The input signals are amplified and output directly without sound processing. Therefore, you cannot activate sound field programs, the night listening mode, etc. while MULTI CH is selected as the input source.

A.SEL: AUTO

Currently selected audio input jack select setting

Function

Automatically selects input signals in the following order: (1) HDMI (2) Digital signals (3) Analog signals Selects only HDMI signals. When HDMI signals are not input, no sound is output. Selects only digital signals. When no signals are input, no sound is output. Selects only analog signals. If no analog signals are input, no sound is output.

HDMI COAX/OPT ANALOG

This feature is not available when no digital input jacks (OPTICAL, COAXIAL and HDMI) are assigned. In addition, HDMI is not available as an audio input jack select setting when the HDMI IN DVD and HDMI IN DTV/CBL jacks are not used. Use INPUT ASSIGNMENT in INPUT MENU to reassign the respective input jack (see page 68).
01EN_HTR-6140_U.book Page 35 Friday, February 1, 2008 2:26 PM
Displaying the current status of this unit on a video monitor
You can display the operating information of this unit on a video monitor.

Using your headphones

Connect a pair of headphones with a stereo analog audio cable plug to the PHONES jack on the front panel.
Turn on the video monitor connected to this unit. Press O DISPLAY. The current status screen appears in the OSD.
STATUS VOL:-40dB DVD Movie Viewing MOVIE Movie Spacious INPUT: DVD A.SEL: HDMI NIGHT:CINEMA (MID) [DISPLAY]:STATUS OFF
You can select the amount of time that the current status is displayed in the OSD by using the OSD-AMP parameter in OPTION MENU (see page 70).
When you select a sound field program, SILENT CINEMA mode is automatically activated (see page 39).
The OSD signal is not output at the DVR VIDEO OUT jacks and will not be recorded.
When you connect headphones, no signals are output at the speaker terminals. All Dolby Digital and DTS audio signals are mixed down to the left and right headphone channels.

Muting the audio output

Press J MUTE to mute the audio output. Press J MUTE again to resume the audio output. y
You can also rotate I VOLUME or press N VOLUME +/ to resume the audio output. You can adjust the muting level by using the MUTE TYPE parameter in SOUND MENU (see page 66). The MUTE indicator flashes in the front panel display when the audio output is muted and disappears from the front panel display when the audio output is resumed.

Pop/Rock

Hall Jazz Game

ENTERTAINMENT

TV Sports

Movie Spacious

2ch Stereo

STEREO

5ch Stereo 2ch Enhancer 5ch Enhancer

MUSIC ENHANCER

The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from each direction.
01EN_HTR-6140_U.book Page 39 Friday, February 1, 2008 2:26 PM
Enjoying 2-channel sources using the standard decoders
Signals input from 2-channel sources can also be played back on multi-channels. Press 5 AMP and then press QSUR. DECODE repeatedly to select a decoder. You can select from the following decoders depending on the type of source you are playing and your personal preference.
Decoder Functions Dolby Pro Logic processing for any sources Dolby Pro Logic II processing for movie sources Dolby Pro Logic II processing for music sources Dolby Pro Logic II processing for game sources Neural Surround processing for any sources
Using sound field programs without surround speakers (Virtual CINEMA DSP)
Virtual CINEMA DSP allows you to enjoy the CINEMA DSP programs without surround speakers by creating virtual speakers. If you set SUR. L/R SP to NONE (see page 64), Virtual CINEMA DSP is automatically activated whenever you select a CINEMA DSP program (see page 38). Note
Virtual CINEMA DSP will not be activated even when SUR. L/R SP is set to NONE (see page 64) in the following cases: when 5ch Stereo (see page 38) is selected. when headphones are connected to the PHONES jack.
Pro Logic PLII Movie PLII Music PLII Game Neural Sur.
Enjoying multi-channel sources and sound field programs with headphones (SILENT CINEMA)
SILENT CINEMA allows you to enjoy multi-channel music or movie sound, including Dolby Digital and DTS sources, through ordinary headphones. SILENT CINEMA is automatically activated whenever you connect headphones to the PHONES jack while listening to CINEMA DSP sound field programs (except for 5ch Stereo) (see page 38). When activated, the SILENT CINEMA indicator lights up in the front panel display.
Enjoying unprocessed input sources (Straight decoding mode)
When this unit is in the STRAIGHT mode, multi-channel sources are decoded straight into the appropriate channels without any additional effect processing. 2-channel stereo sources are output from only the front left and right speakers. Press M STRAIGHT (or press 5 AMP and then press C STRAIGHT) to select STRAIGHT. To deactivate the STRAIGHT mode, press M STRAIGHT (or press 5 AMP and then C STRAIGHT) again so that STRAIGHT disappears from the front panel display.

001 Preview

When you select XM as the input source, this unit automatically recalls the previously selected channel.
The XM Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks. If a status message or an error message appears in the front panel display or in the OSD, see the XM Satellite Radio section in Troubleshooting on page 78 for appropriate remedies.
Search for a channel by using one of the XM Satellite Radio search modes. To select a channel from the all channel list, see All Channel Search mode on page 48. To select a channel by category, see Category Search mode on page 48. To select a channel from the preset channels, see Preset Search mode on page 48. To select the desired channel directly by entering the channel number, see Direct Number Access mode on page 48.
You can use the Neural Surround decoder to enjoy the XM HD surround sound content of the XM Satellite Radio broadcasts in multi-channels (see page 39). You can set the XM Satellite Radio preset channels (see page 49). You can display the XM Satellite Radio information in the front panel display or in the OSD (see page 50).
01EN_HTR-6140_U.book Page 48 Friday, February 1, 2008 2:26 PM
Before performing operations, press 3XM to select XM as the input source.

All Channel Search mode

Press EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n) repeatedly to change the preset channel number (1 to 8).
Press BSEARCH MODE (or MSRCH MODE) repeatedly to select ALL CH SEARCH. Press EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n) repeatedly to search for a channel within all channels.
You can also select the preset channel number directly by pressing the numeric buttons (1 to 8) on the remote control.
Direct Number Access mode
Press MSRCH MODE repeatedly to select ALL CH SEARCH or CAT SEARCH. Press the numeric buttons (G) to enter the desired three-digit channel number. For example, to enter the number 123, press the numeric buttons as shown below.
You can search for a channel quickly by pressing and holding EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n). To display the XM Radio ID number displayed in the front panel display, select channel 0.

Category Search mode

Press BSEARCH MODE (or MSRCH MODE) repeatedly to select CAT SEARCH. Press DCATEGORY (or 8A-E/CAT. l / h) repeatedly to change the channel category. Press EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n) repeatedly to search for a channel within the selected channel category.

01EN_HTR-6140_U.book Page 54 Friday, February 1, 2008 2:26 PM
Setting the SIRIUS Satellite Radio preset channels
You can use this feature to store up to 40 SIRIUS Satellite Radio channels (A1 to E8: 8 preset channel numbers in each of the 5 preset channel groups). You can then recall any preset channel easily by selecting the preset channel group and number as described in Preset Search mode on page 53.
Press E PRESET/TUNING/CH l / h (or 8 PRESET/CH k / n) repeatedly to select a preset channel number (1 to 8) while the MEMORY indicator is flashing. The preset channel number appears in the front panel display.

AHair Na

Currently selected preset channel number
Search for a channel you want to set as a preset channel by using one of the SIRIUS Satellite Radio search modes. See Basic SIRIUS Satellite Radio operations on page 52 for details.
Press F MEMORY (or 9 MEMORY) to set the selected SIRIUS Satellite Radio channel as a preset channel while the MEMORY indicator is flashing. A colon (:) appears next to the preset channel number for confirmation, and the MEMORY indicator turns off in the front panel display.

001 SIRIUS Hit

A1:023 Hair Na
Press F MEMORY (or 9 MEMORY). The MEMORY indicator flashes in the front panel display for approximately 30 seconds.
Setting the Parental Lock
You can use the Parental Lock feature to limit the access to the desired SIRIUS Satellite channels. This unit automatically skips the locked channels when this unit is in the All Channel Search mode or Category Search mode and you search a channel by pressing E PRESET/TUNING/CH l / h (or 8 PRESET/CH k / n).
Press D CATEGORY (or 8 A-E/CAT. l / h) repeatedly to select a preset channel group (A to E) while the MEMORY indicator is flashing. The preset channel group letter appears in the front panel display.
Setting the code number and the locked channels
Use this feature to set the Parental Lock code number (PIN) and select the channels to be locked.
Press 5 AMP on the remote control and then press M MENU to display. Press 8 n to select MANUAL SETUP and then press 8 ENTER.

023 Hair N

Currently selected preset channel group

Pairing by using SET MENU
Use this feature to perform pairing with the video monitor. Select START PAIRING in INPUT MENU. See page 71 for details.
The Yamaha Bluetooth adapter can be paired with up to eight Bluetooth components. When pairing is conducted successfully with a ninth component and the pairing data is registered, the pairing data for the least recently used other component is cleared.

Quick pairing

To ensure security, a time limit of 8 minutes is set for the pairing operation. You are recommended to read and fully understand all the instructions before starting.
Playback of the Bluetooth component
Press OINPUT l / h repeatedly (or press 4 V-AUX/DOCK) to select V-AUX as the input source. Start playback of your Bluetooth component. When the connected Bluetooth adapter detects the Bluetooth component, BT connected and the DOCK indicator appears in the front panel display.
Press OINPUT l / h repeatedly (or press 4 V-AUX/DOCK) to select V-AUX as the input source. Turn on the Bluetooth component you want to pair with. Press and hold CBAND (or 7 BAND) for 3 seconds to start pairing. Once the Bluetooth adapter starts pairing, Searching. appears for a moment. While the Bluetooth adapter is in the pairing mode, DOCK indicator flashes in the front panel display. y
To cancel the pairing, press CBAND (or 7 BAND) again.
When you press 8 ENTER, the connected Bluetooth adapter searches and connect to the last connected Bluetooth component. If the Bluetooth adapter cannot find the Bluetooth component, Not found appears in the front panel display. To disconnect the Bluetooth adapter from the Bluetooth component, press 9 RETURN.
01EN_HTR-6140_U.book Page 60 Friday, February 1, 2008 2:26 PM

RECORDING

Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating instructions for those components. Notes
When this unit is set to the standby mode, you cannot record between other components connected to this unit. TONE CONTROL (see page 41) and VOLUME settings, speaker levels (see page 41) and the sound field programs (see page 38) do not affect recorded material. The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded. The XM Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks. The SIRIUS Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks. Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if your source component is connected to provide only digital signals, you cannot record the source. A given input source is not output on the same OUT (REC) channel. The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording. Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is turned off, this unit may distort the sound from other components. Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.

The MAX VOL. setting takes priority over the Initial Volume setting. For example, if INIT.VOL. is set to 20 dB and MAX VOL. is set to 30 dB, the volume level is automatically set to 30 dB when you turn on the power of this unit next time.

HDMI set H)HDMI SET

Use this feature to select the component to play back HDMI audio signals.
1 SOUND MENU H)HDMI SET SUPPORT AUDIO: HTR-6140
[p]/[[]:Select [ENTER]:Return
Initial volume INIT.VOL. Use this feature to set the volume level when the power of this unit is turned on. Choices: Off, MUTE, 80 dB to +16 dB Control step: 1 dB Note
The MAX VOL. setting takes priority over the INIT.VOL. setting.
Support audio S.AUDIO Use this feature to select whether to play back HDMI audio signals on this unit or on another HDMI component connected to the HDMI OUT jack on the rear panel of this unit.

Choice Functions

Plays back HDMI audio signals on this unit. The HDMI audio signals input at the HDMI input jacks of this unit are not output to the HDMI component connected to the HDMI OUT jack on the rear panel of this unit. Plays back HDMI audio signals on another HDMI component connected to the HDMI OUT jack.
This unit transmits audio and video signals input at the HDMI input jacks to the HDMI out jack only when this unit is turned on even if SUPPORT AUDIO is set to Other. Available audio/video signals depend on the specification of the connected video monitor. Refer to the instruction manual of each connected component.
01EN_HTR-6140_U.book Page 68 Friday, February 1, 2008 2:26 PM

2 INPUT MENU

Use this menu to reassign the input jacks, select the decoder mode or rename the input source.
;MANUAL SETUP 2 INPUT MENU. A)INPUT ASSIGNMENT B)INPUT RENAME C)VOLUME TRIM D)DECODER MODE E)MULTI CH SET [ ]/[ ]:Up/Down [ENTER]:Enter
For HDMI jacks 1 and 2 HDMI IN [1] HDMI IN [2] Choices: (1) DVD, DTV/CBL, V-AUX, DVR (2) DVD, DTV/CBL, V-AUX, DVR
2 INPUT MENU A)INPUT ASSIGNMENT HDMI IN. [IN1];;; DVD ( DVD ) [IN2];;;DTV/CBL (DTV/CBL ) [p]/[[]:Select

Input assignment

A)INPUT ASSIGNMENT Use this feature to assign the input jacks according to the component to be used if the initial settings of this unit do not correspond to your needs. Change the following parameters to reassign the respective jacks and effectively connect more components. Once the input jacks are reassigned, you can select the corresponding component by using OINPUT l / h (or the input selector buttons (4)). For COAXIAL INPUT jack 1 COAXIAL IN (1) Choices: (1) CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR
2 INPUT MENU A)INPUT ASSIGNMENT COAXIAL IN. (1);;;;; ( DVD DVD

[p]/[[]:Select

For OPTICAL INPUT jacks 2 and 3 OPTICAL IN (2) OPTICAL IN (3) Choices: (2) CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR (3) CD, MD/CD-R, DVD, DTV/CBL, V-AUX, DVR
2 INPUT MENU A)INPUT ASSIGNMENT OPTICAL IN. (2);;;;;DTV/CBL (DTV/CBL ) (3);;;;; CD ( CD ) [p]/[[]:Select
Input rename B)INPUT RENAME
Use this feature to change the name of the input source that appears in the OSD and in the front panel display.
2 INPUT MENU B)INPUT RENAME DVD -> DVD
[p]/[[]:Position [ ]/[ ]:Chara.
Press one of the input selector buttons (4) or E MULTI CH IN to select the input source you want to change the name of.

DVD DTV/CBL DVR

MULTI CH IN
Press 5 AMP and then press 8 l / h on the remote control to place the _ (underscore) under the space or the character you want to edit. Press 8 k / n to select the character you want to use and then press 8 l / h to move to the next space. Notes
You can use up to 8 characters for each input. Press 8 n to change the character in the following order, or press 8 k to go in the reverse order: A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#, *, , +, etc.)
You cannot select a specific item more than once.
01EN_HTR-6140_U.book Page 69 Friday, February 1, 2008 2:26 PM
Repeat steps 1 through 3 to rename each input source. Press 8 ENTER to exit from INPUT RENAME.
DTS decoder prioritize setting Choices: AUTO, DTS Select AUTO if you want this unit to automatically detect input signal types and select the appropriate input mode. Select DTS when you play back a DTS-CD.
Volume trim C)VOLUME TRIM
Use this feature to adjust the output volume of each source. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources. Choices: CD, MD/CD-R, TUNER, DVD, DTV/CBL, V-AUX, DVR, DOCK, MULTI CH, XM, SIRIUS Control range: 6.0 to +6.0 dB Control step: 1.0 dB Initial setting: 0.0 dB

Even if you set SSR PIN to RESET, this unit does not unlock the locked channels. The initial factory setting of the Parental Lock code number is 0000.
The settings you made are reflected next time you turn on this unit.
01EN_HTR-6140_U.book Page 77 Friday, February 1, 2008 2:26 PM
Tuner frequency step TU (Asia and General models only)
Use this feature to set the tuner frequency step according to the frequency spacing in your area. Choices: AM10/FM100, AM9/FM50 Select AM10/FM100 for North, Central and South America. Select AM9/FM50 for all other areas.

Initializing INIT.

Use this feature to reset all the parameters of this unit to the initial factory settings (see page 87). Choices: CANCEL, RESET Select CANCEL not to reset any parameters of this unit. Select RESET to reset the parameters of this unit. Notes
This setting completely resets all the parameters of this unit including the SET MENU parameters. However, the advanced setup menu parameters will not be initialized. The initial factory settings are activated next time you turn on this unit.
ADVANCED OPERATION English
01EN_HTR-6140_U.book Page 78 Friday, February 1, 2008 2:26 PM

Troubleshooting

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.

General

Problem
This unit fails to turn on or enters the standby mode soon after the power is turned on.
The power cable is not connected or the plug is not completely inserted. The speaker impedance setting is incorrect. The protection circuitry has been activated.

Remedy

Connect the power cable firmly. Set the speaker impedance to match your speakers. Make sure that all speaker wire connections on this unit and on all speakers are secure and that the wire for each connection does not touch anything other than its respective connection. Set this unit to the standby mode, disconnect the power cable, plug it back in after 30 seconds and then use it normally. Connect the cables properly. If the problem persists, the cables may be defective. Set an appropriate Audio input jack select. Set Audio input jack select to AUTO. Set Audio input jack select to AUTO or COAX/OPT. Select an appropriate input source with O INPUT l / h (or the input selector buttons(4)). Secure the connections. Select the front speakers with JSPEAKERS. Turn up the volume. Press JMUTE or N VOLUME +/ to resume audio output and then adjust the volume. Play a source whose signals can be reproduced by this unit. Connect HDMI components that support the HDCP copy protection standards. Set SUPPORT AUDIO to HTR-6140 in MANUAL SETUP.

See page 21 11

This unit has been exposed to a strong external electric shock (such as lightning or strong static electricity). No sound. Incorrect input or output cable connections. No appropriate Audio input jack select has been set. Audio input jack select is set to HDMI, COAX/OPT or ANALOG. Audio input jack select is set to ANALOG while playing a source encoded in Dolby Digital or DTS. No appropriate input source has been selected. Speaker connections are not secure. The front speakers to be used have not been selected properly. The volume is turned down. The sound is muted.

13-34 34

Signals this unit cannot reproduce are being input from a source component, such as a CD-ROM. The HDMI components connected to this unit do not support the HDCP copy protection standards. SUPPORT AUDIO is set to Other and HDMI audio signals are not being played back on this unit.
01EN_HTR-6140_U.book Page 79 Friday, February 1, 2008 2:26 PM
The sound suddenly goes off.
The protection circuitry has been activated because of a short circuit, etc.
Check that the impedance setting is correct. Check that the speaker wires are not touching each other and then turn this unit back on.

See page 21 35 11-

The sleep timer has turned off this unit. The sound is muted.
Turn on this unit, and play the source again. Press JMUTE or N VOLUME +/ to resume audio output. Connect the cables properly. If the problem persists, the cables may be defective. Adjust the SP LEVEL settings. This is not malfunction.
Sound is heard from the speaker on one side only. Only the center speaker outputs substantial sound.
Incorrect cable connections. Incorrect settings in SP LEVEL. When playing a monaural source with a CINEMA DSP program, the source signal is directed to the center channel, and the front and surround speakers output effect sounds. CENTER SP in SPEAKER SET is set to NONE. Some sound field programs do not output sounds from the center speaker. SUR. L/R SP in SPEAKER SET is set to NONE. This unit is in the STRAIGHT mode and a monaural source is being played back. FRONT B in SPEAKER SET is set to ZONE B.
No sound is heard from the center speaker.
Set CENTER SP to SML or LRG. Try another sound field program. Set SUR. L/R SP to SML or LRG. Press CSTRAIGHT so that STRAIGHT disappears from the front panel display. Set FRONT B to FRONT.
No sound is heard from the surround speakers.
No sound from the center, surround speakers when the FRONT B speakers are activated. No sound is heard from the subwoofer.
LFE/BASS OUT in SPEAKER SET is set to FRNT when a Dolby Digital or DTS signal is being played. LFE/BASS OUT in SPEAKER SET is set to SWFR or FRNT when a 2-channel source is being played. The source does not contain low-frequency bass signals.
Set LFE/BASS OUT to SWFR or BOTH.

This is not malfunction.

01EN_HTR-6140_U.book Page 80 Friday, February 1, 2008 2:26 PM
Dolby Digital or DTS sources cannot be played. (Dolby Digital or DTS indicator in the front panel display does not light up.) A humming sound is heard. The volume level cannot be increased, or the sound is distorted.
The connected component is not set to output Dolby Digital or DTS digital signals. Audio input jack select is set to ANALOG.
Make an appropriate setting following the operating instructions for your component. Set Audio input jack select to AUTO.

See page

Incorrect cable connections. You are attempting to set the volume level higher than the maximum volume level. The component connected to the AUDIO OUT (REC) jacks of this unit is turned off. It is not possible to record the sound effect with a recording component. The source component is not connected to the analog AUDIO IN jacks of this unit.

CH UNAUTH

NO SIGNAL

The XM Mini-Tuner is not receiving the XM satellite signal. Something may be blocking the XM antennas view of the satellites or the antenna is not properly aimed. The XM Mini-Tuner is acquiring audio or program information from the XM satellite signal. This message can also occur in weak XM signal conditions. Note that this unit may not respond to some operations while this message is displayed. The XM channel you selected is not currently broadcasting. The selected channel is not available. The channel may have been reassigned to a different channel number. This message may occur initially with a new XM Mini-Tuner or a XM Mini-Tuner that has not received XMs signal for an extended period.

LOADING

OFF AIR CH UNAVAILABLE
Check back at a later time; in the mean time, select another channel. Consult the latest channel guide at http://www.xmradio.com/ (US residents) and http://www.xmradio.ca/ (Canadian residents) for the current list of channels. For cases of a new XM Mini-Tuner or a XM Mini-Tuner that has not received XMs signal for an extended period, allow the XM Mini-Tuner to receive the XM satellite signal for at least 5 minutes and then try to select the channel again. No action required.

- - - -

No artist name or song title is available for this selection.
01EN_HTR-6140_U.book Page 83 Friday, February 1, 2008 2:26 PM

SIRIUS Satellite Radio

The antenna is not connected to the SiriusConnect tuner properly. The SiriusConnect tuner is not connected to the SIRIUS jack of this unit correctly. The SiriusConnect tuner is not connected to the AC wall outlet.
Check the connection of the antenna and SiriusConnect tuner. Check the connection of the SiriusConnect tuner and this unit. Connect the power cable of the SiriusConnect tuner to the AC wall outlet. Connect the SiriusConnect tuner that this unit supports, Adjust the orientation of the antenna of the SiriusConnect tuner. Use the ANTENNA INFO information in the front panel display or SIRIUS Information screen in the video monitor to check the antenna reception level. Wait until the updating is complete. Contact SIRIUS Satellite Radio to renew the subscription. Wait until the updating is complete. Contact SIRIUS Satellite Radio to subscribe the selected channel. URL: https://activate.siriusradio.com/ Phone: 1-888-539-SIRIUS (1-888-539-7474) Select another channel.

See page 51, 56

ANTENNA ERROR CHECK SR TUNER

NOT SUPPORTED ACQUIRING

This unit does not support the connected SIRIUS Satellite Radio tuner. The signal is too weak.

UPDATING

The SiriusConnect tuner is updating the channel list. The period of the subscription is end.

52 52

F/W UPDATING CALL SIRIUS (CALL 888-539-SIRIUS TO SUBSCRIBE) SUB UPDATED INVALID Not Available
The SiriusConnect tuner is updating the firmware. The selected channel is not subscribed.
The subscription information is updated. The selected channel is currently out of service. The operation you made is not available. Select another channel.
01EN_HTR-6140_U.book Page 84 Friday, February 1, 2008 2:26 PM

AUTO SETUP

Before AUTO SETUP

Error message Cause

Optimizer microphone is not connected.
Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. Unplug the headphones.

See page

Connect MIC!

Unplug HP!

Headphones are connected.

During AUTO SETUP

Front L/R channel signals are not detected. A surround channel signal is not detected. Background noise is too loud.
Check the front L/R speaker connections. Check the surround speaker connections. Try running AUTO SETUP in a quiet environment. Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone.
E-1:NO FRONT SP E-2:NO SUR.SP E-4:NOISY

E-6:NO MIC

The optimizer microphone was unplugged during the AUTO SETUP procedure. The optimizer microphone does not detect test tones.
Connect the supplied optimizer microphone to OPTIMIZER MIC jack on the front panel. Check the microphone setting. Check the speaker connections and placement.

E-7:NO SIGNAL

24 10, 11, 24
E-8:USER CANCEL E-9:INTERNAL ERROR
The AUTO SETUP procedure was cancelled due to user activity. An internal error occurred.
Run AUTO SETUP again. Run AUTO SETUP again.
01EN_HTR-6140_U.book Page 85 Friday, February 1, 2008 2:26 PM

After AUTO SETUP

Warning message Cause
Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. The distance between the nearest speaker and the furthest speaker is out of adjustable range. The difference of volume level among speakers is excessive. (No level correction is made.)

Unable to play

01EN_HTR-6140_U.book Page 86 Friday, February 1, 2008 2:26 PM

Bluetooth

The Bluetooth adapter and the Bluetooth component is in the middle of the pairing. The Bluetooth adapter and the Bluetooth component is in the middle of establishing the connection.

Searching.

Completed Canceled BT connected
The paring is completed. The paring is canceled. The connection between the Yamaha Bluetooth adapter (such as YBA-10, sold separately) and the Bluetooth component is established. The Bluetooth component is disconnected from the Yamaha Bluetooth adapter (such as YBA-10, sold separately). The Bluetooth adapter is not connected to the DOCK terminal. Connect the Yamaha Bluetooth adapter (such as YBA-10, sold separately) to the DOCK terminal.

No BT Adapter

01EN_HTR-6140_U.book Page 87 Friday, February 1, 2008 2:26 PM

Remote control

The remote control does not work nor function properly.

Wrong distance or angle.

The remote control functions within a maximum range of 6 m (20 ft) and no more than 30 degrees off-axis from the front panel. Reposition this unit.

See page 23

Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. The batteries are weak. The remote control code is not correctly set.
Replace all batteries. Set the remote control code correctly using List of remote control codes at the end of this manual. Try setting another code for the same manufacturer using List of remote control codes at the end of this manual.
Even if the remote control code is correctly set, there are some models that do not respond to the remote control.

Resetting the system

Use this feature to reset all the parameters of this unit to the initial factory settings.
This procedure completely resets all the parameters of this unit including the SET MENU parameters. However, the advanced setup menu parameters will not be initialized. The initial factory settings are activated next time you turn on this unit.
Press A STANDBY/ON on the front panel to set this unit to the standby mode. Press and hold K TONE CONTROL and then press A STANDBY/ON to turn on this unit. The advanced setup menu appears in the front panel display. Press L PROGRAM l / h to select INIT. Press M STRAIGHT repeatedly to select RESET. Select CANCEL to cancel the initialization procedure without making any changes. Press A STANDBY/ON to confirm your selection and set this unit to the standby mode.

SILENT CINEMA

Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound field so that accurate representations of all the sound field programs can be enjoyed on headphones.

LFE 0.1 channel

This channel reproduces low-frequency signals. The frequency range of this channel is from 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low-frequency range compared to the full-range reproduced by the other 5 channels in Dolby Digital or DTS 5.1-channel systems.

Virtual CINEMA DSP

Yamaha has developed a Virtual CINEMA DSP algorithm that allows you to enjoy DSP sound field surround effects even without any surround speakers by using virtual surround speakers. It is even possible to enjoy Virtual CINEMA DSP using a minimal two-speaker system that does not include a center speaker.

Neural Surround

Neural Surround represents the latest advancement in surround technology and has been adopted by XM Satellite Radio for digital radio broadcast of surround recordings and live events in surround sound. Neural Surround employs psychoacoustic frequency domain processing which allows delivery of a more detailed sound stage with superior channel separation and localization of audio elements.

PCM (Linear PCM)

Linear PCM is a signal format under which an analog audio signal is digitized, recorded and transmitted without using any compression. This is used as a method of recording CDs and DVD audio. The PCM system uses a technique for sampling the size of the analog signal per very small unit of time. Standing for Pulse Code Modulation, the analog signal is encoded as pulses and then modulated for recording.
01EN_HTR-6140_U.book Page 90 Friday, February 1, 2008 2:26 PM

Specifications

AUDIO SECTION
Minimum RMS Output Power for Front, Center, Surround [U.S.A. and Canada models] 1 kHz, 0.9% THD, 8 ... 105 W [Other models] 1 kHz, 0.9% THD, 6 ... 105 W Maximum Power for Front, Center, Surround (JEITA) 1 kHz, 10% THD, 6 .. 130 W Dynamic Power [U.S.A. and Canada models] (IHF, 8/6/4/2 ).. 90/110/130/150 W [Other models] (IHF, 6/4/2 ).. 100/110/125 W Dynamic Headroom [U.S.A. and Canada models] 8 ... 0.27 dB Maximum Input Signal CD, etc. Effect On, 1 kHz, 0.5% THD.. 2.0 V or more Frequency Response CD, etc. to Front L/R.. 10 Hz to 100 kHz, 3 dB Total Harmonic Distortion [U.S.A. and Canada models] (1 kHz, 45 W, Front L/R, 8 ).. 0.06% or less [Other models] (1 kHz, 50 W, Front L/R, 6 ).. 0.06% or less Signal to Noise Ratio (IHF-A Network) CD (200 mV) to Front L/R, Effect Off. 98 dB or more CD (250 mV) to Front L/R, Effect Off.. 100 dB or more Residual Noise (IHF-A Network) Front L/R... 150 V or less Channel Separation (1 kHz/10 kHz) CD, etc. (5.1 k shorted) to Front L/R.. 60 dB/45 dB or more Tone Control (Front L/R) BASS Boost/Cut.. 10 dB/100 Hz TREBLE Boost/Cut... 10 dB/20 kHz Headphone Jack Rated Output/Impedance. 400 mV/470 Input Sensitivity/Input Impedance CD, etc... 200 mV/47 k MULTI CH INPUT.. 200 mV/47 k Output Level/Output Impedance AUDIO OUT (REC).. 200 mV/1.2 k SUBWOOFER OUTPUT.. 4 V/1.2 k Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz) H.P.F. (FRONT SP, CENTER SP, SUR. L/R SP: SMALL/SML)..12 dB/oct. L.P.F. (Subwoofer)..24 dB/oct. Signal Level Composite... 1 Vp-p/75 Component. 1 Vp-p/75 (Y), 0.7 Vp-p/75 (PB/PR) Signal to Noise Ratio.. 50 dB or more Maximum Input Level.. 1.5 Vp-p or more Frequency Response (MONITOR OUT) Component Signal.. 5 Hz to 60 MHz, 3 dB

The following products are compatible with all standard SiriusConnect Home tuners that connect using the 8-pin DIN cable. Brand Accurian (Radio Shack) Colorado vNet Integra Integra Integra Integra Integra Integra Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Onkyo Philips Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Polk Audio RCA RCA Rotel Sony Sony Sony Sony Sony Sony Sony Sony Sunfire Sunfire Model AVR5048 DTC-9.8 DTR 5.8 DTR 6.8 DTR 7.8 DTR 8.8 TUN-3.7 HT-S5100 HT-SP904 HT-SP908 HT-SR800 T-4555 TX-NR905 TX-SR575 TX-SR605 TX-SR606 TX-SR705 TX-SR805 TX-SR875 HTS3545 SC-09TX HTS-LX70SW VSX-1017 VSX-1018AH VSX-817 VSX-818V VSX-90TXV VSX-917 VSX-918V VSX-91TXH VSX-92TXH VSX-94TXH X-Z9 SRH1000 RS2058 RTD260 RT1084 CMT-DH7BT CMT-HX7BT STR-DA3300ES STR-DA3400ES STR-DA4300ES STR-DA5300ES STR-DG2100 ZA-SAT1 TGP-401 TGR-401
Yamaha Yamaha Yamaha Yamaha Yamaha Yamaha Yamaha Yamaha Yamaha
DVX-700 HTR-6140 HTR-6150 HTR-6160 HTR-6180 RX-V463 RX-V563 RX-V663 RX-V863
The following distirbuted audio systems can control a Sirius tuner but require an RS232 connection from the SCH1P2 or SCH2P tuner kits. AMX Crestron NetStreams Xantech

updated: 6/18/08