s Rear Panel

@ [FUNCTION NORMAL MIX] Switch

(see page 8, 19)

Selects the mode that the MFC10 is to be operated in, Normal mode or Mix mode.

# [MIDI WX] Switch

Selects whether MIDI data is received via the WX jack or the MIDI IN jack.

$ [WX IN] Jack

A Yamaha Wind MIDI Controller WX7/11 can be directly connected to this jack. (The MFC10 supplies electric power to the WX7/11, so the BT-7 Power Box is not needed.)
% [MIDI IN/OUT] Jacks (see page 27)
Using a MIDI cable, external MIDI devices can be connect to the MFC10.
^ [FOOT CONTROLLER/SWITCH 2-5] Jacks

(see page 22)

MIDI WX FUNCTION NORMAL MIX
These jacks allow the connection of up to 4 optional foot controllers or foot switches to the MFC10. The connected foot controllers or foot switches can be used to control MIDI data in the same manner as the onboard foot controller.
& [DC IN] Jack (see page 3) 9 [1]-[0] Foot switch (see page 9, 12)
Selects Memory Numbers. Connect the power adaptor here to supply the MFC10 with power.
0 [x10] Foot switch (see page 9, 12)
Select the 100's or 10's digit.
* [POWER ON/OFF] Switch (see page 8)
Turns the MFC10s power on or off.
! Onboard Foot Controller (see page 22)
The Foot Controller can be used to transmit control changes, after touch, pitch bend, etc., to external MIDI devices.
User Memo Sticker The supplied User Memo Sticker can be applied next to the number plate above each foot switch to write memos on.

MFC10 Functions

When a foot switch is pressed, MIDI data (program changes/function data) stored in the MFC10s internal memory is transmitted to external MIDI devices.

Program Change Data

Program change data transmitted from the MFC10 can select voices, etc., on other MIDI devices. Bank select data can be transmitted along with program change data as well. The MFC10 can transmit the following function data to control other MIDI devices.

Function Data

NOTE ON/OFF (90-9F) CONTROL CHANGE (b0-bF) PROGRAM CHANGE (C0-CF) SONG SELECT (F3) START (FA)
CONTINUE (Fb) STOP (FC) SECTION CONTROL (F0) TEMPO CONTROL (Ft)
* Values in parentheses are shown in the display.

s 2 Modes...

The MFC10s foot switches can be set to operate in one of two modes (Normal Mode/Mix Mode). Use the [FUNCTION NORMAL MIX] switch on the rear panel to set the mode the MFC10 will operate in. (see page 5, 8, 19) How the foot switches operate in each mode is further explained below.

NORMAL mode

[In this mode, Program Change Memory and Function Memory are independent of each other.]

FUNCTION NORMAL MIX

Program change memory (128 types)
Function memory (100 types)
STATUS DATA/CTRL DEC 10 INC /NO /YES MEMORY EDIT FC EDIT WRITE /EXIT

Switch

Function lamp is off

Function lamp is lit

MIX mode
[In this mode, Program Change Memory and Function Memory are mixed.]
Upper level foot switches [6]-[0] Function memory (5 types)
Program change memory (5 x 5 types)
Lower level foot switches [1]-[5]
11 ~15 , 21 ~ 25 , 31 ~ 35 , 41 ~ 45 , 51 ~ 55
To access all 100 (F00-F99) Function Memory types, press the [FUNCTION] switch, and its lamp will light. In the MIX mode, Program Change memory (25 memories) is stored and played independent of Program Change memory in the NORMAL mode.
s Foot Controller Settings...
Sets parameters for the onboard Foot Controller and the external Foot Controllers 2-5. (see page 22)
s All Memory MIDI Channel Number Assign..
The settings for all MIDI channels, in all assigned memories, can be set to the same MIDI channel. (see page 24)

s Bulk Dump...

Internal data for the Normal mode Program Change Memory, the Mix mode Program Change Memory, and Function Memory and Foot Controller Memory (1-5) can be transmitted via MIDI OUT. (see page 25)

Normal Mode

Both Program Change Memory and Function Memory can be accessed in the Normal Mode. There are 128 memory allocations for Program Change data. By selecting a memory number, its stored program change is transmitted to external devices via the MIDI OUT terminal. There are 100 memory allocations for Function data (control change etc.). By selecting a memory number, its stored function data is transmitted to external devices via the MIDI OUT terminal.

Program Change Memory

Function Memory
Press the [FUNCTION] to switch between Program Change Memory and Function Memory.
Press the [POWER ON/OFF] switch on the rear panel to turn the power on.

POWER ON/ OFF

Set the [FUNCTION NORMALMIX] switch on the rear panel to the [NORMAL] position.
Press [FUNCTION] to switch between Program Change Memory (see page 9) and Function Memory (see page 12).
Program Change Memory (128 types)

Function lamp is off.

Function Memory (100 types)

Function lamp is lit.

If FUNCTION lamp is lit, press [FUNCTION], so that the lamp is off, and Program Change Memory is enabled. Program Change Memory transmits MIDI channel numbers 1-16 and program change data (001-128) that are stored in memory. There are 128 memory allocations in which Program Change data can be saved. Also, Bank Select data (00=MSB, 20=LSB) can be transmitted along with Program Change data.

Press [FUNCTION] to enable Function Memory (the FUNCTION lamp lights).
s Program Change Memory Control (Transmit)..
Program changes and bank select data are transmitted when a memory number is selected with the [1]-[0] and [x10] foot switches. A total of 128 (001-128) memory allocations are available for storing such data.

Select a Memory Number

[1]-[0], [x10] foot switches
To change or select the 1's digit. Press one of the [1]-[0] foot switches.

Example:

To change the current memory number 084 to 081 press [1] once.
To change and select both the 10's and 1's digits. Press [x10]. (The 10's digit of the LED flashes indicating input standby.) Press [1]-[0], to select the 10's digit value. (The 1's digit flashes indicating input standby.) Once again press [1]-[0] to select the 1's digit value.
To change the current Memory Number 023 to 082, press [x10], [8], and [2] in that order.
To change and select all digits. Press [x10] two times. If the 100's digit value is 1, it will change to 0, if it is 0 it will change to 1. (The 10's digit flashes indicating input standby.) Press [1]-[0], to select the 10's digit value. (The 1's digit flashes indicating input standby.) Once again, press [1]-[0] to select the 1's digit value.

Two times

To change the current Memory Number 048 to 126, press [x10], [X10], [2], [6] in that order.
When [x10] is pressed twice, the 100's digit value will alternate between 1 and 0. Attempting to select the number 000, will result in 001 being selected. Also, inputting any value above 128 will result in 128 being selected.
s Program Change Memory Edit...
The following 4 types of MIDI data can be transmitted with Program Change Memory.
The transmitting Channel Number and MIDI data can be stored to individual Memory Numbers.

STATUS

Cn (n=MIDI channel numbers 1-16) assigns the MIDI channel for voice selection. The number is shown in hexadecimal.
C0 C1 C2 C3 Channel 1 Channel 2 Channel 3 Channel 4 C4 C5 C6 C7 Channel 5 Channel 6 Channel 7 Channel 8 C8 C9 CA Cb Channel 9 Channel 10 Channel 11 Channel 12 CC Cd CE CF Channel 13 Channel 14 Channel 15 Channel 16

DATA/CTRL

Sets program numbers (voice numbers 001-128) for transmission. Refer to the owner's manual of the receiving device for details on voice assignments. Refer to a GM voice map for the 128 voice allocations of GM MIDI devices.

BANK MSB (Bank Select MSB) BANK LSB (Bank Select LSB)

oFF , 000 ~

Bank select numbers are used to access voices other than the 128 voices normally available in MIDI devices and GM devices. Program change data and bank select data (BANK MSB/ LSB:off, 000-127) must be transmitted together to access these voices. Refer to the owner's manual of the receiving device for specific information on bank select data.
The default settings for each memory (001-128) is as follows. STATUS=C0 (Channel Number 1), DATA/CTRL=001-128 (same as the memory number), BANK MSB/MAX=off, BANK LSB/MIN=off.

How to Edit Memory

If the FUNCTION lamp is lit, press [FUNCTION], so that the lamp is off, and Program Change Memory is enabled.
Select the Memory Number to be edited (see page 9). Press [MEMORY EDIT] to edit to begin editing that Memory Number. (The lamp above that foot switch and the STATUS lamp will flash.)
Press [MEMORY EDIT] to cycle through the 4 edit parameters (the selected parameters light will flash).
TOGGLE ON-OFF/NUMBER OF PGM can not be selected from Program Change Memory.
STATUS settings STATUS DATA/CONTROL settings DATA/CTRL BANK MSB/MAX BANK MSB settings BANK LSB settings BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM
Use [INC/YES] and [DEC/NO] to edit the parameter. Press [INC/YES] to increase the value shown in the LED display by 1, press [DEC/NO] to decrease the value by 1. By holding a button, values will continuously increase or decrease. Hold the [INC/YES] button and press the [DEC/NO] button and the value shown in the LED display will increase by 10. Repeatedly press [DEC/NO] to continue increasing the value by 10. Hold the [DEC/NO] button and press the [INC/YES] button and the value shown in the LED display will decrease by 10. Repeatedly press [INC/YES] to continue decreasing the value by 10.

Increase by 10

Decrease by 10
After the desired parameters have been edited in steps 2 and 3, press [WRITE/EXIT]. The Memory Number shown in the LED display will flash. (The flashing number indicates confirmation is necessary to proceed or cancel saving of the edited data.)

If data has not been edited, the Memory Number will not flash and the MFC10 will return to its normal control mode.
Press [INC/YES], to save the edited data to the current Memory Number, The MFC10 will return to its normal control mode. Press [DEC/NO] to cancel the save operation of the edited data. At this time the memory will revert to its pre-edited contents.
Another Memory Number from the same bank (10s digit bank) can be easily edited by pressing [1] - [0] without exiting from the edit mode. You must execute or cancel the save operation for the currently edited data (the current Memory Number will flash) before proceeding to edit the new number. Use [INC/YES] to execute or [DEC/NO] to cancel the save operation. If data has not been edited, the Memory Number will not flash and the newly selected Memory Number will be shown in the display.
Press [FUNCTION], the FUNCTION lamp will light, and Function Memory is enabled. Function Memory stores and transmits MIDI data such as note on/off, control change, program change, song select, start, continue, stop, etc., in its memory. There are 100 (F00-F99) memory allocations in which Function Data can be saved.
Press [FUNCTION] to enable to Program Change Memory. (The FUNCTION lamp is off.)
s Function Memory Control (Transmit)..
Function data is transmitted when a Memory Number is selected using the [1]-[0] and [x10] foot switches. A total of 100 (F00-F99) memory allocations are available for storing such data.
To change and select the 1's digit. Press one of the [1]-[0] foot switches.
To change the Memory Number F84 to F81 press the [1] foot switch once.
To change and select both the 10's and 1's digits. Press the [x10] foot switch. (The 10's digit of the LED flashes indicating input standby.) Press [1]-[0], to select the 10's digit value. (The 1's digit flashes indicating input standby.) Once again press [1]-[0] to select the 1's digit value.
To change the Memory Number F23 to F47, press [x10], [4], [7] in that order.

s Edit Function Memory..

The following 9 types of MIDI data can be transmitted with Function Memory.
Note On/Off (9) [STATUS=90-9F]
DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM
000-127 (Note Number) 001-127 (Note On Velocity) 001-127 (Note Off Velocity) Pn1-Pn4 (see page 18)
Transmits keyboard Note On/Off data. If a different note is set to each foot switch, the foot switches can be used to play a scale. Also, if a sampler is connected to the MFC10 the foot switches can be used to trigger samples.

C3. 71.

Note Number
Control Change (b) [STATUS=b0-bF]
000-127 (Control Number) 000-127 (Switch On Data) 000-127 (Switch Off Data) off, on, Pn1-Pn4 (see page 18)
Control Change List (for GM, XG supported devices)

Control Number 74

GENERAL
Function Bank Select Modulation Portamento Time Data Entry Main Volume Pan Pot Expression Bank Select Data Entry Hold 1 (Damper Pedal) Portamento Sostenuto (Chord Hold) Soft Pedal Harmonic Content Release Time Attack Time Brightness

Tempo Control (Ft) [STATUS=Ft]
DATA/CTRL 030~250 (Tempo Value)
The tempo of external devices can be controlled within a range of 30-250 beats per minute.
Select the Function Memory to be edited, press [MEMORY EDIT], to begin editing that memory number. (The lamp above the foot switch and the STATUS lamp will flash.)
Press [INC/YES] and [DEC/NO] to select the Status (transmit MIDI data and MIDI channel number) (the STATUS lamp will flash). The 1's digit (MIDI channel number 1-16) of Status is shown in hexadecimal. (see page 10)

Channel number

90.9F b0.bF CO.CF F3 FA Fb FC FO Ft
Transmit Note On/Off Transmit Control Change Transmit Program Change Transmit Song Select Transmit Start Transmit Continue Transmit Stop Transmit Section Control Transmit Tempo Control MIDI data
Press [MEMORY EDIT] to select the parameters set in the procedures above for editing (the lamp will flash).
Note On/Note Off STATUS (0-F indicates MIDI channel numbers) DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM 90-9F Note Number Note On Velocity Note Off Velocity Pn1-Pn4
Control Change b0-bF Control Number Switch On Data Switch Off Data Toggle On/Off Pn1-Pn4
Program Change C0-CF Program Number Bank MSB Bank LSB Pn1-Pn4

Song Select F3 0-127

Start FA

Continue Fb

Stop FC
Section Control F0 c01 - c42 Channel Number (if c41, c42 is used) Tempo Control Ft 030- 250
*() is displayed to indicate parameters that cannot be selected.
Press [INC/YES] or [DEC/NO] to edit parameter values.
Press [INC/YES] to increase the value shown in the LED display by 1, press [DEC/NO] to decrease the value by 1. By holding a button, values will continuously increase or decrease. Hold the [INC/YES] button and press the [DEC/NO] button and the value shown in the LED display will increase by 10. Repeatedly press [DEC/NO] to continue increasing the value by 10. Hold the [DEC/NO] button and press the [INC/YES] button and the value shown in the LED display will decrease by 10. Repeatedly press [INC/YES] to continue decreasing the value by 10.
After the desired parameters have been edited in steps 3 and 4, press [WRITE/EXIT]. The Memory Number shown in the LED display will flash.
Press [INC/YES], to save the edited data to the current Memory Number, The MFC10 will return to its normal control mode. Press [DEC/NO] to cancel the save operation of the edited data. At this time the memory will revert to its pre-edited condition.
Another Memory Number from the same bank (10s digit bank) can be easily edited by pressing [1] - [0] without exiting from the edit mode. You must execute or cancel the save operation for the currently edited data (the current Memory Number will flash) before proceeding to edit the new number. Use [INC/ YES] to execute or [DEC/NO] to cancel the save operation. If data has not been edited, the Memory Number will not flash and the newly selected Memory Number will be shown in the display.

11~15, 21~25, 31~35, 41~45, 51~55
Press [1]-[5] to access the 25 (5 x 5) Program Change Memories. To select the Program Change Memory numbers 10's digit, press [x10], next press [1]-[5] to enter a value of 1-5. Program Memory data can be edited in the same manner as the Normal mode, press [MEMORY EDIT] to begin editing.
Only 2 digits (10s digit and 1s digit) are displayed for Program Change memory numbers in the MIX mode.

s Editing MIX mode...

With the MFC10 in MIX mode control status, press the [MEMORY EDIT] button.
Editing Program Change Memory
To edit the data in the 25 memory types (independent in this mode) for foot switches [1] - [5], can be edited using the same procedure to edit Program Change Memory when in the Normal mode. (see page 10)

Editing Function Memory

To edit the data in the 5 memory types for foot switches [6] - [0], can be edited using the same procedure to edit Function Memory when in the Normal mode. (see page 13)
The MIX modes Function Memory
In the MIX mode, press [FUNCTION], the FUNCTION lamp lights, and the MFC10 is switched to the MIX modes function memory. It is also possible to select the Function memory numbers 10 value. Press [FUNCTION], the lamp turns off, and the MFC10 returns to the MIX mode.
Function Memory (5 types)
Function Memory (10 x 10 types)
STATUS DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM DEC 10 INC /NO /YES MEMORY EDIT
STATUS DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM DEC 10 INC /NO /YES MEMORY EDIT FC EDIT WRITE /EXIT

FC EDIT WRITE /EXIT

Program Change Memory (5 x 5 types)
Function Memory Control in the MIX mode
Function Memory Control in the MIX mode is the same operation as in the Normal Mode (see page 12).
Editing Function Memory in the MIX mode
Editing Function Memory in the MIX mode is the same operation as in the Normal Mode (see page 13).

Foot Controller

The MFC10s onboard foot controller (1) and external foot controllers (2-5) can be independently set to transmit MIDI data. Select the type of data to be transmitted by each foot controller and edit those parameters. Foot controllers can transmit Control Change, After Touch, and Pitch Bend data.
s Editing FC (Foot Controller) data..
Press [FC EDIT], one of the lamps above the [1]-[5] foot switches and the STATUS lamp will flash.
Press [1]-[5] to select the foot controller to be edited (the lamp above the selected foot switch will flash).
Onboard Foot Controller 1
External Foot Controller 3
External Foot Controller 5
External Foot Controller 2
External Foot Controller 4
Press [INC/YES] or [DEC/NO] to assign STATUS data (transmit MIDI STATUS and MIDI channel number)(the lamp will flash). The 1's digit (MIDI channel number 1-16) of Status is shown in hexadecimal. (see page 10)

q STATUS

Channel Number

b0 ~ d0 ~ E0 ~

bF dF EF

Transmit Control Change

MIDI STATUS

Transmit After Touch

Transmit Pitch Bend
Press [FC EDIT], to edit the selected data type (the lamp flashes) of the parameters set in the above procedure. It is possible to edit the following types of data. Control Change (b) [STATUS=b0-bF]
DATA/CTRL BANK MSB/MAX BANK LSB/MIN 001-031, 033-120 Control Number 000-127 MAX Value 000-127 MIN Value
After Touch (d) [STATUS=d0-dF]
DATA/CTRL BANK MSB/MAX BANK LSB/MIN 000-127 MAX Value 000-127 MIN Value
Pitch Bend (E) STATUS=E0-EF]
DATA/CTRL BANK MSB/MAX BANK LSB/MIN 000-127 Pitch Bend MAX 000-127 Pitch Bend MIN*
* The value of the Pitch Bends center pitch is 64.
Edit the parameters using the [INC/YES] or [DEC/NO] buttons.
After the desired parameters have been edited in steps 4 and 5, press [WRITE/EXIT]. The Foot Controllers number will flash in the LED display. Press [INC/YES] to execute the save operation or [DEC/NO] to cancel.
Another Memory Number can be easily edited by pressing [1]-[5] without exiting from the edit mode. You must execute or cancel the save operation for the currently edited data (the current Memory Number will flash) before proceeding to edit the new number. Use [INC/YES] to execute or [DEC/NO] to cancel the save operation. If data has not been edited, the Memory Number will not flash and the newly selected Memory Number will be shown in the display.

s About Foot Switch Use

Foot switches can also be connected to the [FOOT CONTROLLER/SWITCH 2-5] jacks located on the rear panel of the MFC10. If a foot switch is connected, the set BANK MSB/MAX value will be transmitted via MIDI when the foot switch is pressed. When the foot switch is released, the set BANK LSB/MIN value will be transmitted via MIDI.
All Memory MIDI Channel Assign
The MIDI channel settings for all assigned memories can be set to the same MIDI channel, setting all MIDI channels to the same channel can be convenient in some situations.

Pressing [INC/YES] in the operation will change all memory MIDI channel assignments!
For both Normal and MIX mode operation, simultaneously press both [MEMORY EDIT] and [FC EDIT]. The MIDI channel number will be shown in the LED display
Press [INC/YES] or [DEC/NO] to select the new channel number (C01-C16) for all memories.
Press [WRITE/EXIT]. The channel number in the LED display will flash.
Press [INC/YES] to confirm the setting of all channels, or [DEC/NO] to cancel the operation.

Bulk Dump

The MFC10s internal settings can be transmitted to an external MIDI data storage device. Using a device such a Yamahas MIDI Data Filer MDF2, the MFC10s data can be saved to, as well as loaded from such a device. The bulk dump operation is convenient for keeping important data.

(Transmission)

For both Normal and MIX mode operation, simultaneously press both [MEMORY EDIT] and [WRITE/EXIT].
Press the corresponding foot switch to select one of the 5 bulk dump types listed below. The selected bulk dump type will flash in the LED display.

Foot switch [1]

All data listed the 4 bulk dump types that follow will be transmitted.

Foot switch [2]

All data for Program Change Memory in the NORMAL mode will be transmitted.

Foot switch [3]

All data for Function Memory will be transmitted.

Foot switch [4]

Set data for the onboard Foot Controller 1 and External Foot Controllers 2-5 will be transmitted.

Foot switch [5]

All data for Program Change Memory in the MIX mode will be transmitted.
Press [INC/YES] and the selected data will be immediately transmitted via MIDI to the external device. Once the operation is complete, End will appear in the display, and the MFC10 will return to step 2. Press [WRITE/EXIT] to cancel the Bulk Dump operation.
Press [WRITE/EXIT] to return the MFC10 to normal control status.

(Receive)

In the normal control status or edit status, the MFC10 can receive bulk dump transmissions from an external device.
Make sure the [MIDI WX] switch on the rear panel is set to the MIDI position. Normal operation of the MFC10 is not possible during bulk dump operations.

Iiilz ntaie

The initialize operation restores the MFC10s settings to their original factory condition.
Using the initialize operation will erase whatever settings you have made on the MFC10. If you have important settings you wish to keep, store them to a MIDI data storage device with the Bulk Dump operation (see page 25)
Press [POWER ON/OFF] and switch off the power.
While holding both [MEMORY EDIT] and [FC EDIT], press [POWER ON/OFF] to switch on power to the MFC10.
FA will appear in the LED display once the initialize operation is completed. The MFC10 will return to normal control status.

Trouble Shooting

Problem Program changes do not transmit. Cause/Solution Check the mode, is it in NORMAL mode or MIX mode? (see page 6,7) Check the MAX and MIN setting. (see page 23) Is Program Change Memory active? TOGGLE ONOFF cannot be set in Program Change Memory. Also, TOGGLE ON-OFF can only be set in the Function Memorys control change. Check the [MIDIWX] switch on the rear panel. It should be set to the MIDI position.
Foot Controller data does not transmit.
Cannot set TOGGLE ON-OFF.
The MFC10 does not receive MIDI data and/or Bulk data.
MIDI Implementation Chart / MIDI-Implementierungstabelle / Table dimplmentation MIDI
[MIDI Foot Controller] Date:31-MAY-1996 Model MFC10 MIDI Implementation Chart Version : 1.00 +----------------------------------------------------------------------+ : : Transmitted : Recognized : Remarks : : Function. : : : : :-------------------+----------------+----------------+----------------: :Basic Default : 1-16 : 1-16 : memorized : :Channel Changed : 1-16 : 1-16 : : :-------------------+----------------+----------------+----------------: : Default : x : x : : :Mode Messages : o : OMNIon,OMNIoff : : : : : POLY,MONO : : :-------------------+----------------+----------------+----------------: :Note : 0-127 : 0-127 : : :Number : True voice: ************** : : : :-------------------+----------------+----------------+----------------: :Velocity Note ON : o 9nH,v=1-127 : o : : : Note OFF : o 8nH,v=1-127 : o : : :-------------------+----------------+----------------+----------------: :After Key's : x : o : : :Touch Ch's : o : o : : :-------------------+----------------+----------------+----------------: :Pitch Bender : o : o : : :-------------------+----------------+----------------+----------------: : 0-121 : o : o : : : : : : : : : : : : : : : : : : Control : : : : : : : : : : Change : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :-------------------+----------------+----------------+----------------: :Prog : o 0-127 : o 0-127 : : :Change : True # : : : : :-------------------+----------------+----------------+----------------: :System Exclusive : o : o : : :-------------------+----------------+----------------+----------------: :System : Song Pos. : x : o : : : : Song Sel. : o : o : : :Common : Tune : x : o : : :-------------------+----------------+----------------+----------------: :System :Clock : x : o : : :Real Time :Commands: o : o : : :-------------------+----------------+----------------+----------------: :Aux :Local ON/OFF : o : o : : : :All Notes OFF: x : x : : :Mes- :Active Sense : o : o : : :sages:Reset : x : o : : :-------------------+----------------+----------------+----------------: :Note : Received messages from MIDI IN are only bypassed : : : to MIDI OUT. : +-------------------+----------------+----------------+----------------+ Mode 1 : OMNI ON, POLY Mode 2 : OMNI ON, MONO o : Yes Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO x : No 31 YAMAHA

MIDI data format / MIDI-Datenformat / Format des dones MIDI

1 MIDI Receive/Send

1.1 Receive/Send conditions
<MIDI Receive conditions> Following MIDI data is transmitted via the MIDI OUT exception for FE.

1.2 Channel Message

1.2.1 Note On/Off
Following stored data in the Function memory can be transmitted by pressing the Foot Switch. data: Note On Note Off = $9n, 0-127, 1-127 = $8n, 0-127, 1-127
MIDI IN $8n (Note Off) $9n (Note On) $An (Poly Key Pressure/After Touch) $Bn (Control Change) $Cn (Program Change) $Dn (Chnnel Pressure/After Touch) $En (Pitch Bend) $F0 (System Exclusive) $F00 7A bb bb LM__0271PG (Program Change Memory Bulk) $F00 7A bb bb LM__0271FN (FUNCTION Memory Bulk) $F00 7A bb bb LM__0271FC (FC Memory Bulk) $F00 7A bb bb LM__0271AL (All Memory Bulk) $F00 7A bb bb LM__0271MX (MIX Program Change Bulk) $F1 (MIMI Time Code Quater Frame) $F2 (Song Position Pointer) $F3 (Song Select) $F6 (Tune Request) $F7 (EOX) $F8 (Timing Clock) $FA (Start) $FB (Continue) $FC (Stop) $FE (Active Sensing) $FF (System Reset)

<MIDI Transmit>

Received data is also transmitted via the MIDI OUT.

1.2.2 Control Change

Following data in the Function memory can be transmitted by pressing the Foot Switch or Foot Controller. data: Foot Switch Foot Controller =$Bn, 0-127, 0-127 =$Bn, 0-120, 0-127

1.2.3 Program Change

Stored data in the Program Change Memory or Function Memory (following data) can be transmitted by pressing Foot Switch or Foot Controller. data: Foot Switch Foot Controller =$Cn, 0-127 =$Cn, 0-120
1.2.4 After Touch.Pitch Bend
$8n (Note Off) $9n (Note On) $Bn (Control Change) $Cn (Program Change) $Dn (After Touch) $En (Pitch Bend) $F00 7A bb bb LM__0271PG (Program Change Memory Bulk) $F00 7A bb bb LM__0271FN (FUNCTION Memory Bulk) $F00 7A bb bb LM__0271FC (FC Memory Bulk) $F00 7A bb bb LM__0271AL (All Memory Bulk) $F00 7A bb bb LM__0271MX
Can be transmitted by using Foot Controller data: After Touch Pitch Bend =$Dn, 0-127 =$En, 0-127, 0-127

1.3 Exclusive

1.3.1 Section Control
Section control data (stored in the Function Memory) can be transmitted by using Foot Switch. Transmit data: F0, 43, 7E, 00, SS, DD, F7 SS: Section Number 00-27 [Hex] DD: ON/OFF (ON=7F, OFF=00) Received data is also transmitted via the MIDI OUT.
(MIX Program Change Bulk) $F7E 00 ss dd (Section Control) $F6n 7A (Reset Start) $F6n 7D (Stop & Rewind) $F7E 01 t4 t3 t2 t1 (Tempo Control) $F7 (EOX) $FA (Start) $FB (Continue) $FC (Stop) $FE (Active Sensing) MIDI OUT 32

1.3.2 Start/Stop Control

Start/Stop control data (stored in the Function Memory) can be transmitted by using Foot Switch. data: Reset Start Stop & Rewind =F0, 43, 6n, 7A, F7 =F0, 43, 6n, 7D, F7

16 : : 0bbbbbbb 0bbbbbbb 00000000 : 00000000 0ddddddd : 0sssssss 11110111 F00= DeviceNumber(Fixed) 7A BB= Byte Count BB 4C(asciiL) 4D(asciiM) 20(ascii ) 20(ascii ) 30(ascii0) 32(ascii2) 37(ascii7) 31(ascii1) 4D(asciiM) 58(asciiX) 00 : 00 DD= Data : SS= Check Sum F7
Overwrites to the Function memory when data is received.
2.4 Foot Controller memory data bulk dump
01111010 0bbbbbbb 0bbbbbbb F00= Device Number(Fixed) 7A BB= Byte Count BB 4C(asciiL) 4D(asciiM)
Operation Guide / Bedienungsfhrer / Guide des oprations
NORMAL mode Program Chamge Memory
MIX mode Function Memory + Program Chanege Memory

Others

All memory MIDI channel Assign

Bulk Dunp

MEMORY EDIT WRITE /EXIT

Initia Lize

Program Table / Programmbersicht / Tableau de programmes

NORMAL mode

DATA: NAME: qProgram Change Program Number:
6 STATUS DATA/CTRL BANK MSB BANK LSB
1 STATUS DATA/CTRL BANK MSB BANK LSB
qFunction Function Number: F
6 NUMBER OF PGM STATUS DATA/CTRL MAX MIN TOGGLE ON-OFF 1 2
1 NUMBER OF PGM STATUS DATA/CTRL MAX MIN TOGGLE ON-OFF 1 2

qFoot Controller

1 STATUS DATA/CTRL MAX MIN 4 5

MIX mode

DATA: NAME:

Function Number: F

6 NUMBER OF PGM STATUS DATA/CTRL MAX MIN TOGGLE ON-OFF 3

Program Number:

* Make copies of sheet to keep records of your MFC10 settings. * Machen Sie sich zum Eintragen der MFC10-Einstellungen Kopien von diesem Blatt. * Faites des copies de ces feuilles pour conserver les rglages de votre MFC10.
Specifications / Technische Daten / Spcifications
Program Change Memory Function Memory Mode Foot Controllers1 (Onboard Foot Controller) Other
Normal:128, Mix:Normal, Mix 2-5 (External Foot Controllers)
MIDI IN -> MIDI OUT (MERGE Transmit) WX11 etc., Controller Connection MIDI Bulk Dump (Transmit and Receive) Foot Switch x12, Onboard Foot Controller x1, Panel Switch x5, LED Display, Power Switch, MIDI IN/WX IN Switch, Function Normal/Mix Switch Foot Controller Jacks x4, MIDI IN/OUT Terminals, WX IN Terminal, DC IN Jack Owner's Manual, User Memo Sticker 608 (23-15/16") x 215 (8-1/2") x 153 (6") 3.52 (7Ibs 12oz)