An uninterruptible power supply (UPS) supplies battery power to your computer during a power failure. Although you cannot run your computer for an extended period of time with a UPS, a UPS lets you run your computer long enough to save your work and shut down your computer normally. For more information, see Setting up an uninterruptible power supply on page 132.

Starting your computer

To start your computer:
Connect the cables to your computer using the setup poster. Turn on your computer. If you are starting your computer for the first time, follow the on-screen instructions to set up your computer. Turn on any peripheral devices, such as printers or scanners, and see the documentation that came with the device for setup instructions.
Turning off your computer
Tips & Tricks When you turn off your computer, certain components in the power supply and system board remain energized. In order to remove all electrical power from your computer, unplug the power cord and modem cable from the wall outlets. We recommend disconnecting the power cord and modem cable when your computer will not be used for long periods.
To turn off your computer:
Click Start, then click Turn Off Computer. The Turn Off Computer dialog box opens. Click Turn Off. Windows shuts down and turns off your computer.
Important If for some reason you cannot use the Turn Off Computer option in Windows to turn off your computer, press and hold the power button for about five seconds, then release it.
Restarting (rebooting) your computer
If your computer does not respond to keyboard or mouse input, you may have to close programs that are not responding. If closing unresponsive programs does not restore your computer to normal operation, you may have to restart (reboot) your computer.
To close unresponsive programs and restart your computer:
Press CTRL+ALT+DEL, then click Task Manager. The Task Manager window opens. Click the Applications tab, then click the program that is not responding. Click End Task. If your computer does not respond, turn it off, wait ten seconds and turn it on again.
Important If your computer does not turn off, press and hold the power button for about five seconds, then release it.

Keyboard

Function keys Navigation keys Indicators

Windows keys

Application key

Directional keys

Numeric keypad

Press these keys.

Function keys
Start program actions. Each program uses different function keys for different purposes. See the program documentation to find out more about the function key actions. Press these keys to move the cursor to the beginning of a line, to the end of a line, up the page, down the page, to the beginning of a document, or to the end of a document. Show if your NUM LOCK, CAPS LOCK, or SCROLL LOCK keys are activated. Press the corresponding key to activate the function. Press one of these keys to open the Windows Start menu. These keys can also be used in combination with other keys to open utilities like F (Search utility), R (Run utility), and E (Explorer utility). Access shortcut menus and help assistants in Windows. Move the cursor up, down, right, or left. Use these keys to type numbers when the numeric keypad (NUM LOCK) is turned on.

Using the Start menu

You can start programs, open files, customize your system, get help, search for files and folders, and more using the Start menu.

To use the Start menu:

Click the Start button on the lower left of the Windows desktop. The Start menu opens showing you the first level of menu items. Click All Programs to see all programs and files in the Start menu. When you move the mouse pointer over any menu item that has an arrow next to it, another menu, called a submenu, opens and reveals related files, programs, or commands. Click a file or program to open it.
For more information about the Windows XP Start menu, click Start, then click Help and Support. Type the keyword Windows Start menu in the Search box , then click the arrow.
Adding icons to the desktop
You may want to add an icon (shortcut) to the desktop for a program that you use frequently.
To add icons to the desktop:
Click Start, then click All Programs. Right-click (press the right mouse button) the program that you want to add to the desktop. Click Send To, then click Desktop (create shortcut). A shortcut icon for that program appears on the desktop.
For more information about desktop icons in Windows XP, click Start, then click Help and Support. Type the keyword desktop icons in the Search box , then click the arrow.

Identifying window items

When you double-click the icon for a drive, folder, file, or program, a window opens on the desktop. This example shows the Local Disk (C:) window, which opens after you double-click the Local Disk (C:) icon in the My Computer window.
Title bar Menu bar Close Maximize Minimize
Identifying window items Every program window looks a little different because each has its own menus, icons, and controls. Most windows include these items: Window item Description
The title bar is the horizontal bar at the top of a window that shows the window title. Clicking the minimize button reduces the active window to a button on the taskbar. Clicking the program button in the taskbar opens the window again. Clicking the maximize button expands the active window to fit the entire computer display. Clicking the maximize button again restores the window to its former size. Clicking the close button closes the active window or program. Clicking an item on the menu bar starts an action such as Print or Save.
For more information about windows in Windows XP, click Start, then click Help and Support. Type the keyword window in the Search box , then click the arrow.

If you type all of the name, Search will list all files and folders of that name. If you type part of the name, Search will list all of the file and folder names containing the letters you typed.
Click Search. When the search is completed, Windows lists the files and folders whose names contain the text that you searched for.
Open a file, folder, or program by double-clicking the name in the list.
For more information about searching for files and folders in Windows XP, click Start, then click Help and Support. Type the keyword searching in the Search box , then click the arrow.
Using advanced search options
Search can find files meeting more criteria than file name. You can narrow your search by selecting the search options that you want. You can search by the:
Date the file was created or modified. Size of the file. Type of file, such as a program or a text document.

Working with documents

Computer documents include word processing files, spreadsheet files, or other similar files. The basic methods of creating, saving, opening, and printing a document apply to most of these types of files. The following examples show how to create, save, open, and print a document using Microsoft WordPad. Similar procedures apply to other programs such as WordPerfect, Microsoft Word, and Microsoft Excel. For more information about using a program, click Help on its menu bar.

Creating a new document

To create a new document:
Click Start, All Programs, Accessories, then click WordPad. Microsoft WordPad starts and a blank document opens.
Begin composing your document. Use the menus and toolbar buttons at the top of the window to format the document.

Saving a document

After you create a document, you need to save it if you want to use it later.

To save a document:

Click File, then click Save. The Save As dialog box opens.

Save in list

File name
Click the arrow button to open the Save in list, then click the folder where you want to save the file. If you do not see the folder you want, browse through the folders listed below the Save in list. Type a new file name in the File name box. Click Save.
For more information about saving documents in Windows XP, click Start, then click Help and Support. Type the keyword saving in the Search box , then click the arrow.

- OR On the current Web page, click a link to a Web site. The Web browser locates the server computer on the Internet, downloads (transfers) data to your computer, and displays the page on the site that you requested.
For more information about connecting to a Web site in Windows XP, click Start, then click Help and Support. Type the keyword connecting to Web site in the Search box , then click the arrow.
Sometimes Web pages display slowly. The speed that a Web page displays on the screen depends on the complexity of the Web page and other Internet conditions. Additionally, the speed of your connection will determine how fast Web pages display.

Downloading files

Downloading is the process of transferring files from a computer on the Internet to your computer. To protect your computer against viruses, make sure that you scan the files you download. For more information, see Protecting your computer from viruses on page 160.
To download files or programs from a Web site:
Connect to your Internet account. In the address bar, type the address of the Web site that contains the file or program you want to download, then click GO on the browser address bar. - OR Click a link on a Web page to navigate to the Web site containing the file that you want to download.
Create or locate the folder where you want to store the file on your computer. For more information, see Working with files and folders on page 36. Click the link on the Web page for the file that you want to download. Follow the on-screen instructions for saving the file in the folder that you want. A copy of the file is downloaded to your computer. The time that it takes to transfer the file to your computer depends on file size and Internet conditions. Open the folder that you created. Install or view the downloaded file by double-clicking it. If applicable, follow the instructions provided on the Web site to run or install the program.
For more information about downloading files in Windows XP, click Start, then click Help and Support. Type the keyword downloading files in the Search box , then click the arrow.

Using e-mail

E-mail (electronic mail) lets you send messages to anyone who has an Internet connection and e-mail address. E-mail is usually a free service of your Internet account. The Internet never closes, so you can send e-mail messages at any time. Your e-mail messages arrive at most e-mail addresses in minutes. An e-mail address consists of a user name, the @ symbol, and the Internet domain name of the Internet service provider (ISP) or company that hosts that user. Your e-mail address is assigned when you sign up for an account with an ISP. For example, a person with an account with America Online might have an e-mail address that is similar to this one:

For more information about adjusting display settings in Windows XP, click Start, then click Help and Support. Type the keyword changing display settings in the Search box , then click the arrow.
Adjusting the screen resolution
You can increase the screen resolution to fit more icons on your desktop, or you can decrease the resolution to make reading the display easier. The higher the resolution, the smaller individual components of the screen (such as icons and menu bars) appear.
To adjust the screen resolution:
Click Start, then click Control Panel. The Control Panel window opens. If your Control Panel is in Category View, click Appearance and Themes. Click/Double-click the Display icon. The Display Properties dialog box opens. Click the Settings tab.
Drag the Screen resolution slider to the size you prefer. Click OK, then click Yes.
For more information about adjusting screen resolution in Windows XP, click Start, then click Help and Support. Type the keyword changing screen resolution in the Search box , then click the arrow.
Changing the colors on your Windows desktop
You can change the colors of Windows desktop items, such as the background color and dialog box title bars.
To change desktop colors:
Click the Appearance tab.
Click the arrow button to open the Color scheme list, click the color scheme you want, then click OK. The new colors appear on your desktop. - OR If you want to create a new color scheme as part of a desktop theme:

a b c d e

Click Advanced. The Advanced Appearance dialog box opens. Click the arrow button to open the Item list, then click the item you want to change. Change the color or font settings for the item. Click OK, then click the Themes tab. Click Save As, type a name for the new theme, then click OK twice. The new colors appear on your desktop.
Changing the desktop background
You can change the Windows desktop background picture. Windows provides several backgrounds, or you can use pictures that you have created or retrieved from other sources.
To change the desktop background:
Click Start, then click Control Panel. The Control Panel window opens. If your Control Panel is in Category View, click Appearance and Themes. Click/Double-click the Display icon. The Display Properties dialog box opens. Click the Desktop tab.
Click a background picture in the Background list. - OR Click Browse to select a background picture from another location.
If you want the picture you chose to cover the entire screen, click the arrow button to open the Position list, then click Stretch or Tile.

Select 1. Delete all files (Automated Fdisk/Format). Select 1. Continue deleting all files and restart. When prompted, press any key to continue. Select 2. Boot from CD-ROM. Select a language option. Select 2. Automated installation of Windows XP. If an Advanced Menu option appears and your computer does not have a hard drive that requires a special hard drive driver, select 1. Normal installation of Windows (XP or 2000). This is the most commonly selected option. - OR If an Advanced Menu option appears and your computer does have a hard drive that requires a special hard drive driver, for example a Serial ATA drive, select 2. Installation of Windows w/ special HDD controllers.
When prompted, remove the red Drivers CD and insert the blue Operating System CD into the CD or DVD drive, then press any key to continue. When prompted, accept the License Agreement by pressing Y. Wait while the setup program copies files to your hard drive. When your computer restarts, do NOT press any key to boot from CD. Follow the on-screen instructions to set your Regional and Language Options. Click Personal / Home Use, then click Continue. The Gateway Driver and Application Recovery program starts and the Drivers and Application Recovery tab appears. When prompted, insert the red Drivers CD, then click OK. When prompted, insert the yellow Applications CD(s), then click Continue. The Gateway Application Loader automatically installs your drivers and programs. Your computer restarts several times during this process. Do not press any keys or buttons during this process unless prompted to do so.
When the Gateway Application Loader has finished, go to the Windows desktop by clicking Close. Install additional programs by following the instructions in To reinstall programs from the Applications CD(s): on page 180. Install other software, such as Microsoft Works Suite and gaming software, by following the instructions in To reinstall other programs from a CD: on page 181.

Upgrading Your Computer

This chapter provides information about upgrading and replacing components in your computer. Read this chapter to learn how to:
Open and close the computer case Remove and install drives and components Remove and install add-in cards Remove and install system boards Add memory Change the battery
You must open the computer case to upgrade or replace components. If you are not comfortable with these procedures, get help from a more experienced computer user or computer service technician.
Chapter 13: Upgrading Your Computer
When cleaning the case, do not use abrasive or solvent cleaners because they can damage the finish. Use soap and water or a dilution of water and isopropyl alcohol. For more information, see Cleaning your computer on page 171.

Internet

You cannot connect to the Internet using a dial-up modem
Make sure that your computer is connected to the telephone line and the telephone line has a dial tone. Use the setup poster to make sure that the connections have been made correctly. Make sure that no one else is using the telephone line. If you have the call waiting feature on your telephone line, make sure that it is disabled. Make sure that your account with your Internet service provider (ISP) is set up correctly. Contact your ISP technical support for help.
Make sure that you do not have a problem with your dial-up modem. For more information, see Modem (dial-up) on page 223.
Help and Support For more information about troubleshooting Internet connections in Windows XP, click Start, then click Help and Support. Type the keyword troubleshooting connections in the Search box , then click the arrow.
You see an Unable to locate host message and are unable to browse the Internet
This problem can occur when you have typed a URL (Web address) incorrectly, you have lost your Internet connection, or your ISP is having technical difficulties. Double-check the URL or try a different URL. If the error message still appears, disconnect from the ISP connection and close your browser, then reconnect and open the browser. If you still get the error, your ISP may be having technical difficulties.
Connecting to a Web site takes too long
Many factors can affect Internet performance:
The condition of the telephone lines in your residence or at your local telephone service The condition of the Internet computers to which you connect and the number of users accessing those computers The complexity of graphics and multimedia on Web pages Having multiple Web browsers open, performing multiple downloads, and having multiple programs open on your computer
People are sending you e-mail messages, but you have not received any mail
Click the receive button in your e-mail program. Make sure that your account with your Internet service provider (ISP) is set up correctly. Contact your ISP for technical support.
The keyboard does not work
Make sure that the keyboard cable is plugged in correctly. For more information, see the poster that came with your computer. Remove all extension cables and switch boxes. Clean the keyboard by using an aerosol can of air with a narrow, straw-like extension to remove dust and lint trapped under the keys. Try a keyboard that you know works to make sure that the keyboard port works. Reinstall the keyboard device driver. For more information, see Reinstalling device drivers on page 177.
A keyboard character keeps repeating or you see a keyboard stuck or key failure error message
Make sure that nothing is resting on the keyboard. Make sure that a key is not stuck. Press each key to loosen a key that might be stuck, then restart your computer.

Click Start, then click Control Panel. The Control Panel window opens. If your Control Panel is in Category View, click Printers and Other Hardware. Click/Double-click the Phone and Modem Options icon, then click the Dialing Rules tab. Click the location from which you are dialing, then click Edit. Make sure that all settings are correct.
For more information about dialing properties in Windows XP, click Start, then click Help and Support. Type the keyword dialing in the Search box , then click the arrow.
Disconnect any answering machine, fax machine, or printer that is on the same line as the modem. Do not connect these devices to the same telephone line as the modem. Make sure that you are not using a digital, rollover, or PBX line. These lines do not work with your modem. Check for line noise (scratchy, crackling, or popping sounds). Line noise is a common problem that can cause the modem to connect at a slower rate, abort downloads, or even disconnect. The faster the modem, the less line noise it can tolerate and still work correctly. Listen to the line using your telephone. Dial a single number (such as 1). When the dial tone stops, listen for line noise. Wiggle the modem cable to see if that makes a difference. Make sure that the connectors are free from corrosion and all screws in the wall or telephone jack are secure. You can also call your telephone service and have them check the telephone line for noise or low line levels.
Try another telephone line (either a different telephone number in your house or a telephone line at a different location). If you can connect on this line, call your telephone service. Try connecting with the modem at a lower connection speed. If reducing the connection speed lets you connect, call your telephone service. The telephone line may be too noisy.
You cannot connect to the Internet
Your ISP may be having technical difficulties. Contact your ISP technical support for help. See if the modem works with a different communications program. The problem may be with just one program.
Your 56K modem does not connect at 56K
Current FCC regulations restrict actual data transfer rates over public telephone lines to 53K. Other factors, such as line noise, telephone service provider equipment, or ISP limitations, may lower the speed even further.
Troubleshooting If your system has a v.90 modem, the speed at which you can upload (send) data is limited to 33.6K. If your system has a v.92 modem, the speed at which you can upload data is limited to 48K. Your ISP may not support 48K uploads. You can check modem connection speeds and dial-up network (DUN) connections by accessing the gateway.your.way dial-up server. The server also contains drivers, patches, and updates for current Gateway hardware and software. The server provides a secure connection and is a stand-alone server. You cannot use it to access the Internet. The server cannot be accessed Mondays from 8:00 a.m. to 12:00 p.m. CT.

Reinstall the device driver. For more information, see Reinstalling device drivers on page 177. Open your computer and reseat the modem. For more information, see Adding or replacing add-in cards on page 199.
The modem is noisy when it dials and connects
When your modem tries to connect to another modem, it begins handshaking. Handshaking is a digital getting acquainted conversation between the two modems that establishes connection speeds and communication protocols. You may hear unusual handshaking sounds when the modems first connect. If the handshaking sounds are too loud, you can turn down the modem volume.
To turn down the modem volume:
Click Start, then click Control Panel. The Control Panel window opens. If your Control Panel is in Category View, click Printers and Other Hardware. Click/Double-click the Phone and Modem Options icon, then click the Modems tab. Click the modem you want to adjust, then click Properties. Click the Modem tab, then adjust the Speaker volume control. Click OK twice to close the Phone and Modem Options dialog box.

Monitor

The screen resolution is not correct
Change the screen resolution from the Display Properties dialog box. For more information, see Adjusting the screen resolution on page 118.
Help and Support For more information about changing the screen resolution in Windows XP, click Start, then click Help and Support. Type the keyword screen resolution in the Search box , then click the arrow.
The computer is running but there is no picture
Make sure that the monitor is plugged in and turned on. If the monitor is turned on, the power LED should be lit. Adjust the brightness and contrast controls to the center position. Make sure that the monitor cable is connected to the video port on the back of your computer. Check the port and cable for bent or damaged pins. Reinstall the device driver. For more information, see Reinstalling device drivers on page 177. Open your computer case and reseat the video card. For more information, see Adding or replacing add-in cards on page 199. Connect a monitor that you know works to your computer.

The color is not uniform

Make sure that the monitor warms up for at least 30 minutes before making a final judgment about color uniformity. Make sure that:

Non-shielded speakers are not placed too close to the monitor. The monitor is not positioned too close to another monitor, electric fan, fluorescent light, metal shelf, or laser printer. You demagnetize the screen using the monitors degauss feature. For more information on degauss, see your monitors documentation.
Why is there a horizontal line or wire visible across the monitor screen?
Your monitor may use a thin damper wire, located approximately 1/3 of the way down from the upper screen edge and 1/3 of the way up from the lower screen edge, to stabilize the internal aperture grille. These wires are most obvious when the monitor displays a white background. The aperture grille allows more light to pass through the screen for brighter colors and greater luminescence. The damper wire is a critical part of the overall monitor design and does not negatively affect the monitor's function.
The text on the display is dim or difficult to read
Adjust the brightness and contrast controls. Use the monitor degauss feature (see your monitor documentation) or turn off your computer and monitor, leave them off for at least a half hour, then restart your computer. Change the display settings. For more information, see Adjusting the screen and desktop settings on page 116. Move the monitor away from sources of electrical interference, such as televisions, unshielded speakers, microwaves, fluorescent lights, and metal beams or shelves.
For more information about display types, see your monitor and video card documentation.

The mouse does not work

Make sure that the mouse cable is plugged in correctly. Shut down and restart your computer. Remove all extension cables and switch boxes. Try a mouse you know is working to make sure that the mouse port works. Reinstall the device driver. For more information, see Reinstalling device drivers on page 177.
The mouse works erratically
If the mouse pointer begins moving erratically across the computer display or becomes difficult to control precisely, cleaning the mouse will likely improve its accuracy. If you have an optical mouse, clean the mouse by wiping the bottom with a clean, damp cloth. Make sure that the optical sensor is clean and free or debris. If you have a trackball mouse, see Cleaning the mouse on page 173.

Care during use

Do not walk on the power cord or allow anything to rest on it. Do not spill anything on the system. The best way to avoid spills is to avoid eating and drinking near your system. Some products have a replaceable CMOS battery on the system board. There is a danger of explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or equivalent type recommended by the manufacturer. Dispose of batteries according to the manufacturers instructions. When the computer is turned off, a small amount of electrical current still flows through the computer. To avoid electrical shock, always unplug all power cables and modem cables from the wall outlets before cleaning the system. Unplug the system from the wall outlet and refer servicing to qualified personnel if:
The power cord or plug is damaged. Liquid has been spilled into the system. The system does not operate properly when the operating instructions are followed. The system was dropped or the cabinet is damaged. The system performance changes.
Replacement parts and accessories
Use only replacement parts and accessories recommended by Gateway.
Do not use Gateway products in areas classified as hazardous locations. Such areas include patient care areas of medical and dental facilities, oxygen-laden environments, or industrial facilities.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.
Regulatory compliance statements

United States of America

Federal Communications Commission (FCC) Unintentional emitter per FCC Part 15
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a different circuit from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.
Compliance Accessories: The accessories associated with this equipment are: shielded video cable when an external monitor is connected. These accessories are required to be used in order to ensure compliance with FCC rules.
FCC declaration of conformity
Responsible party: Gateway Companies, Inc. 610 Gateway Drive, North Sioux City, SD 57049 (605) 232-2000 Fax: (605) 232-2023 Product: Gateway 510 For unique identification of the product configuration, please submit the 10-digit serial number found on the product to the responsible party. This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution

Changes or modifications not expressly approved by Gateway could void the FCC compliance and negate your authority to operate the product.
Telecommunications per part 68 of the code of federal regulations (CFR 47) (applicable to products fitted with USA modems)
Your modem complies with Part 68 of the code of federal regulations (CFR 47) rules. On the computer or modem card is a label that contains the registration number and Ringer Equivalence Number (REN) for this device. If requested, this information must be provided to the telephone company. A telephone line cord with a modular plug is required for use with this device. The modem is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68-compliant. See installation instructions for details. The Ringer Equivalence Number (REN) is used to determine the number of devices which may be connected to the telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. If this device causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. The telephone company may request that you disconnect the equipment until the problem is resolved. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. This equipment cannot be used on telephone company-provided coin service. Connection to party line service is subject to state tariffs. Contact the state public utility commission or public service commission for information. When programming or making test calls to emergency numbers:

eject button CD drive 3, 83 DVD drive 3, 83 electrostatic discharge (ESD) 187 e-mail 55, 60 address 60 checking for messages 61 sending 60 transferring settings from old computer 154 ergonomics 12 Error-checking 165 eSupport using 26 Ethernet wired network 138, 139 wireless network 138, 142 Ethernet jack 6 external audio jack 5, 6
Fast Ethernet 139 faxes automatically canceling 73 canceling 71 configuring Fax 65 failed transmission 72 installing Fax 64 receiving and viewing 71 retrying 72 sending 67 sending from program 70 sending scanned image 70 setting up cover page template 69 troubleshooting 225 files backing up 169 copying 39, 51 cutting 39, 51 deleting 31, 41, 51, 164 downloading 59 finding 42, 44 moving 39 opening 20, 32 pasting 39, 51 recovering 41, 219 renaming 51 searching for 42, 44, 152 transferring 151 troubleshooting 219 types 152 viewing list 36 Files and Settings Transfer Wizard 150 finding files and folders 42, 44, 152 Help and Support topics 24 specifications 8 Firewire port 3, 21, 112 folders copying 39, 51 creating 37 cutting 39, 51 deleting 31, 41, 51
finding 42, 44 moving 39 opening 20, 36 pasting 39, 51 recovering 41 renaming 51 searching for 42, 44 viewing list 36 fragmentation 167 front bezel removing 193 replacing 193 function keys 18
game multi-player 137 Gateway model number 7 serial number 7 Technical Support 234 Web address 26 Web site 26 gateway dial-up server 225 gigabit Ethernet 139
hard drive backing up files 169 checking for errors 165 checking for free space 163 defragmenting 167 deleting files and folders 164 indicator 3 replacing 197 scanning for errors 165 troubleshooting 219 headphone jack 5 help online 25 using 24 Help and Support 24 searching 24
starting 24 Using your computer link 24 Hibernate mode 3, 127, 130 home office network 135 hot-swapping 21 hyperlinks 57
i.Link port 3, 21, 112 IEEE 1394 port 3, 21, 112 IEEE 802.11 creating a network 138 speed and frequency 142 using a network 142 indicators Caps Lock 18 CD drive 83 CD-RW drive 83 drive activity 83 DVD drive 83 DVD/CD-RW drive 83 DVD-RAM/-RW/CD-RW drive 83 hard drive 3 Num Lock 18 numeric keypad 18 Pad Lock 18 power 3 Scroll Lock 18 inkjet printer 9 installing add-in cards 199 battery 211 camera 111 cards 199 CD drive 194 CD-RW drive 194 devices 21 digital camera 21, 111 digital video camera 21 diskette drive 194 drivers 177 drives 194, 197 DVD drive 194
DVD/CD-RW drive 194 DVD-RAM/-RW/CD-RW drive 194 expansion cards 199 Fax 64 front bezel 191 hard drive 197 memory 207 Microsoft Fax 64 peripheral devices 21, 154 Pinnacle Expression 112 power supply 202 printer 21, 154 programs 156, 180 scanner 21, 154 side panel 188 system battery 211 system board 205 Windows 182 Internet 54 account 55 connecting to 56 downloading files 59 requirements to access 55 sharing access 136 transferring settings from old computer 153 troubleshooting 220 Internet connection sharing 136 troubleshooting 220, 224 Internet radio 93 Internet service provider (ISP) 54, 55 connecting to 56 disconnecting from 56 setting up account 55 transferring settings from old computer 153 InterVideo DVD Player 94 ISP See Internet service provider

SETTING UP YOUR GATEWAY COMPUTER
Your Gateway computer is packed with many powerful features. Icons and color coding help make setting up your computer as easy as possible.
FRONT (may vary with options)

DVD/CD drive

BACK (may vary with options)
Power connector Voltage switch Power connector Voltage switch Headphone/front speaker jack Microphone jack Optical out jack Center/subwoofer jack USB ports IEEE 1394/ FireWire port PS/2 keyboard port PS/2 mouse port Monitor port S-Video jack (optional) TV tuner (optional) Modem jack Telephone jack Case cover thumbscrew Monitor port Parallel port Serial port PS/2 keyboard port Monitor port (optional) If available, connect monitor here Modem jack Case cover thumbscrew Audio in/side speaker jack Surround left/right jack Ethernet (network) jack Headphone/front speaker jack Microphone jack Optical out jack Center/subwoofer jack USB ports
1 Connect the mouse and keyboard
If you have a wireless mouse or keyboard, follow the instructions that came with the mouse and keyboard.
DVD/CD drive (optional) Media card reader (optional) USB port (optional) Diskette drive (optional) Power button/ power indicator
Case cover thumbscrew Audio in/side speaker jack Surround left/right jack Ethernet (network) jack IEEE 1394/ FireWire port

otherwise

2 Connect the monitor
(depending on your model)
If available, connect to Add-in video (DVI or VGA), otherwise connect to Integrated video (VGA).
Add-in video (DVI or VGA)

Integrated video (VGA)

Hard drive indicator Microphone jack Headphone jack USB ports (optional) IEEE 1394/ FireWire port (optional)

PS/2 mouse port

S-Video jack (optional) TV tuner (optional) Telephone jack Case cover thumbscrew
USB powered step 1 USB powered step 2 AC Powered: 1 Plug the audio cable into the back of your computer. 2 Plug the round barrel power connector into the back of the right speaker. 3 Plug the other end of the power cable into a power outlet. AC step 1 AC step 2
3 Connect the speakers* (optional)
USB powered speakers, see USB steps. All others, see AC steps.
USB Powered: 1 Plug the audio cable into the back of your computer. 2 Plug the USB cable into one of your computer's USB ports.

AC step 3

FOR EXTRA HELP.
CONTACT HELP. If you need help while setting up your computer, call our Automated Troubleshooting System at 800-846-2118 and choose option 7. When prompted, enter 531 followed by #. If you need help after setting up your computer, visit the Gateway Support Web site at support.gateway.com. SEE YOUR STARTER GUIDE. After setting up your computer, read the Starter Guide for tips on using your computer. SEE YOUR ONLINE DOCUMENTATION. For detailed information about using your Gateway computer, see your User Guide that has been included on your hard drive. To access the User Guide, click (Start), All Programs, then click Gateway Documentation. CHECK GATEWAY SUPPORT. For help and information about common issues, visit the Gateway Support Web site at support.gateway.com.
SERIAL NUMBER AND CONTACT INFORMATION LABEL
Gateway Customer Care telephone numbers vary by country or region.
4 Connect the modem (optional)
Connect the modem cable to the modem jack and the telephone wall jack. You can connect your telephone to the telephone jack.
5 Connect the network (optional)
Connect the network (RJ45) cable to the Ethernet jack.
Gateway help resources and Customer Care information

Model and serial number

6 Connect the power cord
Connect the power cable to the computer, then plug it into a power supply. To protect your system from power uctuations, use a surge protector.
WARNING: To protect your computer during electrical storms, unplug the power cord and the modem and network cables.

7 Turn on the power ( )

Turn on the monitor and computer. Follow the Windows setup screen instructions.
IMPORTANT: Connect devices, such as a printer or scanner, after you complete the Windows setup. Follow the instructions that came with the device.
MAN 6BAY MBTX CONS PSTR V R0 10/06
Actual product may vary from image shown. Product specications subject to change without notice. 2006 Gateway, Inc. All rights reserved. Trademarks used herein are trademarks or registered trademarks of Gateway, Inc. in the United States and other countries. All other brands and product names are trademarks or registered trademarks of their respective companies.