Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Guidelines for safe battery usage
This notebook uses a Lithium-ion battery. Do not use it in a humid, wet or corrosive environment. Do not put, store or leave your product in or near a heat source, in a high temperature location, in strong direct sunlight, in a microwave oven or in a pressurized container, and do not expose it to temperatures over 60C (140F). Failure to follow these guidelines may cause the battery to leak acid, become hot, explode or ignite and cause injury and/or damage. Do not pierce, open or disassemble the battery. If the battery leaks and you come into contact with the leaked fluids, rinse thoroughly with water and seek medical attention immediately. For safety reasons, and to prolong the lifetime of the battery, charging will not occur at temperatures below 0C (32F) or above 40C (104F). The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and
discharged hundreds of times, but it will eventually wear out. When the operation time becomes noticeably shorter than normal, buy a new battery. Use only Acer approved batteries, and recharge your battery only with Acer approved chargers designated for this device. Use the battery only for its intended purpose. Never use any charger or battery that is damaged. Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip or pen causes direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the connecting object. The capacity and lifetime of the battery will be reduced if the battery is left in hot or cold places, such as in a closed car in summer or winter. Always try to keep the battery between 15C and 25C (59F and 77F). A device with a hot or cold battery may not work temporarily, even when the battery is fully charged. Battery performance is especially limited in temperatures well below freezing. Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose as household waste. Wireless devices may be susceptible to interference from the battery, which could affect performance.

Medical devices

Operation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately shielded from external RF energy or if you have any questions. Switch off your device in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF transmissions.
Pacemakers. Pacemaker manufacturers recommend that a minimum separation of 15.3 centimeters (6 inches) be maintained between wireless devices and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers should do the following:
Always keep the device more than 15.3 centimeters (6 inches) from the pacemaker Not carry the device near your pacemaker when the device is switched o. If you suspect interference, switch off your device, and move it.
Hearing aids. Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.

Vehicles

RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more information, check with the manufacturer, or its representative, of your vehicle or any equipment that has been added. Only qualified personnel should service the device, or install the device in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty that may apply to the device. Check regularly that all wireless equipment in your vehicle is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags inflate with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed, and the air bag inflates, serious injury could result. Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may be illegal.

Switch off your device when in any area with a potentially explosive atmosphere and obey all signs and instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust or metal powders.

Emergency calls

Warning: You cannot make emergency calls through this device. To make an emergency call you shall dial out through your mobile phone or other telephone call system.

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit http://global.acer.com/about/sustainability.htm

Mercury advisory

For projectors or electronic products containing an LCD/CRT monitor or display: Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal information, check www.lamprecycle.org.
ENERGY STAR is a government program (public/private partnership) that gives people the power to protect the environment in a cost effective way and without sacrificing quality or product features. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the US Environmental Protection Agency (EPA) and the US Department of Energy (DOE). In the average home, 75% of all electricity used to power home electronics is consumed while the products are turned off. ENERGY STAR qualified home electronic products in the off position use up to 50% less energy than conventional equipment. More information refers to http://www.energystar.gov and http://www.energystar.gov/powermangement. As an ENERGY STAR partner, Acer Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. This product has been shipped enabled for power management:

Acer eNet Management

Acer eNet Management helps you quickly connect to both wired and wireless networks in a variety of locations. To access this utility, select "Acer eNet Management" from the Empowering Technology toolbar or run the program from the Acer Empowering Technology program group in Start menu. You can also set Acer eNet Management to start automatically when you boot up your PC. Acer eNet Management automatically detects the best settings for a new location, while offering you the option to manually adjust the settings to match your needs.
Acer eNet Management can save network settings for a location to a profile, and automatically switch to the appropriate profile when you move from one location to another. Settings stored include network connection settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings. Security and safety concerns mean that Acer eNet Management does not store username and password information.

Acer ePower Management

Acer ePower Management features a straightforward user interface for configuring your power management options. To access this utility, select "Acer ePower Management" from the Empowering Technology toolbar, run the program from the Acer Empowering Technology program group in Start menu, or right-click the Windows power icon in the system tray and select "Acer ePower Management".

Using power plans

Acer ePower Management comes with three predefined power plans: Balanced, High performance and Power saver. You can also create customized power plans. You can create, switch between, edit, delete and restore power plans, as described below. View and adjust settings for On Battery and Plugged In modes by clicking the appropriate tabs. You can open Windows power options by clicking "More Power Options".
Note: You cannot delete the predefined power plans.
To create a new power plan:
Creating customized power plans allows you to save and quickly switch to a personalized set of power options. 5 Click the Create Power Plan icon. Enter a name for your new power plan. Choose a predefined power plan to base your customized plan on. If necessary, change the display and sleep settings you want your computer to use. Click "OK" to save your new power plan.
To switch between power plans:
Select the power plan you wish to switch to from the drop-down list. Click "Apply".

To edit a power plan:

Editing a power plan allows you to adjust system settings like LCD brightness and CPU speed. You can also turn on/off system components to extend battery life. Switch to the power plan you wish to edit Adjust settings as required.

To use Acer eLock Management, the Empowering Technology password must be set first. Once set, you can apply locks to any of the devices types. Lock(s) will immediately be set without any reboot necessary, and will remain after rebooting, until removed.
Note: If you lose the Empowering Technology password, there is no method to reset it except by reformatting your system. Make sure to remember or write down your password.
Acer eRecovery Management
Acer eRecovery Management is a versatile backup utility. It allows you to create full or incremental backups, burn the factory default image to optical disc, and restore from previously created backups or reinstall applications and drivers. By default, user-created backups are stored to the D:\ drive. Acer eRecovery Management provides you with:
Password protection (Empowering Technology password) Full and incremental backups to hard disk or optical disc Creation of backups:
Factory default image User backup image Current system configuration Application backup
Restore and recovery: Factory default image User backup image From previously-created CD/DVD Reinstall applications/drivers
For more information, please refer to "Acer eRecovery Management" on page 59 in the AcerSystem User's Guide.
Note: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery Management's "System backup to optical disc" feature to burn a backup image to CD or DVD. To ensure the best results when recovering your system using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications, set BIOS passwords and modify boot options. Acer eSettings Management also:
Provides a simple graphical user interface for navigation. Prints and saves hardware specifications. Lets you set an asset tag for your system.

Windows Mobility Center

The Windows Mobility Center collects key mobile-related system settings in one easy-to-find place, so you can quickly configure your Acer system to fit the situation as you change locations, networks or activities. Settings include display brightness, power plan, volume, wireless networking on/off, external display settings, display orientation and synchronization status. Windows Mobility Center also includes Acer-specific settings like Bluetooth Add Device (if applicable), sharing folders overview/sharing service on or off, and a shortcut to the Acer user guide, drivers and utilities. To launch Windows Mobility Center:

Use the shortcut key <

> + <X>

Start Windows Mobility Center from the Control panel Start Windows Mobility Center from the Accessories program group in the Start menu

English

After setting up your computer as illustrated in the Just for Starters. poster, let us show you around your new Acer notebook.

Front view

Item Acer Crystal Eye Display screen Acer FineTouch Keyboard
Description Web camera for video communication (for selected models). Also called Liquid-Crystal Display (LCD), displays computer output. For entering data into your computer.
# 4 Item Acer FineTrack Description Touch-sensitive pointing device which functions like a computer mouse when used together with the click buttons. See FineTrack basics on page 26 for more details. Internal microphone for sound recording. The center button serves as Acer Bio-Protection fingerprint reader supporting Acer FingerNav 4-way control function. (for selected models). Touch-sensitive pointing device which functions like a computer mouse. Light-Emitting Diodes (LEDs) that light up to show the status of the computer's functions and components. See Indicators on page 24 for more details. Left and right speakers deliver stereo audio output. The left and right buttons function like the left and right mouse buttons; the center button serves as a 4way scroll button. Comfortable support area for your hands when you use the computer. Function like the left and right mouse buttons when used together with the center-keyboard FineTrack. See FineTrack basics on page 26 for more details. Turns the computer on and off. Buttons for launching frequently used programs. See "Easy-launch buttons" on page 25 for more details.
Microphone Acer BioProtection Touchpad Status indicators

7 8/ 15 9

speakers
10/ Click buttons 11 (left, center and right) Palmrest FinTrack buttons (left and right) Power button Easy-launch buttons

Closed front view

Indicators

The computer has eight easy-to-read status indicators, including five on the front panel.
The power, battery and wireless communication status indicators are visible even when the LCD display is closed. Icon Function Description Caps Lock Num Lock HDD Wireless LAN Bluetooth Battery Power Lights up when Caps Lock is activated. Lights up when Num Lock is activated. Indicates when the hard disk drive is active. Indicates the status of wireless LAN communication. Indicates the status of Bluetooth communication. Indicates the computer's batttery status. Indicates the computer's power status.
1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.

Easy-launch buttons

Located above the keyboard are four buttons. These buttons are called easy-launch buttons. They are: Empowering Key < programmable button, Internet and email. >, one user-
Press < > to run the Acer Empowering Technology. Please see "Acer Empowering Technology" on page 1. The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To set the Web browser, mail and programmable buttons, run the Acer Launch Manager. See "Launch Manager" on page 37.

Easy-launch button

Default application Acer Empowering Technology (user-programmable)

Internet Email

User-programmable Internet browser (user-programmable) Email application (user-programmable)
FineTrack and FineTrack buttons
The built-in FineTrack is a pointing device that senses movement on its surface. This means the cursor responds as you use your finger to move the FineTrack. Its central location on the keyboard provides optimum comfort and support.
The following items show you how to use the FineTrack and FineTrack buttons:
Using your finger, apply light, steady force on the FineTrack (1) to move the cursor. Press the FineTrack left (2) and right (3) buttons located below the keyboard to perform selection and execution functions. These two FineTrack buttons are similar to the left and right buttons on a mouse.

Note: To activate the BIOS utility, press <F2> during POST.
To start the recovery process: 3 Restart the system. While the Acer logo is showing, press <Alt> + <F10> at the same time to enter the recovery process. Refer to the onscreen instructions to perform system recovery.
Important! This feature occupies 10 GB in a hidden partition on your hard disk.

Requesting service

International Travelers Warranty (ITW)
Your computer is backed by an International Travelers Warranty (ITW) that gives you security and peace of mind when traveling. Our worldwide network of service centers are there to give you a helping hand. An ITW passport comes with your computer. This passport contains all you need to know about the ITW program. A list of available, authorized service centers is in this handy booklet. Read this passport thoroughly. Always have your ITW passport on hand, especially when you travel, to receive the benefits from our support centers. Place your proof-of-purchase in the flap located inside the front cover of the ITW passport. If the country you are traveling in does not have an Acer-authorized ITW service site, you can still get in contact with our offices worldwide. Please consult http://global.acer.com.

Before you call

Please have the following information available when you call Acer for online service, and please be at your computer when you call. With your support, we can reduce the amount of time a call takes and help solve your problems efficiently. If there are error messages or beeps reported by your computer, write them down as they appear on the screen (or the number and sequence in the case of beeps). You are required to provide the following information: Name: _____________________________________________ Address: ___________________________________________ Telephone number: _________________________________ Machine and model type: ____________________________ Serial number: ______________________________________ Date of purchase: ___________________________________
The computer uses a battery pack that gives you long use between charges.
Battery pack characteristics
The battery pack has the following characteristics: Employs current battery technology standards. Delivers a battery-low warning.
The battery is recharged whenever you connect the computer to the AC adapter. Your computer supports charge-in-use, enabling you to recharge the battery while you continue to operate the computer. However, recharging with the computer turned off results in a significantly faster charge time. The battery will come in handy when you travel or during a power failure. It is advisable to have an extra fully charged battery pack available as backup. Contact your dealer for details on ordering a spare battery pack.

Charging the battery

To charge the battery, first make sure that it is correctly installed in the battery bay. Plug the AC adapter into the computer, and connect to a mains power outlet. You can continue to operate your computer on AC power while your battery is charging. However, charging the battery with the computer turned off results in a significantly faster charge time.
Note: You are advised to charge the battery before retiring for the day. Charging the battery overnight before traveling enables you to start the next day with a fully charged battery.
Checking the battery level
The Windows power meter indicates the current battery level. Rest the cursor over the battery/power icon on the taskbar to see the battery's present charge level.

Optimising battery life

Optimizing battery life helps you get the most out of battery operation, prolonging the charge/recharge cycle and improving recharging efficiency. You are advised to follow the suggestions set out below: Purchase an extra battery pack. Use AC power whenever possible, reserving battery for on-the-go use. Eject a PC Card if it is not being used, as it will continue to draw power (for selected model). Store the battery pack in a cool, dry place. The recommended temperature is 10C to 30C. Higher temperatures cause the battery to self-discharge faster. Excessive recharging decreases the battery life. Look after your AC adapter and battery.
To remove a battery pack:

Battery-low warning

When using battery power pay attention to the Windows power meter.
Warning: Connect the AC adapter as soon as possible after the battery-low warning appears. Data will be lost if the battery to become fully depleted and the computer shuts down.
When the battery-low warning appears, the recommended course of action depends on your situation:
Situation The AC adapter and a power outlet are available. Recommended Action 1. Plug the AC adapter into the computer, and then connect to the mains power supply. 2. Save all necessary files. 3. Resume work. Turn off the computer if you want to recharge the battery rapidly. 1. Save all necessary files. 2. Close all applications. 3. Shut down the operating system to turn off the computer. 4. Replace the battery pack. 5. Turn on the computer and resume work. The AC adapter or a power outlet is unavailable. You have no spare battery pack. 1. Save all necessary files. 2. Close all applications. 3. Shut down the operating system to turn off the computer.

What to bring to meetings
If your meeting is relatively short, you probably do not need to bring anything with you other than your computer. If your meeting will be longer, or if your battery is not fully charged, you may want to bring the AC adapter with you to plug in your computer in the meeting room. If the meeting room does not have an electrical outlet, reduce the drain on the battery by putting the computer in Sleep mode. Press <Fn> + <F4> or close the display cover whenever you are not actively using the computer. To resume, open the display (if closed), then press and release the power button.

Taking the computer home

When you are moving from your office to your home or vice versa.
After disconnecting the computer from your desktop, follow these steps to prepare the computer for the trip home:
Check that you have removed all media and compact disks from the drive(s). Failure to remove the media can damage the drive head. Pack the computer in a protective case that can prevent the computer from sliding around and cushion it if it should fall.
Caution: Avoid packing items next to the top cover of the computer. Pressure against the top cover can damage the screen.

What to take with you

Unless you have some items at home, take the following items with you:
AC adapter and power cord The printed User's Guide

Special considerations

Follow these guidelines to protect your computer while traveling to and from work:
Minimize the effects of temperature changes by keeping the computer with you. If you need to stop for an extended period of time and cannot carry the computer with you, leave the computer in the trunk of the car to avoid exposing the computer to excessive heat. Changes in temperature and humidity can cause condensation. Allow the computer to return to room temperature, and inspect the screen for condensation before turning on the computer. If the temperature change is greater than 10 C (18 F), allow the computer to come to room temperature slowly. If possible, leave the computer for 30 minutes in an environment with a temperature between outside and room temperature.

Note: Refer to your card's manual for details on how to install and use the card, and its functions.

Inserting a PC Card

Insert the card into the slot and make the proper connections (e.g., network cable), if necessary. See your card manual for details.

Ejecting a PC Card

Before ejecting a PC Card: 3 Exit the application using the card. Left-click on the PC Card icon on the taskbar and stop the card operation. Press the slot eject button to pop out the eject button; then press it again to eject the card.

ExpressCard

The ExpressCard is the newest version of the PC Card. It is a smaller and faster interface that further enhances the usability and expandability of your computer. ExpressCards support a vast number of expansion options, including flash memory card adapters, TV-tuners, Bluetooth connectivity and IEEE 1394B adapters. ExpressCards support USB 2.0 and PCI Express applications.
Important! There are two types, ExpressCard/54 and ExpressCard/ 34 (54mm and 34mm), each with different functions. Not all ExpressCard slots will support both types. Please refer to your card's manual for details on how to install and use the card, and its functions.

Inserting an ExpressCard

Insert the card into the slot and push gently until it clicks into position.

EXPRESS CARD

Ejecting an ExpressCard
Before ejecting an ExpressCard: 3 Exit the application using the card. Left-click on the remove hardware icon on the taskbar and stop the card operation. Push the card gently into the slot and release to pop out the card. Then pull the card free from the slot.

Installing memory

Follow these steps to install memory: 3 Turn off the computer, unplug the AC adapter (if connected) and remove the battery pack. Then turn the computer over to access its base. Remove the screws from the memory cover; then lift up and remove the memory cover. (a) Insert the memory module diagonally into the slot, then (b) gently press it down until it clicks into place.

"U.S Patent Nos. 4,631,603; 4,819,098; 4,907,093; 5,315,448; and 6,516,132." This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Note: Below regulatory information is for models with wireless LAN and/or Bluetooth only.

General

This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules). Below information is for products with such devices.

European Union (EU)

R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard: Article 3.1(a) Health and Safety
EN60950-1:2001 EN50371:2002 EN50360:2002 (Applied to models with 3G function) EN301 489-1 V1.4.1:2002 EN301 489-17 V1.2.1:2002 EN301 489-3 V1.4.1:2002 (Applied to models with 27MHz wireless mouse/keyboard) EN301 489-7 V1.2.1:2002 (Applied to models with 3G function) EN301 489-24 V1.2.1:2002 (Applied to models with 3G function) ENV1.5.1:2004 ENV1.2.3:2003 EN300 220-1 V1.3.1:2000 (Applied to models with 27MHz wireless mouse/keyboard) EN300 220-3 V1.1.1:2000 (Applied to models with 27MHz

Article 3.1(b) EMC

Article 3.2 Spectrum Usages
Radio device regulatory notice
70 wireless mouse/keyboard)
ENV9.0.2:2003 (Applied to models with 3G function) EN301 908-1 V2.2.1:2003 (Applied to models with 3G function). EN301 908-2 V2.2.1:2003 (Applied to models with 3G function).
The FCC RF safety requirement
The radiated output power of the wireless LAN Mini PCI Card and Bluetooth card is far below the FCC radio frequency exposure limits. Nevertheless, the notebook PC series shall be used in such a manner that the potential for human contact during normal operation is minimized as follows: 1 Users are requested to follow the RF safety instructions on wireless option devices that are included in the user's manual of each RF option device.
Caution: To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm (8 inches) must be maintained between the antenna for the integrated wireless LAN Mini PCI Card built in to the screen section and all persons.
Note: The Acer wireless Mini PCI adapter implements a transmission diversity function. The function does not emit radio frequencies simultaneously from both antennas. One of the antennas is selected automatically or manually (by users) to ensure good quality radiocommunication.

Infrared port/CIR receiver

Line-in jack

Microphone-in jack
Accepts input from external microphones.
Headphones/speaker/ line-out jack with S/ PDIF support Power indicator
Connects to audio line-out devices (e.g., speakers, headphones).
Indicates the computers power status.

Battery indicator

Indicates the computers battery status.
Bluetooth communication button/ indicator Wireless communication button/ indicator
Enables/disables the Bluetooth function. Indicates the status of Bluetooth communication. Enables/disables the wireless function. Indicates the status of wireless LAN communication.

Left View

Item USB 2.0 ports
Description Connects to USB 2.0 devices (e.g., USB mouse, USB camera). Connects to a phone line.

Modem (RJ-11) port

Optical drive
Internal optical drive; accepts CDs or DVDs (slot-load or tray-load depending on model). Lights up when the optical drive is active. Ejects the optical disk from the drive. Ejects the optical drive tray when the computer is turned off. Locks and releases the lid.
Optical disk access indicator Optical drive eject button Emergency eject hole Latch

Right View

Icon Latch
Description Locks and releases the lid. Accepts Secure Digital (SD), MultiMediaCard (MMC), Memory Stick (MS), Memory Stick PRO (MS PRO), xDPicture Card (xD).

5-in-1 card reader

3 USB 2.0 ports
Connect to USB 2.0 devices (e.g., USB mouse, USB camera). Connects to IEEE 1394 devices.

4-pin IEEE 1394 port

PC Card slot eject button PC Card slot
Ejects the PC Card from the slot. Accepts one Type II PC Card.

Express Card/54 slot

Accepts and ExpressCard/34 module Note: ExpressCards are third generation of PC cards, hot-swapable and smaller than previous PC Cards. Designed for both desktop and mobile use, ExpressCards use either USB 2.0 or a single lane PCI Express technology that provides 500 Mbytes/sec total throughput. Formerly code named "NEWCARD," ExpressCards are 5 mm thick like Type II PC Cards, but do not use the same 86x54 mm footprint. ExpressCards come in 75x54 mm and 75x34 mm sizes. Express Card/54 slot means this notebook accepts 75x54mm ExpressCards.

Rear view

Item DC-in jack
Description Connects to an AC adapter.

TV-in port AV-in port

q q q q q q q

For more information, press the < > key to launch the Empowering Technology menu, then click on the appropriate utility and select the Help function.
Acer eDataSecurity Management
Acer eDataSecurity Management is handy file encryption utility that protexts your files from being accessed by unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and
easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messager and Microsoft Outlook. There are two passwords that can be used to encrypt/decrypt a file; the supervisor passowrd and the filespecific password. The supervisor passwork is a master password that cna decrypt any file on your system; the file-specific password will be used to encrypt files by default, or you cna choose to enter your own filespecific password when encrypting a file. NOTE: The password used encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the supervisor password is the only other key capable of decrypting the file. If you lose both passwords, there will be no way to decrypt your encryped file! Be sure to safeguard all related passwords!

Acer eLock Management

Acer eLock Management is a security utility that allows you to lock up your removable data, optical and floppy drives to ensure that data cant be stolen while your notebook is unattended. Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives, USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be mounted as a file system when plugged into the system. Optical drive deivces - includes any kind of CD-ROM or DVD-ROM drives. Floppy disk drives - 3.5-inch disks only.
To activate Acer eLock Management, a password must be set first. Once set, you may apply lock to any of the three kinds of devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked after rebooting, until unlocked. If you do not set a password, Acer eLock Management will reset back to the initial status with all locks removed. NOTE: If you lose your password, there is no method to reset it except by reformatting your notebook or taking your notebook to anAcer Customer Serivce Center. Be sure to remember or write down your password.

Click the right icon to zoom in/out or reset the current view.
Click VisageON to display a menu that allows to change the configuration of the camera, face tracking and video effects settings.
Using video effects (selected models only) The Video Settings section allows you to select an avatar or accessory video effect from the list. To select an effect: 1. Click the encircled icon to display the available video effects. The Video Effect Selection window appears as below:
Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window.
NOTE: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow screen instructions in the VisageON to continue. NOTE: You may use video effects when using the camera for IM chat/video sessions or call conferences.
Using the System Utilities
NOTE: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on the same screen. To access this function, please go to Start>All Programs and click on Acer GridVista. You may choose any one of the four display settings indicated below:
Double (verticle), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display compatible, allowing two displays to be partitioned indepently. Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. AcerGridVista is imple to set up: 1. 2. 3. Run Acer GridVista and select your preferred screen configuration for each display from the task bar. Drag and drop each window into the appropriate grid. Enjoy the convenience of a well-organized desktop.

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be reversed. LAN Interface
Item Chipset Supports LAN protocol LAN connector type LAN connector location Realtek 8110CL 10/100Mbps RJ45 Right side Specification

LAN Interface

Item Features Specification Integrated 10/100 BASE-T transceiver Wake on LAN support compliant with ACPI 2.0 PCI v2.2

Modem Interface

Item Data modem data baud rate (bps) Supports modem protocol Modem connector type Modem connector location 56K V.92 RJ11 Right side Specification

Bluetooth Interface

Item Chipset Data throughput Protocol Interface Connector type Built-in ICH6-M 723 bps (full speed data rate) Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG specification is ratified). USB 1.1 Mini-USB Specification
Wireless Module 802.11b/g (optional device)
Item Chipset Data throughput Protocol Interface Built-in ICH6-M 11~54 Mbps 802.11b+g Mini-PCI type II Specification
Hard Disk Drive Interface
Item Vendor & Model Name Seagate 40G ST9402112A Toshiba MK4025GAS Hitachi HTS421240H9AT00 WD WD400UE-22HCT0 Samsung M40MP0402H Seagate ST96812A Seagate ST960821A Toshiba MK6025GAS HGST HTS541260H9AT00 WD WD600UE-22HCT0 TOSHIBA MK8025GAS HITACHI HTS421280H9AT00 SEAGATE ST9808210A SEAGATE ST98823A TOSHIBA MK8026GAX HGST HTS541280H9AT00 WD WD800UE-22HCT(for Hitachi) 3 (for Seagate)
Capacity (MB) Bytes per sector Data heads Drive Format Disks Spindle speed (RPM)
3 (for Hitachi and Seagate) 4 (for Toshiba)
Performance Specifications Buffer size 2048KB 8192KB 8192KB
Item Interface Max. media transfer rate (disk-buffer, Mbytes/s) Data transfer rate (host~buffer, Mbytes/s) ATA/ATAPI-6; ATA-ATA/ATAPI-6; ATA-ATA/ATA-6; ATA-6 350
100 MB/Sec. Ultra DMA mode-5
DC Power Requirements Voltage tolerance 5V(DC) +/- 5% 5V(DC) +/- 5% 5V(DC) +/- 5%

Combo Drive Interface

Item Vendor & model name Performance Specification Transfer rate (KB/sec) Buffer Memory Interface Applicable disc format DVD/CDRW HLDS GCC-4244N With CD Diskette Sustained: Max 3.6Mbytes/sec 2MB Enhanced IDE(ATAPI) compatible DVD: DVD-ROM, (DVD-5, DVD-9, DVD-10, DVD-18),DVD-R (read, single border), DVD-RW, DVD-RAM (2.6GB, 4.7GB) CD: CD-DA, CD-ROM, CD-ROM XA, CD-R, CD-RW Photo (Multisession) Video CD, CD-Extra, (CD+), CD-test Load: Manual Release: (a) Electrical Release (Release Button) (b) Release by ATAPI command (c) Emergency Release With DVD Diskette Sustained: Max 10.8Mbytes/sec Specification

Loading mechanism

Option

Clear or Set Clear or Set Clear or Set

Set User Password

Set HDD Password

Password on Boot

Disabled or Enabled
Current TPM State Change TPM State
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Dont forget your password. If you forget your password, you may have to return your notebook computer to your dealer to reset it.

Password Conventions

All the passwords must obey the following rules:
All the passwords can be set/cleared in BIOS Setup Security screen. The password entry consists up to 8 alphanumeric characters. At least 1 character must be assigned in this field.
The valid keys are listed in the table below:
Symbol Character AZ 09 = [ ]. , ;
Symbol Name Alphabet A through Z (Not Case Sensitive) Numeric Characters Dash Equals Sign Left Bracket Right Bracket Period Comma Semi-colon

Symbol Character / \

Symbol Name Slash Back-slash
The maximum cycles to retry password is limited to 3. User cannot change/remove password during resuming from S4. Finger print: support 10 fingers - Upack/Authentec modules.

Setting a Password

Perform the following steps to set the supervisor, user, or HDD password. NOTE: The following example uses the Supervisor Password screens. The User and HDD Password screens are identical. 1. Use the and keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears:
Type a password in the Enter New Password field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the Confirm New Password field.
IMPORTANT:Be careful when typing the password as the characters do not appear on the screen. 3. 4. 5. Press Enter. After setting the password, the computer sets the Supervisor Password Is parameter to Set. If desired, you can opt to enable the Password on Boot parameter. When you are done, save the changes and exit the BIOS Setup Utility.

Removing a Password

Follow these steps: 1. Use the and keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears:

2. 3. 4.

Type the current password in the Enter Current Password field and press Enter. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to Clear. When you have changed the settings, save the changes and exit the BIOS Setup Utility.

Changing a Password

1. Use the and keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears:

2. 3. 4. 5. 6.

Type the current password in the Enter Current Password field and press Enter. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. Press Enter. After setting the password, the computer sets the Supervisor Password Is parameter to Set. If desired, you can enable the Password on Boot parameter. When you are done, save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses Enter. If the current password entered does not match the actual current password, the screen will show you the Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following message.
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Boot Boot Priority Order: 1: IDE0: WDC WD200EB - (PM) 2: IDE1: WDC WD200EB - (PM) 3: CD/DVD 4: Network Boot 5: USB HDD 6: USB FDD 7: USB Key 8: USB CD/DVD ROM Menu Level Help Item
Use or to select a device, then press <F6> to move it up the List, or <F5> to move it down the list. Press <Esc> to escape the menu
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
Phoenix - Award WorkstationBIOS CMOS Setup Utility Exit Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Menu Level Help Item
The table below describes the parameters in this screen.
Parameter Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes

Turn the keyboard over, as shown, to expose the cables.
Using fine tweezers, release the first cable lock as shown and remove the cable from the socket.
Using fine tweezers, release the second cable lock as shown and remove the cable from the socket.
Remove keyboard from chassis.
Disconnecting the TouchPad
1. Disconnect the first cable by releasing the locking latch and removing the cable as shown.
2. Disconnect the second cable by releasing the locking latch and removing the cable as shown. NOTE: Move the cable away from the work area to allow access to the third cable.
Disconnect the third cable as shown.
Removing the Switch Board
Remove the Switch Board from the chassis.
Removing the Modem Module
1. Disconnect the two cables from the Modem Module as shown.
Locate and remove the two securing screws as shown.
Lift the Modem Module clear of the chassis.
Removing the Antenna Cables
1. Remove the Antenna Cables from the securing pins as shown.
Pull the three Antenna Cables from the underside of the computer through the mainboard as shown.

Removing the LCM Module

CAUTION: Ensure all cables are removed from securing pins before proceeding to avoid damage. 1. Disconnect the LCM Module cable as shown.
Locate and remove the four screws as shown.
Lift the LCM Module upward to remove from the chassis.

Removing the TouchPad

1. Lift the rear edge of the TouchPad Module first, as shown, then pull the module away from the mounting to clear the ports at the front of the computer.

Removing the Mainboard

1. Locate the three connectors (yellow markers) as shown.
Disconnect the connectors using tweezers as shown.
Locate and remove the two screws as shown to release the Mainboard.
4. Grip the mainboard from the front and lift up. NOTE: If any resistance is met while removing the mainboard, ease the computer case outward to clear the obstruction.
Lift the mainboard clear of the chassis.

Removing the I/O Board

Lift the board toward the front of the computer to clear the port and remove from the chassis.
Removing the Heatsink and Fan Module
1. Turn the mainboard over. Locate and remove the five screws (red markers) and fan connector (yellow marker) from the mainboard.
Remove the Heatsink securing bracket as shown.
Remove the Heatsink as shown.
Steady the Mainboard with one hand and remove the Fan Module by lifting straight up.

Connect the LCM Module cable to the connector on the chassis as shown.

Replacing the Modem

1. Place the Modem in the mounting as shown. Insert the two screws provided to hold the Modem in place.
Reconnect the Modem cables as shown.
Replacing the Switch Board
1. Place the Switch Board in the mounting as shown.
Secure the Switch Board in place using the screw provided.
Reconnecting the TouchPad
1. Replace the connector as shown.
Insert the first cable as shown and lock the latch to secure the cable in place.
Insert the second cable as shown and lock the latch to secure the cable in place.

Replacing the Keyboard

1. Using fine tweezers, insert the thicker cable into the socket and secure the locking latch as shown.
Using fine tweezers, insert the remaining cable into the socket and secure the locking latch as shown.
Turn the keyboard over and place the front edge first into the mounting.
Push the Keyboard into place toward the TouchPad and secure using the two screws provided.
Turn the Computer over and insert the screw as shown.
Replacing the Switch Cover
1. Turn the computer over. Place the Switch Cover as shown and press down until no gaps are visible between the cover and the chassis.
Close the LCM Module. Locate and replace the two screws as shown.
Replacing the Dummy Trays
1. Insert Dummy Tray 2 and push into the slot until flush with the chassis cover.
Insert Dummy Tray 1 and push into the slot until flush with the chassis cover.

Replacing the ODD

1. Insert the ODD and push into the slot until flush with the chassis cover.
Replacing the Wireless Card
1. Ensure the card is positioned label upwards as shown and push into the connector. NOTE: The card remains at an angle until the screws are inserted.
Secure the card in position using the two screws provided.
Reconnect the three Antenna Cables as shown, pushing down firmly to connect the cables.
Cable Color No Tape White Tape Red Tape

Connector Number 3

Replacing the Memory Module

1. Push the memory module into the socket and press downward until it clicks into place.

Replacing the HDD

1. Place the HDD in the mounting, rear edge first as shown.
Push firmly toward the connector to secure the HDD.

Replacing the Covers

1. Replace the HDD cover as shown.
Replace the two screws to secure the cover in place.
Replace the memory cover as shown.
Replace the seventeen (17) screws to secure the cover in place.
Replacing the Battery Pack
1. Place the battery in the cradle rear edge first as shown.
Push the battery downward until it clicks in to place.
Engage the battery lock as shown.
Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. 2. 3. Obtain the failing symptoms in as much detail as possible. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Power failure. (The power indicator does not go on or stay on.) POST does not complete. No beep or error codes are indicated. POST detects an error and displayed messages on screen. Other symptoms (i.e. LCD display problems or others). Symptoms cannot be re-created (intermittent problems).
Go To Power System Check on page 99. Power-On Self-Test (POST) Error Message on page 102 Undetermined Problems on page 114 Error Message List on page 103 Power-On Self-Test (POST) Error Message on page 102 Use the customer-reported symptoms and go to Power-On Self-Test (POST) Error Message on page 102 Intermittent Problems on page 113 Undetermined Problems on page 114

System Check Procedures

External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. 2. 3. Boot from the diagnostics diskette and start the diagnostics program. See if FDD Test is passed as the program runs to FDD Test. Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board. If the error still remains: 1. 2. 3. Reconnect the external diskette drive/DVD-ROM module. Replace the external diskette drive/CD-ROM module. Replace the main board.

External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail. Do the following to select the test device: 1. 2. 3. Boot from the diagnostics diskette and start the diagnostics program. See if CD-ROM Test is passed when the program runs to CD-ROM Test. Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains: 1. 2. 3. Reconnect the external diskette drive/CD-ROM module. Replace the external diskette drive/CD-ROM module. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested. If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board. If the keyboard cable connection is correct, run the Keyboard Test. If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a non-defective FRU: 1. 2. 3. Reconnect the keyboard cables. Replace the keyboard. Replace the main board.
The following auxiliary input devices are supported by this computer:
Numeric keypad External keyboard Chapter 4
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.

Memory check

Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. 2. 3. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board. Go to the diagnostic memory in the test items. Press F2 in the test items.
4. Follow the instructions in the message window. NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.

Power System Check

To verify the symptom of the problem, power on the computer using each of the following power sources: 1. 2. 3. Remove the battery pack. Connect the power adapter and check that power is supplied. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
Check the Power Adapter on page 100 Check the Battery Pack on page 101

Check the Power Adapter

Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure
Pin 1: +19 to +20.5V Pin 2: 0V, Ground

If the voltage is not correct, replace the power adapter. If the voltage is within the range, do the following:
Replace the System board. If the problem is not corrected, see Undetermined Problems on page 114.
If the voltage is not correct, go to the next step. NOTE: An audible noise from the power adapter does not always indicate a defect. 3. 4. If the power-on indicator does not light up, check the power cord of the power adapter for correct continuity and installation. If the operational charge does not work, see Check the Battery Pack on page 101.

Check the Battery Pack

To check the battery pack, do the following: From Software: 1. 2. 3. 4. Check out the Power Management in control Panel In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. Repeat the steps 1 and 2, for both battery and adapter. This helps you identify first the problem is on recharging or discharging.
From Hardware: 1. 2. Power off the computer. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the following figure
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. If the battery status indicator does not light up, remove the battery pack and let it return to room temperature. Re-install the battery pack. If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light up, replace the DC/DC charger board.

Touchpad Check

If the touchpad doesnt work, do the following actions one at a time to correct the problem. Do not replace a non-defective FRU: 1. 2. 3. Reconnect the touchpad cables. Replace the touchpad. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem. No service actions are necessary if the pointer movement stops in a short period of time.
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer. If the symptom is not listed, see Undetermined Problems on page 114. The following lists the error messages that the BIOS displays on the screen and the error symptoms classified by function. NOTE: Most of the error messages occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured. NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter Setup and install Setup defaults or correct the error.

Code 8Ch 8Fh 90h 91h 92h 93h 95h 96h 97h 98h 99h 9Ah 9Ch 9Dh 9Eh 9Fh A0h A2h A4h A8h AAh ACh AEh B0h B2h B4h B5h B6h B9h BAh BBh BCh BDh BEh BFh C0h C1h C2h C3h C4h C5h C6h C7h C8h C9h 1 1-2
POST Routine Description Initialize floppy controller Determine number of ATA drives (optional) Initialize hard-disk controllers Initialize local-bus hard-disk controllers Jump to UserPatch2 Build MPTABLE for multi-processor boards Install CD ROM for boot Clear huge ES segment register Fixup Multi Processor table Search for option ROMs. One long, two short beeps on checksum failure. Check for SMART drive (optional) Shadow option ROMs Set up Power Management Initialize security engine (optional) Enable hardware interrupts Determine number of ATA and SCSI drives Set time of day Check key lock Initialize Typematic rate Erase F2 prompt Scan for F2 key stroke Enter SETUP Clear Boot flag Check for errors POST done- prepare to boot operating system One short beep before boot Terminate QuietBoot (optional) Check password (optional) Prepare Boot Initialize DMI parameters Initialize PnP Option ROMs Clear parity checkers Display MultiBoot menu Clear screen (optional) Check virus and backup reminders Try to boot with INT 19 Initialize POST Error Manager (PEM) Initialize error logging Initialize error display function Initialize system error handler PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional)

Code D2h

POST Routine Description Unknown interrupt
Code E0h E1h E2h E3h E4h E5h E6h E7h E8h E9h EAh EBh ECh EDh EEh EFh F0h F1h F2h F3h F4h F5h F6h F7h 1
Beeps Initialize the chipset Initialize the bridge Initialize the CPU Initialize the system timer Initialize system I/O Check force recovery boot Checksum BIOS ROM Go to BIOS Set Huge Segment Initialize Multi Processor Initialize OEM special code Initialize PIC and DMA Initialize Memory type Initialize Memory size Shadow Boot Block System memory test Initialize interrupt vectors Initialize Run Time Clock Initialize video Initialize System Management Mode Output one beep before boot Boot to Mini DOS Clear Huge Segment Boot to Full DOS
Index of Symptom-to-FRU Error Message