COOLPIX990, 950

Betriebsart Autofokus-Betriebsart Blitzeinstellung M-REC Makro Blitz aus Zeitautomatik (A), Blende 4 bis 5 Zeitautomatik (A), mittlere Blende Auto 100 automatischer Weiabgleich oder Messwert

1, 2, or 3 Auto

Mode Dial Focus Mode Flash Setting Exposure Mode Focus E990 E950
M-REC Macro close-up Flash Cancel (off) Aperture Priority Auto (A), aperture f 45 Aperture Priority Auto (A), middle aperture setting Auto
Lens Menu Option Slide Copy Adptr
Sensitivity 100 (ISO equivalency) White Balance Auto white balance or white balance set using preset white balance option

COOLPIX4500

Exposure Mode
Holder for strip film Filmstreifenhalter Support pour ngatifs en bande Portapelcula Filmstrookhouder Montatura per porta-originali in striscia Holder for slide mounts Diahalter (fr gerahmte Dias) Support pour diapositives montes Portadiapositivas Diaframehouder Montatura porta-originali intelaiati

P, S, A, M Auto

Belichtungs-steuerung P, S, A, M Option aus Men Objektiv Fokus Empfindlichkeit (entsprechend ISO) Weiabgleich Dia-Adapter Auto 100
Lens Menu Option Slide Copy Adptr Focus

COOLPIX4300, 885, 880

E4300 M Betriebsart E885 CSM E880 P, A, M, CSM Option aus Men Objektiv Dia-Adapter Auto 100 automatischer Weiabgleich oder Messwert

COOLPIX4300*, 885*, 880

E4300 M Mode Dial E885 CSM E880 P, A, M, CSM Lens Menu Option Slide Copy Adptr
/Figure 2/Abbildung 2/Figure 2/Figura 2/Figuur 2/Figura 2

COOLPIX995

Mode Dial Focus
automatischer Weiabgleich oder Messwert
Betriebsart Option aus Men Objektiv Fokus Empfindlichkeit (entsprechend ISO) Weiabgleich

Dia-Adapter Auto

Fokus Empfindlichkeit (entsprechend ISO) Weiabgleich
Sensitivity 100 (ISO equivalency) White Balance
Auto white balance or white balance set using preset white balance option
100 automatischer Weiabgleich oder Messwert
COOLPIX5000/4300/885: Digital zoom is automatically used.
3 With the image in the LCD monitor as your guide, use the zoom buttons to adjust the picture angle.
The camera will focus automatically. In macro close-up mode, the COOLPIX990 and 950 will not be able to focus when zoomed to a position close to minimum or maximum zoom. Adjust zoom appropriately.
3 Mit den Zoomtasten der Kamera knnen Sie den Bildwinkel auf einen Ausschnitt der Filmvorlage

Nikon 950 mode switch repair- continued

Back to Step 1

Step 2:
In this step you are going to remove the front cover that holds the mode switch. There are 6 screws to remove in all. First you should remove the batteries. Next apply a 2 inch strip of electrical tape to the top of the lens/flash section of the camera body (see Frame 1). This will protect the camera body from the screwdriver while youre removing and replacing the inside front cover screws. I didnt do this and ended up creating a few dings in my camera body, ouch! I used a Kodak DC210 to take the pics and was not familiar with it and a few are out of focus, sorry.

Frame 1

Now remove the inside front cover screws (see Frame2 & Frame3) and place them in your container. Youll probably have to apply a little pressure to get these out, they are the tightest ones, just make sure you dont strip the heads on the screws. If youre having a hard time getting them loose, put a drop of WD40 on them and let sit for a few minutes. In Frame 3 youll notice that you need to swing the lens over to self-portrait position to get to the bottom screw. Notice that these are fine threaded metal-to-metal screws and need to go back into these 2 places. The other 4 screws use wider spaced threads and go into plastic on the frame of the camera.

Frame 2

Frame 3 Next remove the 2 screws on the side of the camera (see Frame 4). Then remove the 2 screws on the bottom of the camera (see Frame 5 & Frame 6).Youll have to open the battery compartment to get to the one screw shown in Frame 5. Also notice in Frame 6 that you DO NOT remove the one screw in the middle, that one holds the tripod mount to the front cover.

Frame 4

Frame 5
Frame6 Now flip open the rubber cover protecting the jacks on top of the camera. Then with the camera in the upside-down position and the front cover facing you as shown in Frame 7, very gently pull the front cover off. I did this by wedging my fingernails between the front and back covers on the side of the camera, prying them apart. You could also try using a small flat-bladed screw driver to do this. This should get it started anyway. The reason you need to be gentle here is because of the ribbon cable (see Frame 8) that connects the mode switch to the circuit board on the camera, it is easy to break these so take your time. Once you have the front cover pulled away from the camera, you can then lay the camera on its back and lay the cover down towards you exposing the inside of the camera (see Frame 8). The ribbon cable is just long enough to allow for this for repair.

Frame 7

Frame 8

Onto Step

My astrophotography website: "Events in the Night Sky" Photos on my website shot with my Nikon Coolpix 950 are "Sun Pillar" and "Circumzenithal Arc" Nikon ES-E28 slide copy adaptor used with my Nikon Coolpix 950 on "Hunter's Moon and Jupiter Rising" All material copyright 2001 Stan Richard