Never fire the flash while it is too close to the subjects eyes. Intense light from the flash can cause eye damage if it is fired too close to the eyes. This is especially true with young children. When using the flash, the camera should be at least one meter (3.3) from the eyes of the subject. Keep the camera away from water and other liquids, and never let it get wet. Moisture creates the risk of fire and electric shock. Never use the camera outdoors in the rain or snow, at the seashore or beach, in the bathroom, etc. Should foreign matter or water ever get into the camera, immediately turn it off. Next, remove the cameras battery and/or unplug the AC adaptor power cord from the power outlet, and contact your dealer or nearest CASIO authorized service center. Using the camera under these conditions creates the risk of fire and electric shock. Should you ever notice smoke or a strange odor coming out of the camera, immediately turn it off. Next, taking care you do not burn your fingers, remove the cameras battery and/or unplug the AC adaptor power cord from the power outlet, and contact your dealer or nearest CASIO authorized service center. Using the camera under these conditions creates the risk of fire and electric shock. After making sure there is no more smoke coming from the camera, take it to your nearest CASIO authorized service center for repair. Never attempt your own maintenance.
INTRODUCTION Never use the AC adaptor to power any other device besides this camera. Never use any other AC adaptor besides the one that comes with this camera. Never cover the AC adaptor with a quilt, blanket, or other cover while it is in use, and do not use it near a heater. At least once a year, unplug the AC adaptor power cord from the power outlet and clean the area around the prongs of the plug. Dust build up around the prongs can create the risk of fire. If the cameras case should ever become cracked due to dropping it or otherwise subjecting it to rough treatment, immediately turn it off. Next, remove the cameras battery and/or unplug the AC adaptor power cord from the power outlet, and contact your dealer or nearest CASIO authorized service center. Never use the camera inside of an aircraft or in any other area where its use is prohibited. Doing so creates the risk of accident. Physical damage and malfunction of this camera can cause the data stored in its memory to be deleted. Always keep backup copies of data by transferring them to personal computer memory. Never open the battery cover, disconnect the AC adaptor from the camera, or unplug the AC adaptor from the wall socket while an image is being recorded. Doing so will not only make storage of the current image impossible, it can also corrupt other image data already stored in file memory.

I Test for proper operation before using the camera!
Before using the camera to record important images, make sure you first record a number of test images and check the results to ensure that the camera is configured correctly and operating properly.

I Data Error Precautions

Your digital camera is manufactured using precision digital components. Any of the following creates the risk of corruption of data in file memory. Removing the battery or memory card, or setting the camera onto the USB cradle while the camera is performing a record or memory access operation Removing the battery, removing the memory card, or placing the camera onto the USB cradle while the green operation lamp is still flashing after you turn off the camera Disconnecting the USB cable, removing the camera from the USB cradle, or disconnecting the AC adaptor from the USB cradle while a data communication operation is being performed Low battery power Other abnormal operations Any of the above conditions can cause an error message to appear on the monitor screen (page 271). Follow the instructions provided by the message to eliminate the cause of the error.

I Operating conditions

This camera is designed for use in temperatures ranging from 0C to 40C (32F to 104F). Do not use or keep the camera in the following areas. In areas subject to direct sunlight In areas subject to high humidity or dust Near air conditioners, heaters, or other areas subject to temperature extremes Inside of a closed vehicle, especially one parked in the sun In areas subject to strong vibration

I Condensation

When you bring the camera indoors on a cold day or otherwise expose it to a sudden change of temperature, there is the possibility that condensation can form on the exterior or on interior components. Condensation can cause malfunction of the camera, so you should avoid exposing it to conditions that might cause condensation. To keep condensation from forming, place the camera into a plastic bag before moving it into a location that is much warmer or colder than your current location. Leave it in the plastic bag until the air inside the bag has a chance to reach the same temperature as the new location. If condensation does form, remove the battery from the camera and leave the battery cover open for a few hours.

I Power Supply

Use only the special NP-40 rechargeable lithium ion battery to power this camera. Use of any other type of battery is not supported. This camera does not have a separate battery for the clock. The date and time will reset whenever the camera is not supplied power by the battery and/or the USB cradle for about 24 hours. Be sure to reconfigure these settings after power is interrupted (page 194).

I Caring for your camera

Fingerprints, dust, or any other soiling of the lens can interfere with proper image recording. Never touch the lens with your fingers. You can remove dust particles from the lens surface by using a lens blower to blow them off. Next, wipe the surface of the lens with a soft lens cloth. Fingerprints, dirt, and other foreign matter on the flash can interfere with proper operation of the camera. Avoid touching the flash. If the flash becomes dirty, wipe it clean with a soft, dry cloth. If the exterior of the camera needs cleaning, wipe it with a soft, dry cloth.

1. Turn on the camera. 2. Press [MENU]. 3. Use [] and [] to select the Set Up tab. 4. Use [] and [] to select the feature whose
setting you want to configure, and then press [].
GETTING READY The Auto Power Off and Sleep features are disabled in the following cases. When the camera is connected to a computer or some other device through the USB cradle While a slideshow is in progress While playing back a voice recording file While a movie is being recorded While playing back a movie NOTE You also can conserve battery power by selecting 0 for the monitor screen brightness setting (page 199).
Using the On-screen Menus
Pressing [MENU] displays menus on the monitor screen that you can use to perform various operations. The menu that appears depends on whether you are in a REC mode or the PLAY mode. The following shows an example menu procedure in a REC mode.

1. Press the power

button or [ ] (REC).
If you want to enter the PLAY mode instead, press [ ] (PLAY).

2. Press [MENU].

[MENU]
Selection cursor (indicates the currently selected item)

G Menu Screen Operations

When you want to do this: Move between tabs Move from the tab to the settings Do this: Press [] and []. Press []. Press []. Press [] and []. Press [] or press [SET]. Press [] and []. Press [SET]. Press []. Press [MENU].

[] [] [] []

Move from the settings to the tab Move between the settings Display the options available for a setting

[SET ]

Settings
Select an option Apply the setting and exit the menu screen Apply the setting and return to tab selection Exit the menu screen
3. Press [] or [] to select the tab you want,
and then press [SET] to move the selection cursor from the tab to the settings.
6. Perform one of the following operations to
apply the setting you configured.
To do this: Perform this key operation: Press [SET]. Press []. 1. Press []. 2. Use [] to move back up to tab selection. Apply the setting and exit the menu screen. Apply the setting and return to feature selection in step 4. Apply the setting and return to tab selection in step 3.

4. Use [] and [] to

select the feature whose setting you want to configure, and then press [].
Instead of pressing [], you could also press [SET].
Example: To select the Self-timer item.
See Menu Reference on page 259 for more information about menus.

selected setting.

Configuring Display Language and Clock Settings
Be sure to configure the following settings before using the camera to record images. Display language Home city Date Style Date and time

Using the Optical Viewfinder
You can conserve battery power by turning off the cameras monitor screen (page 33) and using the optical viewfinder to compose images. The optical viewfinder also comes in handy when shooting in areas where the monitor screen is difficult to view because available lighting is dim, etc. IMPORTANT! The visible area framed by the viewfinder shows the image that would be recorded at a distance of about one meter (3.3). When recording a subject that is closer to you than one meter, the recorded image will be lower than what you can see inside the viewfinder area.

Optical viewfinder

Area recorded at distances less than one meter (3.3)
Area visible in the viewfinder
BASIC IMAGE RECORDING Since the monitor screen shows exactly what will be recorded, always use it for composing images in the Macro and Manual Focus modes.

Using Zoom

Your camera is equipped with two types of zoom: optical zoom and digital zoom. Normally, the camera automatically switches over to digital zoom after you reach the maximum limit for optical zoom. You can, however, configure the camera to disable digital zoom, if you want.

Optical Zoom

The optical zoom range is 1X to 3X.
1. In a REC mode, move the
zoom controller left or right to zoom.
Moving the zoom controller as far as it goes in either direction will zoom at high speed.

Zoom controller

To do this: Zoom out for a wider view (main subject becomes smaller) Zoom in for a closer view (main subject becomes larger)
Move the zoom controller in this direction: (Wide Angle) (Telephoto)
BASIC IMAGE RECORDING NOTE The optical zoom factor also affects the lens aperture. Use of a tripod is recommended to protect against hand movement when using the telephoto setting (zoom in). Whenever you perform an optical zoom operation while recording with the Auto Focus mode, Macro mode or manual focus, a value will appear on the monitor screen to tell you the focusing range (pages 80, 83, 85). Optical zoom is disabled during movie recording. Digital zoom only is available. Make sure you select the optical zoom setting you want to use before you press the shutter button to start movie recording (page 120).

Zoom out

Zoom in
2. Compose the image, and then press the

shutter button.

Digital Zoom
Digital zoom digitally enlarges the part of the image at the center of the image screen. The range of digital zoom is 3X to 24X (in combination with optical zoom). IMPORTANT! When you perform a digital zoom operation, the camera manipulates the image data to enlarge the center of the image. Unlike optical zoom, an image enlarged with digital zoom appears coarser than the original. Digital zoom is not supported while date stamping (Date or Date&Time) is turned on (page 147).
I To record an image using digital zoom

1. In a REC mode, hold

the zoom controller towards (telephoto) side.
This causes the zoom indicator to appear on the display.

Digital zoom indicator

Zoom indicator
2. When the zoom pointer reaches the optical/
digital zoom switch over point, it will stop.
Optical Zoom range 1X 3X Zoom pointer Optical/digital zoom switch over point Digital Zoom range 24X
The above shows what the zoom indicator looks like when digital zoom is turned on (page 66). The digital zoom range is not displayed when digital zoom is turned off.
3. Release the zoom controller momentarily, and
(telephoto) side again then slide it towards to move the zoom pointer into the digital zoom range.
The zoom pointer will also stop when you move the pointer back to the switch over point to re-enter the optical zoom range. Release the zoom controller and (wide angle) side again to then slide it towards move into the optical zoom range.
I To turn digital zoom on and off
1. In a REC mode, press [MENU]. 2. Use [] and [] to select the REC tab. 3. Use [] and [] to select Digital Zoom, and

then press [].

To do this: Turn on digital zoom Turn off digital zoom Select this setting: On Off
4. Compose the image, and then press the
Only the optical zoom range is displayed in the zoom indicator when digital zoom is turned off.

Using the Flash

Perform the following steps to select the flash mode you want to use. The approximate effective range of the flash is shown below. Wide Angle Optical Zoom: Approximately 0.1 to 4.3 meters (0.33 to 14.1) (ISO Sensitivity: Auto) Telephoto Optical Zoom: Approximately 0.5 to 2.4 meters (1.6 to 7.9) (ISO Sensitivity: Auto) * Depends on zoom factor.

Flash Unit Status

You can find out the current flash unit status by pressing the shutter button half way and checking the monitor screen and red operation lamp.

Red operation lamp*

The indicator is also shown on the monitor screen when the flash unit is ready to fire.

* Red operation lamp

When the red operation lamp is this: Flashing Lit It means this: Flash unit is charging Flash unit is ready to fire
Changing the Flash Intensity Setting
Perform the following steps to change the flash intensity setting.

Using Flash Assist

Recording a subject that is outside the flash range can cause the subject to appear dark in the resulting image, because not enough of the flash reaches the subject. When this happens, you can use flash assist to correct the brightness of the recorded subject, so it appears as if the flash illumination was sufficient.
1. In a REC mode, press [MENU]. 2. Use [] and [] to select the Quality tab. 3. Use [] and [] to select Flash Intensity,
To make flash intensity: Stronger Normal Weaker Select this setting: +2 +1 2

Flash assist used

Flash assist not used
1. In a REC mode, press [MENU]. 2. Use [] and [] to select the Quality tab. 3. Use [] and [] to select Flash Assist, and
IMPORTANT! Flash intensity may not change if the subject is too far or too close to the camera.
To do this: Turn on flash assist Turn off flash assist Select this setting: Auto Off

I Flash Precautions

Take care that your fingers do not block the flash when you hold the camera. Covering the flash with your finger can greatly reduce its effectiveness.
IMPORTANT! Flash assist may not produce the desired result for some types of subjects. Flash assist may have little effect on your image if you changed any of the following settings when you recorded it. Flash intensity (page 71) Exposure compensation (EV shift) (page 88) ISO sensitivity (page 142) Contrast (page 146) Using flash assist can cause an increase of digital noise in recorded images. You may not be able to achieve the desired results using the flash if the subject is too close or too far away. The flash takes anywhere from a few seconds to as long as 10 seconds to attain full charge after being fired. The actual time required depends on the battery level, temperature, and other conditions. The flash does not fire in the modes listed below. The (Flash Off) icon on the monitor screen indicates that flash is turned off. Movie mode, MOVIE BEST SHOT mode The flash unit may not be able to charge when camera battery power is low. If this happens, the flash will not fire properly and you will not be able to obtain the desired exposure. Be sure to charge the cameras battery as soon as possible when power goes low.

selection boundary to the area of the monitor screen you want, and then press [SET].
4. Press the shutter button once to record.
This records two images: the image on the monitor screen and the image within the selection boundary, digitally zoomed to twice its normal size.
25-shot Stop Action Images (Using the Multi Continuous Shutter Mode)
Use the following procedure to record 25 consecutive stopaction shots at high speed and combine them into a single image.
IMPORTANT! Note with the above procedure, you do not need to keep the shutter button depressed. The size of the 25-shot images is pixels.
Multi Continuous, and then press [SET].
3. Press the shutter button once to record.
After 25 shots are recorded, they are combined into a single image, which is stored in memory.
Continuous Shutter Precautions
Starting a continuous shutter operation causes the exposure and focus settings to be fixed at the levels for the first image. The same settings are applied to all subsequent images. Continuous shutter cannot be used in combination with any of the following features. BEST SHOT (Business Cards and Documents, Whiteboard, etc., Old Photo, ID Photo, Pastel, Illustration, Cross), Movie mode, MOVIE BEST SHOT mode When using a continuous shutter mode, keep the camera still until all recording is finished. A continuous shutter operation may stop part way through if memory capacity runs low. Using a slow shutter speed setting causes a longer interval between images. The continuous shutter rate depends on the current image size and image quality settings. You can select the flash mode you want with normalspeed continuous shutter mode. With the normal-speed continuous shutter mode and multi continuous shutter mode, the flash mode automatically becomes (flash off). With the flash continuous shutter mode, the flash mode automatically becomes (flash on).
You cannot use the self-timer in combination with the normal-speed continuous shutter mode (page 73). Triple Self-timer (page 74) can be used in combination with the zoom continuous shutter mode only. The slowest possible shutter speed setting when using the multi continuous shutter mode is 1/15 second. Note that the resolution of images recorded with the highspeed continuous shutter mode or flash continuous shutter mode is somewhat lower resolution and more prone to digital noise than images recorded with the normal-speed continuous shutter mode. Auto ISO sensitivity always is used for the high-speed continuous shutter mode or flash continuous shutter mode, regardless of the current ISO sensitivity setting. With the flash continuous shutter mode, the flash range is narrower than normal.

Using the BEST SHOT Mode

Simply select one of a collection of built-in sample scenes and the camera sets up for the scene you selected for beautiful snapshots every time.

want to delete.

4. Press [] (
) to delete the user setup.
1. Perform one of the procedures below to

enable Anti Shake.

Using the BEST SHOT mode 1. In a REC mode, align the mode dial with then press [SET]. , and
5. Use [] and [] to select Delete. 6. Press [SET] to delete the file. 7. Select another scene, and then press [SET].
This returns to the recording state.
2. Use [], [], [], and [] to select the Anti Shake scene, and then press [SET].
OTHER RECORDING FUNCTIONS Using the Menu Screen 1. In a REC mode, press [MENU]. 2. Select the REC tab, select Anti Shake, and then press []. 3. Use [] and [] to select Auto, and then press [SET]. (Anti Shake indicator) is displayed on the monitor screen while Anti Shake is turned on. IMPORTANT! Anti Shake is disabled automatically when any setting other than Auto is selected for ISO sensitivity. If you want Anti Shake to be operational after turning it on, be sure to change the ISO sensitivity setting to Auto (page 142). Recording with Anti Shake can cause an image to appear somewhat coarser than normal and can cause slight deterioration of image resolution. The Anti Shake feature may not be able to eliminate the effects of hand or subject movement when shaking is severe. The Anti Shake feature may not work when using a very low shutter speed. If this happens, use a tripod to stabilize the camera. Though (Anti Shake) is displayed on the monitor screen while the flash setting is Auto Flash, Flash On, or Soft Flash, Anti Shake is disabled. While recording with Anti Shake, the maximum digital zoom factor is 4X (page 65).
Shooting with High Sensitivity
Higher sensitivity makes it possible to record brighter images, without using flash, even when there is not enough lighting available to obtain normal exposure.
IMPORTANT! High Sensitivity is disabled automatically when any setting other than Auto is selected for ISO sensitivity. If you want High Sensitivity to be operational after turning it on, be sure to change the ISO sensitivity setting to Auto (page 142). Recording with high sensitivity can cause an image to appear somewhat coarser than normal and can cause slight deterioration of image resolution. A desirable level of image brightness may not be possible under very dark conditions. When shooting with slow shutter speeds, use a tripod to protect against the effects of hand movement. High Sensitivity is disabled while the flash setting is Auto Flash, Flash On, or Soft Flash. While recording with High Sensitivity, the maximum digital zoom factor is 4X (page 65).

2. Use [], [], [], and [] to select the High
Sensitivity scene, and then press [SET].
Recording Images of Business Cards and Documents (Business Shot)
Recording a business card, document, whiteboard, or similarly shaped object from an angle can cause the subject to appear misshaped in the resulting image. Business Shot automatically corrects the shape of rectangular objects to make them appear like the camera was positioned directly in front of them.

I Setup Sample Images

Business cards and documents White board, etc.
Before keystone correction
After keystone correction
Before recording with Business Shot
Before recording, compose the image so outline of the item you want to record fits entirely within the monitor screen. Make sure the object is against a background that allows its outline to stand out, and that it fills the monitor screen to the maximum extent possible. NOTE When the camera is at an angle to a business card or document it is recording, the shape of the business card or document may appear distorted in the image. Auto keystone correction corrects for this distortion, which means that subjects appear normal even if you record at an angle.

To use Business Shot

2. Use [], [], [] and [] to select the
Business Shot image you want, and then press [SET].

3. Press the shutter

This displays a screen that shows all of the objects in the image that qualify as candidates for keystone correction. An error message will appear (page 271) if the camera is unable to find any suitable keystone correction candidate in the image. After a short while, the original image will be stored in memory, as-is.
4. Use [] and [] to select the candidate you

want to correct.

Restoring an Old Photograph
You can use the procedure in this section to restore an old, faded photograph with the color provided by modern digital camera technology.

5. Use [] and [] to

1. In a REC mode, press [MENU]. 2. Select the Quality tab, select Saturation,
1. In a REC mode, press [MENU]. 2. Select the Quality tab, select Contrast,
To get this: High color saturation (intensity) Normal color saturation (intensity) Low color saturation (intensity) Select this setting: +2 +1 2
To get this: High contrast Normal contrast Low contrast Select this setting: +2 +1 2

Date Stamping Snapshots

You can have the snapshots recording date only, or date and time stamped in the lower right corner of the image.
IMPORTANT! Once date information is stamped in a print, it cannot be deleted. Use the Date Style setting (page 195) to specify the format of the date. The recording date and time are determined in accordance with the cameras clock settings (pages 51, 194) when the snapshot is recorded. Digital zoom is not supported while date stamping (Date or Date&Time) is turned on (page 65). Date stamping is not supported for the following types of images. Images recorded with certain BEST SHOT scenes (Business Cards and Documents, Whiteboard, etc., Old Photo, ID Photo, Pastel, Illustration, Cross) Images recorded with the zoom continuous shutter mode and multi continuous shutter mode (pages 100, 101)
1. In a REC mode, press [MENU]. 2. Select the Set Up tab, select Timestamp,
Example: December 24, 2006, 1:25 p.m.
To include this date stamp information: Recording date (2006/12/24) Recording date and time (2006/12/24 1:25pm) Nothing Select this setting: Date Date&Time Off

Resetting the Camera

Use the following procedure to reset all of the cameras settings to their initial defaults as shown under Menu Reference on page 259.
IMPORTANT! The following are not initialized when you reset the camera (page 259). Home Time setup World Time setup Adjust Date Style Language Video Out
1. Press [MENU]. 2. Select the Set Up tab, select Reset, and
3. Use [] and [] to select Reset, and then
To cancel the procedure without resetting, select Cancel and press [SET].
Using the Shortcut Menu (EX Menu)
Pressing [EX] displays a shortcut menu that you can use to configure image size, white balance, ISO sensitivity, and AF area settings.
2. Use [] and [] to select the item you want,
and then use [] and [] to scroll through the available settings.
Refer to the following pages for details about each of the settings. Specifying Image Size (page 76) Adjusting the White Balance (page 89) Specifying ISO Sensitivity (page 142) Specifying the Auto Focus Area (page 82)

I To cut everything before or after a specific frame

1. While the movie you

are editing is playing, press [SET].
This will pause movie playback.

2. Press [].

You can also display the same screen while in the PLAY mode, by pressing [MENU], selecting the PLAY tab, selecting Movie Editing, and then pressing [].
3. Use [] and [] to select the operation you

want to perform.

To do this: Cut everything before a specific frame Cut everything after a specific frame Exit the cut mode Cancel Select this setting: Cut Cut
4. Display the frame where you want the cut to

be located.

To do this: Fast forward or fast reverse playback Pause or unpause movie playback Scroll paused playback one frame Cancel the cut operation Do this: Press [] or []. Press [SET]. Press [] or []. Press [MENU].

5. When the frame you

want is displayed, press [].
6. Use [] and [] to select Yes, and then
The message Busy. Please wait. will remain on the display as the cut operation is performed. Cutting is complete when the message disappears. Select No to exit the cut mode.
The red portion of the indicator bar shows what part will be cut.
I To cut everything between two specific frames
4. Display the starting frame where you want the

first cut to be located.

1. While the movie is

playing, press [SET].

3. Use [] and [] to select
Select Cancel to exit the cut mode.

Cut, and

6. Referring to step 4,
search for the cut end screen. When the cut end screen is displayed, press [].
Capturing a Still Image from a Movie (MOTION PRINT)
The MOTION PRINT feature lets you capture a frame from an existing movie and create a still image that is suitable for printing. There are two layouts you can use when capturing an image, and the layout you select determines the final image size. 9 frames (1600 1200-pixel final image size)
7. Use [] and [] to select Yes, and then
Background images Selected main image
1 frame (640 480-pixel final data size)

Selected main image

I To capture a still image from a movie
5. Use [] and [] to display the frame that you
want to use as the main image.
Holding down either button scrolls at high speed.
through movies on the monitor screen and display the one that contains the frames you want.

6. After selecting the

frame you want, press [SET].
This displays the resulting still image. If you selected 9 frames for the layout, the frame you selected in step 4 will be the main image, and the frames on either side of it will be used as the background frames. If you selected 1 frame in step 4, an image of the frame you selected in step 6 appears here. IMPORTANT! MOTION PRINT is not possible for movies not recorded with this camera.

* Seiko Epson Corporation holds the copyright for PRINT Image Matching and PRINT Image Matching III.

Exif Print

Exif Print is an internationally supported, open standard file format that makes it possible to capture and display vibrant digital images with accurate colors. With Exif 2.2, files include a wide range of shooting condition information that can be interpreted by an Exif Print printer to produce betterlooking prints. IMPORTANT! Information about the availability of Exif Print compatible printer models can be obtained from each printer manufacturer.
Using the Camera with a Windows Computer
The following are the general steps for viewing and copying files from a computer running under Windows. You can find details about each operation in the procedures that follow below. Note that you should also refer to the documentation that comes with your computer for other information about USB connections, etc. 1. If you are running Windows 98SE or 98, install the USB driver onto your computer. You need to perform this step only once, the first time you connect to your computer. If you are running Windows XP, 2000, or Me, you do not need to install the USB driver. 2. Use the USB cradle to establish a connection between the camera and computer. 3. View and copy the images you want.
After using the USB cradle to establish a USB connection between the camera and your computer, you can use your computer to view images in file memory and copy images to your computers hard disk or other storage media. In order to do this, you first need to install the USB driver located on the CD-ROM that comes bundled with the camera onto your computer. Note that the procedure you need to perform depends on whether you are using computer running under Windows (see below) or a Macintosh (see page 228).
VIEWING IMAGES ON A COMPUTER IMPORTANT! Low battery power can cause the camera to power down suddenly during data communication. Use of the special AC adaptor is recommended to power the camera during data communication. If you are using battery power without the AC adaptor, make sure that the battery is fully charged. If you want to transfer files from the cameras built-in memory to a computer, make sure there is no memory card loaded in the camera before you place it onto the USB cradle. This camera supports USB 2.0 Hi-Speed protocol. Though it can be used with a computer that supports only USB 1.1 protocol, higher speed data transfer becomes possible when USB 2.0 Hi-Speed is supported. Note that certain computer models, connecting through a USB hub, and other system conditions can slow down data transfer and even cause operational problems. Do not try to establish a connection between the camera and computer before installing the USB driver onto the computer. If you do, the computer will not be able to recognize the camera. USB driver installation is required in the case of Windows 98SE and 98. Do not connect the camera to a computer running one of the above operating systems without installing the USB driver first. USB driver installation is not required in the case of Windows XP, 2000, and Me.

This will cause your computer to create a hardware profile for cameras built-in memory or the memory card loaded in the camera. You do not need to install the USB driver every time. After you install it once, your computer will recognize the cameras built-in memory or its memory card when you establish a USB connection between the camera and your computer.

[USB] lamp

[USB] button
14. On your computer, double-click My

Computer.

If you are running Windows XP, click [Start] and then [My Computer].
19. Depending on your operating system, perform
one of the following procedures to save the files, if you want.
Windows 2000, Me, 98SE, 98 1. In the cameras file memory (Removable Disk), rightclick the DCIM folder. 2. On the shortcut menu that appears, click [Copy]. 3. Double click [My Documents] to open it. 4. On the My Documents [Edit] menu, click [Paste]. This copies the DCIM folder (which contains the image files) to your My Documents folder. Windows XP 1. In the cameras file memory (Removable Disk), rightclick the DCIM folder. 2. On the shortcut menu that appears, click [Copy]. 3. Click [Start] and then [My Documents]. 4. On the My Documents [Edit] menu, click [Paste]. This copies the DCIM folder (which contains the image files) to your My Documents folder.
15. Double-click Removable Disk.
Your computer sees the cameras file memory as a removable disk.
16. Double-click the DCIM folder. 17. Double-click the folder that contains the

image you want.

18. Double-click the file that contains the image

you want to view.

For information about file names, see Memory Folder Structure on page 235. NOTE If you open a rotated image on your computer, the original unrotated version will appear (page 175). This is true both for a rotated image opened from camera memory and for a rotated image that has been copied to your computers hard disk.
VIEWING IMAGES ON A COMPUTER NOTE If you already have a folder named DCIM in your computers My Documents folder, performing the procedures under step 19 above will overwrite the existing DCIM folder with the newly saved folder. If you want to save the contents of the existing DCIM folder, change its name or move it to another location before saving a new DCIM folder. IMPORTANT! Never use your computer to edit, delete, move, or rename images stored in the cameras file memory. Doing so can cause problems with the image management data used by the camera, which may make it impossible to display images on the camera or it may cause large error in the number of images value displayed by the camera. Always copy images to your computer before performing any edit, delete, move, or rename operation.

Repairing Casio Exilim EX-Z850 Speaker
This guide will show how to replace the speaker on the Casio camera

2011 iFixit CC BY-NC-SA

www.iFixit.com

Page 1 of 8

Step 1 - Speaker
Remove the four screws on the side with the speaker

Step 2

Remove the four screws from the bottom of the camera. Note: Bottom screws are longer than the top ones, so label accordingly for easy reassembly

Step 3

Remove the four screws on the side opposite of the speaker.

Page 2 of 8

Step 4
Pull apart the bottom casing.

Step 5

Remove ribbon from the rear casing. Set aside rear casing.

Page 3 of 8

Step 6
Use tweezers or prongs to pry the LCD screen off from the opening. Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.

Step 7

Lift up the LCD screen, slowly move it to the other side.

Page 4 of 8

Step 8
Pry off the LCD casing which is taped on to the frame.

Step 9

Flip open the connector holding the ribbon. Pull out the LCD screen with the ribbon from the camera.

Page 5 of 8

Step 10
Pull apart the front casing.

Step 11

Remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off. Slowly pull the side casing so it becomes dislocated from the top of the camera frame.

Page 6 of 8

Step 12
On the front of the camera near the flash flip the connector holding the ribbon. Remove the ribbon from the connector.

Step 13

Carefully remove the L shaped frame from the camera At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab. Pop the frame off the bumps and tabs. Note: There is a yellow and orange wire soldered onto the camera. Be careful not to pull them off. The blue box is the speaker

Page 7 of 8

Step 14
Remove the speaker with tweezers
To reassemble your device, follow these instructions in reverse order.
This document was last generated on Mar 21, 2011.

Page 8 of 8