P/N 30-10131

'06 BMW 325i/ 330i (E90) L6-3.0L
High Performance OE Replacement Air Filter
69% CFM Increase Over Stock!
Pleated depth loading media with large surface area provides high flow, high dirt capacity and high filtration efficiency.
Progressive bump seal requires no grease or gasket

*Tested on 2006 BMW 330i

Part Number MSRP UPC Box size Shipping weight 30-10131 $93.2.68" x 13.75" x 11.13" 3 lbs.
Restore Kits 90-50001 Gold Aerosol 90-50501 Gold Squeeze
Optimum Car Care Kit 90-90002
advanced FLOW engineering

Made in the U.S.A.

191 Granite St. Corona, CA 92879 951-493-7100 FAX 951-493-7177 www.aFefilters.com Specification, details and prices subject to change without prior notice.

40-12177

Intake Kit Installation Instructions: '06 BMW 325i/ 330i (E90) L6-3.0L
Kit Part # Make: Model 325i 330i 51/54-11012 BMW Year '06 '06 Engine L6-3.0L L6-3.0L Tools Required: 5/16 nut driver or slotted screwdriver 10mm socket or wrench Ratchet and extension 5/16 nut driver M6 allen wrench Part List: 1 Air filter (replacement # 24-91037) or Pro Dry STM 21-Intake tube 1 Tube Flange Gasket 1 Housing 1 Housing Cover 1 Coupler 3.5x2" 1 MAF gasket Step 1 Screw, slotted M4x7x16 Hex Head Screw M6x1x25 Nut M6x1 Flat washer M6 Clamp#056 Button Head Screw M6x1x10 Washer, Wavy M6 Injection Adapter
P.O. Box 1719 Corona, CA 92878 Support: 951-493-7100 www.aFefilters.com Step 1

Step 2

Step 3

Step 5

Complete kit. Make sure you have all the components listed prior to beginning your installation. Step 6
Disconnect the MAF sensor. Step 7
Loosen the hose clamp on the air box, and loosen the hose clamp on the intake manifold. Step 8
Loosen and remove the two 10mm bolts securing the air box to the chassis. Step 9
Remove the OEM air box assembly out of the engine bay.

Step 10

Remove the OEM intake tube.
Remove the MAF sensor from the OEM air box assembly.
Insert the MAF sensor assembly into the intake duct. Use the supplied gasket and screws. Secure the coupler to the intake tube using the #56 hose clamps. Do not tighten.
Slide intake tube onto the manifold, and secure clamps
Re-connect the MAF sensor plug.

Step 11

Step 12

Step 13

Step 14

Step 15

Insert the tube flange gasket between the housing and intake tube. Bolt the aFe housing onto the aFe intake tube. Secure the bolts. Secure the housing onto the chassis using three mounting locations, shown here. Install air filter and tighten using 5/16 nut driver. Tighten all clamps. (1) Make sure your center air intake tube sits onto the aFe housing (as shown). Place the aFe housing lid over the housing. Secure the lid with the 3 button head screws.
Your installation is now complete. Make sure you tighten all clamps and check all electrical connections. Re-check periodically.
Note: Filter Cleaning and Re-oiling: When cleaning your aFe filter, be sure to use only aFes Restore Kit (aFe P/N: 90-50001 blue oil aerosol, or aFe P/N: 90-50501 blue squeeze bottle oil or aFe P/N: 90-50000 gold oil aerosol, or aFe P/N: 90-50500 gold squeeze oil). Filter Replacement: Magnum FLOW PN: 24-91037 (black w/blue media). Pro Dry S P/N: 21-60507 (black w/ white media) Pro Dry S cleaning: see cleaning instruction sheet 06-00074or Pro-GUARD 7 PN: 72-90021.or 72-35008 Pro-GUARD 7 media, (black w/gold media). Pre-filters: 28-10011 yellow, 28-10012 red, 28-10013 black, and blue 06 80167