IUC-4100 UltraSmart In-Ground Fence
Rechargeable In-ground Pet Fencing System Adapter: 24v <400 mAmps AC Only Adapter is good if there is a light on the wall transmitter Connection is made inside the transmitter Audible alarm volume can be adjusted by this dial (Minimum setting is low volume; it does not silence the alarm) Transmitter has battery backup powered by 8 AA alkaline batteries (not included) When operating under backup power, there will be no light on transmitter and a tone will sound every 5 seconds. (Battery Backup Monitor must be ON.) Battery life = up to 40 hours Slide switch can be set to On or Off. Used to turn off alarm if backup batteries are not used. A full charge takes 2-3 hours and lasts 1-3 months depending on use. Place collar on charge station for 2-3 hours (Collar fits in the cradle with the contacts facing down through the holes in the case. Innotek logo facing out ). The collars light will glow red when collar is properly seated and charging. The collar light will then turn green when charging is complete. Is not used with this system. Needs to be turned off IUA-005 Ultra Collar Charging Station Plugs in wall outlet. Collar straddles charger, probes insert into wells. Spring-loaded pin must make contact with recessed point in receiver to insure proper charging. Collar should glow red when properly seated. Collar: Rechargeable Lithium Ion battery and waterproof Collar measures 1.25 wide X 2.75 long X 0.75 X thick and weighs 4.0 oz with strap. Blue polyurethane strap (RK-22) Circumference ranges 8-24 inches.
Alarm Volume: Battery Backup:

Battery Backup Monitor:

Charge:
Charge Reminder: Charging Station:

Revised Last 1/5/2005

1 of 6

IUC-4100troubleshooting

Collar Lights and Tones: Status Light Pulsating Green Pulsating Red Continuous Green Blinking Green Blinking Amber Blinking Red No light
Tones With Tone Duration of the Stimulation No Tone No Tone No Tone No Tone No tone
Condition Warning tone on Low or Med Stimulation being delivered (up to 10 seconds) Over stimulation warning; collar locked for 10 secs. Collar battery 60% strength or more Collar battery 60-20% strength Collar battery less than 20% strength; charge immediately Collar is completely discharged or Stimulation locked out after 3 cycles of stim/off (resets to blinking green when
collar goes back into safe zone)
After removing collar from charger Continuous Red for 3 No Tone secs., give charge status light (see above) then blink amber Continuous Red With Tone (20 secs.) Blinking Amber No Tone Blinking Green While on charger Solid Red Solid Green No light Frequency: Field Size: 8.192 kHz Slide switch = Large Slide switch = Small Will Click; 5 consecutive clicks for confirmed fit. No Tone No Tone No Tone
Self-test/ReadyTest in progress, Passed Self-test Self-test failure; unit is not operational Collar is in PerfectFit mode for 90 secs. After charging PerfectFit mode indicates collar is making true contact with dogs skin Charge in progress Charge complete Charge failure/collar not properly seated/or no power to outlet

Installations using 1000+ feet of wire Installations using less than 1000 feet of wire

Field Width Adjustment:

Dialed inside transmitter Customer must test signal field after making any adjustments. Field width may be reduced when operating on backup batteries

LP-4100-1:

Optional for additional lightning protection Transmitter is not covered for lightning or power surge unless LP-4100-1 is installed

2 of 6

Mismatch:
Will work with other Innotek containment components operating on 8.192 kHz It is also compatible with a ZONES xmtr. May need IUA-005 to charge collar if adding to existing system. Remove collar from charging station. Collar light will glow for about 3 seconds. Do not touch the probes during this period. Note: light will glow red during self-test, and then go either Green/Amber/or Red, depending on battery strength. After about 5 seconds, collar light will begin to flash amber (in PerfectFit mode). Place collar on dog. When collar is properly fitted on dog, the light will start flashing green and 5 consecutive click tones will be emitted. Collar is now ready for use. Note: fit test emits a slight stimulation pulse, almost imperceptible. Its less than one-quarter of a level 1 stimulation. To skip the PerfectFit test, either 1) wait 90 seconds after removing from charger or 2) touch to your skin for 5 clicks before putting on dog.

Perfect Fit

Power: Probes:
Slide switch can be set to On or Off Comes with Black plastic acorn nuts for training that deliver no stimulation. Also comes with a set of short and long probes Short probes are.40 or 4/10 of an inch. Long probes are.60 or 6/10 of an inch. Probes available in the RK-23 Powered for up to 25 acres Place collar on charging station for 5 seconds Remove collar from charging station. Collar will glow red for 3 secs., then go to either Green/Amber/or Red depending on battery strength, then blink amber (goes into PerfectFit mode) if collar is good. **If collar light glows red for 20 seconds, repeat the ReadyTest. If it continues to glow red, collar is bad Wire nuts placed in waterproof gel-filled capsules (RK-15 = 6 splice kit) Adjustable in transmitter with increase to the run-through as dog approaches the wire Slide switch inside transmitter can be set to Low, Medium or High The run-through prevention is more intense than High Maximum stimulation is 10 seconds, off 10 seconds; maximum of 3 on-off cycles

Range: Ready Test

Splices: Stimulation:

3 of 6

Transmitter:
Uses a 24 Volt AC adapter Weather-Resistant Alarm Tone None Tone twice per second Tone once per second Three one-second reminder tones every minute Tone once every 5 seconds None Condition Power on / System ok Wire break or disconnect Backup batteries low (Backup battery reminder switch must be ON.) Receiver recharge reminder This is not used with this system. Turn reminder switch off. Power disconnected operating on backup batteries. Transmitter is off or power is disconnected.

Transmitter Lights and Alarms: Light Solid Green Flashing Red Flashing Yellow Flashing Red and Green No light No light 2200008-1: Warranty: Wire: Wire Terminals:
DVD - How to Use, 4 in 1 Transmitter is not covered for lightning or power surge unless LP-4100-1 is installed Comes with 500 feet of 20 gauge wire for direct burial - green insulation Connection is made inside the transmitter

4 of 6

IUC-4100 Containment Troubleshooting Tips
Dog does not feel stimulation: Check collar tightness, Check probes Remove metal tags and collars Check charge on collar Verify that the transmitter is on Increase stimulation level Perform Ready test and Perfect Fit test Dog runs through: Check collar tightness, check probes, Perform Perfect Fit test, Increase stimulation level Increase field width More training is needed Used non-waterproof connections in boundary wire Do test loop. If signal is consistent on test loop Check for nick or scrape in wire insulation (RF Choke) Reduce stimulation level Restore dogs personality and try training at another time More training is needed Decrease field width Change field size switch to SM Check for buried cables or metal in yard Move wall transmitter away from electrical appliances Remove the collar when dog is in house Move boundary wire farther from the house Move transmitter away from dogs indoor area Check status panel inside transmitter lid Check for damaged wires outside entry to house Perform Test Loop / RF Choke Check adapter is plugged in properly Check outlet See if GFCI outlet was tripped Check voltage of adapter; should be > 24 volts AC Increase field width Change yard size to LG Check for damaged wires Check for mixture of gauges in containment wire Perform Test Loop

Signal is intermittent:

Dog afraid of yard:
Stimulations in safe zone: (high range)

Stimulations in house:

Transmitter is alarming: Broken wire alarm: No light on transmitter:

Field width is low:

5 of 6
Collar not taking a charge:
If collar does not glow red when on charging station check the following: Collar is properly seated on charging station Outlet has power Charging port on collar is clean There is no coating on probe tips Collar strap is not pushing receiver up off charging station If the collar still does not glow red, the charging station is bad. If the collar does glow red when on charging station, then goes out after removing without performing ReadyTest, the collar is bad.

6 of 6

IUC-5100
Deluxe Rechargeable Contain N Train In-ground Pet Fencing System With Fastrak wire and Lightning Protection 1. Set Up Handheld Transmitter: Remove battery door and install 12 volt alkaline battery (Requires small standard screwdriver or small coin)
2. Training Stimulation: Press the collar select button to select collar 1 Press the to increase the stimulation level Press the to decrease the stimulation level 3. Set up Collar Place collar on charge station for 2-3 hours (Collar fits in the cradle with the contacts facing down through the holes in the case. Innotek logo facing out ). The collars light will glow red when collar is properly seated and charging. The collar light will then turn green when charging is complete. Press the collar select button to select collar 1 Hold the side of the remote to the side of the collar, opposite the Logo. Press and hold the tone button. The collar will emit a tone and the light will glow solid green when turning On or solid red when turning Off.

4. Training mode On/Off:

**When using a 2nd collar, repeat steps 2-4 selecting collar 2 on remote before turning 2nd collar on. **(When using 2nd collar make sure collars are at least 2 ft apart)** **Note: System will be synchronized every time the collar is turned on** 5. Perfect Fit Test: (initiating with remote) Before placing collar on dog, turn the collar on and continue to hold the tone button for 3 seconds. The collar will emit a long tone indicating Perfect Fit mode has started. When collar is properly fitted on dog, 5 consecutive click tones will be emitted. Collar is now ready for use *To skip the Perfect Fit test, just turn the collar ON by pressing the tone button less than 3 seconds. The collar will function normally, bypassing the Perfect Fit test.** ** Note: fit test emits a slight stimulation pulse, almost imperceptible. Its less than one-quarter of a level 1 stimulation
1 of 8 IUC-5100troubleshooting Revised 1/18/2010

Adapter:

24v <400 mAmps AC Only Adapter is good if there is a light on the wall transmitter Connection is made inside the transmitter Audible alarm volume can be adjusted by this dial (Minimum setting is low volume; it does not silence the alarm) Handheld Transmitter uses 12 volt alkaline batteries, Battery life = 24hrs Min. Containment Transmitter. Can be battery backup powered by 8 AA alkaline batteries (not incl.) When operating under backup power, there will be no light on transmitter and a tone will sound every 5 seconds. (Battery Backup Monitor must be ON.)Battery life = up to 40 hours Slide switch can be set to On or Off. Used to turn off alarm if backup batteries are not used.
Alarm Volume: Batteries: Battery Backup:

Battery Backup Monitor:

Charge:
A full charge takes 2-3 hours and lasts (1-3 months containment) (up to 100hrs training mode) depending on use. Place collar on charge station for 2-3 hours (Collar fits in the cradle with the contacts facing down through the holes in the case). The collars light will glow red when collar is properly seated and charging. The collar light will then turn green when charging is complete. Is not used with this system IUA-005 Ultra Collar Charging Station
Charge Reminder: Charging Station: Collar:
IUC-5225 Rechargeable Lithium Ion battery and waterproof Collar measures 1.25 wide X 2.75 long X 0.75 X thick and weighs 4.0 oz with strap. Blue polyurethane strap (RK-22) Circumference ranges 8-24 inches.
2 of 8 IUC-5100troubleshooting Revised 1/18/2010
Collar Lights and Tones: Status Light Pulsating Green Pulsating Red Continuous Green Single Blinking Green Dual Blinking Green Blinking Amber Blinking Red No light
Tones Duration of tone button pressed in training, or warning tone on containment Duration of the stimulation In either mode No Tone in either mode No Tone, Contain Only No Tone, Contain & Train No Tone No Tone No tone
Condition Tone only no stimulation Warning tone on Low or Med Stimulation being delivered (up to 10 seconds) Over stimulation warning; collar locked for 10 secs. (containment or training) Collar battery 60% strength or better Collar battery 60-20% strength Collar battery less than 20% strength; charge immediately Collar is completely discharged or Stimulation locked out after 3 cycles of stim/off (containment-resets to blinking green

when collar goes back into safe zone)
After removing collar from charger Continuous Red for 3 No Tone secs., give charge status light (see above) then blink amber Continuous Red With Tone ( 20 secs.) Blinking Amber Blinking Green While on charger Solid Red Solid Green No light Frequency: 8.192 kHz Field Size: No Tone Will Click; 5 consecutive clicks for confirmed fit. No Tone No Tone No Tone
Self-test/ReadyTest in progress, Passed Self-test Self-test (ready test) failure; unit is not operational Collar is in PerfectFit mode for 90 secs. After charging PerfectFit mode indicates collar is making true contact with dogs skin Charge in progress Charge complete Charge failure
Slide switch = Large Slide switch = Small
Installations using 1000+ feet of wire Installations using less than 1000 feet of wire

Field Width Adjustment:

Dialed inside transmitter Customer must test signal field after making any adjustments. ** Field width may be reduced when operating on backup batteries

LP-4100-1:

Included for additional lightning protection Transmitter carries a 1-year mfr warranty even with the LP-4100-1 installed Transmitter is not covered for lightning or power surge unless LP-4100-1 is installed
3 of 8 IUC-5100troubleshooting Revised 1/18/2010

Mismatch:

Will work with other Innotek containment only components operating on 8.192 kHz It is also compatible with a ZONES transmitter. May need IUA-005 to charge collar if adding to existing system. Remove collar from charging station. Collar light will glow for about 3 seconds. Do not touch the probes during this period. Note: light will glow red during self-test, and then go either Green/Amber/or Red, depending on battery strength. After about 5 seconds, collar light will begin to flash amber (in PerfectFit mode). Place collar on dog. When collar is properly fitted on dog, the light will start flashing green and 5 consecutive click tones will be emitted. Collar is now ready for use.
Perfect Fit (off charger)

(initiating with remote)

Before placing collar on dog, turn the collar on and continue to hold the tone button for 3 seconds. The collar will emit a long tone indicating Perfect Fit mode has started. When collar is properly fitted on dog, 5 consecutive click tones will be emitted. Collar is now ready for use Note: fit test emits a slight stimulation pulse, almost imperceptible. Its less than one-quarter of a level 1 stimulation. To skip the PerfectFit test, either 1) wait 90 seconds after removing from charger or 2) only pressing tone button quickly in training 3) touch to your skin for 5 clicks before putting on dog.

Power: Probes:

Slide switch can be set to On or Off Comes with Black plastic acorn nuts deliver no stimulation. Also comes with a set of short and long coated probes Short probes are.40 or 4/10 of an inch. Long probes are.60 or 6/10 of an inch Available in the RK-23 Powered for up to 25 acres in containment, Up to 150 yards in training. Wire nuts placed in waterproof gel-filled capsules (RK-15 = 6 splice kit) Adjustable in transmitter with increase to the run-through as dog approaches the wire. Slide switch inside transmitter can be set to Low, Medium or High. The runthrough prevention is more intense than High. Maximum stimulation is 10 seconds, off 10 seconds; maximum of 3 on-off cycles Programmable, 9 levels, Displayed on transmitter Over-Stimulation protection = 10 second lock-out period after 10 seconds of stim.

Range: Splices:

Stimulation: Containment:

Remote training:

4 of 8 IUC-5100troubleshooting Revised 1/18/2010
Transmitter (handheld) Buttons: Red central button + or button Green Tone button Collar select button Boost button = offers continuous stimulation = adjust stimulation levels from 1-9 = offers tone only, no stim. Also used to turn collar on/off = switches remote control from collar 1 to collar 2 = boosts stim by 2 levels while holding down button
Transmitter (handheld)Display: Lower Left side = Dog 1 collar selected Lower right side = Dog 2 collar selected Center number = Correction level for selected dog Flashing L = Low battery indicator **Note: cold temperatures may lead to premature low batt indication. Blank = Display blanks 30 minutes after the last button is pressed. Transmitter (wall): weather resistant --uses the 24 volt AC adapter Condition Power on / System ok Wire break or disconnect Backup batteries low (Backup battery reminder switch must be ON.) Receiver recharge reminder This is not used with this system. Turn reminder switch off. Power disconnected operating on backup batteries. Transmitter is off or power is disconnected.
Containment Transmitter Lights and Alarms: Light Alarm Tone Solid Green None Flashing Red Tone twice per second Flashing Yellow Tone once per second Flashing Red and Green No light No light 2200008-1: Warranty: Three one-second reminder tones every minute Tone once every 5 seconds None
DVD - How to Use, 4 in 1 Lightning Protector supplied with system has a 1 year warranty Transmitter is not covered for lightning or power surge unless LP-4100-1 is installed Comes with 500 feet of 20 gauge wire for direct burial - green insulation Comes with 100 feet of Fastrak wire Connection is made inside the transmitter

Wire: Wire Terminals:

5 of 8 IUC-5100troubleshooting Revised 1/18/2010

IUC-5100 Containment Troubleshooting Tips
Dog does not feel stimulation: Check collar tightness, Check probes Remove metal tags and collars Check charge on collar Verify that the transmitter is on Increase stimulation level Perform Ready test and Perfect Fit test Dog runs through: Check collar tightness, Perform Perfect Fit test, check probes Increase stimulation level Increase field width More training is needed Used non-waterproof connections in boundary wire Do test loop. If signal is consistent on test loop Check for nick or scrape in wire insulation (RF Choke) Reduce stimulation level Restore dogs personality and try training at another time Decrease field width Change field size switch to SM Check for buried cables or metal in yard Move wall transmitter away from electrical appliances Remove the collar when dog is in house Move boundary wire farther from the house Move transmitter away from dogs indoor area Check status panel inside transmitter lid Check for damaged wires outside entry to house Perform Test Loop / RF Choke Check adapter is plugged in properly Check outlet See if GFCI outlet was tripped Check voltage of adapter; should be > 24 volts AC Increase field width Change field size switch to LG Check for mixture of gauges in containment wire Check for damaged wires Perform Test Loop

Signal is intermittent:

Dog afraid of yard: Stimulations in safe zone: (high range)

Stimulations in house:

Transmitter is alarming: Broken wire alarm: No light on transmitter:

Field width is low:

6 of 8 IUC-5100troubleshooting Revised 1/18/2010
Collar not taking a charge:
If collar does not glow red when on charging station check the following: Collar is properly seated on charging station Outlet has power Charging port on collar is clean There is no coating on probe tips Collar strap is not pushing receiver up off charging station If the collar still does not glow red, the charging station is bad. If the collar does glow red when on charging station, then goes out after removing without performing ReadyTest, the collar is bad
7 of 8 IUC-5100troubleshooting Revised 1/18/2010
IUC-5100 Remote Training Troubleshooting Tips
Check batteries for proper size, type, and position. Make sure there are 2 green lights flashing on collar. Reset collar (Initiate ReadyTest) Place collar on charging station for 5 seconds Remove collar from charging station collar should glow red for 3 secs., give charge status light then blink amber if collar is good. **If collar light glows red for 20 seconds, repeat the ReadyTest. If it continues to glow red, collar is bad.

**Note: Do not touch probes when removing collar from charging station, this will result in a ReadyTest failure** Turn collar on/off System is operational if collar light goes green and emits a tone **If no lights on collar and it has passed ReadyTest, xmtr is bad. Perform ReadyTest Turn collar on/off to verify collar properly matched to xmtr Check tightness of probes Perform ReadyTest Turn collar on/off to verify collar properly matched to xmtr **If no tone during on/off, collar is bad Check batts and charge on collar. Perform ReadyTest Walk through on/off procedure **If it still does not respond, replace xmtr if collar passes ReadyTest Shut collar 2 off. Select collar 2 on remote first, then turn collar 2 back on. It will now work on dog 2. Change the ID Code by removing xmtr batts, then press any button Replace xmtr batts then turn collar on. Recharge the collar and/or change the batteries in transmitter Go through on/off procedure. Replace both pieces if still low range. ** Keep hands away from antenna**
Collar will not deliver stimulation:
Collar will not deliver tone:
Collar will not respond to remote:
Collars both work on dog 1:

Interference: Low Range:

8 of 8 IUC-5100troubleshooting Revised 1/18/2010