Model 750X

Model 500X

500X & 750X

Users Guide Gua del Usuario Mode demploi

Thank you

.for purchasing a Drill Doctor. It is sure to become a valuable tool because you will always have sharp drill bits before a project, during a project, and after a project. As president of this company, I am very proud of the quality of our productsand I am equally proud of the great people at Drill Doctor who design and produce them. If you have questions or need help with your Drill Doctor, please contact us and one of our customer representatives will be there to help. We support what we build! Use this Users Guide and the DVD video to learn to operate your Drill Doctor quickly and easily. Id also like to invite you to visit our website at www.DrillDoctor.com. There you will find:

Contents

English...1 Important Safety Instructions..2 Getting to Know Your Drill Doctor..5 Identifying Basic Drill Bits..6 Anatomy of a Drill Bit..6 The Drill Doctor Sharpening Process..7 Choosing Your Drill Bit Point Angle on the Model 500X..7 Model 750X..8 Aligning the Drill Bit..8 Sharpening the Drill Bit..10 Identifying Correctly Sharpened Drill Bits.12 Split Points..13 Creating or Replacing a Split Point..14 Identifying Correctly Split Bits.15 Grit Tube Attachment...16 Sharpening Bits of Different Lengths, Diameters and Types Large Drill Bits..16 Short Drill Bits and Bits Smaller than 1/8".17

English

Demonstrations of all operations with the sights and sounds leading to successful drill bit sharpening Downloadable copies of the Users Guide Warranty registration Service and contact numbers Again, thank you for buying a Drill Doctor. Now go enjoy its convenience and quality.
Hank ODougherty President, Drill Doctor
Masonry Drill Bits..17 Using the Variable Alignment to Adjust Chisel and Relief Angle..19 Using the Variable Material Take-Off on the 750X.20 Questions and Answers..21 Drill Doctor Maintenance..24 Accessories and User-Replaceable Parts..27 Warranty...28 Espaol..29 Franais..60

www.drilldoctor.com

IMPORTANT SAFETY INSTRUCTIONS
For your own safety, please read this Users Guide before operating the Drill Doctor.
DRESS PROPERLY. Do not wear loose clothing or jewelry; they can be caught in moving parts. Wear protective hair covering to contain long hair. USE PROTECTIVE EQUIPMENT. Use safety glasses. Use face or dust mask if working operations create dust. DO NOT ABUSE THE CORD. Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges. MAINTAIN TOOL WITH CARE. Keep the Drill Doctor clean for best and safest performance. Follow instructions for maintenance and changing accessories. Inspect cords periodically and if damaged have them repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep unit dry, clean and free from oil and grease. DISCONNECT TOOLS. Always disconnect the Drill Doctor when cleaning, inspecting, and changing accessories, such as the diamond sharpening wheel. When not in use, disconnect from the power supply. Never touch internal parts of the sharpener when it is turned on or plugged in. The rotating diamond wheel can cause injury. AVOID UNINTENTIONAL STARTING. Make sure switch is in the OFF position before plugging in. STAY ALERT. Watch what you are doing, use common sense and do not operate the tool when you are tired. CHECK DAMAGED PARTS. Before use of the tool, it should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in the instruction manual. Have defective switches replaced by an authorized service center. Do not use the tool if the switch does not turn it on and off. Do not use if the grinding wheel is damaged. Use only grinding wheels recommended by Drill Doctor.

Installation

Carefully unpack the Drill Doctor drill bit sharpener and set it on a table. Check to see that no damage has occurred in shipment. Check all packing material to be sure that all parts are present. See Users Guide for part identification diagram. The unit is completely assembled; the Drill Doctor only needs to be placed on a flat stable tabletop. Connect to properly wired outlet.

Precautions

When using electric tools, basic safety precautions should always be followed to prevent the risk of fire, electric shock, and personal injury. KEEP WORK AREA CLEAN. Cluttered areas and bench invite accidents. DO NOT USE IN DANGEROUS ENVIRONMENT. Do not use in damp or wet locations, avoid exposure to rain. Keep work area well lit. Do not use tools in the presence of flammable liquids or gases. GUARD AGAINST ELECTRIC SHOCK. Avoid body contact with earthed or grounded surfaces (e.g., pipes, radiators, ranges, refrigerators). KEEP OTHER PERSONS AWAY. Do not let persons, especially children, not involved in the work touch the tool or the extension cord and keep them away from the work area. STORE IDLE TOOLS. When not in use, tools should be stored in a dry, locked-up place out of the reach of children. DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was intended.
WARNING. The use of any accessory or attachment other than one recommended in the instruction manual may present a risk of personal injury. HAVE YOUR TOOL REPAIRED BY A QUALIFIED PERSON. This electric tool complies with the relevant safety rules. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user. NEVER LEAVE TOOL RUNNING UNATTENDED. USE EAR PROTECTION DURING USE. The Drill Doctor can generate up to 85 dB (A) noise emissions when in operation. For Service Contact: Professional Tool 210 E. Hersey St. Ashland, OR 97520 USA Phone: 1-888-MYDRILL (693-7455) FAX: 541-552-1377 Email: tech@drillDoctor.com

Getting to Know Your Drill Doctor
Watch the User DVD included with your Drill Doctor and become a sharpening expert in minutes!
Drill Stop Bit Clamp Arms
Relief Angle Settings Alignment Port
Power Switch and Cord Alignment Button
Cam Guide Sharpening Port Point Angle Adjustment Plate

On 750X MTO is here

Splitting Guide Wheel Access Cover Quick Change Diamond Sharpening Wheel (Inside) Chuck Jaws Point Angle Adjustment Knob Split Point Port Split Point Guide Rails
Masonry Bit Alignment Mark Alignment Guides Sharpening Guides Adjustable Material Take-Off (MTO) Knob (750X Only)
WARNING: Some dust created by power sanding, grinding, miscellaneous construction activities, as well as contents from the machine including the molding, wiring, grinding wheel, or any other parts may contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm and can be hazardous to your health.

Cam Chuck Knob

www.drilldoctor.com www.drilldoctor.com

Grit Tube

Identifying Basic Drill Bits
The Drill Doctor is most efficient when used to sharpen a drill bits original point angle. With its standard Diamond Sharpening Wheel it will sharpen high-speed steel, cobalt, TiN-coated, carbide and masonry drill bits. It has been designed and engineered to sharpen three of the most common drill bit types and offer you an ability to customize your point:
The Drill Doctor Sharpening Process
The sharpening process includes 4 easy procedures: 1. Determine the type and angle of the drill bit. 2. Align the bit in the Chuck. 3. Sharpen the bit. 4. Split the point (if you choose). Be sure to complete the first three procedures in order to sharpen a bit; and always sharpen a bit prior to splitting it.

Standard Point

This general-purpose point is used for drilling softer materials like cold rolled steel, aluminum, and wood.
Choosing Your Drill Bit Point Angle
When drilling into certain difficult materials, a shallower point or 135 point angle produces a better-finished hole. Your Drill Doctor allows you to sharpen bits with either the standard 118or the flatter 135 point angle. You can also adjust the chisel and relief angle. (Refer to page 19 for the benefits of using Variable Alignment to adjust the Chisel and Relief angles.) Depending on the material you are drilling in, you may choose to increase or decrease these angles.

Split Point

Split-point bits are self-centering and are generally used for tempered steels, hard alloys or hard cast materials.

Masonry Bits

Masonry bits have a carbide insert at the point and are used for drilling materials like cement, brick, and ceramic.

On the Model 500X

Anatomy of a Drill Bit

Chisel Edge Cutting Edge

Check your drill bit angle
It is important to understand that each bit has a all of these characteristics. When viewing a well-sharpened bit from the end, the entire surface from the Cutting Edge to the Heel will have a finely ground surface without ridges or indentations. The Heel will always be lower than the Cutting Edge. www.drilldoctor.com

Relief Angle

Cutting Edge
Most bits are 118 or 135. Hold your bit point up to the key to the left to see which type your bit looks like. If you cant tell due to small size or damage on the tip, set your Drill Doctor based on the application. Most wood and soft metal applications should use 118 degree. Harder materials such as stainless steel and tool steel should use 135 or if you are drilling contoured materials such a car fender and plan on splitting the point.
Point Angle Adjustment Knob

Choose the angle

Loosen the Point Angle Adjustment Knob on the right side of the Sharpening Port and slide the metal Point Angle Adjustment Plate to either the standard 118 or the flatter 135 point angle. Then re-tighten the Knob.
Insert bit in Chuck and tighten
Insert the bit into the Chuck Jaws and close the Jaws just to the point where the bit slides in and out. Do not over tighten the Chuck; the bit needs to be able to move in and out until Step 4. (Model 750X users refer to Using the Variable Material Take-Off (MTO) on page 20.) A good test to see if the Chuck is tightened the correct amount is to make sure it moves when you pull on it with your fingers, but will not fall out when you turn the Chuck upside down.

On the Model 750X

The Model 750X has additional advanced features that enable you to fine-tune your bit geometry. Loosen the Point Angle Adjustment Knob to the right of the Sharpening Port and slide the metal Point Angle Adjustment Plate to 118, 135 or the custom angle of your choice. Choose your point angle based on the application youre drilling. Then re-tighten the Knob.

Alignment Button

Insert Chuck into Alignment Port

Aligning the Drill Bit

This makes sure that the Drill Doctor creates the right geometry. And, it sets the bit so that only a small amount of the tip is taken off. See page 17 to align and sharpen a Masonry drill bit.)
Press the Alignment Button down and hold it. Match the either of the Alignment Guides on the Chuck with the 118 Notch on the Alignment Port. Insert the Chuck. While holding the button down, slide the drill bit Drill Bit 118 forward until it touches Alignment Stop Guide the Drill Stop and the Chuck is pushed all the way into the Alignment Port. Release the Alignment Button. If you are using a Model 750X and have chosen a custom bit point (between 115 and 140), start your alignment in the closest setting to the point angle you are using. (For example, if you are setting the point angle below 118, than set the alignment in the 118 setting.) Refer to Using the Variable Alignment to Adjust the Chisel and Relief Angle on page 19. www.drilldoctor.com

Adjust Bit Position

Look at your bit and make sure the Clamp Arms are in the bits narrowest spot. If they arent, turn the bit in the chuck so that it is held by the Bit Clamp Arms at the narrowest width. This is important because this setting determines the angle at which your bit will be sharpened.
Drill Bit Stop Bit Clamp Arms
You will hear a grinding noise (zzzzzzzzz) as you complete each half-turn and each side of the bit face is ground. The Chuck will rock as you turn it and the Cam rides on the Guide.

Align Guides

Turn the Drill Doctor on. Align either of the Sharpening Guides with the Cam Guide on the machine.

Cam Sharpening Guide

Tighten Chuck
Hold onto the Chuck and tighten the Chuck Knob. (Avoid over-tightening the Chuck in the Alignment Port. This could damage the Chuck and Port.)

Cam Guide

Against Cam Guide
Insert Chuck and turn until the bit is sharp

Remove and re-tighten

Press the Alignment Button and remove the chucked drill bit. Tighten the Chuck once more to ensure the bit wont move when you sharpen it. You are now ready to sharpen the drill bit.

Sharpening the Drill Bit

Before sharpening you should know: Keep the Cam in contact with the Cam Guide as you sharpenpush the Chuck straight into the Port. Only light pressure is required.
Insert the Chuck in the Sharpening Port. Making sure you keep the Cam against the Cam Guide, rotate the Chuck one halfturn in a clockwise directionfrom Sharpening Guide to Sharpening Guidean even number of times. Your motion should be smooth and even. To sharpen both sides of the bit evenly, always use an even number of half-turns. The number of turns needed to sharpen the bit depends on the size. Turn the Chuck an even number of half-turns with light inward pressure: 3/32-inch bitsuse 2 to 4 half-turns, 1/8-inch bitsuse 4 to 6 half-turns, 3/8-inch bitsuse 16 to 20 half-turns. Note: Use just enough pressure to keep the Cam against the Cam Guide. Let the machine do the sharpening. www.drilldoctor.com
Identifying Correctly Sharpened Drill Bits (and what to do with those that arent!)

Correctly Sharpened Bits

Heel Chisel Point

Problem

Insuffecient (Negative) relief or a slow cutting drill bit. Cutting Edge Heel

Sharpening Bits of Different Lengths, Diameters, and Types
Drill Bits Of Different Sizes
Too many rotations of a small-diameter bit may result in incorrect sharpening and too few on a large bit may not sharpen enough. Continue to sharpen until the Chisel Edge is clean and straight and the entire surface from the Cutting Edges to the Heel is finely ground. 3/32-inch bitsuse 2 to 4 half-turns, 1/8-inch bitsuse 4 to 6 half-turns, 3/8-inch bitsuse 16 to 20 half-turns.
Aligning and Sharpening Masonry Drill Bits
To sharpen a masonry bit, you do not turn the Chuck. Instead you insert the Chuck until it touches the wheel, remove, and repeat on the other side.

Large Drill Bits

The Model 500X sharpens bits from 3/32 to 1/2. (You can also purchase a Large Bit Chuck that sharpens bits up to 3/4.) The Model 750X comes equipped with that Large-Bit Chuck. It sharpens bits from 3/32 to 3/4 inches. Large bits are sharpened just like any other bit. It is important to sharpen these bits so that the entire face of the drill bit is sharpened. A large bit requires more pressure and will require more half-turns to sharpen it.
Set the point angle to 118.

2. Carbide Insert

Align the bit with the Masonry Sharpening Marks
Insert the bit into the Chuck and line up the carbide insert on the tip of the bit so that it is parallel to the Masonry Sharpening Marks on the end of the chuck. Leave about 1/2-5/8 of bit sticking out past the nose of the chuck. Tighten the chuck just to the point that the bit slides in and out.
Using the Variable Alignment to Adjust the Chisel and Relief Angles
Both Models 500X and 750X enable you to adjust the Chisel and Relief Angles of your drill bit. The Chisel and Relief Angles have a direct effect on the performance of your drill. By increasing the Relief Angle, you can increase the speed of the drill in softer materials. To improve the quality of the hole you can adjust the drill to be less aggressive. A less-aggressive drill has a lower Chisel and Relief Angle. Your Drill Doctor enables you to adjust both angles in one setting.

Masonry Sharpening Marks

Set the depth
Set the depth by lining up the Sharpening Guide with the Cam Guide. Push the Chuck into the Sharpening Port until it stops and tighten the Chuck. Remove the Chuck to ensure the carbide insert is aligned with the Masonry Sharpening Marks and tighten again.
Sharpening Guide Cam Guide

Chuck bit as usual

To prepare your bit for this fine adjustment, follow all the Steps for chucking your bit given previously in this Users Guide.

To adjust the Chisel and Relief Angles, simply align the bit as usual with the following adjustment;

Sharpen by plunging

Line up the Sharpening Guide on the Chuck with the Cam Guide on the machine. Plunge Cam the Chuck into the Sharpening Port until it touches the Sharpening Wheel. Remove the Chuck, rotate one half-turn clockwise and repeat the plunge action. Start with four plunges and always use an even number. Inspect the bit and continue until the cutting surfaces are sharp. If the bit stops grinding before the edges are sharp, loosen the Chuck, push the bit out slightly. Make sure carbide insert is still aligned with Masonry Sharpening Marks. Tighten the Chuck, and continue sharpening. www.drilldoctor.com

Alignment Port + 118

To increase Reliefposition the Chuck in the Alignment Port so that the Alignment Guide is closer to the (+) position. This will make a more aggressive drill point.
To decrease Chisel and Reliefposition the Chuck in the Alignment Port so that the Alignment Guide is closer to the (-) position. This will make a more precise hole. Take care not to adjust Relief too far as this will actually cause the drill to lose all Relief and therefore not drill a hole. Each notch in the Alignment Port is approximately a 10 change in Chisel Angle. www.drilldoctor.com
Adjust bit position, tighten Chuck, and sharpen as usual
Refer to pages 9-10 for these Steps. Experiment with a few different settings to find the one that best suits your drill bits and application. You may find it helpful to mark this setting for future use.

Questions and Answers

1. Question:
Why was my drill bit sharpened improperly?

Answer:

The most common cause of improper sharpening is drill bit alignment. Key causes are: 1. Chuck not pushed all the way into the Alignment Port. 2. Drill not aligned in the Chuck Jaws correctly. 3. The type of drill requires an angle adjustment to achieve the desired Chisel and Relief Angles. Try using the Variable Alignment to adjust the Chisel and Relief Angle (see page 19). 4. Chuck is dirty or the bit slipped out of alignment. See pg 25, Cleaning the Chuck. 5. Too many rotations of a small-diameter bit results in incorrect sharpening, and too few on a large bit may not sharpen enough. See page 16, Drill Bits of Different Sizes.

Using the Variable Material Take-Off (MTO)
The Model 750X enables you to remove more or less material from the tip of your bit when you sharpen. If your bit is only slightly dull and you simply wish to touch up its point, turn the Material Take-Off Knob clockwise to reduce the amount of time it takes to sharpen the bit. If your drill bit is quite dull or damaged, turn the Material Take-Off Knob counter-clockwise to increase the amount of material removed. Your MTO adjusts from 0 to.040 of an inch in increments of.005. Prior to aligning the bit, turn the MTO Knob counter-clockwise until it stops. (This is the maximum material that can be removed in one sharpening.) Then turn it clockwise 3 marks on the MTO knob. This is a good place to start for most bits. Now turn the MTO knob either direction to adjust the desired MTO. Each mark on the MTO knob is equal to.005 change in material removed from the bit. Note: After you have sharpened your bits on the Drill Doctor at least one time, it is desirable to turn the MTO Knob such that only a small amount of material is removed from the bit each time you sharpen. This will significantly decrease the time to sharpen as well as extend your bit and wheel life. Once youve made your adjustment, align and sharpen your bit as usual.
Variable Material Take-Off Knob

2. Question:

When I aligned the drill bit and sharpened it, why was no material removed?
This happens when the bit is not protruding out of the Chuck far enough. You may have allowed the Alignment Button to knock the drill back into the Chuck when aligning the bit. Carefully realign the bit in the Alignment Port again. Make sure the drill bit is pushed all the way against the Drill Stop before you release the Alignment Button

3. Question:

I sharpened the bit. Why will it not cut?
This happens when the Heel on the bit is higher than the Cutting Edge (negative relief). To correct this problem, follow the instructions in Using the Variable Alignment to Adjust the Chisel and Relief Angle on page 19. You may have a specialty drill bit. Slow and Fast Spiral, Helix, Turbo Flutes, and Raised Margin drill bits are considered specialty bits. If youre are getting insufficient relief on specialty bit types, try aligning all the way in the (+) setting on the alignment port. This will help improve the sharpening on these types of bits.

6. Question:

Why is the chisel edge on my drill bit flat?
During the alignment process the Bit Clamps were gripping the high points of the drill bit. Realign the drill bit making sure that the Bit Clamps are located in the narrowest section of the bit. See page 10.

7. Question:

4. Question:
What can I do about flat spots on the bit point between the Cutting Edge and the Heel?
The most common cause of improper sharpening is improper drill bit alignment. Key causes are: 1. Drill point not pushed all the way to the Drill Stop. 2. Chuck not pushed all the way into the Alignment Port. 3. Drill not aligned in the Bit Clamps correctly. In order to correct these problems be sure the Chuck is all the way in the Alignment Port. The drill point must be against the Drill Stop and the Bit Clamps must be at the narrowest part of the drill bit.
The flat spots on a sharpened bit are the result of an incomplete or paused half-turn of the Chuck in the Sharpening Port. To correct, apply light, inward pressure and rotate the Chuck smoothly while sharpening. Be sure to complete the half-turns.

5. Question:

Why is the drill point off center?
If the tip of the drill bit appears to be sharpened off center, check the following items: You may not have done an even number of half-turns when you sharpened and one face of the bit was ground more than the other. Always use an even number of half-turns when you sharpen. Make sure that there are no particles between the Chuck Jaws and the drill bit that could hold it off center. Check the drill to ensure it is straight and free of burrs. Make sure the bit is not loose in the Chuck. During the sharpening process be sure to keep the same pressure on each half-turn.

8. Question:

Why is my split point uneven?
Page 15 shows a drill point that is undersplit and a drill point that is correctly split. To correct an uneven point split, insert the Chuck into the Splitting Port and split both sides again. Push the Chuck into the Port until it stops. Repeat until the split sides are equal and look like the correctly split bit shown above.

9. Question:

Why does the drill bit back up into the Chuck during the sharpening procedure?
Cleaning Your Drill Doctor
With the Drill Doctor unplugged, shake accumulated drill bit grinding dust from behind the Wheel Cover into a disposable container. Remove dust particles around the wheel with a small, dry brush. Dispose of the container and drill bit dust in a safe and environmentally approved manner. With a dry cloth wipe the inside and outside of the Sharpening Port to remove any grinding dust that may have accumulated. A standard 1" vacuum hose works equally well. You can also use the Grit Tube attachment as shown on page 16.

Make sure the bit is tight in the Chuck before sharpening. Your Chuck may be dirty. Follow the steps for cleaning the Chuck on page 25.

10. Question:

When splitting, why dont I hear a grinding sound?
The Chuck is not seated properly in the Splitting Port. The Chucks Sharpening Guide must line up with the Splitting Guide on the top of the Split Point Port. Firmly and slowly push the Chuck into the hole until the grinding sound stops.

Cleaning the Chuck

With compressed air, blow out the Chuck from the Knob end or brush out with a small, dry brush.

11. Question:

Can I change a 135 drill bit into a 118 drill bit?
Determining if Replacing the Diamond Sharpening Wheel is Required
You can double the life of the Diamond Sharpening Wheel by reversing it before you replace it. The Sharpening Wheel supplied with the Drill Doctor is designed to give you long and trouble free service, with an average of more than 200 sharpenings for 3/32" to 1/2" drill bits. The Diamond Sharpening Wheel may need to be changed if: Sharpened drill bits burn or turn blue no matter how fast or slow you rotate the Chuck. When touching the Sharpening Wheel (with the machine unplugged), the lower portion feels too smooth (nonabrasive). When sharpening the drill bit, it takes too many halfturns to sharpen. Contact the store or dealer where you purchased the Drill Doctor, or contact Drill Doctor directly, to purchase a replacement Sharpening Wheel.
You can change the degree angle of any drill bit from 135 to 118. The alignment and sharpening procedure will need to be performed three or more times to remove the old angle and produce the new angle desired.

Drill Doctor Maintenance

After sharpening 20 to 25 drill bits, the drill bit grinding dust will accumulate in the grinding compartment. Grinding particles will promote wear in the Sharpening Port and Chuck, so cleaning on a consistent basis can add life to your machine. Before any maintenance or cleaning is performed, be sure to disconnect your Drill Doctor.
Removing the Wheel Access Cover
With the Drill Doctor unplugged, use your nail or the tip of your finger to pull the Wheel Access Cover down. It will come completely off for easy access. To close, insert the Cover in the slots and snap it back into place.
Reversing or Replacing Your Diamond Sharpening Wheel

Accessories

Order accessories through our website: www.DrillDoctor.com, or by contacting us at the phone number listed on the Warranty page (page 28), or at the retailer where you purchased your Drill Doctor.

Unplug your Drill Doctor, make sure machine is cool, then remove wheel cover.
3/32 to 3/4 Large Bit Chuck Part # DA70100PF

Wheel Access Cover

Turn the Quick Change Knob clockwise while holding the Sharpening Wheel to keep it from turning.
3/32" to 1/2" Left-handed Bit Chuck
(for 3/32"-1/2" reverse twist drill bits)

Part # DA02105PF

Standard Diamond Sharpening Wheel (180 grit) Part # DA31320GF
Drill Doctor seen from below.
Remove the wheel, replace, and tighten the Quick Change Knob by turning c o u n t e r- c l o c k w i s e while holding the wheel to keep it from spinning.
Coarse Diamond Sharpening Wheel (100 grit) Part # DA31325GF
WARNING: The use of any accessory other than one recommended in this users manual may present a risk of personal injury.

USA and Canada Only

See Warranty Card insert for countries outside the USA and Canada.
English...1 Espaol..29 Familiarcese con su Drill Doctor.34 Identificacin de las brocas bsicas.35 Partes de una broca..35 Proceso de afilado de Drill Doctor..36 Cmo elegir el ngulo de la punta de la broca en el Modelo 500X..36 Modelo 750X..37 Alineacin de la broca..37 Afilado de la broca..40 Identificacin de brocas correctamente afiladas..41 Puntas hendidas..43 Creacin o sustitucin de una punta hendida..43 Identificacin de brocas hendidas correctamente.44 Tubo adicional para limadura..45 Afilado de brocas de diferentes dimetros, longitudes y tipos...46 Brocas grandes..46 Brocas cortas y brocas ms pequea que 3.2mm (1/8 de pulgada)..46 Brocas para mampostera..47 Uso de la Alineacin Variable para ajustar el ngulo de relieve y de cincel...49 Uso de la Remocin de Material Variable (MTO) en el modelo 750X..50 Preguntas y respuestas..51 Mantenimiento del Drill Doctor..55 Accesorios...58 Garanta...59 Franais..60
Your Drill Doctor is warranted to be free of defects due to workmanship or design for 3 years from the purchase date. If your Drill Doctor fails to operate, or if any operating problem occurs, contact Drill Doctor Technical Service at: 1-888-693-7455 (toll-free USA and Canada only) 1-541-552-1301 Please call 8:00 AM - 3:30 PM Pacific Time. Do not return this product to the store where you purchased it. Do not attempt any service or repairs other than those suggested by a Drill Doctor Technical Service Representative (TSR). During the period of warranty, Drill Doctor will, at our discretion, repair or replace this product free of charge and refund postage or shipping charges providing that the following conditions are met: 1. A copy of the proof of purchase is provided. 2. The product has been operated for the purpose intended as described in the operating instructions and has not been abused or mishandled in any way. 3. The product has not been dismantled and no service or repairs have been attempted other than those suggested by a Drill Doctor TSR. 4. The Return Goods Authorization number (RGA #) (assigned by the Drill Doctor TSR) is written on the shipping label. Please make certain to package items in such a way as to eliminate further damage during shipping. Ship via a traceable carrier and properly insure the package. No CODs are accepted. Unapproved shipping charges are nonrefundable.

Phone/Telfono/Tlphone: 1-888-MYDRILL (693-7455) Professional Tool Manufacturing, LLC P.O. Box E. Hershey St. Ashland, OR 97520 USA Fax/Fax/Tlcopieur: 541-552-1377 Email/Correo Electrnico/Courriel: tech@DrillDoctor.com Web/Direccin en Internet/Site Web: www.DrillDoctor.com

www.DrillDoctor.com

Veuillez remplir ce formulaire pour vos dossiers : No de modle de laffteuse Drill Doctor : _____ _____ _____ Date dachat _____ / _____ / _____ Achete chez _______________________________________
Drill Doctor is a registered trademark of Professional Tool Manufacturing, LLC. Drill Doctor es una marca comercial registrada de Professional Tool Manufacturing, LLC. Drill Doctor est une marque de commerce dpose de Professional Tool Manufacturing, LLC.

PP50110KF

Rev. 0

DRILL BIT SETS AND ACCESSORIES
DRILL DOCTOR 750X PROFESSIONAL WITH FREE SPRING TOOL CENTER PUNCH 4 PC. UNIBIT SET IN DURABLE CASE
Easy Access Easy Access to Enclosed Secure Latch Keep the set from unwanted opening Set Includes: #1 Bit (VSG-102301) 1/8 1/2 by 1/32 steps #2 Bit (VSG-10232) 3/16 1/2 by 1/16 steps #3 Bit (VSG-10233) 1/4 3/4 by 1/16 steps #1T Bit (VSG-15101) 1/8 1/2 by 1/32 steps The DD750X shop model is designed for durability and has the exibility required to sharpen the largest range of dull or broken bits-including split points and masonry bits. The DD750X also adds increased capacity, sharpening 1/2 to 3/4 bits. The precision and accuracy of the DD750X makes this an ideal model for the pro user. One chuck sharpens all sizes 3/32-3/4. Longer jaws hold bit more precisely and jaw guides eliminate jaw twisting on small bits New Push to Stop design on the drill point splitting port will not allow you to over split the bit point Adjustable material take-off allows user to change the amount of bit material you can remove to further extend the life of your bits User replaceable sharpening wheel design for simple replacement. No tool needed Metal point angle shuttle and bracket for added durability New permanent magnet motor produces consistent power, regardless of speed or load Sharpens High-speed Steel, Carbide, Cobalt, TiN-coated and Masonry bits FREE Spring Tool Center Punch (SPT-28R00-1)
DRILL DOCTOR 500X DRILL BIT SHARPENER WITH FREE 3/4 CHUCK
Sharpens standard twist, high-speed steel, masonry, carbide & Tin-coated, cobalt to 118 or 135 point Sharpens split point bits - and lets user Sharpens sizes 3/32 - 1/2 Sharpening time: 30-90 sec. 1.75 amp, 20,000 rpm motor 1.75 amp, 20,000 rpm motor Come with FREE 3/4" Chuck

NEW LOWER PRICE

DAR-DD500XPROMO. $129.95
DRILL DOCTOR 350X HANDYMAN
Sharpens standard twist, high-speed steel, masonry, carbide & TiN-coated, cobalt to 118 point Sharpens sizes 3/32 - 1/2 Patented E-Z Align System Sharpening time: 30-90 sec. 1.75 amp & long lasting diamond sharpening wheel

VSG-10228. $69.95

ATD TITANIUM STEP DRILL BIT SET
Self-starting multiple hole sizes Contains one each of 13 Hole sizes: 1/8 to 1/2 in 1/32 increments 6 Hole sizes from 3/16 to 1/2 in 1/16 increments 9 Hole sizes from 1/4 to 3/4 in 1/16 increments

DAR-DD350X. $69.95

AHN-3018006B

ATD-9210. $26.75

MADE IN USA

UNIBIT STEP DRILL BIT

This rugged Unibit Step Drill quickly provides true round holes in thin 1/8 materials; metal, wood and plastic. 13 holes, 1/8-1/2 in 1/32 increments. 1/4 shank Self-starting tip

DAR-DD750XPROMO. $166.60

IRWIN HANSON DRILL BIT SETS
ITEM # AHN-30520 AHN-60148 AHN-3018002B AHN-3018006B AHN-73149 MODEL VER-10141 VER-10144 VER-10245 VER-12645 PIECES DESCRIPTION 5 Left Hand, Mechanics Length COBALT 29 General Purpose, 3/8 Reduced Shank 29 Cobalt Drill Bit Set 29 Drill Bit Set 21 TURBOMAX , HSS SAE

VSG-10231. $18.55

12 PC. 1/8 DOUBLE-ENDED TITANIUM DRILL BIT SET
Titanium Coated High Speed Steel Twelve, 1/8 Drill Bits

TITANIUM DRILL BIT SET

Heavy duty steel index box 29 sizes from 1/16 - 1/2 by 64ths Lasts up to 6 times longer than standard bits Penetrates 75% faster, Bits can be sharpened Long-lasting titanium nitride coated set ts 3/8 drills
PRICE $25.25 $80.95 $141.50 $99.95 $54.50 PRICE $46.35 $83.50 $16.90 $159.95

VERMONT AMERICAN DRILL BIT SETS
VER-10144 PIECES DESCRIPTION High speed High speed High speed Cobalt SIZES 1/16 - 3/8 1/16 - 1/2 1/16 - 1/4 1/16 - 1/2

RHO-9211. $23.99

ATD-9204. $9.25

POWER HEX BITS SETS

45 PC. MULTI-USE POWER BIT SET
5 high speed steel quick-disconnect drill bits 7 power nut drivers 14 power screwdrivers 13 double end screwdriver bits 14 adaptor Magnetic bit extension 3 bit holders Blow mold case
30 PC. FASTENER DRIVE SET
Full range of fastener bits, nutsetters, accessories and sets Insert bits are compact and versatile. Use as hand tool or power tool accessories Organized storage case

TTN-16044. $9.95

AHN-357030. $19.95 All IRWIN fastener drive bits are manufactured from industrial grade tool steel & tested to meet the highest standards for hardness & torque.
90 PC. BIT SET WITH REVERSIBLE RATCHET

ATD-549.$13.99

TAP & DIE SETS
117 PC. MACHINE SCREW, FRACTIONAL & METRIC TAP & DIE DRILL BIT SET
High carbon steel for durability and precision threading 34 plug tap sizes are perfect for general purpose threading 34 hexagon die sizes are ideal for general maintenance and repair work Hexagon dies allow a socket or wrench to be used in areas with limited space 36 high speed steel drill bits with drill to tap size interchange chart 5 spiral ute screw & bolt extractors
75 PC. FRACTIONAL/METRIC GEARWRENCH TAP AND DIE SET
Accommodates Taps and Dies from #4 - 1/2 & 3-12mm Carbon steel Set includes: Tap and Die Ratcheting T Wrench, Small Tap Adapter, Medium Tap Adapter, Die Adapter, Sliding T for adapters, 34 taps and 34 dies, SAE screw pitch gauge, Metric screw pitch gauge, and a #5 screwdriver

ATD-277. $129.95

KDT-3887. $169.95
76 PC. MACHINE SCREW, FRACTIONAL & METRIC TAP & DIE SET
High carbon steel for durability and precision threading 34 plug tap sizes are perfect for general purpose threading 34 hexagon die sizes are ideal for general maintenance and repair work Hexagon dies allow a socket or wrench to be used in areas with limited space
117 PC. FRACTIONAL/METRIC TAP, DIE & DRILL BIT DELUXE SET

VER-pc. Hanson high-speed steel drill bit set 5 spiral screw extractors Complete assortment of high quality, high-carbon steel taps & dies Tap/drill chart, featuring metric & fractional sizes & tool diagram included A variety of tap wrenches, die stocks, thread pitch gauges, and a screwdriver

ATD-276. $89.95

AHN-26377. $299.95
75 PC. MASTER TAP AND DIE SET
Professional quality For cutting internal and external threads Heat-treated and tempered carbon tool steel Smooth accurate threading
76 PC. FRACTIONAL/METRIC TAP AND DIE SET
Includes plug tap and hexagonal die in sizes from 3mm to 12mm and #4 to 1/2 in ne and coarse threads, plus 1/8-27BSP and 1/8-27NPT pipe taps and dies. Set also comes with plain die stock, adjustable die stock, adjustable handle tap wrench, T-tap wrench, T-tap wrench with 3/8 square drive, 16-leaf metric thread pitch gage, 18-leaf standard thread pitch gage, mini screwdriver

VER-21741. $199.95

58 PC. METRIC MASTER MECHANICS SET

VER-21750. $224.95

AHN-26376. $199.95

EXTRACTORS

8 PC. STUD REMOVER SET
Designed and tested to reach studs in difcult work areas. 1/2 Drive for 10mm, 12mm, 3/8 Drive for 6mm, 8mm, 1/4 and 5/16 stud sizes. 3/8 and 7/16 stud sizes. Weight: 2.3 lbs
25 PC. SCREW EXTRACTOR/ DRILL & GUIDE SET
Use on thread sizes 5mm to 16mm Blow molded case Remove broken fastener Turn broken fasteners out
35 PC. SCREW EXTRACTOR DRILL BIT SET
Thirteen Multi-Spline screw extractors Sixteen sizes of Left Hand drill bits Six spiral screw extractors

AST-9447.$49.95

AHN-11135. $156.50

ATD-6508.$43.50

SCREW EXTRACTOR HEX HEAD MULTI-SPLINE
25 Piece Screw Extractor Set (1/8 7/8) AHN-53227
7 PC. POWER GRIP SCREW AND BOLT EXTRACTOR SET
Power Groove work with Quick Change Adapter Grips both standard and metric size fasteners

5 PC. BOLT-GRIP BASE SET

Set includes: 3/8 Bolt Ext 3/8 Drv 7/16-11mm Bolt Ext 1/2 Bolt Ext 3/8 Drv 9/16 Bolt Ext 3/8 Drv 5/8 Bolt Ext 3/8 Drv

VSG-394100. $27.95

AHN-53227. $56.90
10 PIECE SCREW Extractor Set (1/8 13/32)
10 PC. SCREW EXTRACTOR SET
5 left hand cobalt drill bits & 5 spiral extractors

VSG-394001. $26.95

AHN-53226.$25.95

AHN-11119. $35.50