in use. Do not attempt to repair the appliance yourself. Repairs made by inexperienced or unqualified persons may cause injury and/or make more serious repairs to the appliance necessary. If the plug (power supply cord) is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This appliance should only be serviced by an authorized service center, and only genuine spare parts should be used. This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure that they do not play with the appliance. This appliance has to be connected to the plug endurable to proper power consumption. This appliance has to be positioned so that the plug is accessible after installation. Do not use processed water containing oil, cream or lotion, which is usually found in skin-care shops or massage clinics. Otherwise this will cause the packing to be deformed, which causes a malfunction or water leak. A stainless washing tube does not usually rust. However if some metal such as a hair pin is left in the tube for an extended time, the tube could rust. Do not leave water or bleach containing chlorine in the tube for an extended period of time. Do not regularly use or leave water containing iron in the tube for an extended period of time. If rust starts appearing on the surface of the tube, apply a cleansing agent (neutral) to the surface and use a sponge or soft cloth to clean it. (Under no circumstances use a metal brush)

Safety instructions

SAVE THESE INSTRUCTIONS

Table of Contents

Safety Precautions. inside cover Installing the Washing Machine.2
Unpacking the Washing Machine. 2 Overview of the washing machine. 2 Selecting a location. 3 Adjusting the leveling feet. 3 Removing the shipping bolts. 3 Connecting the water supply hose(Option). 3 Connecting the water supply hose. 4 Positioning the drain hose. 4 Plugging in the machine. 5
Washing a Load of Laundry
Overview of the control panel. 6 Washing for the first time. 8 Putting detergent in the washing machine. 8 Washing clothes using Fuzzy Logic. 9 Washing clothes manually.10 Using Delay Start.10 Washing tips and hints.11
Maintaining the Washing Machine.12
Draining the washing machine in an emergency.12 Repairing a frozen washing machine.12 Cleaning the exterior.12 Cleaning the detergent drawer and recess.13 Cleaning the debris filter.13 Cleaning the water hose mesh filter.14

Troubleshooting.15

Problems and solutions.15 Understanding error messages.15
Programme Chart.16 Appendix.18
Fabric care chart.18 Electrical warnings.18 Protecting the environment.19 Declaration of conformity.19 Specification.19
SAMSUNG Washing Machine Owners Instructions
Installing the Washing Machine
Unpacking the Washing Machine
Unpack your washing machine and inspect it for shipping damage. Also make sure that you have received all of the items shown below. If the washing machine was damaged during shipping or you do not have all of the items, contact your Samsung dealer immediately.
Overview of the washing machine

Worktop

Detergent drawer Control panel Drain Hose

Door Plug

Base cover Adjustable feet Debris filter Emergency drain tube Filter-cover
Cold Water supply hose Wrench Drain hose

Hose guide

Bolt hole covers
2 SAMSUNG Washing Machine Owners Instructions

Selecting a location

Before you install the washing machine, select a location with the following characteristics:
A hard, level surface (if the surface is uneven, see "Adjusting the leveling feet," below) Away from direct sunlight. Adequate ventilation Room temperature that will not fall below 0 C Away from sources of heat such as coal or gas

Make sure that the washing machine does not stand on its power cord. Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
Adjusting the leveling feet
If the floor is uneven, adjust the feet (do not insert pieces of wood or any other objects under the feet):
1. Loosen the leg bolt by turning it with your hand until it is at the desired height. 2. Tighten the locking nut by turning it with the supplied wrench.
Place the washer on a sturdy, flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Only a l degrees angle is allowed.)
Removing the shipping bolts
Before using the washing machine, you must remove the five shipping bolts from the back of the unit. To remove the bolts:

1. 2. 3. 4.

Loosen all bolts with the supplied wrench before removing them. Take each bolt head and pull it through the wide part of the hole. Repeat for each bolt. Fill the holes with the supplied plastic covers. Keep the shipping bolts for future use.
Connecting the water supply hose(Option)
1. Remove the adaptor from the water supply hose.
4. Connect the water supply hose to the adaptor. Pull down part (c) of the water supply hose. When you release part (c) the hose automatically connects to the adaptor making a click sound. 5. Connect the other end of the water supply hose to the inlet water valve at the top of the washer. Screw the hose clockwise all the way in.
2. First, using a + type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow until there is a 5mm gap. 3. Connect adaptor to the water tap by tightening the screws firmly. Then, turn part (b) following the arrow and put(a) and (b) together.
If the water tap has a screw type faucet, connect the water supply hose to the tap as shown.
NOTICE After completing connection, if water leaks from the hose, then repeat the same steps.
Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.
SAMSUNG Washing Machine Owners Instructions 3
Connecting the water supply hose

The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high pressure hose. To connect the water supply hose:
1. Take the L-shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine. Tighten by hand.
2. Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing machine end by loosening the fitting, rotating the hose, and retightening the fitting.

Option:

1. Take the red L-shaped arm fitting for the hot water supply hose and connect to the red hot water supply intake on the back of the machine. Tighten by hand. 2. Connect the other end of the hot water supply hose to your sink's hot water faucet and tighten it by hand. 3. Use a Y-piece if you only want to use cold water.
Note: The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.
Positioning the drain hose
The end of the drain hose may be positioned in three ways:

Over the edge of a sink

The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving.
ln a sink drain pipe branch
The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground.

ln a drain pipe

Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm.
4 SAMSUNG Washing Machine Owners Instructions

Plugging in the machine

You MUST ground the plug of the washing machine. Check with a licensed electrician before using the machine to make sure it is properly grounded.

For U.K. Users.

Wiring lnstructions
WARNING THIS APPLIANCE MUST BE EARTHED. This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of electric shock providing an escape wire for the electric current. The appliance is equipped with a mains lead which includes an earth wire for connecting to the earth terminal of your mains plug. The plug must be plugged into a socket that is properly installed and earthed. * The wires in this mains lead are coloured in accordance with the following code:

Green and yellow : Earth Blue : Neutral Brown : Live

GREEN AND YELLOW

13 AMP FUSE
AS the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the terminals in your plug, proceed as follows. Connect the green and yellow wire to the terminal in the plug marked with the letter E or the earth symbol ( ) or coloured green or green-andyellow. Connect the blue wire to the terminal marked with the letter N or coloured black. Connect the brown wire to the terminal marked with the letter L or coloured red. * Consult a qualified electrician or service technician if in doubt about any of these instructions. The manufacturer of this washing machine will not accept any liability for damage to persons or material for non observance of these requirements. There are no user serviceable parts inside the washing machine and if the mains lead of this appliance is damaged, it must only be replaced by qualified service personnel approved by the manufacturer because special tools are required.

BLUE WARNING

Ensure that the plug and power cord are not damaged before use. If you have any reason to remove the moulded plug from this appliance, immediately remove the fuse and dispose of the plug. Do not connect the plug to a mains socket under any circumstances as there is a danger of electric shock.

CIRCUITS

Your washing machine should be operated on a separate circuit from other appliances. Failure to do this may cause the circuit breaker to trip or the fuse to blow.
Overview of the control panel
1. Digital graphic display
Displays the remaining wash cycle time,all of washing information and error messages.

2. Wash selection button

Press the button to select wash. Wash is available only with Baby Cotton, Heavy Soil, Mixed Load, Calm Wash, Cotton, Coloureds, Synthetics, Delicates.
3. Temperature selection button
Press the button repeatedly to cycle through the available water temperature options (cold water( ), 30 C, 40 C , 60 C and 95 C).
4. Rinse selection button
Press the rinse button to add rinse cycles. Maximum number of rinse cycles is five.

5. Spin selection button

Press the button repeatedly to cycle through the available spin speed options. WF-J145N/WF-B145N WF-J125N/WF-B125N/WF-R125N/WF-F125N WF-J105N/WF-B105N/WF-R105N/WF-F105N WF-J85N/WF-B85N/WF-R85N/WF-F85N Rinse hold, Rinse hold, Rinse hold, Rinse hold, , 400, 800, 1200, 1400 rpm , 400, 800, 1000, 1200 rpm , 400, 600, 800, 1000 rpm , 400, 600, 800 rpm : no spin,

No spin

The laundry remains in the drum without being spun after the final drain

Rinse Hold

The laundry remains soaking in the final rinse water. Before the laundry can be unloaded, either Drain or the Spin program must be run.

6. Delay Start selection button
Press the button repeatedly to cycle through the available delayed start options (from 4 hour to 24 hours in one hour increments). Displayed hours means the time of finished washing-cycle.
6 SAMSUNG Washing Machine Owners Instructions
7. Silver Nano selection button
Silver Nano water is supplied in washing as well as the last rinse, featuring sterilization and antibacterial coating.
8. Child Lock selection button
This is a button for preventing children from manipulating the washing machine. On/Off - To set the program on: Press the Start/Pause button to turn on the washing machine. Press and hold down the [Rinse] + [Spin] button for 2-3 seconds. It can only be activated when the machine is turned on. Once you set the Child Lock function while in washing, no button is activated until you set it off. Only POWER button can activate. The Child Lock lamp lights on and off. To set the program off: Press and hold down the [Rinse] + [Spin] button again for 2-3 seconds, then the lamp lights off and is set off. Note: Check out the Baby Program button first when no button is activated while the washing machine is working.

9. Fuzzy Control dial

Turn the dial to select one of the 14 available wash programs. Cotton, Coloureds, Synthetics, Delicates, Wool, Hand wash, Quick, Rinse+Spin, Spin, Drain, Baby Cotton, Heavy Soil, Mixed Load, Calm Wash
10. Start/Pause selection button
Press to pause and restart programs. Press the Start/Pause button before adding the laundry. This can only be selected within 5 minutes of the start.
(On/Off) selection button
Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any buttons being touched, the power automatically turns off.
Washing for the first time
Before washing clothes for the first time, you must run a complete cycle without clothes. To do this:
1. Press the (On/Off) button. 2. Pour a little detergent into compartment in the detergent drawer. 3. Turn on the water supply to the washing machine. 4. Press the Temperature button repeatedly until 40 C is displayed. 5. Press the Start/Pause button. This will remove any water from the manufacturers test run remaining in the machine.
Dispender Dispenser Dispenser

:Detergent for prewash or starch. : Detergent for main wash, water softener,pre-soaking agent, bleach and stain removal product. : Additives,e.g.fabric softener or former (fill no higher than lower edge of insert A)
Putting detergent in the washing machine
1. 2. 3. 4. Pull out the detergent drawer. Add laundry detergent into compartment. Add softener into compartment (if you desire). Add prewash detergent into compartment (if you desire).
Caution : Concentrated or thick fabric softener and conditioner must be diluted with a little water before being poured into the dispenser (prevents the overflow from becoming blocked.)
8 SAMSUNG Washing Machine Owners Instructions
Washing clothes using Fuzzy Logic
Your new washing machine makes washing clothes easy, using Samsung's "Fuzzy Logic" automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed. To wash clothes using the Fuzzy Logic programs:
1. 2. 3. 4. 5. 6. Turn on your sink's water faucet. Press the (On/Off) button. Open the door. Load the articles one at a time loosely into the drum, without overfilling. Close the door. Add the detergent, softener, and wash detergent (if necessary) into the appropriate compartment.
7. Turn the Fuzzy Control dial to select the appropriate program for the type of clothes Cotton, Coloureds, Synthetics, Delicates, Wool, Hand wash, Quick, Rinse+Spin, Spin, Drain, Baby Cotton, Heavy Soil, Mixed Load, Calm Wash. You will see the indicators light up on the control panel.
Note: Wash is only available when washing Duvet, Bedding, Towel, Curtain, Cotton, Coloureds, Synthetics and Delicates programs. It is only necessary if your clothing is heavily soiled.
8. At this time, you can control the wash temperature, rinsing times, spin speed, delay time by pressing the appropriate option button. 9. Press the Start/Pause button on the Fuzzy Control dial and the wash cycle will begin. The process indicator will light up and the remaining time for the cycle will appear in the display.

When the cycle is finished:
After the total cycle has finished, the power will turn off automatically.

1. Open the door.

Note: The door will not open untill 3 minutes after the machine stops or the power turns off.

2. Remove laundry.

Washing clothes manually
You can wash clothes manually without using the Fuzzy Logic feature. To do so:
1. Turn the water supply on. 2. Press the (On/Off) button on the washing machine. 3. Open the door. 4. Load the articles one at a time loosely into the drum, without overfilling. 5. Close the door. 6. Put the detergent and, if necessary, softener or prewash detergent, in the appropriate compartments. 7. Press the Temperature button to select the temperature (cold water, 30C, 40C, 60C, 95C) 8. Press to rinse button to select the required number of rinse cycles. Maximum number of rinse cycles is five. The washing duration will be prolonged accordingly. 9. Press the Spin button to select the spin speed.
Note: The rinse hold program allows you to take clothes that are dripping wet out of the washing machine. : No Spin
10. Press the button repeatedly to cycle through the available delayed start options (from 4 hour to 24 hours in one hour increments). Displayed hours means the time of finished washing-cycle. 11. Press the Start/Pause button and the machine will begin the cycle.

Using Delay Start

You can set the washing machine to finish your wash automatically at a later time, choosing from 4 to 24 hour delay (in 1 hour increments). Displayed hours means the time of finished washing-cycle. To do this:
1. Manually or automatically set your washing machine for the type of clothes you are washing. 2. Press the Delay Start button repeatedly until the delay time is set. 3. Press the Start/Pause button. The Delay Start indicator will light, and the clock will begin counting down until it reaches your finish time. 4. To cancel Delay Start, press the (On/Off) button, then turn the washing machine on again.
10 SAMSUNG Washing Machine Owners Instructions

Washing tips and hints

Sorting your laundry : Sort your laundry according to the following characteristics:

Type of fabric care label symbol : Sort laundry into cottons, mixed fibers, synthetics, silks, wools and rayon. Colour : Divide whites and colours. Wash new, coloured items separately. Size: Placing items of different sizes in the same load will improve the washing action. Sensitivity: Wash delicate items separately, using the Delicate wash program for pure new wool, curtains and silk articles. Check the labels on the items you are washing or refer to the fabric care chart in the appendix.
Emptying pockets : Coins, safety pins and similar items can damage linen, the
washing machine drum, and the water tank. ribbons should be tied together.
Securing fasteners : Close zippers and fasten buttons or hooks; loose belts or
detergents, will give perfect washing results, thus saving energy, time, water and detergent. However, if your cotton is particularly dirty, use a prewash with a proteinbased detergent.
Prewashing cotton : Your new washing machine, combined with modern
Determining load capacity: Do not overload the washing machine or your laundry
may not wash properly. Use the chart below to determine the load capacity for the type of laundry you are washing. Fabric Type WF-J145N/ J125N/J105N/ J85N 7.0 kg 7.0 kg 3.0 kg 2.5 kg 2.0 kg Load Capacity WF-B145N/ B125N/ B105N/B85N 6.0 kg 6.0 kg 3.0 kg 2.5 kg 2.0 kg WFR125N/ R105N/R85N 5.2 kg 5.2 kg 2.5 kg 2.0 kg 1.5 kg WFF125N/ F105N/F85N 4.5 kg 4.5 kg 2.5 kg 2.0 kg 1.5 kg
Coloured/cotton -average/lightly soiled -heavily soiled Synthetics Delicates Wools
Detergent tips: The type of detergent you should use is based on the type of fabric
(cotton, synthetic, delicate items, wool), colour, wash temperature, degree and type of soiling. Always use "low suds" laundry soap, which is designed for automatic washing machines. Follow the detergent manufacturer's recommendations based upon the weight of the laundry, the degree of soiling, and the hardness of the water in your area. If you do not know how hard your water is, ask your water authority. Note: Keep detergents and additives in a safe, dry place out of the reach of children.
Maintaining the Washing Machine
Draining the washing machine in an emergency
WF-J145N/J125N/J105N/J85N/B145N/B125N/B105N/B85N
1. Unplug the washing machine from the
power supply. 2. Open the filter-cover by using a coin or a key.

Cleaning the water hose mesh filter
You should clean the water hose mesh filter at least one time per year, or when you see the following error message on the display:

To do this:

1. Turn off the water source to the washing machine. 2. Unscrew the hose from the back of the washing machine. 3. With a pair of pliers, gently pull out the mesh filter from the end of the hose and rinse it under water until clean. Also clean the inside and outside of the threaded connector.
4. Push the filter back into place. 5. Screw the hose back onto the washing machine. 6. Turn on the faucet and make sure the connections are watertight.
14 SAMSUNG Washing Machine Owners Instructions

Troubleshooting

Problems and solutions
The washing machine will not start
Make Make Make Make Make Make Make Make sure sure sure sure sure sure sure sure the door is firmly closed. the washing machine is plugged in. the water source faucet is turned on. to press the Start/Pause button. the the the the water source faucet is turned on. water source hose is not frozen. water intake hose is not bent. filter on the water intake hose is not clogged.
No water or insufficient water supply
Detergent remains in the detergent drawer after the wash program is complete
Make sure the washing machine is running with sufficient water pressure. Put the detergents in the inner parts of the detergent drawer(away from the outside edges). Make sure the washing machine is set on a level surface. If the surface is not level, adjust the washing machine feet to level the appliance (see page 3). Make sure that the shipping bolts are removed (see page 3). Make sure the washing machine is not touching any other object. Make sure the laundry load is balanced. Make sure the drain hose is not squashed or bent. Make sure the debris filter is not clogged The door will not open until 3 minutes after the machine stops or the power turns off.
Washing machine vibrates or is too noisy
The washing machine does not drain and/or spin

The Door does not open

Understanding error messages
Error displayed Solution Close the door. Make sure the source water faucet is turned on. Check the water pressure. Clean the debris filter. Make sure the drainage hose is installed correctly. Laundry load is unbalanced; loosen any tangled laundry. If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an "UE" error message will be shown in the display window. Call after-sales service. Before contacting After-Sales service:
1. Try to remedy the problem (See "Troubleshooting" on this page). 2. Restart the programme to see if the fault is repeated. 3. If the malfunction persists, call after-sales service and describe the problem.

Programme Chart

( user option)

Max load(kg) PROGRAM

WFJ145N/ J125N/ J105N/ J85N WFB145N/ B125N/ B105N/ B85N WFR125N/ R105N/ R85N
DETERGENT Tem AND ADDITIVES (C)

Spin Speed(MAX)rpm

WFJ125N/ B125N/ R125N/ F125N WFJ105N/ B105N/ R105N/ F105N Cycle Delay WFTime J85N/ start (min) B85N/ R85N/ F85N
WFWFF125N/ Pre- wash Sof- Max J145N/ B145N F105N/ wash tener F85N
Cotton Coloureds Synthetics Delicates Wool Handwash Quick
7.0 7.0 3.0 2.5 2.0 2.0 3.0
6.0 6.0 3.0 2.5 2.0 2.0 3.0
5.2 5.2 2.5 2.0 1.5 1.5 2.0
4.5 4.5 2.5 2.0 1.5 1.5 2.0
yes yes yes yes yes yes yes

400 400

60 1400
PROGRAM Cotton Coloureds Synthetics Delicates Wool Handwash Quick
Type of WASH Averagely or lightly soiled cottons, bed linen, table linen, underwear, towels, shirts, etc. Averagely or lightly soiled cottons, bed linen, table linen, underwear, towels, shirts, etc. Averagely or lightly soiled blouses, shirts, etc., Made of polyester (diolen, trevira), polyamide (perlon, nylon) or other similar blends. Delicate curtains, dresses, skirts, shirts and blouses. Only machine washable woolens with pure new wool label. Very light wash course like hand wash. Lightly soiled cottons or linen blouses, shirts, dark coloured terry cloth, coloured linen articles, jeans, etc.
1. Programme with prewash lasts approx.15 minutes longer. 2. The programme duration data has been measured under the conditions specified in Standard IEC 456. 3. Consumption in individual homes may differ from the values given in the table due to variations in the pressure and temperature of the water supply, the load and the type of laundry.
16 SAMSUNG Washing Machine Owners Instructions
WFJ145N/ J125N/ J105N/ J85N WFB145N/ B125N/ B105N/ B85N
WFJ105N/ B105N/ R105N/ F105N Cycle Delay WFTime J85N/ start (min) B85N/ R85N/ F85N
WFWFWFWFR125N/ F125N/ Pre- wash Sof- Max J145N/ J125N/ B145N B125N/ R105N/ F105N/ wash tener R125N/ R85N F85N F125N
Baby Cotton Heavy Soil Mixed Load Calm Wash

7.0 7.0 2.5 3.0

6.0 6.0 2.5 3.0

5.2 5.2 2.0 2.0

4.5 4.5 2.0 2.0

yes yes yes yes

800 800

No Spin

PROGRAM Baby Cotton Heavy Soil
Type of WASH Averagely or lightly soiled baby cottons, bed linen, table linen, underwear, towels, shirts, etc. Stained or heavy soiled cottons, bed linen, table linen, underwear, towels, shirts, jeans, etc. A mix of lightly soiled cottons and synthetic fabrics. Extremely low noise level during the entire cycle and finish rinse hold. Cottons, bed linen, table linen, underwear, towels, shirts.

Mixed Load Calm Wash

Appendix

Fabric care chart

Resistant material Delicate fabric Item may be washed at 95 C Item may be washed at 60 C Item may be washed at 40 C Item may be washed at 30 C Item may be hand washed Dry flat Dry clean only Can be hung to dry Can be bleached in cold water Dry on clothes hanger Do not bleach Tumble dry, normal heat Can be ironed at 200 C max Tumble dry, reduced heat Do not tumble dry Can be ironed at 100 C max Do not iron Can be dry cleaned using any solvent Dry clean with perchloride, lighter fuel, pure alcohol or R113 only Dry clean with aviation fuel, pure alcohol or R113 only Do not dry clean
Can be ironed at 150 C max

Electrical warnings

To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind: Operate the appliance only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company. Use only a grounded or polarized outlet. For your safety, this appliance is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, contact your electrician to replace your outlet. Protect the power cord. Power supply cords should be routed so that they are unlikely to be walked on or pinched by items placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.
18 SAMSUNG Washing Machine Owners Instructions
Protecting the environment
This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. Do not exceed the detergent quantities recommended in the detergent manufacturers' instructions. Use stain removal products and bleaches before the wash cycle only when strictly necessary. Save water and electricity by only washing full loads (the exact amount depends upon the program used).

7) Power-out compensation function If power is out on selected process, the process before power out is stored to EEPROM, once power is back the process before power out continues. When power is back, washing process starts from the process at the point of the power out, rinse/drain process starts from the initial process. POWER-OUT COMPENSATION FUNCTION PROCESS

WASHING

RINSE/DRAIN START

RINSE/DRAIN PROCESS

FINISH
POWER OUT SAVE DATA to EEPROM SAVE DATA to EEPROM POWER BACK

POWER OUT

POWER BACK

MICOM RESTORE

8) Fuzzy washing function (weight-sensing) After nishing initial water supply, when the fall of the water level needs supplementary water supply, Sensing function perceives the weight with the supplementary water supply numbers and starts to work. Under the course of Cotton, or Coloureds, if the supplementary water supply numbers become over 2 times the function is going at default condition ( high water level ), if 1 time that is going at middle level, if 0 below low water level, heating hours and rinse hours depend on the above data. ECO PRE mode is selected, the process going on at default condition. Washing hours Cotton High Middle Low Default Default-20 min Default-30 min Coloureds Default Default-10min Default-15min Rinse water level Default 23.80KHZ 24.10KHZ
After sensing weight, above hours is decreased from above default hours 9) Bubble - detecting function At the each condition of washing&dehydrating , rinse&dehydrating , hydrating, bubble -detecting function works, this function works 5times normally, if the function detects bubbles at 6 times , the bubble-detecting function stops and go on to the next process. The bubble-detecting function during washing & dehydrating to rinse & dehydrating after 2 times instant dehydrating and before main dehydrating, if the water level is under 24.50KHZ, Bubble Detecting function thinks there are bubbles and add the bubbles-removing rinse, needing hours are above hours and 8 Min 40 sec. The bubble-detecting function during single hydrating process after 2 times instant dehydrating and before main dehydrating , if the water level is 24.50KHZ below or during main dehydrating, water level data is 24.50KHZ below Bubble-detecting function thinks there are bubbles and add the bubbles-removing rinse 1 times, needing hours are above hours and 5 min 50 sec.

Bubble-detecting function operating process

500rpm

220rpm
18 sec laundry scattering
draining &reverse 50 sec
unbalance detecting range
bubble detection (default water level 24.50KHZ below)
10) Unbalance detecting & laundry balance positioning system Just before the hydrating process and just after reversal rotation for balancing laundry position, this function is carried out The initial 6 sec is the period of reversal rotation for balancing laundry position , Drum rotates 50rpm for initial 6 sec Next 12 sec, the rotation increases the speed from 50 rpm to 95 rpm slowly During the next 8 sec, drum rotates at the speed of 95 rpm, the sensor decides the degree of laundry unbalance with TACHO data which is attached to motor If the degree of unbalanced laundry is over 6 times to default value, laundry balancing system carryies out feed back process 3 times.
Unbalance detecting & laundry balance positioning system

490rpm 500rpm

210rpm 220rpm
20 sec laundry scattering
11) R.P.M control The rotating motor enables the magnetics( i.e generator) to generate magnetic ux in proportion to r.p.m, magnetic ux induced by coil sensor in the opposite side produces the wave like the gure below to d/dt and via rectangular wave generating circuit, the waves reaches MICOM and micom controls r.p.m with the pulse, count and cycle inputted by program.
<COIL electrical wave at both ends>

V (VOLT)

T (HOUR)

3-4. TECHNICAL POINT

1) Motor on/off time at each course

unit:sec

Model Course Cotton Coloureds Synthetics Wool Handwash Quick Pre Cw 10 Off 10

Washing Ccw 10 Off 10

Motor r.p.m 50
2) Final dehydrating r.p.m at each course

unit:rpm

Model Course Cotton Coloureds Synthetics Wool Quick Handwash

WF-R400

You can change the r.p.m to the above a table by use spin button under no spin situation.
3) The water supply control at each process cycle
Model Process cycle Pre Washing Washing Rinse Final rinse Cold water 5L/min Cold water 10L/min + (Hot water 10L/min) Cold water 10L/min Cold water 10L/min + Cold water 5L/min WF-R1061,WF-R861

This wash machine is equipped with 2 Shock absorbers with same capacity and with 2 buffer springs. 2 Shock absorber are placed under the tub and outside case , 2 buffer springs are placed on the right and left of the upper side of outside case. Shock absorber function: during wash, dehydration absorb the shock. buffer spring: buffering the vibration

device Shock absorber

capacity of Shock absorber 82 kg
4-1. GENERAL ERROR FUNCTION
1. An occurrence of an Error will make a sound of error melody for 5sec and continuously show one of the Error Displays from the following errors. (But, Fault Check Led will ash for 0.5sec.) All of the steering parts will be off at that time until that error was released. Water Supply Error - If there is no higher change in water frequency than 100Hz for 2 minutes during the initial time of water supply and if water level doesnt reach the preset level in 10 minutes, this error will occur. This error will be released using Start/Pause button, which performs the initial condition of operation. - Display : 4E Water Drain Error - If water level frequency is still lower than the reset level frequency (25.20kHz) in 10 minutes after starting of water drain, this error will occur. This error will be released using Start/Pause button, which performs the initial condition of operation. - Display : 5E Over Flow Error - If an abnormal water level frequency is sensed (for occurrence of Over Flow :21.00kHz), Auto Power Off may release this error and continuously progress water drain until the frequency reached 25.00kHz. - If Over Flow is also sensed even after the following check of water level frequency indicating that error, it functions to progress water drain. - Display : OE Door Open Error - This error will be released by closing Door. - Display : dE Unbalance Error - This error will be released by pressing start/pause S/W. - DISPLAY : UE Water Heater Error - This error will be released by turning off Power S/W. - Display : HE1(Over Heat), - Display : HE2, indicating no operation of HE. Pressure S/W (Single Part Trouble) Error Frequency signals(kHz) generated by water level S/W Water Level Abnormal Frequency Low 30.00 KHz High 15.00 KHz
- If the above frequency signals are displayed longer than 5sec, it indicates Pressure S/W Error. - Drain water for 3 minutes for that Error, and turn OFF water drain pump. Pressure S/W Error display IE will be shown. 10. Abnormal Water Temperature ERROR - Water drain begins if abnormal water temperature is sensed at the initial time of water supply. If the frequency higher than 25.20KHz is sensed, water will be drained by force. - Display : CE - This error will be released by turning off Power S/W.
11. Natural Drain/Water Leak Error - If more than 4 times of water supply and safe water level of Heater are sensed for each course, this error will occur. - Display : LE - This error will be released by turning off Power S/W. 12. Tacho Error - If Motor Tacho is abnormal, this error will occur. - If Tacho signals are inputted less than 2 for 2sec after Motor started, this error will occur. - Display : 3E - This error will be released by turning off Power S/W. 13. Motor TRIAC Short Error - If Tacho signals are inputted more than 300 every 1sec in the operational interval less than 90RPM, this error will occur. Turn off Power S/W at that time. - Display : bE - This error will be released by turning off Power S/W. 14. Thermistor Abnormal Error - If Thermistor circuit is abnormal, this error will occur. - If Thermistor is lower than 0.2V or higher than 4.5V, this error will occur. - Display :tE - This error will be released by turning off Power S/W.

Remove the motor.
Remove the xing screws for the water supply valve.

Water Supply Valve

Disconnect the valve wires. Separate the water hoses.

Water Level Sensor

Remove the top cover.
Remove the xing screws for the water level sensor. Disconnect the water level sensor harness. Disconnect the hose pressure. Replace the water level sensor.
Remove the xing screws holding the Door-Glass. Separate the glass.

DoorHinge

After removing the two screws holding the Holder Glass, replace the Door Hinge. After putting them back together, check if the screws holding the Door Hinge is fastened properly.

Drain Pump

Insert the at head screwdriver into the slot on the top of the Cover Filter and lever it down to separate it.
Unscrew the drain lter by turning it counter clockwise. - The water remaining inside could ow out. So, put an empty bowl on the oor to hold the water.
Tilt the unit backward and take out the drain pump.
Disconnect the incoming water hose and the wire harness. (Caution: Check if the unit is plugged out. There is possibility of electric shock.)
Separate the Hose Filter Tub and the Drain Hose.
CHECK POINT 1. Remove the Drain Filter and check if there are foreign substances (coin, buttons, etc) blocking inside - If so, clear the inside. 2. Check if the wire harness is connected properly - If not, connect it properly. 3. If water leaks, check if the Clamp Hose and the Cap Drain are assembled tightly - If not, assemble them tightly. Remove the water remaining inside by turning the Filter counter clockwise.

Open the Door.

Door S/W
Remove the Spring Diaphragm and separate the Diaphragm from the Frame Front. - Insert the at head screwdriver and pry up the spring to remove the Spring Diaphragm. - The Diaphragm could get damaged when taking it out. So, unseat it in one direction slowly.
Remove the screws holding the Door S/W. Take out the Door S/W. Disconnect the wire connector. (Press the hook to unlock the tab and plug it out.)

Heater

Remove the frame-front.

HowTo Do

Disconnect the Connector Housing.
Remove the nut holding the Heater and

separate the Heater.

Take out the Heater from the Tub.
( Caution: Be sure to insert the Heater into the Bracket in the Tub. If not, it may cause a fire. And, make sure to have the Packing seating on its place. Fasten the nut with 5Kgf/. If the nut is fastened loosely, it may cause water leakage.)

6. TROUBLE DIAGNOSIS

6-1. TROUBLE DIAGNOSIS
As the micom wash machine is congured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide.

The water is not supplied.
The wash does not start though the water supply is stopped.
The drum does not rotate during washing. 4
The drum rotates by one direction during washing. (The drum rotates to one direction for SPIN.) Drainage problem.
Dehydration problem. Abnormal noise during SPIN.
Leak breaker or current/leak breaker is down during washing. 9
6-2. PROBLEM CHECKING AND METHOD OF PCB
6-2-1. The Part Of Power Source

NO Power On YES

The Voltage Of Between e and f Is As Big As DC300V? YES The Voltage Of Between a and b is as big as DC 12V? NO Check LVT1 And IC3 NO Check The DIODE(D18~D21)
YES The Voltage Of Between d and b is as big as DC5V YES NO Exchange IC4(7805)And Check The condenser(CE4)

ok e a c d

6-2-2. Reset Part
The Value Of Measurement Result Of Between Micom 8And Gnd Is 5V? NO Check The Power Source

YES Check IC7

Check The Curve Output Of ?

Check PC2

6-2-3. Interrupt Part
Y Check The Micom Number 9? N Check TR2,R32
Y Check The Part Of Oscillator
6-2-4. Checking The Part Of An Oscillator
When The Micom 2,3 Check, The Value Is 16Mhz? YES Exchange Micom NO Check Resonator R46
6-2-5. Check The Part Of Buzzer

Part Confirm DC12V ?

Check The Part Of Power Source
YES Exchange BZ1, Check TR1,R59, Micom 47
6-2-6. Driving Part Checking
Conrm The Output Of DC5V, When The Every Part Of Micom Number Check, According To The Some Problem Condition ex) When The Drain Is Not Operating But Pump Motor Is Operating, Check The 5Voltage Of Micom
Micom Number 31 Is 5 Voltage?

Micom Bad

The Part Of aIs 0 Voltage?

Check The IC6 KID65003AP

Check R47, TRIAC4
Check The Micom 18th In The Above Method When The Cold Water Is Bad
6-2-7. Conrm The Driving Part Of Motor

Motor Is Not Spinning

Check BD1, TRIAC1
Motor Is Not Turning Right And Left

Check RELAY3

NO Check The Tacho Part
6-2-8. Checking The Tacho Part
Have The Motor Turn In Hand
Is The Rectangular Curve In The Micom 13?
Check The Surroundings Circuit And TR5

Exchange The Motor

6-3. DETAILED DIAGNOSIS
1. Driving Compartment Test Mode A. Hold down the and the buttons simultaneously and then press the Power button. (All of the LEDs li ght up and the display shows t1 in 3 seconds.) B. The driving part can be tested when you press the push button dial right after entering into the TEST MODE. No Check Test Method Check if the motor operates or check the Motor terminals. Description Motor Wiring (Red/White /Blue/Pink/ Violet/White ) Resistance between Blue-Red, Red-White and White -Blue should be 2.010%. Check resistance of the Water Valve terminals. Check resistance of the Drain Pump terminals. Check resistance of the Door S/W terminals. Check frequency (Hz) between the Water Pressure Sensor terminals.

Part Number

Description

Display

Displays or indicates operations or functions

Power_key

Turns the power on/off

Start_key

Stars/stops an option
Selects and processes each function

Connect to the GND Wire

Detects if the door is open or closed

Connect to the AC1 Wire

9-2. Connector & Relay Terminals Description (MAIN PCB)

10-1. EMZ (WF-F1061)

A LVT1 +12V +8V 4.7K IC1 R3 SV50-R32 A LED1 LED2 LED3 LED4 RLED7 LED8 LED5 LED6 SV50-R32 RLED9 LED10 LED11 LED12
12 ISP_TX ISP_RX ISP_TEST 51 MOTOR_CONTROL AG-IH 58 57

SCHEMATIC DIAGRAM

D25 UG2D C4 CE2 +5V IC4 IN KA7805A

4.7k CHIP X 7

D20 D21

1N4007

L N AC220-240V AC100-120V D24 D23 UF4007 C7 CE4 470uF

CN4 GND C23 330

ZNR4 20D561 CE3 470uF 100nF 100nF +5V

AVDD 63 VAREF VDD

CM2 100nF

PTC1 IC3

270M TNY266P

BYP S3

FILTER T-PJT I1 O1 I2 O2 I3 O3 I4 O4 I5 O5 I6 O6 I7 O7 VCC GND

L1 UG2D OUT

CE1 10uF C2 2.2nF

R24 100K

MICOM1 TMP86FS49FG

R25 C3 100

PC1 R26 100
VSS DIGIT-LED 7 THERMISTOR_HS 23
R2 R4 R7 R8 R10 R13 R9 KID65003AP

B 100nF ZD1

+5V SMW250-06DW

LTV817B

MTZJ11B R50
RELAY2 HEATER_RELAY RLED13 LED14 LED15 LED16 R11

IN GND OUT

DOOR SWITCH R18 100K PC2 C3 TR2
+12V R31 4.7K R32 1K 330 LED17 LED18 LED19 R12 330

DGND DGND

THERMAL CUT OFF 10nF LTV814 R29 47K C22 100nF 1uF 4.7K 100nF MMBT1K CE6 R45 C25 R30 IC7 CN7 10K R53

SET GND R20 100K

GRN ZNR1

DSP1 CSD-4328G B

CN1 14D911D14D182

RELAY1 POWER_RELAY LED20

13 TACHO

+12V C28 R14 330

DOOR-SIG IN 42 POWER_RELAY DIGIT-LED CW/CCW 36

LED21 LED24

C 10nF

ZERO CROSS

BLK YDW236-01BLK

OMIF-S-112LM

11-1. PCB CIRCUIT DIAGRAM

HEATER_RELAY

CC1 680nF C11 10nF C26
SCAN-LED KEY SCAN-LED KEY

POWER_RELAY F1

LED22 LED23 LED25

SCAN-LED KEY

POWER_RELAY

GRN TR6

16 SCAN-LED KEY SCAN-LED KEY SCAN-LED KEY DIGIT-LED DIGIT-LED DIGIT-LED DIGIT-LED DIGIT-LED 62 DIGIT-LED DIGIT-LED 27
OMIF-S-112LM 10nF 150 TRIAC2 TRIAC_1A IC6
THERMISTOR_HS PWM_AG SCAN-LED KEY 27 HIGH_SPEED SCAN-LED KEY P50 THERMISTOR_H 22

3 THERMISTOR_H

THERMISTOR_HS

C8 100nF

HEATSINK TERMISTOR R43 4.7K

CN9 CE5 10uF 100nF

R56 C18

CE8 10uF

CIS-MID NEW

[SMPS, FLASH MICOM]

MFG ENGR CHK Changed by Date Changed Saturday, August 15, Time Changed

16:30:00 P.M.

QA CHK 7

Drawing Number 8

12-1.OVERALL SYSTEM
Function Generates a required DC power of 12V or 5V in case of supplied or disconnected AC power. Description - When AC 220V is applied to D18~D21 it to DC 300V - When DC 300V IS appliedto IC3 LVT1t to dC 12V. and dc 8v - The 8v is transformed to DC 5V through IC4(KA7805).
12-2.AC INPUT & POWER CIRCUIT
Function Controls each driving system (VALVE, DOOR S/W, DRAIN-MOTOR) by turning RELAY or TRIAC on/off. Description - MICOM outputs a high signal of 5V from pin # 29,30,31,32,34 of micom. - Then, IC6 grounded (0V). pin10~16 areelectrically
12-3.DRIVING SYSTEM CIRCUIT
- When pin # 10 to 16 are grounded, and the TR14,15 are grounded this creates an electric potential difference from the 12V that turns on RELAY 1,2,3,4 and TRIAC1,2,3,4,5,6 - The operating parts (VALVE, DRAIN-MOTOR, DOOR S/W) connected to CN6 turn on if they are supplied with power.

12-4.MOTOR CIRCUIT

Function Supplies power to the motor and turns it CW/CCW (Right / Reverse direction). Description
- The operation of TRIAC1 is the same as that of the driving system. - If the electric potential of R39 is grounded (0V), TRIAC1 turns on. - CN1 detects if the door is locked or unlocked. If unlocked, it does not apply power to the motor even if TRIAC1 turns on. - If the door is unlocked and TRIAC1 turns on, the motor connected to CN4 is supplied with power and drives CW (right direction). - Under such conditions, turning RELAY3 on will drive the motor CCW (reverse) as the wiring is switched to CCW. - Turning RELAY4 on will switch the winding of the motor to one for higher driving
Function Detects signals from the sensor and controls the current system. Description
12-5.SENSOR DETECTION CIRCUIT
- The water level sensor is connected to pin 8 of CN6. - The frequency of the level sensor changes according to the water amount in the tub. - Then, the frequency is input to MICOM pin 48 for detecting the water amount. - The DHSEH sensor is connected to CN9 ; - The resistance of the temp. sensor changes according to the ambient temperature. The changed resistance is applied to R56 and R57. - The voltage applied to R56 and R57 is decided according the temp. MICOM stores the value. - When voltage is applied to MICOM pins 23, MICOM compares it to the predefined one before detecting the current temp.

Management Door is not opened during washing. For models applied with the boiling or drying the door will not open until the interior temperature decreases to a certain safe level. In other cases you are recommended our engineers inspection. Is it the label for advertisement? Is it the label for standards or attentions? If it is for advertisement it does not matter for the function or the use even though it is not attached since it is not related to the function and use. If it is for st

appear ance part

Label(sticker) being detached

consulting

for the specica tion or label of product lead the customer to attach diretly or send the engineer to do so. For other advertise ment or PR label it may not be at tached.Check whether the componets are same as those in the manual. If not contact to SVC. It may be oc curred when the machine is installed in the humid place which causes the rust or dis coloring. It is a symptom occurred when it is in stalled in the humid place or the water is entered its inside.
DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*)
Accessories being not included

AS rere commended

Sir we really apologize to you for the inconvenience that we made from our product which was bought by you on the basis of your trust in us. We will try our best to clear your inconvenience (by mail). Being rust or being discolored during the use is normal and natural according to the times and its use.(except the case occurred at the innitial purchase). The replacement of case will be charged and in order to prevent the corrosion change the location

Color coming off/rust

DRUM WASHER (MODEL NAME : Q1*3*)

display part

Display part being not lit up/ not being cleared
Dry the front operation part a little with the drier and you are recommended our engineers inspection if it does not work even after doing so.
DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*)
Character being broken on display

AS rere commen ded

In this case you are recommended our engineers inspection.

Display not being cleared

Display malfunction

door re lated
Door sensor not being detected

Others

a noise
A noise being occurred intermittently during washing

General consulting

Please check whether a washer is installed and used with removing the safety device posi tioned at its rear.
You are recommended our engineers inspection if the safety device is removed and there is no foreign material such a coin or pin inside.
A noise being occurred intermittently during dehydrating
.Make a comment for the customer to prepare the memorandum since he can not be famaliar with the contents comple tely.
Did you remove the washer safety device? It may be occurred when the laundry is leaned to one direction or the machine is not aligned horizontally or the foreign material is entered. It may be occurred when the laundry is leaned to one direction or the machine is not aligned horizontally or the foreign material is entered.
Please check whether the machine-installed place is not leaned to one direction and then level it and then check whetehr there is no foreign material inside such a the coin or pin. If the noise occurs without any problem in the machine a check is requir
A noise to touch other parts
Check whether the machine-installed place is not leaned to one direction and then align it horizontally and then check whetehr there is no foreign material inside such as the coin or pin. If the noise occurs without any problem in the machine. Inspectio

A noise of Motor

Noise during water darainage -roaring sound
You are rerecommended our engineers inspection because there may be a problem on the components.
A noise being occurred during water supply
The foreign material may be inserted inside the water supply hose or the pressure of water may be too high or too weak. Lead to re assembe when water supply hose is departed. It may be used with so much de tergent or left alone for a long time without use. It is a symtom occurred when the hose of bot tom not outside is departed or torn off. It may be occurred when it is pushed out due to the water pres sure or it has bad connection. The leakage during water supply can occur possibly due to the bad connection of tap and coupler and water supply hose.

For the machine having the drain hose at the below of that raise the drain hose up and x it to the xer at 2/3 point of the machine. If the hose is used at the oor all water supplied will drain fully.

smell/ smoke

Burning smell
Is that a newly bought one? A smell is disappeared after 4~5 days passed in case of newly bought one but it depends upon the frequency of use. Be sure to use it without worry. If is not disappeared contact a engineer

Burning/smoke

power soruce related

Power not supplied

AS rerecom mended
Take out the power cord and put it in again and check whether the power for the other products is on. If it is not even after that you are recommended our engineers inspection.
DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*)
Current leakage breaker being dropped
Autmatic stop during operation

AS rerecomm ended

Reduce the contents to be washed. If it continues you are recommended our engineers inspection.
Being power off frequently

operation related

Button being not operated

Consulting

Being not rotating during washing
First check whether the tap is open and the cover closed and then request an engineers inspection.
4E :front loading washing machine error
Water level sensor inferiority
This may be happened when there is any foreign material inside the water supply and drain valve or the interior components of the prodcuts do not operate normally. Water level sensor or mother rotation. It may be occurred when the drain hose is go over the threshold or water is not drained. It may eb occurred when the The lter of pump-drain moder is fulled with dregs, It may be a case that the supply water level is not detected. It may be happened when the oor of the installed palce is not at or the clothes are entangled. It may happen when the boiling temperatuer rised rapidly. (It is also because too much detergent are used.) It may appear when it dose not reach to the set temperature within a certain time. It may happen when there is a trouble in air hose or water level sensor. Check whether the hose for hot and cold water is connected to the water supply hole. Check whether there is foreign material inserted in the drain lter. Check whether there is foreign material inserted in the drain lter.

Disconnect the water supply hose and check whether there is a foreign material inserted in it. And then request an engineers inspection.
5E :front loading washing machine error

Water being not drained

AS rerecommended
Check the installation of drain hose and then if there is no trouble request an engineers inspection. Clean the lter of pump-drain motor. Guided by instruction-manual.
OE :front loading washing machine error UE :front loading washing machine error

3E OVER-FLOW

After Draining the water power off and on and operate again. If it dose not work after so doing request an engineers inspection.

4E UNBALANCE ERR

Level the machine or arrange the entangled clothes. If it does not worked even after so doing request an engineers inspection.
HE1 : front loading washing machine error

E5 WATER HEATER ERR

Use the proper amount of detergent and power off the machine till the temperaure is cooled down. And if it does not work even after so doing request an engineers inspection.
DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*) DRUM WASHER (MODEL NAME : Q1*3*)
HE : front loading washing machine error 1E :front loading washing machine error cE : front loading washing machine error

E6 WATER HEATER ERR

E7 Water level sensor ERR
E8 Abnormal water temperature ERR
Check whether the cold water is supplied through the cold water supply hole and if it doesnt work after so doing request an engineers inspection.
8E : front loading washing machine error tE :front loading washing machine error

E9 Water leakage ERR

11E : front loading washing machine error door : front loading washing machine error
Check whether there is foreign material inserted in the drain lter. It may appear when the the door is opened a certain minutes after the completion of washing or the electricity is interrupted in running. Check of Bad contact of 1st door opening sensor---*check of the bending of 2nd door switch*Do not open the door

Ed:Door being not opened

There is a cover dettachable at the front bottom. Pull out the cover to nd the handle to open at the right side. Pull out the handle to open the door.
front loading washing machine error water supply related

E6:Overheating error

It may appear when the temperarture rises rapidly.
Cold water being not supplied
Check rst whether the water supply is cut and also check whether the foreign material is inserted. If the foreign material is inserted turn the connection hose of machine to the left to disconnect and to nd the strainer to trap the foreign material. It may appear when the tap is not opened properly or there is a foreign material inside. It may appear when the longterm used detergent is not well soluted or when the water temperature is low during winter. It may appear when the water is cut or the water supply hole is clogged. Is it checked whether the tap is fully open or there is a foreign material inserted? First check whether the tap is fully open. And there is no fault turn the hose of the machine to the left to take out strainer in the hole of water entrance. Clean i Sove the detergent wth the hot water and put it inot the washing box. If it is not solved even with the normal detergent request an engineers inspection.

water supply related

Water being supplied little

Detergent being remained

Water being stopped during the coming in
Is it checked whether the water is cut or there is a foreign material inserted in the water supply hole? First check whether the water is cut and if there is a blackout push the power button on. Otherwise turn the machine hose to the left to take out t In this case you are recommended our engineers inspection.

Clothes being damaged

One direction rotation
Rotation being not worked after it sounds with buzz
Water being not supplied in winter
It may appear when the tap and the water supply hose are frozen if it is used at the veranda in the winter.
Make the water supply hole warm and defreeze it with wet towel.

rinsing related

Rinse being not put in tub
It may appear when the rinse agent remains to clog.
Did the rinse agent drain immediately or part to put the rinse is clogged after putting the rinse agent? The rinse agent does not drain only when putting it up to the reamer shaped cap which is in the box of rinse agent. If clogged take out the cap and If there is too much laundry or vinyl clothes the detergent is not solved. Reduce the laundry or take out the vinyl clothes separately.

Bubble being remained

It may appear when there is too much or too little laundry.

water drain related

dehydrating related
Dehydrating time being increased again
.Make a comment for the customer to prepare the memorandum since he can not be famaliar with the contents completely.
The vibration and noise occur when the horizon is broken or the laundry are leaned to one direction. So It may appear when the safety device is operating to prevent it. If the washing machine consumes hours more than necessary check whether the water supply is too small. And note that that the boling and the drying course takes much time. The power cord for motor may be cut or the gear shaft hardened.

If there is too little laundry less than 1KG or the clothes in the washing tub are severely entangled it appears.
Washer being worked for four hours without stopping

Specic consulting

Check whether the water supply time is too much delayed due to the low pressure of water or boiling or drying is selected. In other cases request an engineers inspection.
Not dehydrating with the motor being purring after water is drained
Being stopped with thuds during dehydration
It may appear when the horizon is broken or there are too much clothes to wash. It may appear when there are clothes like vinyl.
check the level of a washing machine.

Not being squeezed well

Check whether the vinyl clothes are attached on to the washing tub so as to prevent the immediate the outgoing of the moisture to the outside. Otherwise request an engineers inspection. There may be remaining water since the products is delivered thorugh the nal products test. It is normal and you can use it without fear.
Water being in at purchasing
Dehydration being not worked at all
It may appear when the interior components do not work properly. It may appear when the machine is used at the outside or the veranda.the drainage hose clogged or foreign material inside

others

Action for water being freezen in winter
pour the warm water on to the tap to take out the water suppy hose and put the hose in to the water of approximately 50 degree. And then pour the water in to the washing box to check whether the drain is well done. After loosening the water supply hose and check the inlet of water supply whether there is foreign material inserted such a soil dust.
being clogged/foreign materials
installation / connection
Consulting for installation of front loading washing machine
The drum washing machine is leveled after removing the safety device at the rear of drum. And for a removing the safety device refer to accessories and users manual. Level it by use of a leveller(with a coin weight) at the front.

Level check

Removal/house moving reinstallation
It is possible to remove and install in the house but when moving to the other house and installing it assemble the safety device at the back while moving and remove it after moving. If the drum is shaken during the moving it causes a serious damage. It may appear when there is too much laundry. Check whether there is foreign material inside (coin nail and other sharp material) and so it may appear due to the zipper or button of jeans. Check whether the laundry is input over the proper amount. Otherwise request an engineers inspection.