WORLD HEADQUARTERS Chicago, Illinois U.S.A. SRAM Corporation 1333 North Kingsbury, 4th floor Chicago, Illinois 60622
ASIAN HEADQUARTERS Taichung, Taiwan SRAM Taiwan No. 1598-8 Chung Shan Road Shen Kang Hsiang, Taichung County 429 Taiwan R.O.C.
EUROPEAN HEADQUARTERS Amersfoort, The Netherlands SRAM Europe Basicweg 12-D 3821 BR Amersfoort The Netherlands

5 mm 5 Nm 44 in.lbs.

ANATOMY

USE CAUTION

Always check the front and rear brake levers for proper operation. If there is interference between a shifter and a brake lever, rotate one out of the way. Check for proper brake lever operation again!

COMPATIBILITY

X.9 / X.7 rear shifters:

INSTALLATION

Rear derailleurs SRAM ESP Rear Derailleurs X.0 / X.9 / X.7 / 5.0 / 4.0 / 3.0 (1:1 Actuation Ratio)

CABLE CHANGE ADVICE

Leave the shifter on the handlebar. The shifter does not need to be opened. Use only new, high quality cable and compressionless cable housing.
Make sure the shifter is in gear position 1 (front shifter) and 9 (rear shifter). Detach the cable from the derailleur. Cut the cable off 6" (15 cm) from the shifter barrel adjuster. Discard the old cable and cable housing.

Operating instructions

CAUTION
Read all instructions for correct installation and use.

brake lever

Slide first shifter then brake lever onto handlebar. Bar end users dont forget to leave room for the bar end.
Trigger Shifters X.9 X.7 Rocket Attack

handlebar grip

Slide the handlebar grip onto the handlebar.
Never use lubricants or solvents to install handlebar grips. Handlebar grips provide an axial safety function. For this reason, they should be mounted in such a way as to make sure they do not slip off handlebar.
Rocket / Attack rear shifters:
Rear derailleurs Shimano (2:1 Actuation Ratio)

MAINTENANCE

shifter barrel adjuster
Tighten the 5 mm hex clamp bolt to 44 in.lbs. (5 Nm).

ADVICE

Clean the shifter using only water and mild soap.
This shifters are nearly maintenance free. For any questions regarding methods of disassembly or maintenance, please contact your qualified local dealer.
X.9 / X.7 / Rocket / Attack front shifters:
Front derailleurs SRAM & Shimano
Feed the cable through the cable housing and stops. Make sure the shifter is in gear position 1 (front shifter) and 9 (rear shifter). Attach the front/rear shifter cable to the front/rear derailleur. Adjust indexing per derailleur instructions.
Carefully unscrew cable change cap from cable entry with a screwdriver. Push cable out of the cable entry with rotating movement. Feed the new cable through the cable entry and out the barrel adjuster. It may be helpful to remove the barrel adjuster for better visibility.
Released 1/2003 Publ. No. 4208 www.sram.com
Replace cable change cap. Feed the cable through the new cable housing and cable stops. Attach the cable to the derailleur and adjust indexing per derailleur instructions.

EINZELTEILE

GEBRAUCH ACHTUNG
Bevor Sie losfahren, versichern Sie sich immer, dass die Bremsen einwandfrei funktionieren. Falls sich Bremshebel und Schalter gegenseitig beeintrchtigen, drehen Sie einen der beiden in eine andere Position. berprfen Sie die Funktion der Bremsen noch einmal!

WORLDHEADQUARTERS Chicago, Illinois U.S.A. SRAMCorporation 1333 North Kingsbury, 4th floor Chicago, Illinois 60622
ASIANHEADQUARTERS Taichung, Taiwan SRAMTaiwan No. 1598-8 Chung Shan Road Shen Kang Hsiang, Taichung County 429 Taiwan
EUROPEAN HEADQUARTERS Amersfoort, The Netherlands SRAMEurope Basicweg 12-D 3821 BR Amersfoort The Netherlands

5 mm 5 Nm 44 in-lbs

p/n 95-7015-005-000 Rev A SRAM Corporation, 2007 www.sram.com

anatomy

maintenance
Advice Clean the shifter using only water and mild soap. These shifters are nearly maintenance free. For any questions regarding methods of disassembly or maintenance, please contact your qualified local dealer.

installation

Either component can be mounted first, depending on your ergonomic needs. Slide the handlebar grip onto the handlebar. Cau t i o n Never use lubricants or solvents to install handlebar grips. Handlebar grips provide an axial safety function. For this reason, they should be mounted in such a way as to make sure they do not slip off the handlebar.

c ab l e c h a n g e

Advice Leave the shifter on the handlebar. The shifter does not need to be opened. Use only new, high quality cable and compressionless cable housing with end caps. Line-up the shifter in gear position 1 (front shifter) or the highest gear number (rear shifter). Detach the cable from the derailleur. Cut the cable off 6" (15 cm) from the shifter barrel adjuster. Discard the old cable and cable housing.
sra m c o r p o ra t i o n w arra n t y
Extent of Limited Warranty SRAM warrants its products to be free from defects in materials or workmanship for a period of two years after original purchase. This warranty only applies to the original owner and is not transferable. Claims under this warranty must be made through the retailer where the bicycle or the SRAM component was purchased. Original proof of purchase is required. Local law This warranty statement gives the customer specific legal rights. The customer may also have other rights which vary from state to state (USA), from province to province (Canada), and from country to country elsewhere in the world. To the extent that this warranty statement is inconsistent with the local law, this warranty shall be deemed modified to be consistent with such law, under such local law, certain disclaimers and limitations of this warranty statement may apply to the customer. For example, some states in the United States of America, as well as some governments outside of the United States (including provinces in Canada) may: a. Preclude the disclaimers and limitations of this warranty statement from limiting the statutory rights of the consumer (e.g. United Kingdom). b. Otherwise restrict the ability of a manufacturer to enforce such disclaimers or limitations. Limitations of Liability To the extent allowed by local law, except for the obligations specifically set forth in this warranty statement, In no event shall SRAM or its third-party suppliers be liable for direct, indirect, special, incidental, or consequential damages. Limitations of Warranty This warranty does not apply to products that have been incorrectly installed and/or adjusted according to the respective SRAM technical installation manual. The SRAM installation manuals can be found online at www.sram.com, www.rockshox.com or www.avidbike.com. This warranty does not apply when the product has been modified. This warranty does not apply when the serial number or production code has been deliberately altered, defaced or removed. This warranty does not apply to damage to the product caused by a crash, impact, abuse of the product, non-compliance with manufacturers specifications of usage or any other circumstances in which the product has been subjected to forces or loads beyond its design. This warranty does not apply to normal wear and tear. Wear and tear parts are subject to damage as a result of normal use, failure to service according to SRAM recommendations and/or riding or installation in conditions or applications other than recommended. Wear and tear parts are identified as: Dust seals/Bushings/Air sealing o-rings/Glide rings/Rubber moving parts/Foam rings/Rear shock mounting hardware and main seals/Stripped threads and bolts (aluminum,titanium, magnesium or steel)/Upper tubes (stanchions)/Brake sleeves/ Brake pads/Chains/Sprockets/Cassettes/Shifter and brake cables (inner and outer)/Handlebar grips/Shifter grips/Jockey wheels/Disc brake rotors/Tools This warranty shall not cover damages caused by the use of parts of different manufacturers. This warranty shall not cover damages caused by the use of parts that are not compatible, suitable and/or authorized by SRAM for use with SRAM components. This warranty shall not cover damages resulting from commercial (rental) use.