CATEYE STRADA WIRELESS

CYCLOCOMPUTER CC-RD300W
Before using the computer, please thoroughly read this manual and keep it for future reference.
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending Copyright 2008 CATEYE Co., Ltd. CCRD3W-5
How to install the unit on your bicycle
1 Bracket band 2 Bracket 3 Nut 4 Speed sensor 5 Magnet 6 Sensor rubber pad 7 Bracket rubber pad 8 Nylon ties (x2)

WARNING / CAUTION

Do not concentrate on the computer while riding. Ride safely! Install the magnet, sensor, and bracket securely. Check these periodically. If a child swallows a battery, consult a doctor immediately. Do not leave the computer in direct sunlight for unnecessary or extended periods. Do not disassemble the computer. Do not drop the computer. Doing so may result in a computer malfunction or damage. When using the computer installed on the bracket, change the MODE by pressing on the three dots below the screen. Pressing hard on other areas can result in malfunction or damage to the computer. Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket threads. When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol. Dispose of used batteries according to local regulations. LCD screen may be distorted when viewed through polarized sunglass lenses.
Install the sensor and magnet
The distance between the computer and the sensor must not exceed the transmission range of 70 cm. The back of the computer must face the sensor.
The magnet must pass through the sensor zone.

Sensor zone

SEN SO ZON R E

Wireless Sensor

The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of interference. When adjusting the wireless sensor, note the following: Signals cannot be received if the distance between the sensor and the computer is too great. The transmission distance may be shorter due to low temperature or low battery. Signals can be received only when the back of the computer is facing the sensor. Interference may occur, resulting in incorrect data, if the computer is: Near a TV, PC, radio, motor, or in a car or train. Close to a railroad crossing, railway tracks, TV stations and/or radar base. Using with other wireless devices in close proximity.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2)this device must accept any interference received,including interference that may cause undesired operation. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by CatEye Co.,Ltd.May void the user s authority to operate the equipment.
Inside of right front fork

Max 70 cm

The clearance between the sensor surface 5 and the magnet must not exceed 5 mm.

SE NS ZO OR NE

Tire circumference reference table

Tire size

12 x 1.x 1.x 1.x 1.x 1.x 1.x 1.x 1.x 1-3/x 1-3/x 1-1/x x 3/4 Tubular 24 x 1-1/x 1-1/x 1.x 2.x 2.x 7/x 1(59) 26 x 1(65) 26 x 1.x 1-1/x 1-3/x 1-1/x 1.x 1.x 1.x 1.x 2.x 2.x 2.x 2.x 3.x x 1-1/x 1-1/x 1-3/x 20C 650 x 23C 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 40C 29 x 2.x 2.3

L (mm)

Preparing the computer
Battery case cover When the computer is

mm 5 mm

mounted on the bracket

MENU AC MODE

: Speed unit : Wheel size icon : Sensor signal reception icon Push!

1 Install the sensor

SEN SO ZONR E
Inside of right front fork Pull securely

2 Install the magnet

SEN S ZO OR NE
all data (initialization) 1 Clearthe AC button on the back. Press
* Install the sensor as close to the upper part of the front fork as possible.

Toward the sensor zone

3 Attach the bracket to the stem or handlebar
When attaching the bracket to the stem
2 Select the desired speed units Select or .

km/h mph Register the setting
3 Enter the tire circumference of your bicycle in mm.
Enter the tire circumference
* Refer to the tire circumference reference table.
Increase Move digits (by pressing & holding) Register the setting
Caution: Make sure that the back of the computer faces the sensor. * The computer may not function appropriately on some stem if its back does not face the sensor as shown in A. When attaching the bracket to the handlebar

Handlebar

Caution: Round off the cut edge of the bracket band to prevent injury.
4 Set the clock pressed and held, Displayed When MODE is
time, Hour, and Minute will appear, in this order.
24h 12h, or increase the value Switch the screen or move digits MODE (by pressing MENU & holding)
Measure wheel circumference (L) of your bike To get the most accurate calibration do a wheel roll out. With the valve stem perpendicular to the ground, mark the pavement at the valve stem. With the riders weight on the bike, roll the wheel one tire revolution in a straight line and mark the ground when the valve stem is perpendicular to the ground again. Measure the distance in millimeters. This is the most accurate wheel calibration number.

4 Remove/install the

computer
While supporting it by hand,
* For wing type handlebar or oversized stem, bracket can be mounted using the Bracket Holder and nylon ties. (Option) 2
push it out as if lifting the front up
* After installation, rotate the front wheel gently to check that the speed is displayed on the computer. If the speed is not displayed, check that conditions A , B , and C , above, have been done appropriately.

CC-RD300W

Operating the computer [Measuring screen] Troubleshooting
MODE does not work when the computer is mounted on its bracket. Check that there is no dirt between the bracket and the computer. Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly. The sensor signal reception icon does not flash. (The speed is not displayed.) (Spin the front wheel, bringing the computer closer to the sensor. If the icon now flashes, this indicates that the computer and sensor are too far apart or that the battery is low.) Is the clearance between the sensor and magnet too great? (must be 5 mm) Does the magnet pass through the sensor zone? Adjust the positions of the magnet and sensor. Is the computer installed at the correct angle? Back of computer must face toward the sensor. Are the computer and sensor too far apart? (The distance must not exceed 70 cm.) Install the sensor closer to the computer. Is the computer or sensor battery weak? In winter, battery performance diminishes. Replace the battery. In the case of the computer, after replacing the battery, re-start the computer according to the Preparing the computer, above. No display. Is battery in the computer run down? Replace it. Then reinitialize the computer referring to Preparing the computer. Incorrect data appear. Reinitialize the computer referring to Preparing the computer.

Tm Elapsed Time

0:0000 - 9:5959

Pace arrow

Indicates whether the current speed is faster ( ) or slower ( ) than the average speed.

Dst Trip Distance

0.00 - 999.99 km [mile]

Current speed

0.0(4.0) - 105.9 km [0.0(3.0) - 65.9 mph]

Dst 2 Trip Distance-2

0.00 - 999.99 / 1000.0 - 9999.9 km [mile]

Selected Mode

Starting/Stopping measurement
Measurements occur automatically when the bicycle is in use. During measurement, or flashes.

Av Average Speed*2

0.0 - 105.9 km/h [0.0 - 65.9 mph]
Switching computer function
Pressing MODE switches function, in order, as shown on the left.

Mx Maximum Speed

0.0(4.0) - 105.9 km/h [0.0(3.0) - 65.9 mph]

Resetting data

To reset measurement data, display any data other than for Dst-2 and then press and hold MODE. Pressing and holding MODE with Dst-2 displayed resets Dst-2 only. The total distance is never reset.

Odo Total Distance

0.0 - 9999.9 / 10000 - 99999 km [mile]

Specification

Battery.. Computer : Lithium battery (CR2032) x 1 Sensor : Lithium battery (CR2032) x 1 Battery life. Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary depending on the conditions of use.) Sensor : Unit Total Distance reaches about 10,000 km (6,250 mile) * This is the average figure of being used under 20 C temperature and the distance between the computer and the sensor is 65 cm. Controller.. 4-bite, 1-chip microcomputer (Crystal controlled oscillator) Display.. Liquid crystal display Sensor.. No contact magnetic sensor Wheel circumference range.. 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm) Working temperature.. 32 F - 104 F (0 C - 40 C) (This product will not display appropriately when exceeding the Working Temperature range. Slow response or black LCD at lower or higher temperature may happen respectively.) Dimensions/weight. 1-53/64 x 1-7/32 x 5/8 (46.5 x 31 x 16 mm) / 0.78 oz (22 g) * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice.
0:00 - 23:59 or 1:00 - 12:59
*1 With the computer installed on the bracket, press on the three raised dots on the face of the computer. *2 If Tm exceeds approximately 27 hours or DST exceeds 999.99 km,.E (Error) is displayed as the average speed. Reset data.

Power-saving function

If the computer has not received a signal for 10 minutes, power-saving mode will activate and only the clock will be displayed. When the computer receives a sensor signal again, the measuring screen reappears. If two weeks inactivity elapses, power-saving mode will change to SLEEP mode. Pressing the MODE in SLEEP mode brings up the measuring screen.

Changing the computer settings [menu screen]
If the MENU is pressed with the measuring screen displayed, the menu screen appears. Press the MODE when measurement has stopped and no signal is MENU being received to change menu settings.

Standard parts

#169-9691

Wheel magnet

#166-5150

Lithium battery (CR2032)

Optional parts

#160-2190

Parts kit

#160-2770

Bracket holder

#160-2196

Speed sensor

#160-0280

Bracket band

#160-2193

Bracket

Wheel selection

Wheel size entry

Clock setting

Total distance manual entry

Speed unit

LIMITED WARRANTY
2-Year Computer only (Accessories/Bracket sensor and Battery Consumption excluded) CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to CatEye shall be borne by person desiring service. For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.
CO.,LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section Service & Research Address for USA CatEye North America 2300 Central Ave Suite L Boulder, CO 80301 Phone: 303.443.4595 Toll Free: 800.5CATEYE Fax: 303.473.0006 E-mail: service@cateye.com URL: http://www.cateye.com
Setting * After changing, be sure to press MENU to register the change (by setting. pressing & * If the menu screen is not touched for a minute, the MODE holding) Measuring screen reappears without data changes.

Wheel selection.. Toggle between the specified wheel size (tire circumference) and. Use this function if the computer is to be shared between two bicycles.. Pressing MODE toggles between and. Wheel size entry. Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. , display using Wheel selection. * To enter the wheel size Clock setting.. To set the clock, refer to Preparing the computer-4. Total distance manual entry.. Before reinitializing the computer, note the total distance. This reading will later allow you to enter the total distance manually. Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. and. Speed unit. Pressing MODE toggles between

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.

Replacing the battery

Push! Computer If the display appears faded, replace the battery. Install a new lithium battery (CR2032) with the (+) side facing upward. Then reinitialize the computer referring to Preparing the computer. * When the battery is installed, place the inner seal cap with the TOP side upward. Sensor If sensor reception is poor, replace the battery. After replacement, check the positions of the sensor and magnet.

Inner Seal Cap CR2032

CR2032

CATEYE STRADA WIRELESS

CYCLOCOMPUTER CC-RD300W
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending Copyright 2008 CATEYE Co., Ltd. CCRD3W-5

SEN SO ZON R E

SE NS ZO OR NE

5 mm 5 mm

MENU AC MODE

km/h mph

4 MODE

24h 12h

12 x 1.x 1.x 1.x 1.x 1.x 1.x 1.x 1.x 1-3/x 1-3/x 1-1/x x 3/4 Tubular 24 x 1-1/x 1-1/x 1.x 2.x 2.x 7/x 1(59) 26 x 1(65) 26 x 1.x 1-1/x 1-3/x 1-1/x 1.x 1.x 1.x 1.x 2.x 2.x 2.x 2.x 3.x x 1-1/x 1-1/x 1-3/x 20C 650 x 23C 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 40C 29 x 2.x 2.3

SEN SO ZONR E

SEN S ZO OR NE

CC-RD300W

0:0000 - 9:5959

0.00 - 999.99 km [mile]

0.0(4.0) - 105.9 km [0.0(3.0) - 65.9 mph]
0.00 - 999.99 / 1000.0 - 9999.9 km [mile]
0.0 - 105.9 km/h [0.0 - 65.9 mph]
0.0(4.0) - 105.9 km/h [0.0(3.0) - 65.9 mph]
0.0 - 9999.9 / 10000 - 99999 km [mile] MODE 0:00 - 23:59 1:00 - 12:59

Dst-2 MODE Dst-2 Dst-2

SLEEP MODE

#169-9691

#166-5150

#160-2770

MENU MODE
#160-2190 #160-2196 #160-0280 #160-2193

MODE MODE