00_BGMX_Cover_NEW.fm Page 1 Tuesday, April 7, 2009 12:06 PM
Owners Guide Gua de usario Notice dutilisation
2009 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM314136 Rev.02

SoundDock 10

digital music system
Big_Max_OG.book Page ii Thursday, April 16, 2009 1:22 PM

TAB 8, 16

TAB 7, 15

TAB 6, 14

TAB 5, 13

TAB 4, 12

TAB 3, 11

TAB 2, 10

English

SAFETY INFORMATION

Please read this owners guide
Please take the time to follow the instructions in this owners guide carefully. It will help you set up and operate your system properly and enjoy its advanced features. Please save this owners guide for future reference.

CAUTIONS:

WARNINGS:
To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture. To prevent electric shock, match the wide blade of the line cord plug to the wide slot of the AC (mains) receptacle. Insert fully. Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on or near the apparatus. As with any electronic product, use care not to spill liquids into any part of the system. Liquids can cause a failure and/or a fire hazard. Do not place any naked flame sources, such as lighted candles, on or near the apparatus. Keep the remote control battery away from children. It may cause a fire or chemical burn if mishandled. Do not recharge, disassemble, heat above 100C (212F), or incinerate. Dispose of used batteries promptly. Replace only with a battery of the correct type and model number. Danger of explosion if battery is incorrectly replaced. Replace only with Duracell, Eveready, Energizer, Maxell, Toshiba, or Shun Wo CR2032 or DL2032 3-volt lithium battery. Contains small parts that may be a choking hazard. Not suitable for children under age 3. The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle alerts the user to the presence of important operating and maintenance instructions in this owners guide.

Notes:

The product label is located on the back of the product. Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable. This product must be used indoors. It is neither designed nor tested for use outdoors, in recreation vehicles, or on boats. Make no modifications to the system or accessories. Unauthorized alterations may compromise safety, regulatory compliance, and system performance.
Please dispose of used batteries properly, following any local regulations. Do not incinerate.
This product conforms to the EMC Directive 2004/108/EC and to the Low Voltage Directive 2006/95/EC. The complete Declarations of Conformity can be found at www.Bose.com/static/compliance/ index.html.

Class B emissions

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations (Canada only). If applicable, the radio communication device incorporated into this apparatus meets all requirements of the Industry Canada standard RSS-310 (Canada only).
Big_Max_OG.book Page iii Thursday, April 16, 2009 1:22 PM
IMPORTANT SAFETY INSTRUCTIONS
1. 2. 3. 4. 5. 6. 7. Read these instructions for all components before using this product. Keep these instructions for future reference. Heed all warnings on the product and in the owners guide. Follow all instructions. Do not use this apparatus near water or moisture Do not use this product 13. To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience receptacles. 14. Do not let objects or liquids enter the product as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock.
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or anywhere else that water is present. Clean only with a dry cloth and as directed by Bose Corporation. Unplug this product from the wall outlet before cleaning.

15. See product enclosure for safety related markings. 16. Use proper power sources Plug the product into a proper power source, as
described in the operating instructions or as marked on the product.
protect it from overheating, put the product in a position and location that will not interfere with its proper ventilation. For example, do not place the product on a bed, sofa, or similar surface that may block the ventilation openings. Do not put it in a built-in system, such as a bookcase or a cabinet that may keep air from flowing through its ventilation openings.
Do not block any ventilation openings. Install in accordance with the manufacturers instructions To ensure reliable operation of the product and to
Information about products that generate electrical noise

U.S.A. only

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes to this device not expressly approved by Bose Corporation may void the users authority to operate this device.
Do not install near any heat sources, such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Unplug this apparatus during lightning storms or when unused for long periods of time to prevent damage to this product. 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way: such as power supply cord or plug is damaged; liquid has been spilled or objects have fallen into the apparatus; the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped Do not

attempt to service this product yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Bose to be referred to an authorized service center near you.

Canada

This Class B digital apparatus complies with the Canadian ICES-003 Class B specification.
Big_Max_OG.book Page iv Thursday, April 16, 2009 1:22 PM
SoundDock and the distinctive design of the SoundDock 10 system are registered trademarks of Bose Corporation in the U.S. and other countries. iPod is a trademark of Apple Inc., registered in the U.S. and other countries. All other marks are registered trademarks and trademarks of Bose Corporation. iPhone is a trademark of Apple Inc. All otehr marks are property of Bose Corporation.

For your records

Serial number: ____________________________________________________ Purchase date: ___________________________________________________ Dealer name: _____________________________________________________ Dealer phone: ____________________________________________________ Please keep your sales receipt with this owners guide.
Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Works with iPhone means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Bose Corporation is under license. Other trademarks and trade names are those of their respective owners.
Big_Max_OG.book Page 1 Thursday, April 16, 2009 1:22 PM
SOUNDDOCK 10 DIGITAL MUSIC SYSTEM Introduction
Thank you for purchasing the SoundDock 10 digital music system. Offering a high-quality, room-filling sound, the SoundDock 10 digital music system can easily serve as the primary digital music system in your home. Outstanding features: Proprietary acoustic design delivers full, rich sound Remote controls basic system functions including source selection Auxiliary input allows use with other audio devices Compatible with the iPhone and most iPod models, including the iPod touch and any iPod featuring a click wheel, including nano, mini, photo, video and classic models. Charges your device while it is docked Provides video output connection for a TV or monitor Available Bluetooth dock accessory
SoundDock 10 digital music system AC power cord Remote control

Unpacking

Check the carton for all the parts shown. Save the carton and packing materials, which provide the safest way to transport this product. If any part of the product appears to be damaged, do not attempt to use it. Contact your authorized Bose dealer immediately or call Bose Customer Service. Refer to the address list enclosed in the carton for contact information.
WARNING: To avoid danger of suffocation, keep plastic bags out of the reach of children. Now is a good time to find the serial number on the back of your SoundDock 10 system and record it on the previous page. 1
Big_Max_OG.book Page 2 Thursday, April 16, 2009 1:22 PM
SOUNDDOCK 10 DIGITAL MUSIC SYSTEM

Setting up your system

1. Place your SoundDock 10 digital music system on a flat, stable surface. 2. Plug the small end of the AC power cord into the AC power connector on the back of the unit. 3. Plug the other end into a live AC (mains) outlet. After you hear two short tones from your SoundDock 10 system, it is ready to use.
CAUTION: Do not cover the ventilation openings of the product. The slots on the top provide ventilation for the built-in electronic circuitry and shall not be blocked. Note: When handling the SoundDock 10 system, the front
structure containing the iPod/iPhone dock may feel loose. This is normal. This part of the system is intentionally designed to prevent speaker vibration from interfering with the operation of your iPod/iPhone.

System on/off control

You can turn on your SoundDock 10 system in any of the following three ways: Dock a device. Press any key except OFF on the Bose remote. Press any key on the docked device.
To turn off the SoundDock 10 system, do either one of the following: Press OFF on the SoundDock 10 remote. Remove the docked device.
Note: The tonal quality of your SoundDock 10 system will vary
with placement. For example, moving the system toward a corner will increase bass response; moving it away from the corner will decrease bass response.
Big_Max_OG.book Page 3 Thursday, April 16, 2009 1:22 PM
Listening to a docked device
1. Insert your iPod or iPhone into the dock. The dock indicator glows on the front panel.
Dock Press to select the docked device. Off Press to turn off the system. Play/Pause Press to play or pause the current track on the docked device. Volume +/ Press to increase (+) or decrease () the volume. Press and hold for faster adjustment. Playlist select Press to select the next ( ) or previous ( ) playlist. Skip forward Press once to skip to the next track. Press and hold to quickly scan forward through a track. Skip backward Press once to skip to the beginning of the current track. Press twice to skip to the beginning of the previous track. Press and hold to quickly scan backward through a track.

Dock indicator

2. Use the Bose remote to control system functions. Note: Your SoundDock 10 digital music system charges your
iPod/iPhone whenever it is docked.
Note: Your SoundDock 10 digital music system comes with a universal dock adapter that can accommodate most iPod models. If you prefer to use the adapter that came with your iPod, see Changing the dock adapter on page 6.
Big_Max_OG.book Page 4 Thursday, April 16, 2009 1:22 PM
Listening to other devices
You can connect the audio output of a PC, CD player, TV, MP3 player, or other type of audio device to the AUX IN connector. The AUX IN connector accepts a 3.5mm stereo cable plug. 1. Using the appropriate stereo cable, connect your audio device to the AUX IN connector.
Note: A device must be plugged into the AUX IN connector in
order to select the AUX source.
2. Press AUX on the Bose remote. The AUX IN indicator glows on the front panel.

AUX IN indicator

Laptop PC
3. Turn on the audio device and start playing music. 4. Set the volume of the device to near maximum. Note: The SoundDock 10 system is designed to provide the
3.5mm stereo cable (not supplied) best audio performance without any additional audio effects. Make sure all audio effects are turned off in the connected device.
Big_Max_OG.book Page 5 Thursday, April 16, 2009 1:22 PM
SOUNDDOCK 10 DIGITAL MUSIC SYSTEM 5. Use the Bose remote to increase or decrease the system volume.
Off Press to turn off the system. AUX Press to select the AUX IN source. Volume +/ Press to increase (+) or decrease () the volume. Press and hold for faster adjustment.

Using the video output

When playing a docked iPhone or iPod with video capability, the VIDEO OUT connector provides a composite video output signal that can be viewed on a TV or computer monitor. To view this video output on your TV or monitor, connect the VIDEO OUT to a video input using a standard composite video cable. Be sure to select the correct video input on your TV.
Composite video cable (not supplied)
Notes: The Bose remote will not control devices connected to AUX IN. A docked iPod/iPhone will continue charging while you listen to a device connected to AUX IN. 5
Big_Max_OG.book Page 6 Thursday, April 16, 2009 1:22 PM
Changing the dock adapter

The SoundDock 10 digital music system is ready for use with an iPhone or a variety of iPod models. If you prefer to use the dock adapter included with your iPod: 1. Make sure the power cord is disconnected. 2. Lift up the back edge of the adapter and remove it from the dock. You may need to insert a thin, non-metallic utensil into the slot to provide the required leverage to lift the back edge.

Care and maintenance

Periodic maintaining may include cleaning your product and replacing the remote control batteries.

Cleaning

To clean the exterior surface of your product, you can wipe it using a soft, dry cloth. You can also lightly vacuum the grille. Do not use solvents, chemicals, or sprays. Do not allow liquids to spill or objects to drop into any openings.
Replacing the remote control batteries
When the remote stops operating or its range seems reduced, it is time to change the remote battery. 1. Using a coin, turn the battery cover slightly counterclockwise.
Big_Max_OG.book Page 7 Thursday, April 16, 2009 1:22 PM
SOUNDDOCK 10 DIGITAL MUSIC SYSTEM 2. Remove the used battery and insert the new one (CR2032 or DL2032). Refer to page ii for battery information and safety instructions. Be sure the battery is flat side up, with the positive (+) symbol in view.

UPDATE connector

The UPDATE connector on the back of your SoundDock 10 system is for potential software updates, only.

UPDATE

3. Reseat the cover and turn it clockwise until it locks into place.

Troubleshooting

The following troubleshooting table should help solve operating problems with your SoundDock 10 system. However, before using the table, do the following: Remove your iPod/iPhone from the dock and check for obstructions on the dock connector and on your iPod/iPhone. Then firmly reseat it in the dock. Make sure you have the latest software on your iPod/ iPhone.
iPod/iPhone compatibility
If you have questions regarding the compatibility of your iPod/iPhone with the SoundDock 10 digital music system, see www.Bose.com for the most current compatibility information.
Big_Max_OG.book Page 8 Thursday, April 16, 2009 1:22 PM

Problem

I do not hear any sound from the SoundDock 10 system.

What to do

Make sure the power cord is properly connected on the back of the SoundDock 10 system and that the system is plugged into a live AC outlet. Press the source button (dock or AUX) on the remote for the source you are using. Press the Play/Pause button on the remote control. Increase the system volume. If listening to a device connected to AUX IN, increase the volume on the device. Remove your iPod/iPhone from the dock, wait 5 seconds, then reseat it. Unplug the power cable for 1 minute, then plug it back in to reset the system. Make sure the power cord is properly connected on the back of the unit. Make sure the system is plugged into a live AC outlet. Make sure that you have created playlists on your iPod/iPhone.

My iPod/iPhone is not charging. I cannot navigate the playlists on my iPod/ iPhone. My iPod/iPhone does not respond to the remote control.
Make sure there is a clear path between the remote and the system. Using a clean, dry cloth, wipe the small lens on the front end of the remote. Try the remote from a different location. You may be experiencing interference from bright room lights or sunlight. Remove your iPod/iPhone from the dock, wait 5 seconds, then reseat it. Make sure the remote battery is installed correctly or replace it if it is old (refer to page 6). Unplug the power cable for 1 minute, then plug it back in to reset the system. Contact Bose Customer Service.
My system does not respond to any controls.
Big_Max_OG.book Page 9 Thursday, April 16, 2009 1:22 PM

Customer service

For questions about the SoundDock 10 digital music system, contact your local Bose dealer. To contact Bose directly, see the address list included in the carton.
3. Label and ship the product, freight prepaid, to the address provided by the authorized service facility. 4. Place any necessary return authorization number prominently on the outside of the carton. Cartons not bearing a return authorization number, where required, will be refused.

Limited warranty

Your SoundDock 10 digital music system is covered by a limited transferable warranty. Details of the limited warranty are provided on the product registration card that is included in the carton. Please refer to the card for instructions on how to register. Failure to register will not affect your limited warranty rights.

Technical Information

Input power rating
U.S.A./Canada: 100-120V International: 220-240V 100-240V 50/60Hz, 150W 50/60Hz, 150W 50/60Hz, 150W
What you must do to obtain limited warranty service
Return product, with proof of purchase from an authorized Bose dealer, using the following procedures: 1. Visit http://global.Bose.com or contact your local authorized Bose dealer to identify the location of the nearest authorized Bose service facility. 2. Contact the authorized service facility for specific return and shipping instructions.

SOUNDDOCK 10
DIGITAL MUSIC SYSTEM Bluetooth Dock

Owners Guide

English

Safety information

Please read this owners guide
Please take the time to follow the instructions in this owners guide carefully. It will help you set up and operate your system properly and enjoy its advanced features. Please save this owners guide for future reference.

WARNINGS:

To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture. Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any part of the system. Liquids can cause a failure and/or a fire hazard. Do not place any naked flame sources, such as lighted candles, on or near the apparatus. Contains small parts which may be a choking hazard. Not suitable for children under age 3.

Notes:

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations (Canada only). If applicable, the radio communication device incorporated into this apparatus meets all requirements of the Industry Canada standard RSS-310 (Canada only). The product must be used indoors. It is neither designed nor tested for use outdoors, in recreation vehicles, or on boats. This product conforms to the EMC Directive 2004/108/EC and to the Low Voltage Directive 2006/95/EC. The complete Declaration of Conformity can be found at www.Bose.com/static/compliance/index.html.
Compliance with FCC rules (U.S.A. only)
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Proper connections must be used for connection to a host computer and/or peripherals in order to meet FCC emission limits.

Overview

The Bose SoundDock 10 Bluetooth dock adds Bluetooth wireless technology capability to your SoundDock 10 digital music system. After installing this accessory, you can listen to your stereo Bluetooth music phone with high-quality, room-filling sound. To experience the intended performance, your stereo Bluetooth music phone must support the Bluetooth Advanced Audio Distribution Profile (A2DP).
Installing the Bluetooth dock
1. Disconnect the SoundDock 10 power cord from the AC outlet. 2. Lift up the back edge of the universal dock adapter (A) and remove it from the dock. You may need to insert a thin non-metallic utensil into the slot to provide the required leverage to lift the back edge. A B C
3. Press the dock release button (B) on the right and lift up (C) the right side of the dock to remove it.
4. Slide the left end of the Bluetooth dock into the dock opening (A). A B
5. Press down on the right side of the dock until it locks in place (B).
Making the first connection
1. Plug the power cord of the SoundDock 10 digital music system into an AC receptacle. 2. Wait until the Bluetooth light starts flashing, meaning that the Bluetooth dock is in discoverable mode.
NOTE: The dock stays in discoverable mode (for as long as 30 minutes) until you connect your stereo Bluetooth music phone to it.
Bluetooth light (flashing = discoverable mode)
3. Bring your stereo Bluetooth music phone close to the SoundDock 10 system. 4. Turn on the Bluetooth feature in your music phone. For details on using this feature, refer to the owners guide for your phone. 5. In the list of found Bluetooth devices, find Bose SoundDock 10 and select it. 6. If prompted, enter the Bose SoundDock 10 passkey: 0000. 7. When your music phone confirms it is connected, check that the Bluetooth light stops flashing and remains on. If your stereo Bluetooth music phone becomes disconnected because it is out of range, the dock automatically tries to reconnect with it when you bring it within range again. If the SoundDock 10 system can not restore a connection within five minutes it turns off. To disconnect, press Off on the Bose SoundDock 10 remote or use the disconnect command in your phone. To reconnect when your system is off, press any remote key except Off or AUX to turn on the system. The SoundDock 10 system then automatically tries to connect with the most recently-connected phone.

Connecting with other stereo Bluetooth music phones
After making an initial connection, you can change the connection to another phone by activating the discoverable mode again. However, you can connect to only one phone at a time. 1. Press and hold the Bluetooth button on the dock or the dock button on the remote control until the Bluetooth light starts flashing.

Dock button

Bluetooth button
2. Follow Steps 3-7 on the previous page. For the purpose of automatic reconnection, the SoundDock 10 system remembers the six most recently-connected music phones.

Controlling the volume

Increase the volume of your stereo Bluetooth music phone to near maximum. Then use the Bose SoundDock 10 remote to control the system volume.

Connection quality light

The quality of any wireless connection with the Bluetooth dock can vary. This may affect the quality of the audio heard from your SoundDock 10 system. Connection The connection quality light on the dock quality light (On) tells you the general condition of the wireless connection made between your phone and the Bluetooth dock: Constantly On. No affect on audio quality Blinking. Audio quality may be affected Blinking faster. Audio quality is most likely affected If the audio quality is affected: Move your phone closer to the system or to a different location. Move your phone away from any household device that generates electromagnetic radiation, such as a microwave oven, another Bluetooth device, or a wireless computer network router. Reduce the number of applications running on your phone.

Troubleshooting

If you experience difficulty with your Bluetooth dock, use the following table to try and solve the problem. If the problem still persists, see Contacting customer service on page 11.

Problem What to do

Can not Make sure your SoundDock 10 is connected to AC power. connect Make sure the Bluetooth dock is in discoverable mode (Bluetooth my phone light is flashing). If not, press and hold the Bluetooth button on the to the dock until the Bluetooth light starts flashing. dock Make sure the Bluetooth feature is turned on in your phone. For details, refer to the owners guide for your phone. Move your phone closer to the SoundDock 10. Go to http://owners.bose.com on the Internet and find information on updating your SoundDock 10. No sound Make sure the SoundDock 10 and your phone are turned on. Make sure you have a Bluetooth connection (Bluetooth light is on). Move your phone closer to the SoundDock 10. Turn up the phone volume as high as possible. Turn up the SoundDock 10 volume.
Sound is dropping out or breaking up
Move your phone or SoundDock 10 away from any device that generates electromagnetic radiation, such another Bluetooth device, a microwave oven, or a wireless computer network router. Remove any physical obstruction lying between your phone and the SoundDock 10 system. Reposition your phone and or the SoundDock 10 system.

English Problem What to do
Poor sound quality Move your phone closer to the system or to a different location. Move your phone away from any household device that generates electromagnetic radiation, such as a microwave oven, another Bluetooth device, or a wireless computer network router. Reduce the number of applications running on your phone. Increase the volume on your phone.
Removing the Bluetooth dock
To remove the Bluetooth dock so that you can put the universal dock back in your system: 1. Slide the release latch (A) to the right. A B
2. Lift up the right side (B) of the Bluetooth dock to remove it.
Contacting customer service
For questions about the SoundDock 10 Bluetooth Dock, contact your local Bose dealer. To contact Bose directly, see the address list included with your SoundDock 10 or visit http://owners.Bose.com on the Internet.

Limited warranty

Your SoundDock 10 Bluetooth Dock is covered by a limited transferable warranty. Details of the limited warranty are provided on the product registration card that is included in the carton. Please refer to the card for instructions on how to register. Failure to register will not affect your limited warranty rights.
What you must do to obtain limited warranty service
Return product, with proof of purchase from an authorized Bose dealer, using the following procedures: 1. Visit http://global.Bose.com or contact your local authorized Bose dealer to identify the location of the nearest authorized Bose service facility. 2. Contact the authorized service facility for specific return and shipping instructions.
3. Label and ship the product, freight prepaid, to the address provided by the authorized service facility. 4. Place any necessary return authorization number prominently on the outside of the carton. Cartons not bearing a return authorization number, where required, will be refused.
SoundDock and the distinctive design of the SoundDock 10 system are registered trademarks of Bose Corporation in the U.S. and other countries. All other marks are registered trademarks and trademarks of Bose Corporation. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Bose Corporation is under license. Other trademarks and trade names are those of their respective owners.

2009 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM316536 Rev.00