MOVE TO THE REQUIRED MENU OPTION/ ADJUST AN OPTION VALUE RESPECTIVELY CONFIRM YOUR CHOICE (STORE OR ENTER) PICTURE EFFECT SELECTION AUTO ADJUSTMENT IN PC MODE SOUND EFFECT SELECTION
PICTURE SIZE PIP FUNCTIONS: - PIP ACTIVATION OR DEACTIVATION (PIP) - SWAPPING THE MAIN AND THE SUB PICTURE (SWAP) - SIZE SELECTION (SIZE) - SOURCE SELECTION (SOURCE)
The performance of the remote control may be affected by bright light.

English - 8

Page 9
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when you: Purchase the PDP Monitor Find that the remote control is no longer operating correctly
Remove the cover on the rear of the remote control by pressing the symbol ( ) downwards and then pulling firmly to remove it. Insert two R03, UM4, AAA 1.5V or equivalent batteries taking care to respect the polarities: - on the battery against - on the remote control + on the battery against + on the remote control Replace the cover by aligning it with the base of the remote control and pressing it back into place. Do not mix battery types, i.e. alkaline and manganese.
Assembling the Stand-Base
Assemble the PDP Monitor with the stand and firmly secure the PDP Monitor using 4 screws provided.
Two or more people should carry the PDP Monitor. Never lay the PDP Monitor on the floor because of possible damage to the screen. Always store the PDP Monitor upright.

English - 9

Page 10
Installing the Display on the Wall Attachment Panel

Installation Notes

Contact a technician for installing the wall bracket. Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Refer to the correct installation guide according to your wall bracket.

Components

Only use the components and accessories shipped with the product. Wall Bracket Hinge Accessories

Plastic Hanger: 4

Left: 1

Right: 1

Anchor : 11

Wall Bracket Assembly

Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall.

Captive Screw

Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4 screws on the wall bracket to adjust the length.

Example for 2x2 Video Wall connections
Rear of the PDP Monitor Rear of the PDP Monitor
You can connect a Composite (Video) without a distributor as you would connect a PC. Select ID input on the menu. Use the numeric buttons to enter the ID for PDP Monitor adjustment. You can operate the remote control only for the PDP Monitor that has been selected. For details about Multiple Display Control, refer to Setting the MDC (Multiple Display Control) on page 29 and the Help section in MDC program CD.
Example for Multiple Display Control connections

English - 12

Page 13

Connecting Speakers

Speakers are optional. You have to purchase the speakers additionally.
Remove the screws on the rear of the PDP Monitor.

PPM42M5S PPM42M5H

PPM50M5H

PPM63M5H

Hang the two T shaped hangers on the square holes on the rear of the PDP Monitor.
PPM42M5S PPM42M5H PPM50M5H
Tighten the PDP Monitor and the speaker bracket using the screws removed from the PDP Monitor.
When moving your PDP Monitor, do NOT hold the speaker connected to your PDP Monitor. It may damage the bracket clamping the speaker and your PDP Monitor together and result in a drop of your PDP Monitor and a risk of personal damage and injury.

English - 13

Page 14
Connecting Speakers (continued)
T Connect the speaker audio cable to the external speaker output jack on the rear of the PDP Monitor matching the + and - ends of the cable with the diagram on the PDP Monitor.
The speakers MUST have a power handling capability of 10 watts minimum (impedance 8). When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it.

Ferrite Cores

The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector.

W se in

English - 14

9:30 AM

Page 15
Switching Your PDP Monitor On and Off
The mains lead is attached to the rear of your PDP Monitor.
Plug the mains lead into an appropriate socket. Result: The Standby indicator on the front of the PDP Monitor lights up.
The main voltage is indicated on the rear of the PDP Monitor and the frequency is 50 or 60Hz.
Press the button on the front of the PDP Monitor (or the ON ( ) button on the remote control) to switch the PDP Monitor on. To switch your PDP Monitor off, press the the OFF ( ) button on the remote control). button again (or

Choosing Your Language

When you start using your PDP Monitor for the first time, you must select the language which will be used for displaying menus and indications.

TV Time Language

Setup : English
Press the MENU ( ) button. The main menu is displayed. Result: Press the or button to select Setup. The Setup menu is displayed. Result:

Return

Press the ENTER (

) button.

TV Time Language PC Setup English : English Franais Deutsch Italiano Espaol Portugus
Press the or button to select Language. Press the ENTER ( ) button. The available languages are listed. Result: Select the appropriate language by pressing the or button. Press the ENTER ( ) button.

English - 15

9:46 AM

Page 16

Changing the Picture Standard
You can select the type of picture which best corresponds to your viewing requirements.
: Normal : Off : 16:9 Enter Return
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move

Picture : Dynamic

Press the MENU ( ) button. The main menu is displayed. Result: Press the or button to select Picture. The Picture menu is displayed. Result: Press the ENTER ( ) button. The Mode is selected. Result: Press the ENTER ( ) button again. The available options are listed. Result: Select the required option by pressing the or button. The following options are available. Result: Dynamic - Standard - Movie - Custom Entertain - Internet - Text - Custom : PC or DVI Mode.
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter
Picture : Dynamic Dynamic Standard : Normal Movie Custom : Off : 16:9
You can also set these options simply by pressing the P.MODE (Picture Mode) button on the remote control.

English - 16

Page 17
Customizing the Picture Settings
Your PDP Monitor has several setting options that allow you to control the picture quality.
Picture : Dynamic : Normal : Off : 16:9 Return

Press the MENU ( ) button. The main menu is displayed. Result: Press the or button to select Picture. The Picture menu is displayed. Result: Press the ENTER ( ) button. The Mode is selected. Result: Press the or button to select Custom. Press the ENTER ( ) button. Select the required option by pressing the or button. The following options are available. Result: Contrast - Brightness - Sharpness - Color Tint (NTSC only) Contrast - Brightness : PC or DVI Mode.
Custom Contrast Brightness Sharpness Color Tint G 55 R 50
Press the ENTER ( Result:

Contrast 100

The horizontal bar is displayed. Press the or button until you reach the optimal setting.
Press the or button to select other option(s). When the picture mode is set to Custom, the settings values may vary depending on the input source. (ex. AV, Component, PC, or DVI.)
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter Return : Off : 16:9 : Normal Picture : Dynamic
Press the MENU ( ) button to return to the Picture menu. Press the or button to select Color Tone. Press the ENTER ( ) button. Select the required option by pressing the or button. Result: The following options are available.
Picture Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter : Normal Cool2 Cool1 : OffNormal : 16:9 Warm1 Warm2 Return : Dynamic
Cool2 - Cool1 - Normal - Warm1 - Warm2 Custom - Cool - Normal - Warm : PC Mode. Cool - Normal - Warm : DVI Mode.

English - 17

Page 18
Adjusting the RGB Color (PC Mode)
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter Return : Off : 16:9 : Custom Picture : Entertain
Preset to the PC mode by pressing the SOURCE (

Press the MENU ( Result:

The main menu is displayed.
Press the or button to select Picture. Result: The Picture menu is displayed. ) button.
Press the or button to select Color Tone. Press the ENTER ( ) button. Press the or button to select Custom. Press the ENTER ( ) button.
Picture : Entertain : Custom : Off : 16:9 Return
This feature is not available when the input source is DVI mode.
Press the or button to select Color Control. Press the ENTER ( ) button. Select the required option (Red, Green, or Blue) by pressing the or button. Press the ENTER ( Result: ) button.

TV Red Green Blue

Color Control 50

Move Enter Return

Press the or button to select other option(s). ) button.

English - 18

Page 19
Setting the Picture (PC Mode)
Preset to the PC mode by pressing the SOURCE ( ) button.
TV Setup Time Language PC : English
Press the or button to select Setup. Result: The Setup menu is displayed. ) button.
Press the or button to select PC. Press the ENTER ( ) button. Result: The PC menu is displayed. ) button again to select Auto Adjustment.

PC Auto Adjustment Image Lock Position Zoom Information
The screen quality and position are automatically reset. The settings are all finished, and the PDP Monitor will automatically return to the previous picture.
Press the or button to select Image Lock. Press the ENTER ( ) button. Press the or button to select the option (Coarse or Fine) to be adjusted. Press the ENTER ( ) button. Result: The horizontal bar is displayed. Press the or button until you reach the optimal setting. i
Auto Adjustment in Progress. Please wait.
TV Auto Adjustment Image Lock Position Zoom Information

TV Coarse Fine

Image Lock

Coarse

English - 19

Page 20

Setting the Picture (PC Mode) (continued)
TV Auto Adjustment Image Lock Position Zoom Information PC
The PC menu is displayed again.
Press the or button to select Position. Press the ENTER ( ) button. Adjust the position by pressing the , , , or button. Press the ENTER ( ) button.

Position

Adjust

English - 20

Page 21
Using Zoom function (PC Mode)
Press the or button to select PC. Press the ENTER ( ) button. Result: The PC menu is displayed.
Press the or button to select Zoom. Press the ENTER ( ) button. Press the ENTER ( ) button again. Select the required option by pressing the or button. Result: The following options are available. 0-1-2-3 -4 -5 -6
Option 0 represents a normal screen. The greater the number, the more magnified the screen. You can select the position and reset functions by selecting options 1 through 6. (If you select option 0, the position and reset functions are not selected.) If you have selected the Zoom function as between 1~6, you will not be able to select the Auto Adjustment function.

TV Zoom Position Reset

Zoom :Move Enter Return
Press the or button to select Position. Press the ENTER ( ) button. Adjust the position by pressing the , , , or button. Press the MENU ( Result: ) button.

Zoom :1

The Zoom menu is displayed again.
To return the factory defaults, select Reset by pressing the or button. Press the ENTER ( ) button. Result: The previously adjusted settings will be reset to the factory defaults.

Zoom Zoom Position Reset :1

English - 21

Page 22
Viewing the PC Information
TV Time Language PC : English Setup
You can view the current resolution and frequency of your pc.
Press the or button to select Information. Press the ENTER ( Result: ) button.
The resolution, vertical frequency and horizontal frequency are displayed. ) button.
TV Resolution H-Frequency V-Frequency Information 1024*768 48.3 KHz 59 Hz

Press the MENU (

English - 22

Page 23

Selecting the Picture Size
You can select the picture size which best corresponds to your viewing requirements.

TV Mode

Picture : Dynamic : Normal : Off : 16:9 Enter Return Custom Color Tone Color Control Film Mode Size PIP
Press the or button to select Size. Press the ENTER ( ) button. Select the required option by pressing the or button. Result: The following options are available. 16:9 : Sets the picture to 16:9 wide mode. Panorama : Use this mode for the wide aspect ratio of a panoramic picture. Zoom1 : The screen size when wide screen is vertically enlarged. Zoom2 : The screen size when the Zoom1 screen is vertically enlarged. 14:9 : Magnify the size of the picture more than 4:3. 4:3 : Sets the picture to 4:3 normal mode.
Size 16:9 Panorama Zoom1 Zoom2 14:9 4:3

PC to DVI Mode

TV 16:9 Panorama Zoom1 Zoom2 14:9 4:3 Size
You can select these options simply by pressing the P.SIZE button on the remote control. If you change the picture size In PIP mode, PIP disappears automatically. Depending on the input source, the P.SIZE options may vary. Check if the Video Wall (refer to page 33) is On if the Picture size is not function. Picture size does not function when the Video Wall is set to On. Change the setting to Off and try it again.
Positioning and Sizing the screen using Zoom
Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction using the or button as well as the screen size. Move the screen up/down using the or button after selecting the by pressing the or button. Screen enlargement operates only in AV/S-Video/Component input modes. In PC or DVI mode, you can select either 16:9 or 4:3.

English - 23

Page 24
Freezing the Current Picture
You can freeze the picture when watching a moving picture simply by pressing the STILL button. To return to normal viewing, press it again.
The Still function in PIP mode will be applied to the main picture and not to the sub picture.
Changing the Sound Standard
You can select the type of special sound effect to be used when watching a given broadcast.

IR Lock : On

English - 27

Page 28

Setting Up Your Personal ID Number
This feature sets viewing restrictions and prevents unauthorized access to your PDP Monitor through the PIN (Personal Identification Number), which is a 4 digit number.
Press the or button to select Safety Lock. Press the ENTER ( ) button. Press the or button to select Change PIN. Press the ENTER ( ) button. Press the number buttons to enter your current 4-digit pin number.
The default pin number for a new PDP Monitor set is 0000.

Change PIN

Press the numeric buttons to enter your new 4-digit pin number. Re-enter your new pin number to confirm.

Enter PIN Enter New PIN

If you forget the pin number, press the remote control buttons in the following sequence, which resets the pin to 0-0-0-0: MUTE, 1, 8, 6.
Enter PIN * * * Enter New PIN *

English - 28

Page 29
Setting the MDC (Multiple Display Control)
This function enables you to easily control the connected monitors on the PC by specifying IDs to connected monitors.
TV Function Screen Burn Protection : Off
Safety Lock Multi Control Video Wall Fan
Press the or button to select Function. Result: The Function menu is displayed.
TV ID Setup Multi Control : : 00 -
Press the or button to select Multi Control. Press the ENTER ( Result: ) button.

ID Input

The Multi Control menu is displayed with the ID Setup selected.
Press the ENTER ( ) button again. Select the ID setup number by pressing the , , or numeric buttons. Press the ENTER ( ) button. Press the or button to select ID Input. Press the ENTER ( ) button. Enter ID input number by using the numeric buttons. Press the ENTER ( ) button.
Multi Control ID Setup ID Input : : 00
To operate the multi control function, PDP1 and PDP2 should be set in the ID Setup mode. When entering the ID Input number of PDP1 while the PDP Monitor is set in the ID Input mode, only PDP1 is switched to the Menu screen and you can operate the remote control. At this time, PDP2 doesn't operate with the remote control and displays the standby mode of ID Input. For further details, refer to the MDC program guide.

TV ID Setup ID Input

When a video input source is from a film such as movies, this feature identifies the source and changes to the corresponding screen.

Y de de

TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter Return : Off Off : 16:9 On : Normal Picture : Dynamic
Press the or button to select Film Mode. Press the ENTER ( ) button. Select Off or On by pressing the or button. Press the ENTER ( ) button.
Automatically senses and processes film signals from all sources and adjusts the picture for optimum quality. Available in AV, S-Video, and Component (480i) modes. Unavailable in PC1, PC2, DVI mode.

English - 38

Page 39
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture of external A/V devices. In this way you can monitor the video input from any connected devices while monitoring other video inputs.
PIP PIP Source Swap Size Position : : : Off Off : PC1 On
Press the or button to select PIP. Press the ENTER ( ) button. Result: The PIP is selected.
Press the ENTER ( ) button again. To activate, set PIP to On by pressing the or button. Press the ENTER ( ) button. Press the or button to select Source. Press the ENTER ( ) button. Result: The following options are available. AV - S-Video - Component - PC1 - PC2 - DVI

Sound Select : Main

TV PIP
PIP : Off AV Source : PC1 S-Video Swap Component Size : PC1 Position : PC2 DVI Sound Select : Main
Select a source of the sub picture by pressing the or button. Press the ENTER ( ) button. Press the or button to select Swap. Press the ENTER ( ) button. Result: The main picture and sub picture are interchanged.
PIP PIP Source Swap Size Position : : : On : PC1
Press the or button to select Size. Press the ENTER ( ) button. Result: The following options are available. (Large) - (Small) - (Double Window) - (Double Wide)
Select a size of the sub picture by pressing the or button. Press the ENTER ( ) button.
PIP PIP Source Swap Size Position : : : On : PC1

English - 39

Page 40
Viewing the Picture in Picture (PIP) (continued)
TV PIP Source Swap Size Position : :

PIP : On : PC1

Press the or button to select Position. Press the ENTER ( ) button. Result: The following options are available. -
The Position menu is available when the Size is large ( ) mode and small ( ) mode.
Select a position of the sub picture by pressing the or button. Press the ENTER ( ) button. Check if the Video Wall (refer to page 33) is On if the PIP On/Off does not function. PIP does not function when the Video Wall is set to On. Change the setting to Off and try it again.

Easy functions of the remote control. Buttons PIP SWAP SIZE SOURCE Feature Used to activate or deactivate the PIP function directly. Used to interchange the main picture and the sub picture. Used to select a size of the sub picture ( (Large), (Small), (Double Window), or (Double Wide)). Used to assign a source of the sub picture (AV, S-Video, Component, PC1, PC2, or DVI).

Table of PIP Settings

Sub Main
X - This PIP combination is not available. O - This PIP combination is available.
S-Video X X X O O X Component X X X O O X PC1 O O O X X O PC2(BNC) O O O X X O DVI X X X O O X

AV X X X O O X

AV S-Video Component PC1 PC2(BNC) DVI

English - 40

Page 41
Listening to the Sound of the Sub Picture
While the PIP feature is activating, you can listen to the sound of the sub picture.
PIP PIP Source Swap Size : : Position : Off Off : PC1 On
Press the ENTER ( ) button. To activate, set PIP to On by pressing the or button. Press the ENTER ( ) button. Press the or button to select Sound Select. Press the ENTER ( ) button. Result: You can listen to the sound of the sub picture.
PIP PIP : On : PC1 : : Source Swap Size Position
To listen the sound of the current main picture, set to Main.
Set to sub by pressing the or button. Press the ENTER ( ) button.
Main Sound Select : Main Sub

English - 41

Page 42
Viewing an External Signal Source
Once you have connected up your various audio and video systems, you can view different sources by selecting the appropriate input.

TV Source List Edit Name

Input : AV
Press the or button to select Input. Result: The Input menu is displayed. ) button.
TV AV S-Video Component PC1 PC2 DVI
Source List :---:---:---:---:---:---
The Source List is selected. ) button again.
Press the or button to select the signal source, press the ENTER ( ) button. Result: The available signal sources are listed.
AV, S-Video, Component, PC1, PC2, or DVI You can also set these options simply by pressing the SOURCE ( ) button on the remote control.

Input : AV

Repeat steps 1 to 3. Result: The Input menu is displayed again.
Press the or button to select Edit Name. Press the ENTER ( ) button. Press the or button to select external source to be edited. Press the ENTER ( ) button. Result: The available device names are listed. VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR (DVD HDD Recorder), or PC

English - 44

Page 45
Connecting to the DVD/DTV Receiver Input

Y / PB / PR

Digital Set-Top Box
The COMPONENT IN (or Y/PB/PR (video) and AUDIO) connectors are used for equipment with a DVD/ DTV Receiver output. (480i, 576i, 480p, 576p, 720p, 1080i)

English - 45

Page 46
Connecting to the DVI Input
The DVI IN (video) and AUDIO connectors are used for equipment with a DVI output.

T P v in

Personal Computer
Connecting to the PC Input
The PC 1 (or PC 2 (BNC) IN) and AUDIO connectors are used for interfacing with your PC.
or Only when watching TV in PC1 mode, you can use the RGB OUT port to connect the current screen to another PDP in the same mode.

English - 46

Page 47
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop,
then click on Properties. The Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode
with reference to the Display Modes Table. You do not need to change the Colours settings.
3 Click on Advanced. A new settings dialog box

will be displayed.

4 Click on the Monitor tab, then set the Screen
refresh rate with reference to the Display Modes Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate.
5 Click on OK to close the window, then Click on
OK button to the Display Properties window. Automatic re-booting may commence at this moment.
6 Shutdown the PC, and connect it to your PDP
Monitor. (Connecting to the PC Input on page 46)
The actual screens on your PC may look different, depending on your particular version of Windows and the type of your PC. When you use your PDP Monitor as a PC monitor, it supports Colours up to 32 bits. In this case, the display on the PDP Monitor may look different depending on your particular version of Windows or the PC manufacturer. When connecting a PC (including the DVI connection), you must set it to the display settings that are supported by the PDP Monitor. Otherwise, the message Out of input range will be displayed.

English - 47

Page 48

Input Mode (PC/DVI)

Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Resolution VGA 640 x x x x 480 Vertical Horizontal PPM42M5S PPM42M5H PPM50M5H PPM63M5H frequency (Hz) frequency (kHz) 60 31.5 37.9 37.9 31.5 37.9 31.5 37.9 37.5 43.3 35.2 37.9 48.1 46.9 53.7 48.4 56.5 60.0 68.7 29.8 35.1 36.0 37.0 31.8 67.5 64.0 80.0 47.7 60.1 47.8 48.2 75.0 / / / / / / / / / / / / / / / / / / / / / / / / / /

T sy ce Se

800 x 600

1024 x 768

848 x 480

SXGA WXGA

852 x x x x x x x 1200

UXGA

mode does not work with DVI mode. The interlace mode is not supported. The PDP might operate abnormally if a non-standard video format is selected. The 1366 x 768 / 852 x 480 mode is only supported by a particular video card (PIXEL PERFECT made by IMAGINE GRAPHICS Ltd.). In 1360 x 768 resolution, the screen displays 1360 pixels horizontally. A mark means that this mode can be supported. A mark means that this mode is recommended.

English - 48

Page 49
Power Saver (PC1 mode only)
This monitor has a built-in power management system called Power Saver. This power management system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. You use a software utility installed on your computer to set up this feature. See the table below for details. Normal Operation Active Active Active Green On Active Inactive Blanked Green Blinking (3 sec Interval) Power-saving Function Mode Suspend Mode Position A1 Power-off Mode Position A2 Inactive Inactive Blanked Green Blinking (3 sec Interval)
State Horizontal Sync Vertical Sync Video Power Indicator
If the horizontal sync is inactive and the vertical sync active, this monitor goes to the screen mute state. This monitor automatically returns to normal operation when horizontal and vertical sync return. This occurs when moving the computers mouse or pressing a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

English - 49

Page 50
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the PDP Monitor and contact your local dealer. No sound or picture Check that the mains lead has been connected to a wall socket. Check that you have pressed the ON or OFF button on the remote control. Check the picture contrast and brightness settings. Check the volume. Check the volume. Check whether the volume MUTE button on the remote control has been pressed. Adjust the color settings. Check that the video system selected is correct. Plug your PDP Monitor into a different mains socket. Replace the remote control batteries. Clean the upper edge of the remote control (transmission window). Check the battery terminals. On your computer check: Power, Signal Cable. The TV is using its power management system. Move the computer's mouse or press any key on the keyboard.

Normal picture but no sound
No picture or black and white picture Sound and picture interference Remote control malfunctions
Screen is black and power indicator light blinks steadily.

English - 50

9/8/05

1:42 PM

Page 51

Technical Specifications

Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. (Class A product only)
Dimensions (W x D x H) Weight (Without stand) Screen aspect ratio Screen size
PPM42M5S/PPM42M5H - 1027 x 79 x 630.5 mm ; 40.43 x 3.11 x 24.82 inches PPM50M5H - 1204.6 x 79 x 724 mm ; 47.43 x 3.11 x 28.5 inches PPM63M5H - 1503.4 x 89 x 893.8 mm ; 59.19 x 3.5 x 35.19 inches PPM42M5S/PPM42M5H - 34.5 kg PPM50M5H - 46.5 kg PPM63M5H - 69 kg 16:9 PPM42M5S/PPM42M5H - 42 inch PPM50M5H - 50 inch PPM63M5H - 63 inch PPM42M5S - 852 x 480 PPM42M5H - 1024 x 768 PPM50M5H/PPM63M5H - 1366 x 768 PAL, SECAM, NTSC (NT3.58/NT4.43) Stereo, Virtual Dolby 10W + 10W (8) U.S.A/Canada - AC110-120V~ 60Hz Other countries - AC100-240V~ 50/60Hz PPM42M5S - 330 Watts PPM42M5H - 380 Watts PPM50M5H - 420 Watts PPM63M5H - 570 Watts VIDEO IN - AV/S-VIDEO COMPONENT IN - Y/PB/PR (RCA, 3P, 480i~1080i) RGB1(PC1) IN - D-SUB, 15P RGB2(PC2) IN VGA~XGA (R/G/B/H/V) DVI IN - DVI-D type VIDEO OUT - VIDEO/L/R (RCA, 3P) VIDEO IN - L/R COMPONENT IN - L/R (RCA, 2P) AUDIO (Stereo jack for RGB1/2(PC1/2) and DVI input, 2 x mini jack) EXT SPEAKER (8) - R+/-, L+/RS232C - IN/OUT (D-SUB, 9P)
Native pixel resolution (H x V) Color systems Sound Audio output power Power supply Power consumption

Video inputs

Monitor outputs Audio inputs
Audio outputs External control

English - 51

Page 52

English - 52

Page 53

English - 53

Page 54

- AFTER SALES SERVICE

- Do not hesitate to contact your retailer or service agent if a change in the performance of your product indicates that a faulty condition may be present.

BN68-00848A-00Eng_0404

4/4/05

3:57 PM

Page 1
PDP-MONITOR (PLASMA DISPLAY PANEL)
PPM42M5S PPM42M5H PPM50M5H PPM63M5H

Owners Instructions

Before operating the unit, please read this manual thoroughly, and retain it for future reference.
Intended for Commercial Use and Operation
ON-SCREEN MENUS Picture In Picture (PIP) VIDEO WALL MDC (Multiple Display Control) Screen Burn Protection Digital Natural Image engine
This device is a Class B digital apparatus. Register your product at www.samsung.com/global/register

Page 2

User Instructions
Screen Image retention Do not display a still image (such as on a video game or when hooking up a PC to this PDP Monitor) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as screen burn. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image. Height The PDP Monitor can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there. Heat on the top of the PDP Monitor The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product. The product is making a cracking noise. A cracking noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit. Cell Defects The PDP Monitor uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product. Avoid operating the PDP Monitor at temperatures below 5C(41F) A still image displayed too long may cause permanent damage to the PDP Monitor Panel Watching the PDP Monitor in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damage caused by the above effect are not covered by the Warranty. Afterimage on the Screen. Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the brightness and contrast when displaying still images for a long time. Warranty - Warranty does not cover any damage caused by image retention. - Burn-in is not covered by the warranty. Installation Be sure to contact an authorized service center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc. Failure to do so may cause a serious damage to your monitor. Installing the product in an airtight place may shorten the lifetime of the product.

English - 2

Page 3

Checking Parts

PPM42M5S/ 42M5H/50M5H
Owners Instructions Remote Control/ AAA Batteries

Power Cord

Stand-Base (2EA)
g Install CD - MDC Software (RS-232C) Ferrite Cores for Speaker Wire (2EA) (Refer to page 14) Screws (4EA) PC Cable

English - 3

Page 4

Contents

FOREWORD

User Instructions....

CONNECTING AND PREPARING YOUR DISPLAY
Control Panel.... Infrared Remote Control... Inserting the Batteries in the Remote Control.. Assembling the Stand-Base... Installing the Display on the Wall Attachment Panel.. Installing the Display Vertically... Before Using the Video Wall and the Multiple Display Control function. Connecting Speakers... Switching Your PDP Monitor On and Off.. Choosing Your Language...

USING YOUR DISPLAY

Changing the Picture Standard... Customizing the Picture Settings.. Adjusting the RGB Color (PC Mode)... Setting the Picture (PC Mode)... Using Zoom function (PC Mode).. Viewing the PC Information... Selecting the Picture Size... Freezing the Current Picture... Changing the Sound Standard... Extra Sound Settings... Activating Panel Button Lock... Activating Remote Control Button Lock.. Setting Up Your Personal ID Number..

English - 4

Page 5

Contents (continued)

USING YOUR DISPLAY (CONTINUED)
Setting the MDC (Multiple Display Control)... Preventing Screen Burn-in... Reducing the Effects of Screen Burn.. Setting the Screen Burn Protection Timer... Setting the Multiple Screen... Displaying the Setting Information... Setting and Displaying the Current Time.. Switching the PDP Monitor On and Off Automatically.. Selecting the Fan... Setting the Film Mode... Viewing the Picture in Picture (PIP)... Listening to the Sound of the Sub Picture... Viewing an External Signal Source...
ADDITIONAL INFORMATION AND CONNECTIONS
Connecting to the Audio/Video Input... Connecting to the S-Video Input... Connecting to the Component Input.. Connecting to the DVD/DTV Receiver Input.. Connecting to the DVI Input... Connecting to the PC Input... Setting up Your PC Software (Windows only).. Input Mode (PC/DVI)... Power Saver (PC1 mode only)...

RECOMMENDATIONS FOR USE

Troubleshooting: Before Contacting Service Personnel.. Technical Specifications... Dimension....

Symbols

Important

English - 5

Page 6

Control Panel

The actual configuration of your PDP Monitor may be different, depending on your model.

Front of the PDP Monitor

c) Speaker Speaker

SOURCE

- Select the external input source. - Store your settings in the menu. - When the Main menu is displayed on screen, the Main menu is not operated with source key.

Power Indicator

- Power Off; Black - Power On; Green
Display the on-screen menu.

Remote Control Sensor

Aim the remote control towards this spot on the PDP Monitor.

- VOL +

- Adjust the volume. - Adjust an option value respectively. (VOL + : Enter to the selected menu.)
Control the cursor in the menu.
Press to turn the PDP Monitor on and off.
You can use the SEL , buttons to switch on the PDP Monitor when it is in standby mode depending on the model. The VOL -, + and SEL , buttons have the same function as the /// buttons on the remote control. If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the PDP Monitor.

Length between the two locking holes
Wall Bracket Hinge (Left)
There are two hinges (left and right). Use the correct one. Hinge (Right)
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws.

English - 10

Page 11
Installing the Display on the Wall Attachment Panel (continued)
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)
Remove the 4 screws on the back of the product.
Insert the screw into the plastic hanger. (See the figure below)
Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. Be careful when installing the product on the bracket as fingers can be caught in the holes. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.
Tighten the 4 screws in step 2 (plastic hanger + screw ) to the rear holes of the product.
Remove safety pin (#) and insert the 4 product holders into the corresponding bracket holes (!). Then place the product (@) so that it is firmly fixed to the bracket. Make sure to reinsert and tighten the safety pin (#) to securely hold the product to the bracket.

PDP Monitor

Wall Bracket Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2 before installing it on the wall.
Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. (See the figure to the right) You can adjust the bracket angle between -2 and 15. Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

English - 11

Page 12
Installing the Display Vertically
You can install the PDP Monitor vertically. In this case, the fan automatically works. If you wish to stop the fan, position the PDP Monitor horizontally and then set Fan to Off in the Function menu. Please use the wall attachment panel exclusively when installing vertically. And you have to put left side of the PDP Monitor on top when viewed from front.

Before Using the Video Wall and the Multiple Display Control function
Example for 2x2 Video Wall function
Please create ID for each PDP Monitor before installing them close together. It may be difficult to create IDs when operating the remote control for PDPs that are installed close to each other. For details about Video Wall configuration and operation, refer to Setting the Multiple Screen on page 33.
Example for 2x2 Video Wall connections
Rear of the PDP Monitor Rear of the PDP Monitor
You can connect a VCR without a distributor as you would connect a PC. Select ID input on the menu. Use the numeric buttons to enter the ID for PDP Monitor adjustment. You can operate the remote control only for the PDP Monitor that has been selected. For details about Multiple Display Control, refer to Setting the MDC (Multiple Display Control) on page 29 and the Help section in MDC program CD.
Example for Multiple Display Control connections

English - 12

Page 13

Connecting Speakers

Speakers are optional. You have to purchase the speakers additionally.
Remove the screws on the rear of the PDP Monitor.

PPM42M5S PPM42M5H

PPM50M5H

PPM63M5H

Hang the two T shaped hangers on the square holes on the rear of the PDP Monitor.
PPM42M5S PPM42M5H PPM50M5H
Tighten the PDP Monitor and the speaker bracket using the screws removed from the PDP Monitor.
When moving your PDP Monitor, do NOT hold the speaker connected to your PDP Monitor. It may damage the bracket clamping the speaker and your PDP Monitor together and result in a drop of your PDP Monitor and a risk of personal damage and injury.

English - 13

Page 14
Connecting Speakers (continued)
T Connect the speaker audio cable to the external speaker output jack on the rear of the PDP Monitor matching the + and - ends of the cable with the diagram on the PDP Monitor.
The speakers MUST have a power handling capability of 10 watts minimum (impedance 8). When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it.

Ferrite Cores

The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector.

W se in

English - 14

3:58 PM

Page 15
Switching Your PDP Monitor On and Off
The mains lead is attached to the rear of your PDP Monitor.
T Front of the PDP Monitor
Plug the mains lead into an appropriate socket. Result: The Standby indicator on the front of the PDP Monitor lights up.
The main voltage is indicated on the rear of the PDP Monitor and the frequency is 50 or 60Hz.
Press the button on the front of the PDP Monitor (or the ON ( ) button on the remote control) to switch the PDP Monitor on. To switch your PDP Monitor off, press the the OFF ( ) button on the remote control). button again (or

Choosing Your Language

When you start using your PDP Monitor for the first time, you must select the language which will be used for displaying menus and indications.

TV Time Language

Setup : English
Press the MENU ( ) button. The main menu is displayed. Result: Press the or button to select Setup. The Setup menu is displayed. Result:

Return

Press the ENTER (

) button.

TV Time Language PC Setup English : English Franais Deutsch Italiano Espaol Portugus
Press the or button to select Language. Press the ENTER ( ) button. The available languages are listed. Result: Select the appropriate language by pressing the or button. Press the ENTER ( ) button.

English - 15

3:59 PM

Page 16

Changing the Picture Standard
You can select the type of picture which best corresponds to your viewing requirements.
: Normal : Off : 16:9 Enter Return
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move

Picture : Dynamic

Press the MENU ( ) button. The main menu is displayed. Result: Press the or button to select Picture. The Picture menu is displayed. Result: Press the ENTER ( ) button. The Mode is selected. Result: Press the ENTER ( ) button again. The available options are listed. Result: Select the required option by pressing the or button. The following options are available. Result: Dynamic - Standard - Movie - Custom Entertain - Internet - Text - Custom : PC or DVI Mode.
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter
Picture : Dynamic Dynamic Standard : Normal Movie Custom : Off : 16:9

You can also set these options simply by pressing the P.MODE (Picture Mode) button on the remote control.

English - 16

Page 17
Customizing the Picture Settings
Your PDP Monitor has several setting options that allow you to control the picture quality.
Picture : Dynamic : Normal : Off : 16:9 Return
Press the MENU ( ) button. The main menu is displayed. Result: Press the or button to select Picture. The Picture menu is displayed. Result: Press the ENTER ( ) button. The Mode is selected. Result: Press the or button to select Custom. Press the ENTER ( ) button. Select the required option by pressing the or button. The following options are available. Result: Contrast - Brightness - Sharpness - Color Tint (NTSC only) Contrast - Brightness : PC or DVI Mode.
Custom Contrast Brightness Sharpness Color Tint G 55 R 50
Press the ENTER ( Result:

Contrast 100

The horizontal bar is displayed. Press the or button until you reach the optimal setting.
Press the or button to select other option(s). When the picture mode is set to Custom, the settings values may vary depending on the input source. (ex. AV, Component, PC, or DVI.)
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter Return : Off : 16:9 : Normal Picture : Dynamic
Press the MENU ( ) button to return to the Picture menu. Press the or button to select Color Tone. Press the ENTER ( ) button. Select the required option by pressing the or button. Result: The following options are available.
Picture Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter : Normal Cool2 Cool1 : OffNormal : 16:9 Warm1 Warm2 Return : Dynamic
Cool2 - Cool1 - Normal - Warm1 - Warm2 Custom - Cool - Normal - Warm : PC Mode. Cool - Normal - Warm : DVI Mode.

English - 17

Page 18
Adjusting the RGB Color (PC Mode)
TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter Return : Off : 16:9 : Custom Picture : Entertain
Preset to the PC mode by pressing the SOURCE (

Press the MENU ( Result:

The main menu is displayed.
Press the or button to select Picture. Result: The Picture menu is displayed. ) button.
Press the or button to select Color Tone. Press the ENTER ( ) button. Press the or button to select Custom. Press the ENTER ( ) button.

TV Zoom Position Reset

Zoom :Move Enter Return
Press the or button to select Position. Press the ENTER ( ) button. Adjust the position by pressing the , , , or button. Press the MENU ( Result: ) button.

Zoom :1

The Zoom menu is displayed again.
To return the factory defaults, select Reset by pressing the or button. Press the ENTER ( ) button. Result: The previously adjusted settings will be reset to the factory defaults.
Zoom Zoom Position Reset :1

English - 21

Page 22
Viewing the PC Information
TV Time Language PC : English Setup
You can view the current resolution and frequency of your pc.
Press the or button to select Information. Press the ENTER ( Result: ) button.
The resolution, vertical frequency and horizontal frequency are displayed. ) button.
TV Resolution H-Frequency V-Frequency Information 1024*768 48.3 KHz 59 Hz

Press the MENU (

English - 22

Page 23

Selecting the Picture Size
You can select the picture size which best corresponds to your viewing requirements.

TV Mode

Picture : Dynamic : Normal : Off : 16:9 Enter Return Custom Color Tone Color Control Film Mode Size PIP
Press the or button to select Size. Press the ENTER ( ) button. Select the required option by pressing the or button. Result: The following options are available. 16:9 : Sets the picture to 16:9 wide mode. Panorama : Use this mode for the wide aspect ratio of a panoramic picture. Zoom1 : The screen size when wide screen is vertically enlarged. Zoom2 : The screen size when the Zoom1 screen is vertically enlarged. 14:9 : Magnify the size of the picture more than 4:3. 4:3 : Sets the picture to 4:3 normal mode.
Size 16:9 Panorama Zoom1 Zoom2 14:9 4:3

PC to DVI Mode

TV 16:9 Panorama Zoom1 Zoom2 14:9 4:3 Size
You can select these options simply by pressing the P.SIZE button on the remote control. If you change the picture size In PIP mode, PIP disappears automatically. Depending on the input source, the P.SIZE options may vary. Check if the Video Wall (refer to page 33) is On if the Picture size is not function. Picture size does not function when the Video Wall is set to On. Change the setting to Off and try it again.
P Positioning and Sizing the screen using Zoom
Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction using the or button as well as the screen size. Move the screen up/down using the or button after selecting the by pressing the or button. Screen enlargement operates only in AV/S-Video/Component input modes. In PC or DVI mode, you can select either 16:9 or 4:3.

English - 23

Page 24
Freezing the Current Picture
You can freeze the picture when watching a moving picture simply by pressing the STILL button. To return to normal viewing, press it again.
The Still function in PIP mode will be applied to the main picture and not to the sub picture.
Changing the Sound Standard
You can select the type of special sound effect to be used when watching a given broadcast.

Sound : Standard

Pseudo Stereo : Off
Press the or button to select Sound. Result: The Sound menu is displayed. ) button.
TV Mode Sound : Standard Standard Movie Speech Pseudo Stereo : Off Music

The Mode is selected.

Press the ENTER ( ) button again. Select the required option by pressing the or button. Result: The following options are available. Standard - Music - Movie - Speech
You can select these options by simply pressing the S.MODE (Sound Mode) button on the remote control.

English - 24

Page 25

Extra Sound Settings

Pseudo Stereo Pseudo Stereo feature converts a monaural sound signal into two identical left and right channels. Once the Pseudo Stereo is set to On or Off, these settings apply to the sound effects such as Standard, Music, Movie, and Speech.
TV Mode Sound : Standard Pseudo Stereo : Off
Sound Mode : Standard Pseudo Stereo : Off Off
Press the or button to select Pseudo Stereo. Press the ENTER ( ) button. Select Off or On by pressing the or button. Press the ENTER ( ) button.

English - 25

Page 26
Activating Panel Button Lock
This feature allows you to lock the PDP Monitor panel buttons so that it cannot be operated via the PDP Monitor panel. It can, however, still be operated via the remote control. Only remote control can release the panel lock setting, so keep the remote control away from unauthorized users.
Function Screen Burn Protection Safety Lock Multi Control Video Wall Fan : Off
TV Key Lock IR Lock Change PIN Safety Lock : Off
Press the or button to select Function. Result: The Function menu is displayed. ) button.
Press the or button to select Safety Lock. Press the ENTER ( ) button. Press the ENTER ( ) button again to select Key Lock.
Select Off or On by pressing the or button. Press the ENTER ( ) button.
TV Key Lock IR Lock Change PIN

Safety Lock : Off Off On

English - 26

Page 27

Activating Remote Control Button Lock
This feature allows you to lock the remote control so that it cannot be operated via the remote control. It can, however, still be operated via the PDP Monitor Panel buttons.
TV Key Lock IR Lock Change PIN Move Enter Return

Safety Lock : Off

Press the or button to select Safety Lock. Press the ENTER ( ) button. Press the or button to select IR Lock. Press the ENTER ( ) button.
When IR Lock is set to On, you will not be able to use the remote control even if the remote control button is pressed. To cancel the Remote Control Button Lock, press 0000 using the numeric buttons on the remote control.

IR Lock : On

English - 27

Page 28

Setting Up Your Personal ID Number
This feature sets viewing restrictions and prevents unauthorized access to your PDP Monitor through the PIN (Personal Identification Number), which is a 4 digit number.
Press the or button to select Safety Lock. Press the ENTER ( ) button. Press the or button to select Change PIN. Press the ENTER ( ) button. Press the number buttons to enter your current 4-digit pin number.
The default pin number for a new PDP Monitor set is 0000.

Change PIN

Press the numeric buttons to enter your new 4-digit pin number. Re-enter your new pin number to confirm.

Enter PIN Enter New PIN

If you forget the pin number, press the remote control buttons in the following sequence, which resets the pin to 0-0-0-0: POWER (Off), MUTE, 8, 2, 4, POWER (On).
Enter PIN * * * Enter New PIN *

English - 28

4:00 PM

Page 29

Setting the MDC (Multiple Display Control)
This function enables you to easily control the connected monitors on the PC by specifying IDs to connected monitors.
TV Function Screen Burn Protection : Off
Safety Lock Multi Control Video Wall Fan
Press the or button to select Function. Result: The Function menu is displayed.
TV ID Setup Multi Control : : 00 -
Press the or button to select Multi Control. Press the ENTER ( Result: ) button.

ID Input

The Multi Control menu is displayed with the ID Setup selected.
Press the ENTER ( ) button again. Select the ID setup number by pressing the , , or numeric buttons. Press the ENTER ( ) button. Press the or button to select ID Input. Press the ENTER ( ) button. Enter ID input number by using the numeric buttons. Press the ENTER ( ) button.
Multi Control ID Setup ID Input : : 00
To operate the multi control function, PDP1 and PDP2 should be set in the ID Setup mode. When entering the ID Input number of PDP1 while the PDP Monitor is set in the ID Input mode, only PDP1 is switched to the Menu screen and you can operate the remote control. At this time, PDP2 doesn't operate with the remote control and displays the standby mode of ID Input. For further details, refer to the MDC program guide.

TV ID Setup ID Input

Multi Control : : 00 --

Enter ID Input Number

English - 29

Page 30

Preventing Screen Burn-in
To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes.
Screen Burn Protection Pixel Shift Signal Pattern All White Timer
Press the or button to select Screen Burn Protection. Press the ENTER ( ) button. Result: The Screen Burn Protection menu is displayed with the Pixel Shift selected. ) button again.
The Pixel Shift menu is selected.
TV Pixel Shift Vertical Line Time
Pixel Shift : Off Off On :4 : 4 min

Horizontal Dot : 4

Press the ENTER ( ) button. Select On by pressing the or button for making the screen move per regular hour and preventing the residual image. Press the ENTER ( ) button.
Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to prevent after image on the screen.
TV Pixel Shift Vertical Line Time Pixel Shift : On :4 : 4 min
Select the required option (Horizontal Dot, Vertical Line, or Time) by pressing the or button. Press the ENTER ( ) button. Press the or button until you reach the optimal setting. Press the ENTER ( ) button.
Optimum condition for pixel shift; PPM42M5S PPM42M5H PPM50/63M5H 4 min 4 min 4 min
Horizontal Dot Vertical Line Time

English - 30

Page 31
Reducing the Effects of Screen Burn
If screen burn has occurred, you can select a white screen or signal pattern (rolling screen) to help remove screen burn artifacts.
Press the or button to select Screen Burn Protection. Press the ENTER ( ) button. Result: The Screen Burn Protection menu is displayed with the Pixel Shift selected.
Press the or button to select the option (Signal Pattern or All White). Press the ENTER ( ) button.
Signal Pattern: This function removes after images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time. All White: This function removes after images on the screen by changing the color of pixels to white. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time. ) button.

To remove after images on the screen, use either All White or Signal Pattern function. Although both of the two functions remove after images on the screen, Signal Pattern is more effective. The after image removal function has to be executed for a long time (approximately 1 hour) to effectively remove after images on the screen. If after image is not removed after the execution of the function, repeat the function additionally.

English - 31

Page 32
Setting the Screen Burn Protection Timer
You can set the timer for Screen Burn Protection (hours, minutes). If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish.
TV Timer Mode Period Time
Timer : Off Off : Signal Pattern On : : 01 Hour 05 min
Press the or button to select Screen burn Protection. Press the ENTER ( ) button. Press the or button to select Timer. Press the ENTER ( ) button. Result: The Timer menu is displayed. ) button again.
TV Timer Mode Period Time Timer : On : Signal Pattern Signal Pattern : : 01 Hr. All White 05 min
Select On by pressing the or button. Press the ENTER ( ) button. Select the required option by pressing the or button. Result: Mode Period Time The following options are available. : Signal pattern, All White : Hour(1~24) : Minute(1~30)
Timer : On : Signal Pattern : : 01 Hr. Min.
Timer : On : Signal Pattern : : 01 Hour

05 Min. 05

English - 32

Page 33

Setting the Multiple Screen
You can get various display effects with many PDPs.
TV Function Screen Burn Protection Safety Lock Multi Control Video Wall Fan : Off
Press the or button to select Video Wall. Press the ENTER ( Result: ) button.
Video Wall Video Wall Format Screen Divider : Off : Full
The Video Wall menu is displayed with the Video Wall selected.
Press the ENTER ( ) button. Select On by pressing the or button. Press the ENTER ( ) button. Press the or button to select Format. Press the ENTER ( ) button. Select the required option by pressing the or button. Result: The following options are available.

If your PDP Monitor is displayed vertically, the fan automatically works. The message Check Fan is displayed if there is a fan problem. Please use the fan when the temperature is over 35 degrees. The Fan function for the models PPM-42M5SS, PPM42M5SS, PPM-42M5SB and PPM42M5SB is not available.

English - 37

Page 38

Setting the Film Mode

When a video input source is from a film such as movies, this feature identifies the source and changes to the corresponding screen.

Y de de

TV Mode Custom Color Tone Color Control Film Mode Size PIP Move Enter Return : Off Off : 16:9 On : Normal Picture : Dynamic
Press the or button to select Film Mode. Press the ENTER ( ) button. Select Off or On by pressing the or button. Press the ENTER ( ) button.
Automatically senses and processes film signals from all sources and adjusts the picture for optimum quality. Available in AV, S-Video, and Component (480i) modes. Unavailable in PC1, PC2, DVI mode.

English - 38

Page 39
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture of external A/V devices. In this way you can monitor the video input from any connected devices while monitoring other video inputs.
PIP PIP Source Swap Size Position : : : Off Off : PC1 On
Press the or button to select PIP. Press the ENTER ( ) button. Result: The PIP is selected.
Press the ENTER ( ) button again. To activate, set PIP to On by pressing the or button. Press the ENTER ( ) button. Press the or button to select Source. Press the ENTER ( ) button. Result: The following options are available. AV - S-Video - Component - PC1 - PC2 - DVI

Sound Select : Main

TV PIP
PIP : Off AV Source : PC1 S-Video Swap Component Size : PC1 Position : PC2 DVI Sound Select : Main
Select a source of the sub picture by pressing the or button. Press the ENTER ( ) button. Press the or button to select Swap. Press the ENTER ( ) button. Result: The main picture and sub picture are interchanged.
PIP PIP Source Swap Size Position : : : On : PC1
Press the or button to select Size. Press the ENTER ( ) button. Result: The following options are available. (Large) - (Small) - (Double Window) - (Double Wide)
Select a size of the sub picture by pressing the or button. Press the ENTER ( ) button.
PIP PIP Source Swap Size Position : : : On : PC1

English - 39

Page 40
Viewing the Picture in Picture (PIP) (continued)
TV PIP Source Swap Size Position : :

PIP : On : PC1

Press the or button to select Position. Press the ENTER ( ) button. Result: The following options are available. -

Normal picture but no sound
No picture or black and white picture Sound and picture interference Remote control malfunctions
Screen is black and power indicator light blinks steadily.

English - 50

Page 51

Technical Specifications

Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. (Class A product only)
Dimensions (W x D x H) Weight (Without stand) Screen aspect ratio Screen size
PPM42M5S/PPM42M5H - 1027 x 79 x 630.5 mm ; 40.43 x 3.11 x 24.82 inches PPM50M5H - 1204.6 x 79 x 724 mm ; 47.43 x 3.11 x 28.5 inches PPM63M5H - 1503.4 x 89 x 893.8 mm ; 59.19 x 3.5 x 35.19 inches PPM42M5S/PPM42M5H - 31kg PPM50M5H - 43kg PPM63M5H - 69kg 16:9 PPM42M5S/PPM42M5H - 42 inch PPM50M5H - 50 inch PPM63M5H - 63 inch PPM42M5S - 852 x 480 PPM42M5H - 1024 x 768 PPM50M5H/PPM63M5H - 1366 x 768 PAL, SECAM, NTSC (NT3.58/NT4.43) Stereo, Virtual Dolby 10W + 10W (8) U.S.A/Canada - AC120V~, 60Hz Other countries - AC100-250V~, 50/60Hz PPM42M5S - 330 Watts PPM42M5H - 380 Watts PPM50M5H - 490 Watts PPM63M5H - 630 Watts VIDEO IN - AV/S-VIDEO COMPONENT IN - Y/PB/PR (RCA, 3P, 480i~1080i) RGB1(PC1) IN - D-SUB, 15P RGB2(PC2) IN VGA~XGA (R/G/B/H/V) DVI IN - DVI-D type VIDEO OUT - VIDEO/L/R (RCA, 3P) VIDEO IN - L/R COMPONENT IN - L/R (RCA, 2P) AUDIO (Stereo jack for RGB1/2(PC1/2) and DVI input, 2 x mini jack) EXT SPEAKER (8) - R+/-, L+/RS232C - IN/OUT (D-SUB, 9P)
Native pixel resolution (H x V) Color systems Sound Audio output power Power supply Power consumption

Video inputs

Monitor outputs Audio inputs
Audio outputs External control

English - 51

Page 52

Dimension

English - 52

Page 53

Dimension (continued)

English - 53

Page 54

English - 54

Page 55

English - 55

Page 56

- AFTER SALES SERVICE

- Do not hesitate to contact your retailer or service agent if a change in the performance of your product indicates that a faulty condition may be present.

ELECTRONICS

BN68-00848A-00