Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. 6. Always use the proper needle plate, The wrong plate can cause the needle to break. 7. Do not use bent needles. 8. Do not pull or push fabric while stitching. It may deflect the needle causing it to break. 9. Switch the sewing machine off ("O") when making any adjustments in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, and the like. 10.Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual. 11.Never drop or insert any object into any opening. 12.Do not use outdoors. 13.Do not operate where aerosol spray products are being used or where oxygen is being administered. 14.To disconnect, turn all controls to the off ("O") position, then remove plug from outlet. 15.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 16.The sound pressure level under normal operating conditions is 75dB(A).
DANGER - To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in. 2. Always unplug this appliance from the electric outlet immediately after using and before cleaning. 3. Always unplug before re-lamping. Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area).
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used by or near children. 2. Use this appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual. 3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. 4. Never operate the appliance with any air openings blocked. Keep ventilation openings of the sewing machine and foot controller free from accumulation of lint, dust, and loose cloth. 5. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use only.

Congratulations

As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made. May we recommend that, before you start to use your sewing machine, you discover the many advantages and the ease of operation by going through this instruction book, step by step, seated at your machine. To ensure that you are always provided with the most modern sewing capabilities, the manufacturer reserves the right to change the appearance, design or accessories of this sewing machine when considered necessary.
SINGER IS A REGISTERED TRADEMARK OF THE SINGER COMPANY LIMITED OR ITS AFFILIATES COPYRIGHT 2005 All rights reserved throughout the world.

List of contents

Principal parts of the machine..2/3 Accessories...4 Installing the snap-in sewing table...5 Connecting machine to power source...6 Changing the bulb...7 Two-step presser foot lifter...8 Adjusting presser foot pressure...8 Attaching the presser foot holder..9 Winding the bobbin...10 Inserting the bobbin..11 Inserting and changing needles..12 Threading the upper thread..13 Automatic needle threader (optional)..14 Thread tension...15 Raising the bobbin thread..16 Reverse sewing/ Removing the work/ Cutting the thread.17 Matching needle/ fabric/ thread..18 How to choose your pattern..19 Straight stitch and needle position..20 Zig-zag stitching..21 Blind hem/ Lingerie stitch..22 Sewing on buttons...23 Sew 4-step buttonholes...24 Zippers and piping...25 Mutlti-stitch zig-zag/ Bar tack..26 Free motion darning, stippling...27 Practical stitches...28 Applique and blindstitch applique...29 Quilting functions...30 Mending...31 Stay-stitching....32 Blindstitch applique..33 Traditional pintucks..34 Gathering...35 Couching...36 Trim attachment stitch function..37 Maintenance...38 Trouble shooting guide..39

Principal parts of the machine
1. Thread tension dial 2. Presser foot pressure adjustment 3. Thread take-up lever 4. Thread cutter 5. Presser foot 6. Needle plate 7. Removable sewing table/ accessory storage 8. Reverse sewing lever 9. Bobbin stopper 10. Stitch length dial 11. Pattern selector dial 12. Automatic threader (optional) 9 10
13. Horizontal spool pin 14. Bobbin winder 15. Handwheel 16. Power and light switch 17. Main plug socket 18. Bobbin thread guide 19. Upper thread guide 20. Face plate 21. Handle 22. Presser foot lever 23. Foot speed control 24. Power cord 21 22

Accessories

Standard accessories (1) a. All purpose foot b. Zipper foot c. Buttonhole foot d. Button sewing foot e. L-screwdriver f. Seam ripper/ brush g. Oil bottle h. Pack of needles I. Bobbin (3x) j. Seam guide k. Darning plate l. Spool holder 1 a b c d

006806008

006905008

006909008

006914008
Optional accessories (2) (These 6 accessories are not supplied with this machine; they are however available as special accessories from your local dealer.) m.Satin stitch foot n. Overcasting foot o. Hemmer foot p. Blind hem foot q. Cording foot r. Darning foot

2 m n o

006916008

006803008

006800008

006812008

006804008

006016008

Installing the snap-in sewing table
Keep the snap-in sewing table horizontal, and push it in the direction of the arrow. (1)
1 The inside of the snap-in sewing table can be utilized as an accessory box. To open, lift up at the point of the arrow. (2)
Connecting machine to power source
Connect the machine to a power source as illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2) Attention: Unplug power cord when machine is not in use.
Foot control The foot control pedal regulates the sewing speed. (3) Attention: Consult a qualified electrician if in doubt as to connect machine to power source. Unplug power cord when machine is not in use. The foot control must be used with the appliance by KD-1902 (110-120V area)/ KD-2902 (220-240V area) manufactured by ZHEJIANG FOUNDER MOTOR CORPORATION LTD. (China) Sewing light Press main switch (A) for power and light on " l ". IMPORTANT NOTICE For appliance with a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If it does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way. 1

Polarized attachment plug
Conductor intended 2 to be grounded

Changing the bulb

Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area). - Loosen screw (A) as illustrated. (1) - Remove the face plate (B). - Unscrew the bulb and install a new one (C). (2) - Replace the face plate and tighten screw. Should there be any problem, ask your local dealer for advice. 1
Two-step presser foot lifter
When sewing several layers or thick fabrics, the presser foot can be raised to a high rise position for easy positioning of the work. (A)
Adjusting presser foot pressure
The presser foot pressure of the machine has been pre-set and requires no particular readjustment according to the type of fabric (light-or-heavy weight). However, if you need to adjust the presser foot pressure, turn the presser adjusting screw with a coin. For sewing very thin fabric, loosen the pressure by turning the screw counter counterclockwise, and for heavy fabric, tighten by turning it clockwise.
Attaching the presser foot holder
Raise the presser bar (a). Attach the presser foot shank (b) as illustrated. (1) Attaching the presser foot Lower the presser foot shank (b) until the cut-out (c) is directly above the pin (d). (2) Raise the lever (e). Lower the presser foot shank (b) and the presser foot (f) will engage automatically. Removing the presser foot Raise the presser foot. (3) Raise the lever (e) and the foot disengages. 1 Attaching the seam guide Attach the seam guide (g) in the slot as illustrated. Adjust according to need for hems, pleats, etc. (4)
Attention: Turn power switch to off ("O") when carrying out any of the above operations!

Winding the bobbin

- Place thread and spool holder onto spool pin (1). - For smaller spools of thread place spool holder with small side next to spool (2). - Wind thread anticlockwise around bobbin winder tension discs (3). - Thread bobbin as illustrated and place on spindle (4). - Push bobbin to right (5). - Hold thread end (6). - Step on foot control pedal (7). - Cut thread (8). - Press bobbin to left (9) and remove. Please Note: When the bobbin winder spindle is in "bobbin winding" position, the machine will not sew and the hand wheel will not turn. To start sewing, push the bobbin winder spindle to the left (sewing position). 2 1

Inserting the bobbin

When inserting or removing the bobbin, the needle must be fully raised. - Open the hinged cover (1). - Hold the bobbin case with one hand. Insert the bobbin so that the thread runs in a clockwise direction (arrow) (2). - Pull the thread through the slit and under the finger (3). - Hold the bobbin case by the hinged latch (4). - Insert it into the shuttle (5). Attention: Turn power switch to off ("O") before inserting or removing the bobbin. 1 2
Inserting and changing needles
Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results always use SINGER Brand Needles. Insert the needle as illustrated as follows: A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1) B. The flat side of the shaft should be towards the back. C/D. Insert the needle as far up as it will go.
Attention: Turn power switch to off ("O") before inserting or removing the needle.
Needles must be in perfect condition. (2) Problems can occur with: A. Bent needles B. Blunt needles C. Damaged points
Threading the upper thread
This is a simple operation but it is important to carry out correctly as by not doing so several sewing problems could result. - Start by raising the needle to its highest point (1), and also raise the presser foot to release the tension discs. (2) Note: For safety, it is strongly suggested you turn off the power before threading. - Lift up the spool pin. Place the spool of thread on the holder with the thread coming off the spool as shown. For small thread spools, place small side of spool holder next to spool.(3) - Draw thread from spool through the upper thread guide. (4) - Guide thread around thread guide (5) pulling thread through pretension spring as illustrated. - Thread tension module by leading thread down right channel and up left channel (6). During this process it is helpful to hold the thread between the spool and thread guide (4). - At the top of this movement pass thread from right to left through the slotted eye of the take-up lever and then downwards again. (7) - Now pass thread behind the thin wire needle clamp guide (8) and then down to the needle which should be threaded from front to back. - Pull about 6-8 inches of thread to the rear beyond the needle eye. Trim thread to length with built in thread cutter. (9) Note: If your sewing machine is equipped with the factory installed optional automatic needle threader, instructions for use can be found on page 14. 5
Automatic needle threader (optional)
* The automatic needle threader is a factory installed option. If your machine has this option use the following instructions: - Raise the needle to its highest position. - Press lever (A) down as far as it will go. - The threader automatically swings to the threading position (B). - Pass thread around thread guide (C). - Pass the thread in front of the needle around the hook (D) from bottom to top. - Release lever (A). - Pull the thread through the needle eye. Attention: Turn power switch to off ("O")! 1

C A C B D D A B

Thread tension
Upper thread tension Basic thread tension setting: "4" To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down. A. Normal thread tension for straight stitch sewing. B. Thread tension too loose for straight stitch sewing. Turn dial to higher number. C. Thread tension too tight for straight stitch sewing. Turn dial to lower number. D. Normal thread tension for zig zag and decorative sewing. Correct thread tension is when a small amount of the upper thread appears on the bottom side of fabric. Lower thread tension To test the bobbin thread tension, remove the bobbin case and bobbin and hold it by suspending it by the thread. Jerk it once or twice. If the tension is correct, the thread will unwind by about an inch or two. If the tension is too tight, it does not unwind at all. If the tension is too loose, it will drop too much. To adjust, turn the small screw on the side of the bobbin case. Please note: - Proper setting of tension is important to good sewing. - There is no single tension setting appropriate for all stitch functions, thread or fabric. - A balanced tension (identical stitches both top and bottom) is usually only desirable for straight stitch construction sewing. - 90% of all sewing will be between "3" and "5". - For zig zag and decorative sewing stitch functions, thread tension should generally be less than for straight stitch sewing. - For all decorative sewing you will always obtain a nicer stitch and less fabric puckering when the upper thread appears on the bottom side of your fabric.
Raising the bobbin thread
Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising needle.
Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole (2). Lay both threads to the back under the presser foot. (3)

Reverse sewing

To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches. Release the lever and the machine will sew forwards again. (1)

Removing the work

Turn the handwheel counterclockwise to bring the thread take up lever to its highest position, raise the presser foot and remove work behind the needle and presser foot. (2) 1 2

Cutting the thread

Pull the threads behind the presser foot. Guide the threads to the side of the face plate and into thread cutter (B). Pull threads down to cut. (3)
Matching needle/ fabric/ thread
NEEDLE, FABRIC, THREAD SELECTION GUIDE NEEDLE SIZE 9-11 (70-80) FABRICS THREAD Lightweight fabrics-thin cottons, voile, serge, silk , muslin, Light-duty thread in cotton, nylon ,polyester or Qiana, interlocks, cotton knits, tricots, jerseys, crepes, woven cotton wrapped polyester. polyester, shirt & blouse fabrics. Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, Most threads sold are medium size and suitable double knits, lightweight woollens. for these fabrics and needle sizes. Use Medium weight fabrics-cotton duck, woolen, heavier knits, polyester threads on synthetic materials and cotton on natural woven fabrics for best results. terrycloth, denims. Always use the same thread on top and bottom. Heavyweight fabrics-canvas, woolens, outdoor tent and quilted fabrics, denims, upholstery material (light to medium). Heavy woollens, overcoat fabrics, upholstery fabrics, some Heavy duty thread, carpet thread. (Use heavy leathers and vinyls. foot pressure-large numbers.)

11-14 (80-90) 14 (90) 16 (100) 18 (110)
IMPORTANT: Match needle size to thread size and weight of fabric. NEEDLE, FABRIC SELECTION NEEDLES SINGER 2020 SINGER 2045 SINGER SINGER EXPLANATION TYPE OF FABRIC Standard sharp needles. Sizes range Natural woven fabrics-wool, cotton, silk, etc. Qiana. Not recommended for thin to large. 9 (70) to 18 (110). double knits. Semi-ball point needle, scarfed. 9 (70) to Natural and synthetic woven fabrics, polyester blends. Knits-polyesters, 18 (110). interlocks, tricot, single and double knits. Also sweater knits, Lycra, swimsuit fabric, elastic. Twin Needle. Leather needles. 12 (80) to 18 (110) Woven fabrics and knits. Leather, vinyl, upholstery. (Leaves smaller hole than standard large needle.)
Note twin needle: 1. Twin needles, can be purchased for utility and decorative work. 2. When sewing with twin needles, the stitch width dial should be set at less than "3". 3. For best sewing results always use genuine SINGER needles. 4. Replace needle often (approximately every other garment ) and/ or at first thread breakage or skipped stitches.
How to choose your pattern
For center needle straight stitch select pattern " " with pattern selector dial. Adjust the stitch length with the stitch length dial. You may choose left needle position, by selecting pattern " ". For zigzag stitch, select pattern " " with pattern selector dial. Adjust the stitch length according to the fabric being used. To obtain any of the other patterns shown on the stitch selection panel, select the stitch with the pattern selector dial. Adjust the stitch length with the stitch length dial.
a. Reverse sewing lever b. Stitch length dial c. Pattern selector dial
Straight stitching and needle position
Turn the stitch selection dial so that the pointer is set to the straight stitch position. Choose your needle position, from center needle position or right needle position. Generally speaking, the thicker the fabric, thread and needle, the longer the stitch should be. For a fine stitch set length at "1" or "2". For gathering set to straight stitch, with stitch length at "4". Do 2 rows of stitching of an inch apart. Remove from machine, hold bobbin thread and gather fabric to desired fullness.

Topstitching Topstitching is used to embellish a variety of projects. Sew 1/4 of an inch from the edge of your garment or seam to topstitch. Turn the stitch selection dial so that the pointer is set to the straight stitch position. Choose center needle position. For topstitching variable stitch length can be used. Use the all purpose foot to perform this function.

Zig-zag stitching

Turn the pattern selector dial to " ". (1) Function of stitch length dial while zigzaging The density of zigzag stitches increase as the setting of stitch length dial approaches "0". Neat zigzag stitches are usually achieved at "2.5" or below. Dense zigzag stitches (close together) are referred to as a satin stitch. (2)
Blind hem/ Lingerie stitch
For hems, curtains, trousers, skirts, etc. Blind hem for stretch fabrics. Blind hem/ lingerie for firm fabrics. Reverse blind hem/ lingerie for firm fabrics. Note: It takes practice to sew blind hems. Always make a sewing test first. Turn up the hem to the desired width and press. Fold back (as shown in Fig. 1) against the right side of the fabric with the top edge of the hem extending about 5 mm. (1/5") to the right side of the folded fabric. Start to sew slowly on the fold, making sure the needle touches slightly the folded top to catch one or two fabric threads (2). Unfold the fabric when hemming is completed and press.

Sewing on buttons

Install the darning plate. (1) Change presser foot to button sewing foot (2). Position the work under the foot. Place the button in the desired position and lower the foot. Set the pattern selector knob on " " and sew a few securing stitches. Select one of the two narrow zig zag patterns according to the distance between the two holes of the button. Turn the handwheel to check if the needle goes into the right and the left hole of the button without hitting the button. Slowly sew on the button with about 10 stitches. Select pattern " " and sew a few securing stitches (3). If a shank is required, place a darning needle on top of the button and sew (4). For buttons with 4 holes, sew through the front two holes first (3), push the work forward and then sew through the back two holes (4).

Sew 4-step buttonholes

Prepare 1. Take off the all purpose foot and attach the buttonhole foot. 2. Measure diameter and thickness of button and add 0.3 cm (1/8") for bar tacks; mark buttonhole size on fabric. 3. Place fabric under the foot, so that marking on the buttonhole foot aligns with starting marking on fabric. Lower the foot, so that the buttonhole center line marked on the fabric aligns with the center of the buttonhole foot. Adjust the stitch length dial in the " " to set stitch density.
Note: Density varies according to the fabric. Always test sew a buttonhole on the fabric you are using to sew the buttonhole. Follow the 4-step sequence changing from one step to another with the stitch pattern selector dial. Take care not to sew too many stitches in stages 2 and 4. Use seam ripper and cut buttonhole open from both ends towards the middle. Tips: - Slightly reducing upper thread tension will produce better results. - Use a backing for fine or stretchy fabrics. - It is advisable to use heavy thread or cord for stretch or knit fabrics. - The zig-zag should sew over the heavy thread or cord. (5)

Zippers and piping

Set the machine as illustrated. Dial selector on " ". Change to zipper foot. Set stitch length control between "1" - "4" (according to thickness of fabric). The zipper foot can be attached right or left, depending on which side of the foot you are going to sew. (1) To sew past the zipper tab, lower the needle into the fabric, raise the presser foot and push the zipper tab behind the presser foot. Lower the foot and continue to sew. It is also possible to sew a length of cord into a bias strip to form a "welt" or piping. (2)

Multi-stitch zig-zag

Sewing on lace and elastic, darning, mending, reinforcing edges. Set the stitch pattern dial to " ".
Place patch in position. The stitch length can be shortened to produce very close stitches. (1) When mending tears, it is advisable to use a piece of backing fabric to reinforce. The stitch density can be varied by adjusting the stitch length. First sew over the center and then overlap on both sides. Depending on the type of fabric and damage, sew between 3 and 5 rows. (2)

Bar tack

Set the stitch pattern dial to " " or " ".
Set the stitch length dial to "1" - "1.5". This function is used to secure the tops of kick pleats, as well as pocket openings. First use a straight stitch across the top of the pocket or pleat. This seam should be approximately 1/4 to 1/2 of an inch long. Set stitch to zigzag and stitch over the straight stitch backstitch at the beginning and end of stitch to secure ends. 1
Free motion darning, stippling
* The darning foot is an optional accessory not included with your machine. (1)
Set the machine as illustrated. Install the darning plate. (2) Remove the presser foot clamp. (3) Attach the darning foot to the presser foot holder. The lever (a) should be behind the needle clamp screw (b). Press the darning foot on firmly from behind with your index finger and tighten the screw (c). (4) For darning, first sew around the edge of the hole (to secure the threads). (5) First row: Always work from left to right. Turn work by 1/4 and oversew. A darning hoop is recommended for easier sewing and better results.
Note: Free motion darning is accomplished without the sewing machine internal feed system. Movement of the fabric is controlled by the operator. It is necessary to coordinate sewing speed and movement of fabric. Sew a straight or zigzag stitch following your design line. Using the optional darning foot will help guide you as you sew.

a b c 5

Practical stitches
Set the machine as illustrated. Turn the stitch length dial to suit the fabric and application.
Shell stitch (A) For decorative edges. Suitable for edges on sheer, fine and stretch fabrics. The larger stitch should go just over the edge of the fabric to create the shell effect. Crescent stitch (B) For a delicate edge finish along the edge of fabric.

Applique and blindstitch applique
Position applique piece on background fabric. Align needle so that it pierces background fabric along the outside edge if the applique. Lower presser foot. If using a blindhem foot, align the lip of the blindhem foot guide so that it sits directly under the edge of the applique. You may need to adjust the position of the guide to bring it closer or further from the edge of the applique, by using the thumbscrew located at the right of the foot. Begin sewing following the edge of your applique. To pivot for curves or corners, leave needle down in fabric on outside edge of applique, lift foot and pivot.

Quilting functions

Stippling is free motion quilting where you hoop the fabric and guide it by hand, allowing you to stitch in any direction. For template quilting transfer a design from a template (plastic stencil) to your fabric and then stitch following the outline. Do not forget to lower the presser bar if you are sewing without a foot. The above techniques are used to hold the layers of the quilt together. For better control use a hoop, as well as a Darning and Embroidery foot.

Mending

Machine Preparation: - Pattern: Multi - stitch Zigzag - Stitch width: Largest 4.5mm - Stitch length: Fine (0.5 - 1.0) Sewing Instructions: Position a piece of fabric directly beneath the tear in your fabric. Align the center of the foot with the center of the tear. Stitchacross, backstitching at the start and at the end of the seam.

Stay-stitching

Machine Preparation: - Pattern: Straight Stitch - Stitch Width: Straight - Stitch length: 1.5mm (fine) Sewing Instructions: Stay-stitching is used to reinforce curves such as armholes, seams in stretch fabrics and other areas to prevent stretching. Stay stitch along the edge of the area 1/4 of an inch from the edge of the seam.

Blindstitch applique

Machine Preparation: - Pattern: Blindhem - Stitch Length: 2 - 3 - Foot: Standard Zigzag or optional Blindhem foot Sewing Instructions: Position applique piece on background fabric and secure it in place using fabric glue. Align needle so that it pierces background fabric along the outside edge of the applique. Lower presser foot. Using Blindhem stitch, proceed to sew, following the edge of your applique. If using a Blindhem foot, align the lip of the blind hem foot guide so that it sits directly under the edge of the appliqu. You may need to adjust the position of the guide to bring it closer or further from the edge of the applique, by using the thumbscrew located at the right of the foot. To pivot for curves or corners, leave needle down in fabric on outside edge of applique, lift foot and pivot.

Traditional pintucks

Machine Preparation: - Pattern: Straight - Stitch Width: Straight - Stitch Length: 2 - 3 Sewing Instructions: To mark pintucks in your fabric, either pull a thread to mark the fold or mark with chalk or marking pencil. Fold and press wrong sides together on pulled thread line or marked lines. Stitch 1/8 of an inch from fold line. Repeat, sewing in the same direction for each tuck. Press flat.

Gathering

Machine Preparation: - Pattern: Straight Stitch - Stitch Width: Straight - Stitch Length: Longest Sewing Instructons: Use this technique for gathering waistbands, sleeve caps etc. At 1/4 of an inch from the edge of the seam, begin by backstitching and then continue to sew the length required. When seam is complete, raise the needle to it's highest, raise the presser foot and pull the upper and lower threads to the back of the foot. Cut your thread ends leaving a minimum 6 inches of thread. Repeat this procedure once again at 1/4 of an inch from your first row of stitching. Once the two rows are completed, draw in your fabric the required amount by pulling on the bobbin thread. Secure thread ends.

Couching

Machine Preparation: - Pattern: Zigzag - Stitch width: Variable (Set according to width of cord) - Stitch length: Variable - Foot: Zigzag or optional Satin foot Sewing Instructions: Couching is simply the technique of zigzagging over a fine cord. Use as a decorative touch on jackets and other sewing projects. With a marking pencil, draw a design on your fabric. Lay the cord under the center opening of your foot and zigzag over the cord so that the needle falls just to the right and left of the decorative cord. As you sew, follow the lines of your design.
Trim attachment stitch function
- Set the stitch pattern dial to zigzag. - Set the stitch length to "0". - Sew 6 to 8 stitches to secure the trim in place. - Then set needle to right needle position and then to sew the length of the trim. - Set stitch pattern dial to straight stitch. - Sew 2 to 3 stitches to tie off. - This function is used to attach trim or ribbon to a sewing project.

Maintenance

Attention: Disconnect the machine from the electrical supply by removing the plug from the main socket. When cleaning the machine, it must always be disconnected from the electrical supply.
Remove the needle plate: Turn the handwheel until the needle is fully raised. Open the hinged front cover and unscrew the needle plate screws with the screw driver (1). Cleaning the feed dogs: Use the brush supplied to clean the whole area (2). Cleaning and lubricating the hook: Remove the bobbin case. Snap the two hook retaining arms (3) outwards. Remove the hook race cover (4) and the hook (5) and clean with a soft cloth. Lubricate at the point (6) (1-2 drops) with sewing machine oil. Turn the handwheel until the hook race (7) is in the left position. Replace the hook (5). Replace the hook race cover and snap back the two hook retaining arms. Insert the bobbin case and bobbin and replace the needle plate. Important: Fabric lint and threads must be removed regularly. Your machine should be serviced at regular intervals at one of our service centers.

Trouble shooting guide

Problem Upper thread breaks Cause 1.The machine is not threaded correctly. 2.The thread tension is too tight. 3.The thread is too thick for the needle. 4.The needle is not inserted correctly. 5.The thread is wound around the spool holder pin. 6.The needle is damaged. 1.The bobbin case is not inserted correctly. 2.The bobbin case is threaded wrong. 3.The lower thread tension is too tight. 1.The needle is not inserted correctly. 2.The needle is damaged. 3.The wrong size or type of needle has been used. 4.The foot is not attached correctly. 1.The needle is damaged. 2.The needle is not correctly inserted. 3.Wrong needle size for the fabric. 4.The wrong foot is attached. 1.The machine is not correctly threaded. 2.The bobbin case is not correctly threaded. 3.Needle/ fabric/ thread combination is wrong. 4.Thread tension wrong. 1.The needle is too thick for the fabric. 2.The stitch length is incorrectly adjusted. 3.The thread tension is too tight. 1.Poor quality thread. 2.The bobbin case is incorrectly threaded. 3.Fabric has been pulled. 1.The machine must be lubricated. 2.Lint or oil have collected on the hook or needle bar. 3.Poor quality oil has been used. 4.The needle is damaged. Thread is caught in the hook. Correction 1.Rethread the machine. 2.Reduce the thread tension. (lower number) 3.Select a larger needle. 4.Remove and reinsert the needle. (flat side towards the back) 5.Remove the reel and wind thread onto reel. 6.Replace the needle. 1.Remove and reinsert the bobbin case and pull on the thread. The thread should pull easily. 2.Check both bobbin and bobbin case. 3.Loosen lower thread tension as described. 1.Remove and reinsert needle. (flat side towards the back) 2.Insert a new needle. 3.Choose a needle to suit the thread and fabric. 4.Check and attach correctly. 1.Insert a new needle 2.Insert the needle correctly. (flat side towards the back) 3.Choose a needle to suit the thread and fabric. 4.Select the correct foot. 1.Check the threading. 2.Thread the bobbin case as illustrated. 3.The needle size must suit the fabric and thread. 4.Correct the thread tension. 1.Select a finer needle. 2.Readjust the stitch length. 3.Loosen the thread tension. 1.Select a better quality thread. 2.Remove bobbin case, thread and insert correctly. 3.Do not pull on the fabric while sewing, let it be taken up by the machine. 1.Lubricate as described. 2.Clean the hook and feed dog as described. 3.Only use good quality sewing machine oil. 4.Replace the needle. Remove the upper thread and bobbin case, turn the handwheel backwards and forwards by hand and remove the thread. Lubricate as described.

Lower thread breaks

Skipped stitches

Needle breaks

Loose stitches
Seams gather or pucker Uneven stitches, uneven feed The machine is noisy

The machine jams

021V880105( ) Dec/05 SINGER 1507(8280C)

Parts List

SINGER Model 1507
No. Part No. Front cover Plate (1) Heat resistant plate Thread cutter WasherCS-5 Set screw (M4*8 A) Set screw (M4*10 B) Face plate complete Face plate Back cover Handle Spool pin Plate Thread guide Thread guide spring plate Hand wheel bushing pin (2*6*0.4) Set screw (M3*8.5B) Handle bracket Bobbin winder stopper Set screw (9/64*40*16 B) Nut (9/64*40 t=3) Set screw (M3*16.7 B) Free arm base complete Bed cover Hook cover Hook cover spring Set screw (M4*10 B) Sewing table complete Sewing table body Sewing table body cover Dial tension supporter plate complete Dial tension supporter plate cover Thread guide Set screw (M4) Washer (4.2*8*0.8) Set screw (M4*6 B) Description No. Part No. Description Thread guide spring Thread guide spring washer (C-4.5) Dial tension guide spring tube Hand wheel bushing pin (3*10) Dial tension supporter plate Dial tension waft plate E-ring (ETW-4) Set screw (M4*6) Dial tension disc (2) Dial tension disc (1) Dial tension spring regulator Dial tension spring Dial tension regulator Dial tension spring plate Dial tension knob Thread guide complete Washer (WW-5) Washer (5.2*10*0.5) Rod Zig zag width regulating cam box Zig zag cam contact supporter shaft Zig zag regulator crank E-Ring (ETW-5) Spring pin (3*8*0.6) Bobbin winder frame complete Bobbin winder frame Bobbin winder crank complate Bobbin winder crank spring Bobbin winder rubber pulley Feed regulator gear Feed regulator dial Bobbin winder thread guide complete Bobbin winder thread guide adjusting screw Bobbin winder spring disc Bobbin winder thread guide spring Washer (4.2*8*1) No. Part No. E-Ring (ETW-3) Description V886253210 V61503210 V880323000 VV887194210 V887193210 V886263210 V880083210 V610443210 V880353210 V880233001 V004230215 V61253006 E1AV880034000 V880033210 V880043210 RV880065210 V880063210 V880073210 V883064210 V886283210 VVHV60243002 V004240176 J30433001 J30423001 R10593000 NB1083000 K50193000 V60273006 V887783210 V004300643 V61043003 V70084000 V70103003 V003043008 V883074210 V61125006 V61165000* V61563003* F20213000* V61183000 V889283210 V886274210 V880173001 V880183001 V003010036 V886273210 VJ31413000 004240746

Page A

Bobbin winder thread guide base Plate Washer (4.2*20*1) Free arm base felt Set screw (M4*18 B)
"*"means: These spare parts are not supplied individually,but can be obtained by minimum quantity at 300 pcs.
No. Part No. Arm shaft Spring pin (3*18) Arm shaft clutch annulus spring Arm clutch collar Hand wheel Hand wheel washer (5.2*16*1) Hand wheel set screw (M5*10) Hand wheel decorated plate Arm shaft drive belt pulley Washer (10.2*15*0.5) E-ring (ETW-9) Arm shaft bushing Arm shaft bushing holder plate Set screw (M4*8 A) Arm shaft worm Set screw (M4*5 C) Crank connecting rod cam Set screw (11/64*40*12) Crank connecting rod Set screw (M4*6 B) Crank connecting rod cover Feed cam Set screw (M4*4 C) Arm shaft collar Set screw (M5*5 C) Endure attrition washer (10.2*16*0.5) Arm shaft balance Set screw (M4*6 C) Arm shaft balance pin (3.5*24) Needle bar crank rod Arm shaft balance pin Thread take up lever Thread take up lever supporter E-ring (ETW-4) Thread take up lever supporter shaft Thread take up lever supporter Plate Description No. Part No. Description Crank connecting rod complete Motor drive belt (B156XXL6.1) Arm shaft worm complete Feed cam complete Arm shaft collar complete Arm shaft balance complete Thread take up lever complete Washer (4.2*7.2*1.2) VR10393000 R10403000 V004250346 V16893210 E4A003010093 R10293000 VVVVV60073003 G 4A * 004240503* R004400080 V003043524 F4A3343000 V10543000 E1A2513001 VV60223003 H13093003 VV60093000 G4A0535000 R10304000 V61475000 E1A2534000 004600026

Page B

No. Part No. Arm Bed Presser bar regulating screw Presser bar Presser bar spring Presser bar bracket complete Presser bar bracket Set screw (M6*5 C) Tension regulating lifter spring Tension lever lifter Shank complete Shank complete screw (SM9/64 40*7) Zig zag presser foot complete (J) Needle bar Needle bar supporter Needle bar supporter pin E-ring (ETW-5) Set screw (9/64*40*5 A) Needle clamp complete Needle clamp Needle clamp set screw Needle Needle bar driving rod Needle bar driving rod pin Needle bar supporter spring Needle bar bracket complete Needle bar bracket (1) Needle bar bracket (2) Set screw (M4*0.7*4 C) Endure attrition washer (8.2*16*0.5) Shuttle driver shaft collar Set washer Shuttle driver shaft gear Set screw (11/64*40*4C) Needle plate Needle plate complete set screw (M4*6) Presser bar lifter lever Description No. 65 Part No. Description Presser bar lifter lever screw washer Set screw (M4*10 B) Set screw (M4*5 C) Tension lever regulating plate Shuttle driver shaft gear Open shuttle race complete Open shuttle race Shuttle holder Shuttle holder spring Shuttle holder spring screw Shuttle driver complete Shuttle driver Shuttle driver spring Shuttle driver spring screw Shuttle hook (4.6mm) Bobbin Bobbin case complete Bobbin case Bobbin case spring Bobbin case spring set screw Shuttle driver shaft collar complete Set screw (M4*8 A) Shank complete screw (SM9/*8) Endure attrition washer (7.6*12*0.13) Needle bar supporter pin complete Needle bar supporter complete Needle bar driving rod pin complete Shuttle holder complete E-ring (ETW-3) V880163000 V620163210 V70153002 V70163003* HH004260023 H10723003* VV70273000 V61973002 NG10245000 TA11033002 GV70023003 M H50583003* H10195000* H10253000* H10263000* 004240503* 004400210 HHVVV880153000 V004240033 V60143003 V620235000 V10995000 V11003002* V11573001* V11583002* H71093003* K81125000 K81123002* K81143003* 004103043* HH71185000 H71186001* H13803001* H13973002* HH50594000 V60134000 M30074000 V620234000 003010036

Page C

No. Part No. Description Pattern cam contact complete Pattern cam contact plate (front) Pattern cam contact plate (back) Zig zag cam contact supporter Zig zag cam contact Zig zag regulator plate E-Ring (ETW-6) Feed regulator crank BH regulator plate Zig zag cam contact spring BH spring Pattern selector cam plate Pattern plate Feed regulator Pattern cam shaft spring Set screw (M4*8 A) Set screw (M3*6 A) E-Ring (ETW-5) Set screw Regulate Set Nut (ALN-4) Set screw (M4*6 B) Set screw (M3*10 B) Set screw (M4*8) Washer (8.2*12*0.25) E-Ring (ETW-3) Set screw (M4*4 C) Pattern cam contact supporter shaft Pattern cam shaft Zig zag cam contact supporter shaft Pattern selector cam shaft Pattern cam Feed regulator cam Pattern selector cam BH pattern selector cam Zig zag regulator nut Rever plate No. 53 Part No. Set screw Spring Hand Wheel bushing pin(3*18*0.6) Pattern Selector dial Reverse lever Reverse rod Reverse lever set screw (M4) Reverse knob shaft mounting plate Washer(6.2*14*0.13) Reverse connecting plate Reverse knob shaft Selector dial spring Reverse knob Set screw (M4*6 C) Reverse knob complete Reverse knob shaft complete E-Ring (ETW-4) Description V883054000 V610053003 V60633005 V60703005 V60713003 VV810073003 V810153003 V10693003 V60813003 V60853003 V60873003 V60883003 VV60823003 V60643003 V60693000 V880303003 V90023000 V60683000 V810083000 V60863000 V60733000 VMV888283210 V880283006 VVV880263006 VVV883024210 V880254000 003010043

Page D

Page E

Part No. Description

Lampholder complete (only for 120V) Lampholdercomplete(only for 220V-240V) Lamp(120V 10W ) Lamp (240V 10W E-12) Lead wire assy Lead wire assy Motor complete (for 120V)HF-7150 Motor complete (for 230V) HF-07250 Belt wheel complete Lamp bracket Motor bracket Nut (M4 t=5) Nut (M3 t=2.3) Belt wheel Motor feed regulator collar E-Ring (ETW-3) Washer (5.4*10*0.9) Spring washer (5.2*9*1) Set screw (M5*12) Set screw (M3*8 B) Receptacle holder cover Set screw (M3*20) Concent insulation plate Receptacle Receptacle holder Set screw(M4*8) Switch assy End termind Cord clip Free arm foot buse Base plate adjustment screw Base plate adjustment screw spring Free arm base cushion rubber Clutch rod complete Clutch rod plate Clutch rod

E-Ring (E-4)

Description
Clutch rod spring Set screw (M4*6 B) Set screw (M3*5 B) Set screw (M3*8) Set screw(M4*8 A) Foot controller (KD1902)120V Foot controller (KD2902)230V Cushion rubber Free arm base cushion rubber Gobo Set screw (M4*10.2)
002396028 V002396029* 002425118 AAV610293210 K82133003 K82073003 H70043000 V61205003 V61213003 V61233003
003010046 V61243003* 008059302 E1A2503000 VG40123000 004240385
PageF No. Part No. Description Feed lifting rock crank complete Feed lifting rock crank Sew screw knob Sew screw Nut (M4 t=3) E-Ring (ETW-6) Feed lifting rock shaft Washer (4.2*7.2*1.2) Set screw (M4*15) Lower shaft gear Lower shaft gear set screw Lower shaft gear set screw Lower shaft collar Set screw (M4*4) Endure attrition washer Feed rock bushing Feed rock bushing holder plate Set screw (M4*8) Feed lifting rock cam Set screw (M4*5) Lower shaft Crank connecting rod crank Set screw (M5*5) Crank connecting rod crank pin E-Ring (ETW-5) Nut (9/64*40 t=3) Feed regulating spring Pattern cam shaft collar Set screw (M5*10A) Feet rock frame Set screw (1/8*44*5) Feet dog Feed dog frame Washer (4.2*8*0.8) Feed dog frame spring Bushing holder plate No. 67 Part No. Description Feed dog frame shaft E-Ring (ETW-3) Nut(SPN-4) Feed rock shaft Feed rock crank complete Set screw (M4*15 B) Washer (4*8*0.5) Feed rock crank Feed rock crank Nut (M4) E-Ring (ETW-4) Fork rod Fork rod spring Feed regulating block Feed regulating shaft Feed rdgulating Feed regulating plate Feed rod E-Ring (E-4) Set screw (9/64*40*11) Set screw (M4*10B) Endure attrition washer Feed rdgulating complete Fork rod complete Pattern cam shaft collar complete Feed rock shaft complete Lower shaft gear complete Lower shaft collar complete Crank connecting rod crank complete Lower shaft complete Crank connecting rod crank pin complete Endure attrition washer V60574000 V60583003 K81243000* 003010063 V004240146 V620073000* V004400410 V60343000 RVV620223000 VV004706013 V70063003* HVV620053000 VV60533003 V60563003 V003090043 V60483000 V004300093 V003010043 V60453003* V60463003* V11533000 V60443000 V60433000 V60393003 V60423003* V60384000 V60454000 H11935000 V60474000 V620075000 V11564000 V60354000 V620224000 V10835000 004400450

Page F

Standard accessories

Optional accessories

Page G
Standard accessories No. 13 Part No. Zipper foot(I) Buttonhole foot Quilting bar Embroider plate Accessories bag Screw drive (L) Orler Brush & Seam ripper complete Needle (14#.16#.11#) Bobbin Description Button sew-on foot No. Part No. Hemmer foot Cording foot Satin stitch foot Over casting foot Blind hem foot Embroidery 006066008 TA10943209 R12373210 Optional accessories Description

A B C D E F

016 008
Spool set plate (small) Spool set plate (big)
When you order any spare parts from us, please cooperate with us by writing. (1)Section & Sequence No. (2) Name of parts (3) Voltage, if necessary (4) Others, if any 029190038(A) JUN 0205
""means : These spare parts are not supplied individually , but cam be obtained by minimum quantity at 300 pcs.