EPSON GT-10000 Scanner Parts
Scanning resolution: Output resolution: Command level:
carriage (at home position) document table
600 dpi main 2400 dpi sub with micro-step 50 to 4800 dpi (1-dpi increments) ESC/I-B7 RGB color filters on CCD Monochrome: 1-pass scanning Color byte sequence: 1-pass scanning (R, G, B) Color line sequence: 1-pass scanning (R, G, B) 50 to 200 percent in 1-percent increments 36 bits input; 24 bits output (color) 12 bits input; 8 bits output (grayscale) 7 levels Fixed threshold with Text Enhancement Technology (TET) enabled AAS (Auto Area Segmentation) Enable/disable selectable 3 halftoning modes (A, B, and C) 4 dither patterns (A, B, C, and D) for bi-level and quad-level data (2 downloadable dither patterns) 2 user-defined dither patterns (A, B) 2 types for CRT display 3 types for printer 1 user-defined table 1 type for CRT display 3 types for printer output (available in color byte sequence mode and color line sequence mode) 1 type user-defined SCSI II (two 50-pin high-density connectors) Automatic Document Feeder (ADF) Opaque documents with smooth surfaces Xenon fluorescent lamp Main unit MCBF: 100,000 cycles of carriage movements

document cover

Color separation: Reading sequence:
control panel ] Start button transportation lock
Zoom: Image data: Brightness: Line art settings:
terminator switch SCSI ID dial

Halftoning process:

Gamma correction:
SCSI interfaces ADF interface

AC inlet

Color correction:

Scanner Specifications

Scanner type: Photoelectric device: Effective pixels: Document size: Flatbed, color Color CCD line sensor 7020 dots 10200 pixels at 600 dpi, 100% 11.7 17.0 inches (mm) (the reading area can be specified from your software) Interface: Options: Supported documents: Light source: Reliability:

EPSON GT-10000 - 2

EPSON GT-10000
Noise: Dimensions: Under 50 db (operating) Width: 25.8 inches (656 mm) Depth: 18.0 inches (458 mm) Height: 6.9 inches (176 mm) Approximately 46.3 lb (21 kg) 230 V Safety standards: EN 60950 (VDE) EMC EN 55022 (CISPR Pub 22) class B AS/NZS 3548 class B

Weight:

CE marking Low Voltage Directive 73/23/EEC: EMC Directive 89/336/EEC:

Electrical

Input voltage range: Rated frequency: Rated current: Power consumption: 100 to 120 VAC 220 to 240 VAC; universal auto-switching 50 to 60 Hz 100 to 120 VAC1.2 A 220 to 240 VAC0.7 A Operating Approximately 50 W (approximately 55 W with the ADF
Check the label on the back of the scanner for voltage information.

EN60950

EN 55022 Class B EN 61000-3-2 EN 61000-3-3 EN 50082-1 IEC 801-2 IEC 801-3 IEC 801-4

SCSI Interface

Interface type: Functions: ANSI X3T9.2/375R Revision 10L (SCSI II) BUS FREE phase ARBITRATION phase SELECTION/RESELECTION phase COMMAND phase (the Logical Unit Number is fixed at 0 and the Command Link Function is not supported) DATA phase DATA IN phase DATA OUT phase STATUS phase MESSAGE phase MESSAGE IN phase MESSAGE OUT phase ATTENTION condition RESET condition TTL compatible

Environmental

Temperature: Operating 41 to 95 F (5 to 35 C) Standby 13 to 140 F (25 to 60 C)
Humidity (without condensation): Operating 10 to 80% Standby 10 to 85% Operating conditions: Ordinary office or home conditions; avoid dust, direct sunlight, or strong light. Be sure the outlet provides enough power.

Logic level:

Safety Approvals
120 V Safety standards: UL 1950 with D3 CSA C22.2 No. 950 with D3 EMC FCC part 15 subpart B class B (USA) CSA C108.8 class B (Canada)
Electrical standard: ANSI X3T9.2/375R Revision 10L (SCSI II) ID Setting: Terminator: Selectable from 0 to 7 (factory setting: 2) Internal terminator selectable (enable/ disable)

3 - EPSON GT-10000

Connector type: Two Micro DB-50 high-density connectors

Documents Supported

Document size: Portrait: A3, Ledger, B4, Legal, A4, Letter, B5, A5, 5.5 5.8 inch (mm) Landscape: A4, Letter, B5, Asheets of 21 lb (80 g/m2) paper: A4, Letter or smaller 30 sheets of 21 lb (80 g/m2) paper: B4, Legal or larger High-quality bond paper High-quality paper, ink jet paper, bond paper 13 to 33 lb (50 to 127 g/m 2)
Dont use the following paper types: transparencies, tracing paper, coated paper (such as photo quality and glossy paper), labels, multipart forms, carbon paper, or paper with staples, holes, rips, curls, or folds.
Connector pin arrangement:

Feeding capacity:

Initialization methods
Scanner is turned on or receives a SCSI Reset signal from the SCSI interface (hardware initialization). Scanner receives a SCSI Bus Device message or an Esc @ command from the software (software initialization)
Ejecting capacity: 100 sheets Paper quality: Compatible paper types: Paper thickness:
Optional Automatic Document Feeder (GT10000ADF)
The ADF allows you to automatically load multi-page documents into your scanner.

General

Type: Document feeding: Page feeding and duplex scanning with automatic reverse Pages are center aligned, fed face up from bottom of stack, and ejected face up Consumption current: Insulation resistance: Dielectric strength:
Power supply: Supplied through the scanner 24 10% VDC 5 10% VDC 24 VDC: 2.0 A 5 VDC: 0.3 A 10 m or more at 500 VDC (between AC line and chassis) 1000 VAC per minute (between AC line and chassis)
Document replacement time: 1.2 seconds (Letter/A4 landscape) Multiple sizes: Noise: Reliability: Unavailable; all documents in a stack must be the same size 50 dB or less 100,000 sheet paper feeding life 100,000 sheet paper ejecting life 100,000 hinge closings Width: 23.6 inches (601 mm) Depth: 20.8 inches (528 mm) Height: 4.8 inches (122 mm) 35.2 lb (16 kg)

Dimensions:

Resistance to static electric noise: Case: Operated properly at 10 kV or less Metal: Operated properly at 7 kV or less

EPSON GT-10000 - 4

Error conditions
Flashing Off Interface error: Make sure the scanner is securely connected to the computer, and then turn the scanner off and back on again. Fatal error: Make sure the transportation lock is released, and then turn the scanner off and back on again. Option error: Theres a problem with the ADF unit. Make sure the ADF is flat against the document table. Make sure it is securely connected to the ADF connector at the back of the scanner. Finally, make sure the ADF isnt out of paper and doesnt have a paper jam.

Lights and Buttons

The scanner has three indicator lights and two buttons on its control panel. A ] Start button is located beside the document table. Light status and button functions are described in the tables that follow.
RESET button OPERATE button

Flashing

ERROR light
OPERATE light READY light

Transporting the Scanner

When you transport the scanner a long distance or store it for an extended time, follow these steps to secure the carriage:

Scanner indicator lights

Light READY Light status On Flashing ERROR On Flashing Red Color Green Scanner status Ready to scan images Scanning in progress An error has occurred
1. Make sure the transportation lock on the side of the scanner is in the UNLOCK position. 2. If youre using an automatic document feeder, remove it and replace the scanner cover. 3. Turn on the scanner and wait until the carriage moves to the home position (toward the left of the scanner). Then turn off the scanner.
If the scanner is inoperable, the carriage may not automatically return to the home position. If it doesnt, raise the right side of the scanner and hold it up until the carriage comes to rest at the left side. Then turn the transportation lock to the locked position.

Scanner buttons

Button Function Turns the scanner on and off. Initializes the scanner. Automatically launches a ] Start button-compatible application. You must set up your scanner software and a compatible application to use this feature with any application other than Presto! PageManager. If you installed Presto! PageManager, its automatically assigned to the ] Start button. You can set up Presto! PageManager to scan your image automatically and send it directly to another application or a peripheral device, such as a printer.

P OPERATE

] Start
4. Slide the transportation lock to the LOCK position.

Scanning with EPSON TWAIN Pro
Here is a brief overview of the scanning steps using EPSON TWAIN Pro (or EPSON TWAIN Pro Network). 1. Open your host application (for example, PhotoDeluxe Business Edition). 2. Select your scanner source. (Unless you change your source, you need to do this step only once.) For example, if youre using PhotoDeluxe Business Edition as your host application, click the Get & Fix Photo button. Click the Get Photo tab, then click the arrow below the Scanners button. Select EPSON TWAIN Pro and click OK.
ERROR light On READY light On Error type Command error: The scanner has received incorrect commands from the scanning software. Try rescanning.

5 - EPSON GT-10000

If youre accessing a network scanner connected to another computer, select EPSON TWAIN Pro Network as your input source and click OK.
You cant select EPSON TWAIN Pro as your scanner source if youre using a network scanner and EPSON Scan Server is running. EPSON Scan Server disables EPSON TWAIN Pro
6. Click the Preview button. You see a preview of your scan in the window that opens.

Preview button

Marquee button
3. Open your scanner driver. In PhotoDeluxe, do one of the following: t Click the Get & Fix Photo button. Click the Get Photo tab, then click the Scanners button. Click the 1 Mode tab, then click the Custom button. t Choose File, Open Special, then select Scan Photo.
The command you choose from the File menu depends on the host application. With some applications, you might choose Acquire or Select Source instead of Open Special.
7. Choose your scan settings.
Auto Locate button to automatically define Click the the scan area around the edges of your image. You can also adjust the scan area by positioning the mouse pointer over the dotted line around the marquees edge and dragging the box to resize the marquee. Color Adjustment button and use the Gray Click the Balance Intensity feature if you need to remove color cast from your image. Auto Exposure button to automatically set Click the the highlight and shadow exposure.
Generally its a good idea to use the Auto Exposure button to obtain the best settings for your scan.
4. The EPSON TWAIN Pro main window appears.
8. When youve finished making adjustments, click the Scan button. The READY light on the front of the scanner flickers while its scanning. In a few moments, a scanned image is imported into your host applications window. Then click Close to close the EPSON TWAIN Pro or EPSON TWAIN Pro Network window and return to your application.
click to display a preview of the image

click to start scanning

5. Choose the Document Source, Image Type, and Destination. For example, if youre scanning a photograph to print, select

Flatbed as your Document Source, 24-bit Color [Std] as your Image Type, and EPSON Stylus Printer [Photo]

Scanning Color Images

If the colors in your scanned image dont match those in your original document, try experimenting with the Unsharp Mask setting. Click the Destination button on the EPSON TWAIN Pro or EPSON TWAIN Pro Network main window to display the Destination window, and then select or deselect Unsharp Mask.
as the Destination, if youre sending the scanned image to an EPSON Inkjet printer. If youre using the optional automatic document feeder, select either ADF - Single-sided or ADF - Double-sided as your Document Source.

EPSON GT-10000 - 6

t When you return to the client computer, your scanned images appear in the host applications window. Close EPSON TWAIN Pro Network to end your connection to the scanner server and allow other client computers to use the scanner.
Some applications automatically close the client computers connection to the scanner server when you press the ] Start button. You cant scan multiple images if youre using these applications.

Selecting Resolution

As a rule of thumb for most images except line art, use a scanning resolution that is approximately one third of your output resolution. For example, use a scanning resolution of up to 100 dpi with a 300 dpi laser printer, and up to 200 dpi with a 600 dpi laser printer. For 1440 dpi ink jet printers, use a scanning resolution of up to 300 dpi. Try a scanning resolution of 240 dpi for 720 dpi printing. Keep the following in mind when you choose a resolution: t The higher the resolution you select, the larger the resulting image file will be. To keep your file size manageable, select the lowest possible resolution that gives acceptable quality. t If you need to scan at a higher resolution, you can reduce the size of the resulting image file by scanning only part of the image.

Starting a Network Scan

You can start a scan on your network scanner in several ways: t You can start EPSON TWAIN Pro Network on the client computer, make your scan settings, and click the Scan button on the EPSON TWAIN Pro Network main window. t You can press the ] Start button on the scanner to send the scanned image to the client computer that is currently connected to the scanner server. t You can click the Start button on the EPSON Scan Server dialog box to send the scanned image to the client computer currently connected to the scanner server.

Using a Network Scanner

Network scanning involves the following steps: t The scanner must be connected to the scanner server. t The scanner and scanner server must be turned on and running EPSON Scan Server. t From the client computer, start the host application, then start EPSON TWAIN Pro Network to establish a connection to the scanner server. Only one client computer at a time can connect to the scanner server. t Choose the Image Type, Resolution, and other settings you want for your scan. t Place your first image on the document table (or in the automatic document feeder). t Start the scan. Although this can be done from EPSON TWAIN Pro Network on the client computer, it may be more convenient to press the scanners ] Start button or to start the scan from the scanner server. Then you can scan several images with a single trip to the scanner. t If you want to scan more than one image, place your second image on the document table and press the scanners ] Start button again. Repeat this step for every image you want to scan. (The settings you chose for the first image apply to these images too.)
IP address of the client computer connected to the scanner server
click to start a scan from the scanner server
Stopping a Network Scan in Progress
You can stop a scan in progress from either the client computer or the scanner server. t To cancel a scan from the client computer, click the Cancel button on the Progress bar. t To cancel from the scanner server, click the Cancel button at the bottom of the EPSON Scan Server dialog box. t To break the connection between the client computer and the scanner server, click the Stop button at the bottom of the EPSON Scan Server dialog box. This closes EPSON TWAIN Pro Network on the client computer and allows other client computers to connect to the scanner server.

7 - EPSON GT-10000

Related Documentation
CPD-9639 EPSON GT-10000 Users Guide EPSON GT-10000 Software Reference Guide (html) TM-GT10000 PL-GT10000 EPSON GT-10000 Service Manual EPSON GT-10000 Parts Price List

EPSON GT-10000 - 8

PRODUCT INFORMATION GUIDE

UPDATE

3/7/01
This package provides a new scanner product section to be added to the EPSON Product Information Guide. The table of contents of this section is listed below.

EPSON GT-10000+

TABLE OF CONTENTS
Scanner Parts.... EPSON GT-10000+ - 1 Scanner Specifications... EPSON GT-10000+ - 1 Configuration.... EPSON GT-10000+ - 3 Optional Automatic Document Feeder (B813212) Specifications.. EPSON GT-10000+ - 3 Optional IEEE 1394 Scanner Interface Card (B808342) Specifications.. EPSON GT-10000+ - 3 Lights and Buttons..... EPSON GT-10000+ - 4 Transporting the Scanner... EPSON GT-10000+ - 5 Scanning with EPSON TWAIN Pro... EPSON GT-10000+ - 5 Using a Network Scanner... EPSON GT-10000+ - 6 Related Documentation.... EPSON GT-10000+ - 7
EPSON GT-10000+ Scanner Parts Scanner Specifications
Scanner type: Photoelectric device: Effective pixels: Document size: Flatbed, color Color CCD line sensor 7020 dots 10200 pixels at 600 dpi, 100% 11.7 17.0 inches (mm) (the reading area can be specified from your software) 600 dpi main 2400 dpi sub with MicroStep Drive technology
document cover carriage (at home position) document table

Scanning resolution:

control panel (see page 4)
Maximum resolution with interpolation: dpi Output resolution: Color separation: 50 to 4800 dpi (1-dpi increments) RGB color filters on CCD Monochrome: 1-pass scanning Color byte sequence: 1-pass scanning (R, G, B) Color line sequence: 1-pass scanning (R, G, B) 50 to 200% in 1% increments 36 bits input; 24 bits output (color) 12 bits input; 8 bits output (grayscale)

transportation lock

] Start button

SCSI ID dial

IEEE 1394 optional interface slot

Reading sequence:

Zoom: Image data: Scanning speed (600 dpi draft mode):
SCSI interfaces AC inlet ADF interface

SCSI terminator switch

Color: 4.0 msec/line (approx.) Grayscale: 4.0 msec/line (approx.) Line art: 1.4 msec/line (approx.) 7 levels Fixed threshold with Text Enhancement Technology (TET) enabled AAS (Auto Area Segmentation) Enable/disable selectable 3 halftoning modes (A, B, and C) 4 dither patterns (A, B, C, and D) for bi-level and quad-level data (2 downloadable dither patterns) 2 user-defined dither patterns (A, B)
Brightness: Line art settings: Halftoning process:

EPSON GT-10000+ - 1

Gamma correction: Humidity (without condensation): Operating: 10 to 80% Storage: 10 to 85% Operating conditions: Ordinary office or home conditions; avoid dust, direct sunlight, or strong light
2 types for CRT display 3 types for printer 1 user-defined table 1 type for CRT display 3 types for printer output (available in color byte sequence mode and color line sequence mode) 1 type user-defined ESC/I B7 SCSI 2 (two 50-pin half pitch [high density] connectors) IEEE 1394 serial bus interface (optional) Automatic Document Feeder (ADF) IEEE 1394 serial bus interface Opaque documents with smooth surfaces Xenon fluorescent lamp Main unit MCBF: 100,000 cycles of carriage movements Width: 25.8 inches (656 mm) Depth: 18.0 inches (458 mm) Height: 6.9 inches (176 mm) Approximately 46.3 lb (21 kg)

Color correction:

Safety Approvals
Safety standards: UL 1950 with D3 CSA C22.2 No. 950 EN60950 (VDE) IEC950 (ROSTEST, PSB) FCC part 15 subpart B class B CSA C108.8 class B AS/NZS3548 class B CISPR Pub22 class B CNS13438 class B
Command level: Interface:
Options: Supported documents: Light source: Reliability: Dimensions:

CE marking

Low Voltage Directive 73/23/EEC: EN60950 EMC Directive: 89/336/EEC: EN 55022 Class B EN 61000-3-2 EN 61000-3-3 EN 50082-1 IEC 60801-2 IEC 60801-3 IEC 60801-4

Weight:

Electrical
Input voltage range: Rated frequency: Input frequency: Rated current: Power consumption: 100 to 120 VAC 220 to 240 VAC; universal auto-switching 50 to 60 Hz 49.5 to 60.5 Hz 100 to 120 VAC: 1.2 A 220 to 240 VAC: 0.7 A Approximately 50 W (without ADF) Approximately 55 W (with ADF) Functions:

SCSI Interface

Interface type: ANSI X3T9.2/375R Revision 10L (SCSI 2) BUS FREE phase ARBITRATION phase SELECTION/RESELECTION phase COMMAND phase (the Logical Unit Number is fixed at 0 and the Command Link Function is not supported) DATA phase DATA IN phase DATA OUT phase STATUS phase MESSAGE phase MESSAGE IN phase MESSAGE OUT phase ATTENTION condition RESET condition TTL compatible

Environmental

Temperature: Operating: 41 to 95 F (5 to 35 C); 50 to 89 F (10 to 32 C) when using ADF Storage: 13 to 140 F (25 to 60 C) Logic level:

2 - EPSON GT-10000+

Electrical standard: (SCSI 2) ID setting: Terminator: Connector type:
ANSI X3T9.2/375R Revision 10L Selectable from 0 to 7 (factory setting: 2) Internal terminator selectable (enable/ disable) Two half-pitch (high density), 50-pin connectors
Optional Automatic Document Feeder (B813212) Specifications

General

Paper input/ output: Paper quantity: Load face-up; eject face-down 100 pages (80 g/m2 paper, maximum total thickness under 0.48 inches [12 mm]) 100,000 sheets (load/eject MCBF) 10 ppm (monochrome, draft mode at 200 dpi) Width: 23.8 inches (606 mm) Depth: 19.2 inches (488 mm) Height: 5.3 inches (134 mm) Approximately 28.7 lb (13 kg)
Connector pin arrangement:

Speed:

Dimensions:

Initialization methods

Scanner is turned on or receives a SCSI Reset signal from the SCSI interface (hardware initialization). Scanner receives a SCSI Bus Device message or an Esc @ command from the software (software initialization). Weight:
Input voltage: 22.8 to 25.2 VDC 4.75 to 5.25 VDC 24 V: 1.5 A 5 V: 0.4 A

Configuration

System Requirements
IBM compatible PC with Pentium equivalent or higher processor, 64 MB RAM recommended SCSI: IEEE 1394: ASPI-compliant compatible Fast SCSI, Ultra or Ultra 2 SCSI PCI card IEEE 1394 port equipped PC systems or PCI IEEE 1394 card (OHCI compliant) with Windows 2000 or Me

Input current:

Optional IEEE 1394 Scanner Interface Card (B808342) Specifications
Interface type: Data transfer method: Synchronization method: Encoding/ decoding: Logic level: Compatible connectors: Power class: IEEE 1394-1995 compatible Half-duplex Data/Strobe differential serial Clock synchronization with DS-Link DS-Link 3.3 V IEEE 1394-1995 compatible Power class code 100 No power supply from external sources Fitted with a repeat function with bus power

Operating Systems Supported
Windows 95, 98, 2000, Me, or NT 4.0 (with SP4)

Software Included

EPSON TWAIN Pro Scanner Driver, version 2.0 EPSON TWAIN Pro Network Scanner Driver, version 2.0 EPSON Scan Server, version 1.21E Pixel Translations ISIS Driver, version 1.4.10101.04003 Adobe PhotoDeluxe Business Edition, version 1.0 Xerox TextBridge Pro OCR, version 8.0 NewSoft Presto! PageManager, version 4.20.09

EPSON GT-10000+ - 3

Temperature: Operating: 41 to 95 F (5 to 35 C) Standby: 13 to 140 F (25 to 60 C)

Scanner indicator lights

Light OPERATE READY Light status On On Flashing ERROR On Flashing Red Color Green Green Scanner status Scanner is on. Ready to scan images. Scanning in progress. An error has occurred. See Error conditions table below.
Humidity (without condensation): Operating: 10 to 80% Standby: 10 to 85%
Connector pin assignments
Pin number Signal name VP VG TPB TPB TPA TPA Function Cable power supply Cable ground Strobe during receipt, data during transmission (differential pair) Data during receipt, strobe during transmission (differential pair)

Scanner buttons

Button Function Turns the scanner on and off. Initializes the scanner. Automatically launches a ] Start button-compatible application. You must set up your scanner software and a compatible application to use this feature with any application other than Presto! PageManager. If you installed Presto! PageManager, its automatically assigned to the ] Start button. You can set up Presto! PageManager to scan your image automatically and send it directly to another application or a peripheral device, such as a printer.

P OPERATE

] Start

Lights and Buttons

The scanner has three indicator lights and two buttons on its control panel. A ] Start button is located beside the document table. Light status and button functions are described in the tables that follow.
RESET button OPERATE button

Flashing

Error conditions
ERROR light On READY light On Error type Command error: The scanner has received incorrect commands from the scanning software. Try rescanning. Interface error: Make sure the scanner is securely connected to the computer, and then turn the scanner off and back on again. Fatal error: Make sure the transportation lock is released, and then turn the scanner off and back on again. Option error: Theres a problem with the ADF unit. Make sure the ADF is flat against the document table. Make sure it is securely connected to the ADF connector at the back of the scanner. Finally, make sure the ADF isnt out of paper and doesnt have a paper jam.

ERROR light

OPERATE light READY light

Off Off

4 - EPSON GT-10000+
You cant select EPSON TWAIN Pro as your scanner source if youre using a network scanner and EPSON Scan Server is running. EPSON Scan Server disables EPSON TWAIN Pro.

Transporting the Scanner

When you transport the scanner a long distance or store it for an extended time, follow these steps to secure the carriage: 1. Make sure the transportation lock on the side of the scanner is in the unlocked position. 2. If youre using the automatic document feeder, remove it and replace the scanner cover. 3. Turn on the scanner and wait until the carriage moves to the home position (toward the left of the scanner). Then turn off the scanner.
If the scanner is inoperable, the carriage may not automatically return to the home position. If it doesnt, raise the right side of the scanner and hold it up until the carriage comes to rest at the left side. Then turn the transportation lock to the locked position.
3. Open your scanner driver. In PhotoDeluxe, do one of the following: t Click the Get & Fix Photo button. Click the Get Photo tab, then click the Scanners button. Click the 1 Mode tab, then click the Custom button. t Choose File, Open Special, then select Scan Photo.
The command you choose from the File menu depends on the host application. With some applications, you might choose Acquire or Select Source instead of Open Special.
The EPSON TWAIN Pro main window appears.
4. Turn the transportation lock to the locked position.

locked position

Scanning with EPSON TWAIN Pro
Here is a brief overview of the scanning steps using EPSON TWAIN Pro (or EPSON TWAIN Pro Network). 1. Open your host application (for example, PhotoDeluxe Business Edition). 2. Select your scanner source. (Unless you change your source, you need to do this step only once.) For example, if youre using PhotoDeluxe Business Edition as your host application, click the Get & Fix Photo button. Click the Get Photo tab, then click the arrow below the Scanners button. Select EPSON TWAIN Pro and click OK. If youre accessing a network scanner connected to another computer, select EPSON TWAIN Pro Network as your input source and click OK.

click to display a preview of the image

click to start scanning

4. Choose the Document Source, Image Type, and Destination. For example, if youre scanning a photograph to print, select Flatbed as your Document Source, 24-bit Color [Std] as your Image Type, and EPSON Stylus Printer [Photo] as the Destination, if youre sending the scanned image to an EPSON Inkjet printer. If youre using the optional automatic document feeder, select either ADF - Single-sided or ADF - Double-sided as your Document Source.

EPSON GT-10000+ - 5

5. Click the Preview button. You see a preview of your scan in the window that opens.

Using a Network Scanner

Network scanning involves the following steps: t Connect the scanner to the scanner server. t Turn on the scanner and scanner server and start EPSON Scan Server.
Auto Locate button Auto Exposure button Color Adjustment button
t Place your first image on the document table (or in the automatic document feeder). t From the client computer, start the host application, then start EPSON TWAIN Pro Network to establish a connection to the scanner server. Only one client computer at a time can access the scanner server. t Choose the Image Type, Resolution, and other settings you want for your scan. t Start the scan. Although this can be done from EPSON TWAIN Pro Network on the client computer, it may be more convenient to press the scanners ] Start button or to start the scan from the scanner server. Then you can scan several images with a single trip to the scanner. t If you want to scan more than one image, place your second image on the document table and press the scanners ] Start button again. Repeat this step for every image you want to scan. (The settings you chose for the first image apply to these images too.) t When you return to the client computer, your scanned images appear in the host applications window. Close EPSON TWAIN Pro Network to end your connection to the scanner server and allow other client computers to use the scanner.
Some applications automatically close the client computers connection to the scanner server when you press the ] Start button. You cant scan multiple images if youre using these applications.
6. Choose your scan settings.
Auto Locate button to automatically define Click the the scan area around the edges of your image. You can also adjust the scan area by positioning the mouse pointer over the dotted line around the marquees edge and dragging the box to resize the marquee. Color Adjustment button and use the Gray Click the Balance Intensity feature if you need to remove color cast from your image. Auto Exposure button to automatically set Click the the highlight and shadow exposure.
Generally its a good idea to use the Auto Exposure button to obtain the best settings for your scan.

Starting a Network Scan

7. When youve finished making adjustments, click the Scan button. The READY light on the front of the scanner flickers while its scanning. In a few moments, a scanned image is imported into your host applications window. Then click Close to close the EPSON TWAIN Pro or EPSON TWAIN Pro Network window and return to your application. You can start a scan on your network scanner in several ways: t You can start EPSON TWAIN Pro Network on the client computer, make your scan settings, and click the Scan button on the EPSON TWAIN Pro Network main window. The scanned image is imported into your host application window. t You can press the ] Start button on the scanner to send the scanned image to the client computer that is currently connected to the scanner server.

6 - EPSON GT-10000+

t You can click the Start button on the EPSON Scan Server dialog box to send the scanned image to the client computer currently connected to the scanner server.

Related Documentation

CPD-11730 CPD-11731 EPSON GT-10000+ Users Guide EPSON GT-10000+ Software Reference Guide (html) EPSON GT-10000/GT-10000+ Service Manual EPSON GT-10000+ Parts Price List
IP address of the client computer connected to the scanner server

TM-GT10000/+ PL-GT10000+

click to start a scan from the scanner server
Stopping a Network Scan in Progress
You can stop a scan in progress from either the client computer or the scanner server. t To cancel a scan from the client computer, click the Cancel button on the Progress bar. t To cancel from the scanner server, click the Cancel button at the bottom of the EPSON Scan Server dialog box. t To break the connection between the client computer and the scanner server, click the Stop button at the bottom of the EPSON Scan Server dialog box. This closes EPSON TWAIN Pro Network on the client computer and allows other client computers to connect to the scanner server.

EPSON GT-10000+ - 7

8 - EPSON GT-10000+