POWERMAX PRO
Fully Supervised Wireless Alarm Control System

Installer Guide

4.4.22 Back Light.. 16 4.4.23 Duress... 16 4.4.24 Piezo Siren... 16 4.4.25 Reset Option... 16 4.4.26 Tamper Option... 16 4.4.27 Siren On Line.. 16 4.4.28 Memory Prompt.. 16 4.4.29 Disarm Option.. 16 4.4.30 Bell/Rep. Option... 16 4.4.31 Low-Bat Ack.. 17 4.4.32 Screen Saver.. 17 4.4.33 Confirm Alarm.. 17 4.4.34 AC FAIL REP.. 17 4.4.35 Code Version.. 17 4.4.36 User Permission... 17 4.4.39 Key Zones Options (Optional).. 17

TABLE OF CONTENTS

1. INTRODUCTION.. 3 2. SPECIFICATIONS... 3
2.1 General Data...3 2.2 RF Section..4 2.3 Electrical Data..4 2.4 Communication..4 2.5 Physical Properties..4

3. INSTALLATION.. 4

3.1 Unpacking the Equipment..4 3.2 Supplying Power to the Unit...4 3.3 System Planning & Programming..4 3.4 Mounting...4 3.5 Back Unit Mounting and Wiring..4 3.5.1 Phone Wiring..5 3.5.2 Zones and Sirens Wiring..6 3.5.3 Installing an Optional X-10 Siren..6 3.5.4 Dual RS-232 Module Mounting..7 3.5.5 Audio Module Mounting..7 3.5.6 Power Cable Connection..7 3.6 Front Unit Preparation..8 3.6.1 Backup Battery Insertion..8 3.6.2 X-10 Interface Module Connection..8 3.6.3 Optional GSM/GPRS Module Mounting..8 3.7 Final Closure...9
4.5 DEFINING COMMUNICATION PARAMETERS. 19
Preliminary Guidance.. 19 4.5.1 PSTN / GSM (Fig. 4.5 Detail A).. 19 4.5.2 GPRS / BB (Fig. 4.5 Detail B).. 19 4.5.3 C.S. Reporting (Fig. 4.5 Detail C).. 20 4.5.4 Private Report (Fig. 4.5 Detail D).. 21

4. PROGRAMMING... 10

4.1 INTRODUCTION..10 4.1.1 General Guidance...10 4.1.2 Entering an Invalid Installer Code..10 4.1.3 Installers Menu..10 4.1.4 Setting a New Installer Code..10 4.1.5 Setting a New Installer Code in PowerMax Pro that has 2 Installer Codes..10 4.2 ENROLLING WIRELESS SENSORS AND KEYFOB TRANSMITTERS...11 4.2.1 General Guidance...11 4.2.2 Enrolling Type..11 4.2.3 Enroll/Delete Sensors..11 4.2.4 Enroll/Delete Keyfob Transmitters..11 4.2.5 Enroll/Delete Wireless Commander.11 4.2.6 Enroll/Delete 2-Way Keypad.11 4.2.7 Enroll/Delete Wireless Siren.11 4.2.8 Enroll/Delete Proximity Tags.11
4.6 GSM Auto Detection... 25 4.7 PowerLink Auto Detection.. 25 4.8 DEFINING OUTPUT PARAMETERS. 25
4.8.1 Preliminary Guidance.. 25 4.8.2 Define PGM.. 26 4.8.3 Defining INT/STRB.. 26 4.8.4 X-10 GENERAL DEF.. 26 4.8.5 X-10 UNIT DEFINE.. 26

4.9 DEFINE VOICE... 28

4.9.1 Record Speech.. 28 4.9.2 Speech Box Mode.. 28
4.10 DIAGNOSTIC TEST.. 29 4.11 USER FUNCTIONS.. 29 4.12 RETRIEVING FACTORY DEFAULTS. 30 4.13 SERIAL NUMBER.. 30 4.14 CALLING UPLOAD/DOWNLOAD SERVER. 30 4.15 ENABLING/DISABLING PARTITIONS.. 30 4.16 WALK-TEST... 31 5. TESTING PROCEDURES.. 31
5.1 Preparations.. 31 5.2 Diagnostic Test.. 31 5.3 Keyfob Transmitter Test.. 31 5.4 Appliance ON/OFF Test.. 31 5.5 Emergency Transmitter Test.. 32
4.3 DEFINING ZONE TYPES, NAMES, CHIME ZONES & PARTITION.. 13 4.4 DEFINING CONTROL PANEL PARAMETERS. 14
4.4.1 Preliminary Guidance...14 4.4.2 Entry Delays 1&2..14 4.4.3 Exit Delay...14 4.4.4 Bell Time...14 4.4.5 Abort Time..14 4.4.6 Alarm Cancel...15 4.4.7 Quick Arm...15 4.4.8 Bypass...15 4.4.9 Exit Mode...15 4.4.10 Piezo Beeps...15 4.4.11 Trouble Beeps..15 4.4.12 Panic Alarm...15 4.4.13 Swinger Stop...15 4.4.14 Cross Zoning...15 4.4.15 Supervision...15 4.4.16 NOT READY..15 4.4.17 AUX Button A...15 4.4.18 AUX Button B 2-W-KF..16 4.4.19 Jam Detect..16 4.4.20 Latchkey...16 4.4.21 Not Active...16

6. MAINTENANCE.. 32

6.1 Dismounting the Control Panel.. 32 6.2 Replacing the Backup Battery.. 32 6.3 Fuse... 32 6.4 Replacing/Relocating Detectors.. 32
7. READING THE EVENT LOG.. 32 APPENDIX A. Detector Deployment & Transmitter Assignments... 33
A1. Detector Deployment Plan.. 33 A2. Keyfob Transmitter List.. 33 A3. Emergency Transmitter List.. 34 A4. Non-Alarm Transmitter List.. 34
APPENDIX B. X-10 Unit & PGM Output Assignments 34 APPENDIX C. Event Codes.. 35
Contact ID Event Codes.. 35 SIA Event Codes... 35 4/2 Event Codes.. 35 Understanding the Scancom Reporting Protocol Data Format.... 36

2. SPECIFICATIONS

2.1 General Data
Zones Number: 28 wireless, 2 hardwired (zones 29 & 30). Hardwired Zone Requirements: 2.2 k E.O.L. resistance (max. resistance of wires 220 ). Zone Types: Interior follower, interior, perimeter, perimeter follower, delay 1, delay 2, 24h silent, 24h audible, fire, nonalarm, emergency, gas, flood, temperature and home / delay. User Codes: 8 codes, 4 digits each (9999 different combinations). Code 0000 is not allowed. Control Facilities: - Integral keypad - PowerCode / Code-Secure hand-held transmitters - One-way / two-way keypads - Optional Built-In Proximity Tag Reader - Web interface via optional PowerLink module - SMS commands via optional GSM/GPRS module - Remote control by telephone Display: Single line, Backlit 16-character LCD. Arming Modes: AWAY, HOME, AWAY-INSTANT, HOMEINSTANT, LATCHKEY, FORCED, BYPASS. Alarm inhibited during a single arming period (swinger stop) after: 1, 2, 3, alarm/tamper/fault, or not inhibited (programmable / selectable). Alarm Types: Silent alarm, siren alarm or sounder (internal) alarm, in accordance with zone attributes. Siren Signals: Continuous (intrusion / 24 hours / panic); triple pulse - pause - triple pulse. (fire). Siren (bell) Timeout: Programmable Internal Sounder Output: At least 85 dBA at 10 ft (3 m) Supervision: Programmable time frame for inactivity alert Special Functions: - Speech and sound control - X10 - an international and open industry standard for communication among electronic devices used for home automation (up to fifteen X-10 units) - Chime zones - Diagnostic test and event log - Local and Remote Programming over Telephone, GSM /GPRS connections - Calling for help by using an emergency transmitter - Tracking inactivity of elderly, physically handicapped and infirm people - Message center (recording and playback) - Two-way voice communication Data Retrieval: Status, alarm memory, trouble, event log. Real Time Clock (RTC): The control panel keeps and displays time and date. This feature is also used for the log file by providing the date and time of each event. In addition, it is used for the Scheduler where activity of a device is performed according to a specific time and date selection. Compliance with U.S. Standards: Meets FCC Part 15 and Part 68 requirements. UL1637, UL1635, UL1023, UL985, ULC-S545-02, ULC C1023. Compliance with CE Standards: EN 50131-3, EN301489-3,7, EN 50130-4, EN60950, Aka ETSI TS 0210, ATS-3 According to the European standard EN50131-1, the PowerMax Pro security grading is 2 "low to medium risk" and environmental classification is II "indoor general" and the power supply type is A. The PowerMax Pro is compatible with the RTTE requirements - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999. GSM standards: Europe : Complies with CE standards 3GPP TS 51.010-1, EN 301 511, EN301489-7 USA: FCC 47 Part 22 (GSM850) and Part 24 (GSM 1900). EMC standard: FCC 47 Part 15. SAR standards: FCC rule 2.1093, FCC Docket 96-326 & Supplement C to OET Bulletin 65

2.5 Physical Properties

Operating Temp. Range: 14F to 120F (-10C to 49C) Storage Temp. Range: -4F to 140F (-20C to 60C) Humidity: 85% relative humidity, @ 30C (86F) Size: 10-13/16 x 8 x 2-1/8 in. (275 x 203 x 55 mm) Weight: 990g (2.2 pounds) without batteries Color: Silver or white

3. INSTALLATION

Note: The system must be installed in accordance with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72.
3.1 Unpacking the Equipment
Open the cardboard packing box and check whether all items have been included. If you find out that an item is missing, contact your vendor or dealer immediately.
Gather up all transmitters and detectors used in the system and mark each one in accordance with your deployment plan. Program the system now as instructed in the programming section.

3.4 Mounting

Required tool: Philips screwdriver #2. PowerMax Pro mounting process is shown in Figure 3.1a 3.1k.
3.2 Supplying Power to the Unit
Connect power to the PowerMax Pro as described in Figure 3.1f. Alternatively, you may power up from the backup battery, as shown in Figure 3.1h. Disregard any trouble indications pertaining to lack of battery or lack of telephone line connection.
3.5 Back Unit Mounting and Wiring
Required tools: Cutter and slotted screwdriver - 3 mm blade. PowerMax Pro wiring is shown in Figures 3.1b and c. Locate the terminal block housed in the expander card located on the upper left side of the back unit and make the necessary connections.
3.3 System Planning & Programming
It pays to plan ahead - use the tables in appendices A and B at the end of this guide to register the intended location of each detector, the holder and assignment of each transmitter and the control plan for the X-10 units.
Separate the back unit from the front unit

Back unit

Release screws
Positiong the back unit on the desired mounting location and mark 4 drilling points on mounting surface
Back unit Drill 4 holes and insert wall anchors
Fasten the back unit with 4 screws
Figure 3.1a Back Unit Mounting

3.5.1 Phone Wiring

PHONE WIRING USING RJ CONNECTORS
Connect the receptacles of supplied flat cables (2 - 5 cables according to options) to the back units plugs. The receptacles with strain relief clip are for the front unit - do not connect to the back unit! Strain relief clip
For all countries except north America: Connect telephone cable to SET connector and telephone line cable to LINE connector (through the desired wiring cable entry).

PHONE WIRING USING TERMINAL BLOCK CONNECTORS (NORTH AMERICA)

8-POSITION RJ-31X PLUG

BROWN RED GREEN 1

RJ-31X JACK

GRAY 5 RED LINE FROM STREET BROWN

RJ-31X

HOUSE PHONES

RJ-31X CORD

Figure 3.1b - Wiring Phone wiring in the UK: Line terminals must be connected to pins 2 and 5 of the wall jack. For all installations: If DSL service is present on the phone line, you must route the phone line through a DSL filter (refer to MESSAGE TO THE INSTALLER on page 2 for further details).
3.5.2 Zones and Sirens Wiring

SITE EXTERNAL SIREN

SITE INTERNAL SIREN OR STROBE
DC DC ZONE ZONE GND V+ GND +12V PGM SRN +12V SRN IN + IN - INT EXT

ZONE 29 / ZONE 30

CONNECT WIRED DETECTORS AS FOLLOWS:
GND V+(*) ZONE 29 / ZONE 30 GND V+ (*)
TAMP Alarm Power N.C. N.C.

Alarm N.C.

Detector with Tamper switch
Detector without Tamper switch
Note Regarding zones 29 & 30, the Control Panel sees a specific resistance according to the event, as follows: Normal (no alarm & no tamper): 2.2 k Alarm event: 4.4 k Tamper event: Infinite resistance

Figure 3.1c - Wiring

Notes: * Zone 29/GND and Zone 30/GND terminals can be connected to a normally closed contact of a detector, switch (for example a Tamper switch of any device), or a pushbutton, via a 2.2 K resistor. The 12V terminal can be used to supply 12V (up to 36mA) to a detector (if necessary). ** Both +12V terminals are identical (shorted together). The EXT terminal can be used to trigger an external siren. The INT terminal can be programmed for an "internal siren" or "strobe" (see DEFINE OUTPUTS - DEFINE INT/STRB in par. 4.8). The +12V and "GND" terminals can be connected to a siren (for constant DC power supply) not applicable in North America. WARNING! When an Internal GSM module is connected, the CELL/PC port of the Dual RS-232 module cannot be used for PC connection. In this case, either remove the Internal GSM or use the PL/PC connector. IMPORTANT! The terminals for internal and external sirens are DC outputs intended for 12V sirens. Connecting a loudspeaker to any of these outputs will cause a short circuit and will damage the unit.
If you need a wireless external siren, you may install an X-10 siren module which is triggered by a signal transmitted via the built-in electrical wiring of the protected site. This siren can replace the regular external siren or complement it without laying out additional wires. Of course, such a siren can be used only in conjunction with an optional power-line interface module. The X-10 siren is ready to function upon connection to an electrical power outlet, without re-programming the PowerMax Pro. You only have to set the HOUSE CODE and the UNIT CODE selectors on the X-10 siren as follows: House Code: Set this selector to the letter that follows, by alphabetical order, the letter that you programmed as a house code for the protected premises. For example, if the programmed house code is J, set the siren house code selector to K. Note: If the programmed house code letter is P (which is the last programmable letter), select A for the siren. Unit Code: The siren will function only if you set the unit code selector to 1.

3.5.3 Installing an Optional X-10 Siren
The control panel can be equipped with an optional dual RS-232 module for serial data interchange with a local computer (see Figure 3.1d). The dual RS-232 module permits any two simultaneous device connections such as: internal PowerLink, Local PC programming, and External GSM module.

Dual RS-232 adapter

3.5.4 Dual RS-232 Module Mounting
1. Dual RS-232 module. 2. Audio Module Note: The Audio Module terminal strip should be wired to the external Speech Box terminal strip, according to the markings on both terminal strips.

Back Unit

RJ-45 or RJ-31X (USA)
Figure 3.1d - Connecting to a Computer
Connector for internal POWERLINK or PC

Connector for GSM or PC

3.5.5 Audio Module Mounting
Figure 3.1e - Other Optional Modules Mounting
The Audio module allows the connection of an external wired Speech box module. The Speech Box is a wired remote speaker and microphone sensor for indoor use, which provides remote audio capability to enable two-way voice communication, between the user and the central station or private telephone, via the PowerMax Pro control panel. Press the dual RS-232 and AUDIO modules into the marked locations (see Figure 3.1e), until a click is heard.
3.5.6 Power Cable Connection
Connect the power cable and close the control panel as shown in Figure 3.1f. Socket-outlet shall be installed near the equipment and shall be easily accessible. The connection of the power supply to the PowerMax Pro unit can be performed through two options, as follows: Through connection of the power cable to the internal power supply, as shown in Figure 3.1f. -orThrough direct connection of the 12.5 VDC power supply to the expander card via the wall mounted switched AC/DC power supply (supplied by Visonic), as shown in Figure 3.1g.
Remove the cable entry knockout(s) and enter the power cable.
Extract either of these cable clamps for use in the next step.
Power cable clamp options For thin For thick cable cable (reversed clamp)
Power supply safety cover Power supply Power terminal strip supply unit a) Insert the power cable through the desired wiring channel (see step 1) and route it to the power supply unit. b) Pull out the power supply safety cover. c) Connect the two wires of the power cable to the power supply terminal strip with screwdriver. d) Verify that the wires are tightly fastened by the screws of the terminal strip. e) Fasten the power cable by its clamp (see also step 2 - this clamp can be reversed to fit thick/thin cable) f) Close the safety cover.

4.2.6 Enroll/Delete 2-Way Keypad
The 2-way keypad, type MKP-150/151, enables the user to remotely control the system and also to receive data from the system (status, alarm and trouble data). To enroll up to two 2-way keypads, refer to Figure 4.2. Note: MKP-150/151 is not compatible for use when partition is enabled.
4.2.7 Enroll/Delete Wireless Siren
The wireless siren is a remote siren that is activated upon predefined events by the PowerMax Pro system. To enroll / delete up to 2 wireless sirens, refer to Figure 4.2.

4.2.2 Enrolling Type

Here you determine whether to enroll a wireless sensor by normal transmission or by sensor Tamper function (opening its cover). Options: normal, or by tamper.
4.2.8 Enroll/Delete Proximity Tags
Proximity tags enable authorized people to enter restricted areas. Presenting valid proximity tag, while the system is armed, causes the system to disarm. Presenting valid proximity tag, while the system is disarmed, causes the system to be armed in AWAY (optional HOME) mode. To enroll / delete proximity tags, refer to Figure 4.2. Note: Proximity tags are used on control panels with installed Proximity readers (not standard on UK versions). Proximity tags are not compatible for use when partition is enabled.
4.2.3 Enroll/Delete Sensors
Wired and wireless sensors can be enrolled into the PowerMax Pro. To enroll / delete sensors, refer to Figure 4.2. Before enrolling, the lens at the front of PIR and dual-technology sensors should be masked to prevent inadvertent transmission. Make sure that magnetic contact transmitters are together with their magnets, to prevent them from sending out alarm transmissions.

ENROLLING TYPE

normal enroll by tamper
ENROLL SENSORS SET SENSITIV. higher sensitivity lower sensitivity Select by or ZONE No: - -
ENROLL KEYFOB Keyfob No: -

(****)

Keyfob No: 5

[Keyfob No.] (e.g. 5)

Keyfob No: 5 <OFF> TO DELETE

TRANSMIT NOW

[wired/WL Zone No. 01-30] (e.g. 05)

READY WALK TEST

[wired Zone No. 29/30] (e.g. 29)
[WL Zone No. 01-28] (e.g. 05)
ZONE No: 29 <OK> TO ENROLL USER SETTING INSTALLER MODE ENTER CODE
ZONE No: 05 TRANSMIT NOW [Initiate transmission)

ZONE No: 05

(press any key) (**)

Partition Partition 1

[select partition 1 - 4]
<OFF> TO DELETE ZONE No: 05

KEYFOB No: 05

ZONE No: 29
for next enrolling action

(**) (***)

Deleting a Keyfob
Applies only for next Note: in Partition mode when enrolling action
Enrolling wired sensor Enrolling a WL Sensor
ENROL WL 1WAY KP 1way kp No :

[WL 1-way keypad No. 1 to 8] (e.g. 5)
Deleting wired/ WL sensor
Enrolling a Keyfob (*****)
ENROL WL 2WAY KP 2way kp No:
1. NEW INSTL CODE 2. ENROLLING 3. DEFINE ZONES

2way kp No : 2

[MKP-150/151 No. 1 or 2] (e.g. 2)
1way kp No : 5 TRANSMIT NOW press key until red LED lights
1way kp No : 5 <OFF> TO DELETE
2way kp No : 2 <OFF> TO DELETE
15. PARTITIONING <OK> TO EXIT
Note: Partitioning is an optional feature

1way kp No: 5

TRANSMIT NOW Press MKP150/151 back tamper switch once (see MKP150/151 inst. instructions) 2way kp No: 2

2way kp No: 2

Deleting a wireless Commander MCM-140+
Note: Applies only when in Partition mode
Enrolling a wireless keypad MKP-150/151
Deleting a wireless keypad MKP-150/151
Enrolling a wireless Commander MCM-140+
ENROL WL SIREN SIREN No :
[WL siren No. 1 or 2] (e.g. 2)
ENROLL PROX TAG Tag No: -

Tag No: 5

siren No : 2 TRANSMIT NOW

siren No : 2

(Prox tag No.) (e.g. 5)
Momentarily press the wireless siren self-test button until a squawk is heard (1 sec. approx.)

siren No: 2

Open WL siren cover and remove its battery
<OFF> TO DELETE siren No: 2

PRESENT TAG

<OFF> TO DELETE

Present tag (**)

Tag No: 05
Enrolling a wireless siren
Deleting a wireless siren

Enrolling a Prox tag

Deleting a prox tag

* ** ***

Figure 4.2 - Enrolling / Deleting Wireless Sensors / Keyfobs / Wireless Commanders / Wireless Sirens Keyfob & proximity tags enrolling can be performed by **** Select "higher" sensitivity for far wireless sensor, the installer or by the user (via USER SETTINGS menu). "lower" for near sensors. Black box in the display means that a device is ***** MKP-150/151 is not compatible for use when partition enrolled (the system has learned its ID). No black is enabled. box indicates that the device is not enrolled. Note: This changes the RF range during enrolling only Initiate either normal transmission or the sensor and does not affect the performance of the sensor. tamper function (see ENROLLING TYPE, Par. 4.2.2).

Key Functionality Moves the cursor from left to right. Long press for speed. Moves the cursor from right to left. Long press for speed. Scrolls upward the sequence of inserted digits. Long press for speed. Scrolls downward the sequence of inserted digits. Long press for speed. Places cursor to extreme right position of edit string and shows the last 16 digits of edit string. Reverts to previous or top menu without saving the edit string. Reverts to "<OK> TO EXIT" without saving the edit string. Saves and reverts to previous menu. Clears all digits to the right of cursor. Clears one digit by cursor. Selects between uppercase or lowercase digits.
4.5.1 PSTN / GSM (Fig. 4.5 Detail A)
Area Code [Fig 4.5.1(1)] Here you enter the system tel. area code (up to 4 digits). Line Prefix [Fig 4.5.1(2)] Here you enter the number that is used as a prefix to access an outside telephone line (if exists). Dial Method [Fig 4.5.1(3)] Here you determine the dialing method used by the automatic dialer built into the PowerMax Pro control panel. The options are: Pulse and tone (dtmf). GSM Keep Alive [Fig 4.5.1(4)] Here you prevent the GSM service provider from disconnecting the GSM line if the user has not initiated any outgoing telephone calls during the last 28 days. The options are: disable and every 28 days. Note: A test message is sent to the first available SMS number. If this does not exist then it makes a call to the first private number.

4.5.2 GPRS / BB

(Fig. 4.5 Detail B) The GSM/GPRS module is capable of communicating with the Central Station receiver by GPRS, GSM Voice and SMS channels. Each of the channels can be separately enabled or disabled in order to allow or prohibit the module from using it for the event reporting. If all channels are enabled, the GSM/GPRS module will always try GPRS first. If fails, it will try GSM Voice. If fails, it will try any other possible method (PSTN, Broadband) and only then it will try SMS. This is due to the fact that SMS is the most
Note: The "" digit replaces the "@" digit which is not included in the PowerMax Pro editor. PIN Code [Fig 4.5.2(7] Enter PIN code of the SIM card installed in the PowerMax Pro unit (up to 16 digits). Force Home Network [Fig 4.5.2(8] Here you determine whether to force the SIM card to use the home network only and not to select another network in case the home network cannot be found. The options are: disable and enable.

GSM/GPRS [Fig 4.5.3(20b)] Here you determine if the GSM/GPRS line disconnection will be reported or not and determine the delay between detection of line disconnection and report failure. If the telephone line is disconnected, the message "GSM line fail" will be stored in the event log. The options are: don't report, 2 minutes, 5 minutes, 15 minutes, or 30 minutes. PSTN Up / Down [Fig 4.5.3(21)] Remote Access [Fig 4.5.3(21a)] Here you give or deny permission to access the system and exercise control from a remote telephone. The options are: rem. access ON and rem. access OFF. Mast. Downl Code [Fig 4.5.3(21b)] Here you determine the master installer 4-digit password for downloading/uploading data into/from the PowerMax Pro memory. Attention! If "0000" is used, it will not enable connection of the PowerMax Pro to the PC for upload/download purpose. Inst. Downl Code [Fig 4.5.3(21c)] Here you determine the installer 4-digit password for downloading data into the PowerMax Pro memory. Attention! If "0000" is used, it will not enable connection of the PowerMax Pro to the PC for upload/download purpose. Upload Option [Fig 4.5.3(21d)] Here you determine whether the PowerMax Pro data can be uploaded into a computer while the system is in disarm state or at any time (in HOME/AWAY arming & disarm state). The options are: when system OFF and any time Up Download Tel# [Fig 4.5.3(21e)] Here you enter the telephone number (up to 16 digits) of the UL/DL server. Note: Only for use with control panels monitored by compatible central stations. Leave empty if not used. GPRS Up / Down [Fig 4.5.3(22)] My SIM Tel. # [Fig 4.5.3(22a)] Here you enter the PowerMax SIM card telephone number. The central station dials this number when it needs to connect to the PowerMax Pro for uploading / downloading data. 1st Caller ID# [Fig 4.5.3(22b)] Here you determine the 1st VDNS receiver telephone number. When the PowerMax Pro responds to an incoming call from the telephone number defined here, it creates a connection to the VDNS for uploading / downloading data. 2nd Caller ID# [Fig 4.5.3(22c)] Here you determine the 2nd VDNS receiver telephone number. When the PowerMax Pro responds to an incoming call from the telephone number defined here, it creates a connection to that VDNS for uploading / downloading data. 2 Way Voice Def. [Fig 4.5.3(23)] Send 2 WV Code [Fig 4.5.3(23a)] - see note in Fig. 4.5 Detail C Here you determine whether the system will send two-way voice code to the central station (to turn the central station from data communication to voice communication state) by using pre-selected SIA or Contact-ID communication format only. The options are: send and don't send. Two Way Voice Central Stations [Fig 4.5.3(23b)] - see note in Fig. 4.5 Detail C Here you select the timeout for 2-way voice communication with Central Stations, or enable the central station to ring back for 2-way voice function. This option is applicable only after reporting an event to the central station. (The central

station person can press [3] for listen-in", [1] for "speak out" or [6] for listening and speaking). The options are: 10, 45, 60, 90 seconds, 2 minutes, ring back and disable (no two-way voice communication). Note: If "Ring Back" is selected, you should select "Disable Report" for private telephone (see par. 4.5.4(1) - Reporting to Private Telephones), otherwise the central station will establish communication with the PowerMax Pro (after an event occurrence) in the normal manner (and not after one ring). Ringback Time [Fig 4.5.3(23c)] - see note in Fig. 4.5 Detail C Here you determine the period during which the central station can establish 2-way voice communication with the PowerMax Pro (after 1 ring), if: A. Alarm type message was received by central station. B. Ring Back function was selected [see par. 4.5.3(23b)]. The options are: 1, 3, 5 or 10 minutes. Ambient Level [Fig 4.5.3(23d)] Here you select the ambient noise level of the installation. If it is a relatively noisy environment, set it to High (default setting). If it is a very quiet environment, set to Low. The options are: low and high. Report Cnfrm Alarm [Fig 4.5.3(24)] - see note in Fig. 4.5 Detail C Here you determine whether the system will report whenever 2 or more events (confirmed alarm) occur during a specific period (see par. 4.4.33). Available options are: enable report, disable report, enable + bypass (enabling report and bypassing the detector - applicable to PowerMax Pro that is compatible with DD243 standard). Report 24H Zones [Fig 4.5.3(25)] Here you determine whether 24 hour (silent and audible) zones will function as normal 24 hour zones or as panic zones. The options are: both original, audible as panic, silent as panic, or both as panic. Recent Close [Fig 4.5.3(26)] Here you enable or disable the recent closing report, that is sent to the central station if an alarm occurs within 2 minutes from the expiry of the exit delay. The options are: recent close ON and recent close OFF. Zone restore [Fig 4.5.3(27)] Here you determine whether a zone restore will be reported or not. The options are: report restore and don't report. System Inactivity Report [Fig 4.5.3(28)] Here you determine whether the central station will receive a message if the system is inactive (not armed) during a defined period (days). The options are: disable, rep. after 7d, rep. after 14d, rep. after 30d, rep. after 90d.
4.5.4 Private Report (Fig. 4.5 Detail D) Report To Private [Fig 4.5.4(1)] Here you determine which event groups will be reported to private telephone subscribers. The options are as follows: Term Description all All messages all (-op/cl) All messages, except open/close all (-alerts) All messages, except alerts alarms Alarm messages alerts Alert messages op/cl Open/close disable report No message will be reported Note: All means all events including the L. BAT and AC FAIL trouble messages.
Voice report [Fig 4.5.4(2)] 1st Private Tel# [Fig 4.5.4(2a)] Here you program the 1st telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 2nd Private Tel# [Fig 4.5.4(2b)] Here you program the 2nd telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 3rd Private Tel# [Fig 4.5.4(2c)] Here you program the 3rd telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 4th Private Tel# [Fig 4.5.4(2d)] Here you program the 4th telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. Redial Attempts [Fig 4.5.4(2e)] Here you determine the number of times the communicator will dial the called partys number (private telephone). The options are: 1, 2, 3 and 4 attempts. Attention! A maximum of 2 dialing attempts is permitted by the Australian Telecommunication Authority.

4.8.3 Defining INT/STRB

Here you determine whether the INT output will be used for an internal siren or for a strobe. If strobe is selected, the INT output will be activated when an alarm occurs until the system is disarmed (i.e. clearing alarm memory).

4.8.4 X-10 GENERAL DEF

For X-10 devices, you can select the following actions: FLASH ON ALARM - you can select no flash or all light flash, to control X-10 lighting devices in alarm conditions. TRBL INDICATION - you can select don't indicate or indicate for X-10 failure indication by the TROUBLE LED. FAIL REPORT - you can select report to central station 1, report to central station 2, report to private telephone and send SMS, for X-10 devices failure reporting.

DEFINE PGM

DEFINE INT/STRB

internal siren strobe

X-10 GENERAL DEF See detail A (next page)
X-10 UNIT DEFINE SET HOUSE CODE
house code =A house code =B house code =P
READY WALK TEST USER SETTINGS INSTALLER MODE INSTALLER MODE ENTER CODE

ONE WAY UNIT

TWO WAY UNIT Enter learn Mode (Turn X-10 to Learn mode) if already enrolled <OFF> to Delete

(enter device No.)

device No.
1. NEW INSTL CODE 2. ENROLLING 3. DEFINE ZONES 4. DEFINE PANEL 5. DEFINE COMM 8. DEFINE OUTPUTS 9. DEFINE VOICE
<OK> to Enroll PLEASE WAIT enroll fail Enroll FAIL

D- -: TYPE/FEATURE

enroll OK <OK> to test Exit Learn Mode (Exit X-10 Learn mode) PLEASE WAIT test OK

test fail PGM (*)

Dxx: PULSE TIME pulse time 2s pulse time 30s pulse time 2m pulse time 4m Dxx: LOCATION
not installed attic back door basement (***) bathroom custom 5
PGM (*) Dxx: BY ARM AWAY disable turn on turn off pulse active PGM (*) Dxx: BY DELAY disable turn on turn off pulse active PGM (*) Dxx: BY ARM HOME disable turn on turn off pulse active PGM (*) Dxx: BY KEYFOB disable turn on turn off pulse active toggle
PGM (*) Dxx: BY DISARM disable turn on turn off pulse active PGM (*) Dxx: BY ZONES
PGM (*) Dxx: BY MEMORY disable turn on turn off pulse active
PGM: BY LINE FAIL by line fail no by line fail yes
) Note:PGM BY LINE FAIL function is applicable for PGM only - not for X-10.
a - zone c - zone b - zone

(SELECT BY OR

x - zone

Z: _ _

(ENTER ZONE NUMBERS)
disable turn on turn off pulse active toggle
Figure 4.8 - Define Outputs Flow Chart
* ** If PGM is selected, the letters "PGM" will be displayed instead of "Dxx". Upon selecting any one of the 3 options (zone a, b and c) you may enter a zone number and then select "disable", "turn on", "turn off", "pulse active" or "toggle".
The currently saved option is displayed with a dark box at the right side. To review the options, repeatedly click button until the desired option is displayed, then click (a dark box will be displayed at the right side). For zone name list, refer to paragraph 4.3 (DEFINE ZONE TYPES). Each X-10 unit's default zone name is "Not installed".

(see figure 4.1a)

10. DIAGNOSTICS

NON-PARTITIONING ONLY

WL SENSORS TEST DIAG. TESTING WL SIRENS TEST S1 CPU WAIT S1 S2 CPU=STRONG CPU K1 K2 WL KEYPADS TEST K1 CPU WAIT CPU=STRONG CPU GPRS CONN. TEST PLEASE WAIT. UNIT IS OK LAN CONNECT. TEST PLEASE WAIT. UNIT IS OK

(Perform walk test)

BATHROOM Z19 STRONG DIAG. TESTING FRONT DOOR
Example of test result display
Example PLEASE WAIT. of test (alternating for 5 sec.) result S2 CPU=STRONG display Note Z1 POOR STRONG/GOOD/POOR/ Example NOT OK (with siren No., LIVING ROOM of test S1 or S2 before) is (alternating for 5 sec.) displayed according to the result display wireless siren signal Z2 OK strength). S1=siren 1. S2 = siren 2. (Each time the OK button is pressed, CPU = Control Panel Unit the next test result is displayed) = 2 way comm.

PLEASE WAIT. CPU=STRONG

Note STRONG/GOOD/POOR/ NOT OK (with keypad No., K1 or K2 before) is displayed according to the wireless siren signal strength). K1=keypad1 K2=keypad2 CPU = Control Panel Unit = 2 way comm.
(*) When the OK button is pressed, the test result takes
between 15 sec. to 4 mins. before it is displayed, d epending on the severity of the failure. See par. 4.10 for a complete list of possible GSM/GPRS messages.
Figure 4.10 - Diagnostic Test Flow Chart

4.11 USER FUNCTIONS

This mode provides you with a gateway to the user functions through the regular user programming menu. Refer to the User Guide for detailed procedures.
Caution! If after having programmed the user codes the system does not recognize your installer code, this indicates you must have programmed a user code that is identical with your installer code. If so, access the user menu and change the code that is identical with your installer code. This will re-validate your installer code.
4.12 RETRIEVING FACTORY DEFAULTS
If you want to reset the PowerMax Pro parameters to the factory default parameters, you should enter the installer menu and perform the "FACTORY DEFLT" function, as described in the right side illustration. To get the relevant parameters defaults, contact the PowerMax Pro dealer. Note: For PowerMax Pro with 2 installer codes, INSTALLER code and MASTER INSTALLER code, only the master installer code enables to perform factory default function.
Entering to/exit from the FACTORY DEFLT menu is shown in figure 4.1a 12. FACTORY DEFLT <OK> to restore ENTER CODE: This is a brief display after which all the factory defaults are retrieved.

D2. Emergency Zones

You can provide incapacitated, sick or elderly people with a miniature single-button transmitter to be carried on the neck like a pendant or to be worn on the wrist like a watch.

D6. Interior Zone

Interior zones are zones within the protected premises that have nothing to do with perimeter protection. Their most important feature is that they allow free movement within the protected area without initiating an alarm, provided that the system is armed in the "HOME" mode. People can therefore stay at home and move about freely, as long as they do not disturb a PERIMETER zone. Once the system is armed in the AWAY mode (all zones are protected), interior zones will initiate an alarm if violated.

D10. Perimeter Zones

Perimeter zones rely on detectors designed to protect doors, windows and walls. An immediate alarm is initiated when such a zone is violated by opening the door/window or by trying to break the wall.
D11. Perimeter Follower Zones
A non-entry/exit zone, typically a perimeter zone located on an entry/exit path treated as an entry/exit zone during an entry/exit time.
D7. Interior Follower Zones
"Interior Follower" zone is a zone that is located between entry/exit zone and the alarm system control panel. This zone is temporarily ignored by the alarm system during entry/exit delay periods, to enable you to walk (without causing an alarm) in front of a motion detector that is associated with the Interior Follower zone, after you enter through an entry zone on the way to the control panel, or when leaving the protected premises after system arming.

D12. Temperature Zone

D8. Home/Delay Zones
A zone type which functions as a delay zone when the system is armed HOME and as a perimeter-follower zone when the system is armed AWAY.
A temperature zone uses a wireless temperature detector to detect both indoor and outdoor temperatures and is permanently active. The detector monitors room temperature using an internal sensor. For outdoor or refrigerator installations, a waterproof temperature probe (optional) is used. There are a total of four fixed temperature points and the user can enable one or more temperature point. Upon detection of change in temperature a digital message is transmitted and the event is reported. 24 hour zones are mainly used for PANIC buttons, perimeter detectors and anti-tamper protection. They therefore trigger an alarm in both armed and disarmed states. 24 Hour Zone - Silent. - Upon detection, this zone initiates a silent alarm, meaning that the sirens do not function. Instead the PowerMax Pro dials telephone numbers and reports the event to central stations and/or to private telephones, as programmed. 24 Hour Zone - Audible. - Upon detection, this zone initiates a siren alarm. The PowerMax Pro also dials telephone numbers and reports the event to central stations and/or to private telephones, as programmed.

PowerMaxPro

Professional, all-in-one home security solution
Visonics PowerMaxPro brings an entirely new level of versatility, connectivity and style to the world of home security and control. This comprehensive, multifunction wireless solution fully meets consumers demands for attractive, easy-to-use, yet flexible, security and management of their homes. It delivers exceptional reliability, performance and ease of installation due to the uniquely robust, professionalgrade architecture.
Sleek contemporary design Comprehensive Internet-based operation and surveillance via PowerLink Wide range of remote control and reporting options via Internet, phone and SMS Simple, icon-based operation Easy installation - with intuitive menus and voice prompts Market-leading range of wireless peripherals Modular design - for easy upgrades Field-proven - in more than half a million installations
Elegant, all-in-one solution Wide range of wireless peripherals
Extend the value of your offering with these recommended wireless transmitters and detectors.*
Elegant design fits contemporary tastes and dcor Multiple, easily added internal and external communication
modules (GSM/GPRS/CDMA/IP) Extensive choice of additional modules, including two-way keyfob, factory-installed proximity card reader Seamless integration with Visonics PowerLink for Internet-based home control and surveillance Up to three RS232 terminals for external GSM, PowerLink and local PC communication Two interchangeable languages (optional) - ideal for multicultural markets Three partitions plus multiple common areas allows for multitenant residences, home and small offices/businesses, household help/guest living quarters, etc.

CO Detector

Keyfob

Two-way Keyfob

Enables streamlined operations and advanced services

Temperature Detector

Two-way Keypad

PowerLink Module

Easily added communication modules, interchangeable languages
- enable you to meet diverse needs whilst simplifying inventory management Easy, flexible OEM customisation - including panel shell, languages, display texts, voice prompts Opens the way to advanced applications

Smoke Detector

Remote Commander

GSM/GPRS Modules

Intelligent architecture
Full protection of all mission-critical components, including
internal power supply, main PCB and outputs Isolated battery compartment, providing up to 72 hours backup Diversity antenna for superb-quality transmission and reception Internal GSM module with optional external antenna improves cellular transmission and reception Internal PowerLink module - for Internet-based operation and surveillance Dedicated channels and side openings ensure easy wiring

Flood Detector

Magnetic Contact

Motion Detector

Built for easy installation, reliable operation

Network Camera

Indoor Siren

Outdoor Siren

Visual and audio system status notifications Easy-view large-font 16-character LCD Icon-based keypad - reduces training and support Easy-enrol, easy-use proximity tags and keyfobs Simple, menu-based programming Field-proven reliability Full ISO 9001 certification Complies with most international standards and regulations,
including FCC, CE, EN50131 Grade 2, WEEE, RoHS
*Partial list; contact Visonic to get a full list of more than 30 types of available accessories.

and PowerMax are registered trademarks of Visonic Ltd. Other names are the property of their owners. Visonic reserves the right to change information or specifications without notice. VISONIC LTD. POWERMAX PRO DATA SHEET ENG C-800240 (Rev.04) Designed by: Linor Ankri
Head Office Israel Tel (+972-3) Spain Tel (+34-91) U.S.A Tel (+860) Hong Kong Tel (+852) U.K. Tel (+44-870) Germany Tel (+49) 6960 Nordic Tel (+47) Poland Tel (+48-22) South Africa Tel (+27) 8668
For more information, visit us at: www.visonic.com or info@visonic.com