2.5 mm 1.7 Nm 15 in.lbs.

WORLD HEADQUARTERS Chicago, Illinois U.S.A. SRAM Corporation 1333 North Kingsbury, 4th floor Chicago, Illinois 60622
ASIAN HEADQUARTERS Taichung, Taiwan SRAM Taiwan No. 1598-8 Chung Shan Road Shen Kang Hsiang, Taichung County 429 Taiwan R.O.C.
EUROPEAN HEADQUARTERS Amersfoort, The Netherlands SRAM Europe Basicweg 12-D 3821 BR Amersfoort The Netherlands

ANATOMY

USE CAUTION

stationary grip grip

COMPATIBILITY

3.0 Comp rear shifters:

INSTALLATION
Rear derailleurs SRAM X.0 / X.9 / X.7 / 5.0 / 4.0 / 3.0 (1:1 Actuation Ratio)

CABLE CHANGE ADVICE

Leave the shifter on the handlebar.
The shifter does not need to be opened no need to move other components. Use only new, high quality cable and compressionless cable housing. Detach the cable from the derailleur. Cut the cable off 6" (15 cm) from the shifter barrel adjuster. Discard the old cable and cable housing. Line up the 1 (front) or HIGHEST gear number (rear) mark with the indicator mark (MRX Comp Shimano Rapid Rise Gear number 1 for front and rear). Look for the cable entry.

Operating instructions

CAUTION
Read all instructions for correct installation and use.
Always check the front and rear brake levers for proper operation. If there is interference between a shifter and a brake lever, rotate one out of the way. Check for proper brake lever operation again!
Never ride without the stationary grips, this can result in severe injury or death. MRX Comp rear shifters:
Slide the shifter onto the handlebar. If necessary, move the brake lever to allow for the shifter and the stationary grip. Bar end users dont forget to leave room for the bar end.
Shifter 3.0 Comp MRX Comp
Released 2/2003 Publ. No. 4207 www.sram.com

barrel adjuster

Rear derailleurs Shimano (2:1 Actuation Ratio)
Rotate the shifter until the barrel adjuster is beneath (but out of the way of) the brake lever.
Tighten the 2.5 mm hex clamp bolt to 15 in.lbs. (1.7 Nm). Slide the stationary grip onto the handlebar. Never use lubricants or solvents to install stationary grips. They provide an axial safety function. For this reason, they should be mounted in such a way as to make sure they do not slip off handlebar. Never ride without the stationary grips, this can result in severe injury or death.

shifter

MAINTENANCE ADVICE
Clean the shifter using only water and mild soap.
This shifters are nearly maintenance free. For any questions regarding methods of disassembly or maintenance, please contact your qualified local dealer.
MRX Comp Rapid Rise rear shifters:
Rear derailleurs Shimano Rapid Rise (2:1 Actuation Ratio)
3.0 Comp / MRX Comp front shifters:
Front derailleurs SRAM & Shimano
Feed the cable through the cable housing and stops.
Not recommended for use on thin walled aluminium handlebars such as Hyperlite type handlebars.
Attach the front/rear shifter cable to the front/rear derailleur. Adjust indexing per the derailleur instructions.
Push cable up/out of the shifter and discard. Feed the new cable through the cable entry and out the barrel adjuster. Pull the cable snug. Feed the cable through the new cable housing and stops. Attach the cable to the derailleur and adjust indexing per the derailleur instructions.

EINZELTEILE

GEBRAUCH ACHTUNG
handlebar grip Festgriff Schaltgriff

KOMPATIBILITT

3.0 Comp rechter Schalter:

MONTAGE

Schaltwerke SRAM X.0 / X.9 / X.7 / 5.0 / 4.0 / 3.0 (1:1 bersetzung)

SCHALTZUGWECHSEL HINWEIS

Lassen Sie den Schalter auf dem Lenker. Sie mssen den Schalter zum Zugwechsel nicht ffnen. Es ist nicht erforderlich, andere Lenkeranbauteile zu verschieben. Verwenden Sie nur neue, qualitativ hochwertige Schaltzge und kompressionsfreie Aussenhllen.
Lsen Sie den Schaltzug am Umwerfer/Schaltwerk. Schneiden Sie den Schaltzug 15 cm vor der Schaltzugeinstellung ab. Entfernen und entsorgen Sie den alten Schaltzug und Seilhlle. Drehen Sie den linken Schaltgriff auf Gang 1. Den rechten Schaltgriff drehen Sieauf den hchsten Gangzahl (MRX Comp Shimano Rapid Rise Schalter: Gang 1 ). Der Schaltzugeinlass ist nun sichtbar.

Betriebsanleitung

ACHTUNG
Lesen Sie bitte zuerst diese Informationen sorgfltig durch und befolgen Sie die darin beschriebenen Anweisungen genau.

Schaltzugeinstellung