Internet Game Console Plug-and-Go
Wireless Game Adapter WGE111
Personal Computer Plug-and-Go

What you need

1. Broadband Internet access through a router with an 802.11b or 802.11g wireless access point (built in to the router or separate) without any security features enabled. A computer to run the initial configuration. Connect the Ethernet cable from your WGE111 Wireless Game Adapter (A) to the Ethernet port on your computer (B).
Broadband Internet access through a router with an 802.11b or 802.11g wireless access point (built in to the router or separate) without any security features enabled. Note: If you enabled security features (like WEP, WPA-PSK, SSID broadcast off, MAC filtering, etc.) you need to follow the instructions in the Reference Manual. 1. A network-enabled game console. Connect the Ethernet cable from your WGE111 Wireless Game Adapter (A) to the Ethernet port (B) in the game console.

Start Here

Unpack the box, verify the contents, and follow the instructions below. You can also consult the Reference Manual on the NETGEAR, Inc. Web site at http://kbserver.netgear.com/products/wge111.asp The WGE111 Wireless Game Adapter operates in either Infrastructure or Ad-Hoc mode.

What you do

WGE111 Wireless Game Adapter
Infrastructure mode (labeled Internet) Ad-Hoc mode
Gaming Console or other Ethernet-enabled device

Switch Position

Left position, which is the factory shipped default Right position (must be changed from default left position)

Your System

Access point or wireless router connected to a wired network Small, wireless-only network and all devices have wireless transmitters/ receivers.
Make sure that the switch on the back of the WGE111 is set to the left side (labeled Internet), which corresponds to Infrastructure Mode. Connect the power adapter to the WGE111 and verify the following: The power light goes on.
Make sure that the switch on the back of the WGE111 is set to the left side (labeled Internet), which corresponds to Infrastructure Mode. Connect the power adapter to the WGE111 and verify the following: The power light goes on. The Internet light is lit. The Ethernet light is lit.
The Internet light is lit. The Ethernet light is lit when connected to a powered on networkenabled game console. 4.
If you would like to change the default IP address or access the wireless game adapter Web configuration console, see the Smart Wizard Configuration Assistant section on this card. The default IP address is 192.168.0.202. 4.
Enjoy your Internet gaming!
Smart Wizard Configuration Assistant
You can use the NETGEAR Smart Wizard configuration assistant to change the IP settings of the adapter. Configuring the wireless game adapter to use a fixed or dynamic IP address lets you to access the wireless game adapter configuration from a Web browser. 1. 2. 3. Insert the Resource CD in your CD-ROM drive. Double-click setup.exe if the program does not start automatically. Select Configuration Assistant. The Wireless Game Adapter configuration assistant window shows all the NETGEAR Wireless Game Adapters on the LAN. Select your WGE111 Wireless Game Adapter and click Next. If the password prompt is displayed, type password. Select the Wireless Network to connect to. Click Next. Set the Infrastructure or Ad-Hoc configuration mode configuration. You can fill in both sections and the configuration used will be determined by the physical placement of the switch on the back of the wireless game adapter.
Select the Change Password check box and type the old password for the Wireless Game Adapter. The default password is password. Type a new password and then type it again in the Confirmation box. Click Next. The Wireless Game Adapter Configuration Assistant window shows the TCP/IP settings for the Wireless Game Adapter. a. Change the device name from NETGEARxxxx to a name of your choosing if you like. b. c. If you are going to use a fixed IP address, select Use this IP Address. Enter the IP address, Subnet mask, and Default gateway to match your network. Make your selections and click Next.

Problem

Cannot configure the WGE111 from a browser.

Action

You did not specify the correct wireless game adapter IP address, or there could be a system problem. Remove and reconnect the power to the wireless game adapter. Make sure your computer and the wireless game adapter are in the same subnet. Both IP addresses should start with the same numbers. For example, 192.168.0.x or 192.168.1.x. The subnet masks must match. For example, both should be 255.255.255.0. Enter the correct IP address in the address field of the browser. 192.168.0.202 is the WGE111 default IP address.

4. 5. 6.

The previous settings (if any) and new settings you have configured are displayed. Click Next. 10. The settings you selected are displayed. Click Refresh to update the results. Click Finish to exit.

Technical Support

Thank you for selecting NETGEAR products. Register your product at http://www.NETGEAR.com/register. Registration is required before you can use our telephone support service. Go to http://kbserver.netgear.com/products/WGE111.asp for product updates and Web support. Attention: When you configure the wireless settings of this device please make sure to select the correct country settings. Due to EU law, the country settings must be identical to the country where the device is operating. Important, due to non-harmonized frequencies in the EU, observe these 802.11b restrictions: European standards dictate maximum radiated transmit power of 100 mW EIRP and frequency range of 2.400 ~ 2.4835 GHz. In France, the equipment must be restricted to 2.44654 ~ 2.4835 GHz frequency range and must be restricted to indoor use.

Troubleshooting

If you have trouble setting up your WGE111, check the tips below. You can also consult more extensive troubleshooting procedures in the Reference Manual on the NETGEAR, Inc. Web site at http://kbserver.netgear.com/products/wge111.asp. Be sure to observe the range and placement guidelines published in the Reference Manual. Note: The WGE111 can be used as a wireless game adapter with one machine only and does not support multiple devices. Problem
Wireless light always blinking
The wireless game adapter has not connected to a wireless network. Make sure the WGE111 is within range of the wireless network. Make sure the wireless network security settings and the WGE111 security settings match. There is a network configuration problem. Make sure the wireless network security settings and the WGE111 security settings match. Make sure the computer, adapter, and router IP settings are correct.

a. b. c.

Fill in the Infrastructure settings. If you want to configure Ad-Hoc mode also, select the Ad-hoc Mode check box and configure the Ad-Hoc settings. Click Next.

Wireless light is solid but cannot connect to Internet
2004 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved.

August 2004