INSTALLATION GUIDE

ZE-NC524 Software Update
Preparation: I Carefully read the entire installation guide and keep it nearby for reference I The update preparations are described in a separate preparations for update guide (recommended read for first-time updaters) Important information: I Do not disconnect the device from the power supply during transfer communication of the updates. Also make sure that it doesnt get coincidentally disconnected. I Its mandatory to closely follow this installation guide step-by-step. Even a small deviation may render your device permanently unusable. I Do not unplug your USB data carrier during the update process. I Do not use any updates which are not expressively certified for your ZE-NC524 (i.e. no updates from similar models). If you deviate from these step-by-step instructions, you will void your warranty and risk to damage your device. In that case ZENEC will not take any responsibility. Installation of the firmware updates: The update software consists of three parts on three sticks i.e. MPEG, BT, MCU. Make absolutely sure that you install all software parts following the below mentioned installation sequence: 1. MPEG 2. BT 3. MCU
Caution: Ensure your cell phone is switched off during the entire update process any Bluetooth activities, as Bluetooth coupled phones receiving incoming calls, are prone to fatally interrupt the update process. 1. a. b. c. d. e. f. 2. a. b. c. d. e. f. g. Installation Part -> MPEG Plug in the first USB data carrier labelled MPEG into the running ZE-NC524. The update will start automatically. Progress is numerically displayed. Do neither switch off the ZE-NC524 nor unplug the USB stick during the update. This update is finished as soon as the ZENEC logo is displayed. Now switch off the ZE-NC524. Remove that USB-stick and continue with part two. Installation Part 2 -> Bluetooth 3.60 Plug in the USB data carrier labelled "BT into the switched off ZE-NC524. Now switch on your device. The update starts automatically now. Progress will be displayed numerically. Neither switch off the ZE-NC524 nor unplug the USB stick during the update. Wait until the process has finished. The device will then switch off by itself. Remove the USB stick from the device. Switch your ZE-MC294 on again and continue with part three.
3. Installation Part 3 -> MCU a. Plug in the USB data carrier labelled MCU into the running ZE-NC524. b. The update will start automatically. Progress is numerically displayed.

1 of 2 22nd of July, AL

W W W. Z E N E C. C O M

c. d. e. f.

Do neither switch off the ZE-NC524 nor unplug the USB stick during the update. Wait until the process has finished. The device will then switch off by itsel. Remove the USB stick from the device. Switch on your device again and continue with part 4.
4. Check version After you applied all three software updates you need to perform a version check. BT Version Check BT version with: Bluetooth> Setup >Seite2 > Version Bluetooth software check after a successful update should say: HW100-SW360 MCU and MPEG Version In order to check the MCU and MPEG versions you need the remote control. Follow these steps: 1. Insert a CD or DVD 2. Type the following keys using the remote control: a) b) c) d) e) f) g) h) i) 2X 1X 1X 1X 1X 1X 1X 1X 1X [STOP] [+] [UP] [+] [DOWN] [+] [LEFT] [+] [RIGHT]

Only version numbers of the MCU, MPEG (marked as DN) are of interest. After a successful update the software version screen should say: DN (i.e. MPEG) : 2.06 MCU : 2.08 If any deviation from the above mentioned status should occur, you can fix it by reapplying the respective part of the software. After doing so, reassure yourself by repeating the version check until you get the desired result. CAUTION : If one or even more of the partial updates fail, you may encounter strange erratic behaviour of your unit. Therefore version check and, in case of version check failure, reinstallation of the respective firmware parts are absolutely mandatory. Note: Password User who have altered the default password, need to type in 012345 as the unit resets to factory defaults during the update.

2 of 2 22nd of July, AL

How to update navigation software and maps on your ZE-NC524
Purpose: Update of navigation software and maps after initial startup of a newly bought ZENEC device. First time update of map data is included at no extra costs. Note: The online update should be conducted within 30 days after initial startup, cause the device has marked this date and will remember it. Any update after this time period will be subject to a charge. Please read this guide entirely before you start the update procedure.
Mandatory prerequisites: 1. You need to get registered on www.naviextras.com. Write down your username and password as you will subsequently need it to log on. 2. ZENEC device is properly installed, SD-card is inserted and has succesfully been used to navigate (at least once). 3. Free of charge synchronizing toolbox has been downloaded from https://zenec.naviextras.com/shop/ portal/downloads and has also been successfully installed. 4. Your PC has an active broadband internet connection with a download rate of at least 1 MBit/s. 5. PC features an SD- card reader and the ZENEC SD card, with the navigation software and the maps, has been inserted. Optional prerequisites: In case you would exactly like to know which map has been updated to which version, write down the version info of the map(s). To get it displayed tap on Navi->Settings->About->Maps. Step by step: 1. Open Toolbox-Software. 2. Log on with your user access data. 3. Click My updates. 4. Choose Install. 5. Now the program offers you to perform a backup. You should accept, cause the program is going to backup the entire card contents including the license key. 6. Follow the on-screen instructions to install the available updates. 7. Do not interrupt the download or installation process, otherwise you need to repeat the entire procedure. Duration of the update process will be something in between 15 minutes and (if unlucky) a couple of hours, depending on server load and transmission speed. 8. After finishing the installation, close the toolbox program. Remove the SD card and insert it into your ZENEC device. 9. Now you may check whether your update has been successfull. Tap on Navi-> Settings -> About -> Maps and browse through the available country maps. The relevant date of the respective map will be displayed on-screen. Done.

Page 1 of 2

Publ. 10/2010 AL/JL

Page 2 of 2