Connections

Chapter 3 >> Connections
Location of your receiver
Install your receiver in horizontal position Do not put any heavy stuff such as a TV on your receiver Do not install your receiver in the places as follows: Vibrating place, direct sunrays, Humid place, too high or low temperature, and no ventilated place.
Connecting your receiver with dish system
After installing your antenna system, connect the coaxial cable from the LNB of your antenna to DISH INPUT terminal marked at the rear panel of your receiver. All cable connectors should be finger-tightened; do not use any kind of wrench while tightening connectors. The cable should be 75 ohm impedance coaxial twisted at the end with an F type connector.

10 English

Connecting your analog receiver
To facilitate the user using analog receiver to view analog channels, this product has been provided with a loop through terminal marked as Loop. Connect the coaxial cable from this terminal to the IF input terminal of your analog receiver. Now by keeping your receiver in standby, you will be able to tune and view analog channels from your analog receiver.
Connecting your receiver to TV
To connect your receiver with your television, you can use 4 different methods; via RCA cable, SCART cable, HDMI cable or YUV. Connect the RF cable to the terminal marked RF OUT on the rear panel of your receiver and its other end to the TV RF input socket. Connect the Video/Audio RCA cables from the Video OUT/AUDIO OUT (LEFT, RIGHT) on the rear of your receiver to the Video INPUT/AUDIO INPUT (LEFT, RIGHT) jacks on the TV. In the case of connecting your TV through SCART cable, connect the SCART connector marked TV to the respective SCART port on the TV. (depend on model) Connect the HDMI cable to the terminal marked HDMI on the rear panel of your receiver and its other end to the TV HDMI input.
Connecting your receiver to VCR (depending on model)
To connect a VCR, your receiver has been provided with SCART at the rear marked VCR. Using a SCART connector, the VCR can be connected to your receiver.
Connecting external audio/Hi-Fi system
To connect any external Audio Hi-Fi system, your receiver has been provided with two RCA connectors at the rear panel of your receiver, marked with AUDIO L and R respectively to connect the left and right Audio on the external audio/Hi-Fi system.

Antenna Setting Tuner 1

You can set antenna and LNB information for scanning channels. If antenna is not correctly set, you cannot scan channels, therefore you cannot watch any programs. 1 Select Antenna Setting using the Arrow (/) buttons and press the OK button. Antenna setting menu appears. 2 Select satellite for channel scan using the Arrow (/) or Page (+/-) buttons and press the Arrow (/) button to select at option. 3 Select an option using the Arrow buttons. LNB Power: On or Off (Defaulf: Off) Longitude: Using Defaultmode LNB Type: Universal 1, Universal 2 (Default

Universal 1)

LNB Freq: Frequency can be input with
numeric key with RCU DiSEqC Port:1~4 for 1.0 and Tone Burst 1~2 and Off. Tone 22kHz: On, Off or Auto (Default: Auto) Unicable: Press OK Button to choose one IF by Auto detection Motor: Moving Antenna unsing DiSEqC1.2 or USALS DiSEqC1.1: Uncommited DiSEqC Command 1-16

English 13

Antenna Setting Tuner 2
1 Select Antenna Setting for tuner 2 using the Arrow (/) buttons and press the OK button. 2 Select one of the following options: Same Signal: Same configuration as tuner 1 Loop Through - Cable from tuner 1 loop through tuner 2 Separated: Tuner 2 has a different connection. After selecting this options the same menu as tuner 1 comes up and you have to select the options.

Installation Options

1 Select one of the following options using the Arrow (/) buttons. Option 1: Auto Scanning see page 15) Option 2: Download Channel list from Astra You can select from different channel lists. Select you desired list and press OK Key. Option 3: German Channel list 2 Press OK Key.

14 English

Auto Scanning
1 Select Auto Scanning using the Arrow (/) buttons and press the OK button. The preprogrammed satellite lists will appear. 2 Select an appropriate satellite using the Arrow (/) buttons and set the channel options using the Arrow (/) buttons. Off: Scanning is disabled. All: Scan all the free and scrambled channels. Free: Scan free channels only. NIT: Scan all mode with TP network scanning. You can set Off, All, Free or NIT to each satellite. 3 Press the OK button, Auto Scanning will start. All the channels in the list from the selected satellite will be automatically downloaded. 4 Press the OK button to save the changes. 5 Press the Back ( ) button to exit from the menu and press the Arrow (/) buttons to select the desired channel. Now you can watch TV or listen to the Radio.
For more information on scanning a satellite see chapter 5!!

English 15

Terrestrial (optional) Auto Scanning
1 Press OK Key to start Auto Scanning. 2 Press the OK button to save the changes. 3 Press Back Key button to exit from the menu and press the Arrow (/) buttons to select the desired channel. Now you can watch TV or listen to the Radio. You can no select the channel using arrow buttons (/)

Basic Operation

This section explains various functions while watching TV or listening to the Radio.

Switching Channel

You can switch the current channel by three different methods. Method 1: Press the Arrow (/) buttons or PR+/- buttons. Method 2: To select a channel directly, select a channel using the Numeric (0~9) button. Method 3: 1 To display the channel list, press the OK button. 2 Select a channel you want to watch using the Arrow (/) buttons and then press the OK button. If there are multiple channels, use the Page (+/-) or the Arrow (/) buttons to move to channels by page. ) button to switch between the TV and Radio channel. Press the Mode ( Method 4: In case of more than two scanned satellites 1 Press the SAT( ) button to show satellite list. 2 Move the cursor to the satellite of a channel to watch with the Arrow (/) buttons and then press OK button. 3 You can follow the method 3 instruction for channel selection. Method 5: How to move to the watched channel. 1 Press the last button with RCU. 2 Press OK button after a channel selection by using the Arrow (/) with RCU. 3 Press OK button to exit.

Volume Control

To control the volume: Press the VOL+/- or the Arrow (/) buttons. Press the Mute ( ) button to turn the sound off. Press the Mute ( ) button again or the VOL+/- or Arrow (/) buttons to cancel muting.

16 English

Info Bar
Channel information always appears for a specific period of time whenever you switch channels. General Information Press the INFO button; you can see general information of the current channel. 1 Channel number and name 2 Current time 3 Signal Level 4 Signal Quality 5 Icons: HD channel, Locked channel, Radio Channel, Scrambled channel, Subtitle, Teletext information 6 EPG information. 7 Conditional Access Detailed Channel Information You can see detailed channel information pressing the INFO ( ) button again. 8 You can see detailed channel information pressing the INFO button again. 9 Satellite, Frequency, Symbol Rate, FEC, Polarity, Video PED, Audio PID, PCR PID, Transponder 10 Display the stream information.

Selecting the soundtrack

You can select the audio language, soundtrack, or sound mode. 1 Press the Audio (Yellow) button. 2 Press the Arrow (/) buttons to select the audio language or soundtrack and press the OK button. 3 Press the Arrow (/) buttons to select the sound mode from Stereo, Mono left, or Mono Right. 4 Stream information.

Selecting the OSD teletext, VBI teletext, Subtitle and DVB subtitle
You can choose the OSD teletext, VBI teletext, subtitle and DVB subtitle for the current live TV program if provided from the broadcasting station. OSD teletext: Press the Text button VBI teletext: Press the Text button twice. Subtitle: Press the Text button three times. DVB subtitle: Press the Text button four times.

English 17

Sleep Timer Function
Press the GREEN (Sleep) button, you will see the time set for the sleep timer if already set from the Time Setting menu.

Zoom Function

You can make the picture appear larger on the screen pressing the Zoom ( ) button. 1 Press the Zoom ( ) button. 2 Select the area you want to zoom using the Arrow buttons and then press the OK button. Picture is enlarged two times. 3 Each time you press the Page (+/-) buttons, the picture is enlarged two or four times. Press the Arrow (///) buttons to change the location at the lower right of display. 4 To cancel the Zoom function, press the Zoom ( ) button twice or Back button.

Channel List

You can see the TV or Radio channel list pressing the OK button while watching TV or listening to ) button. The icons behind channel the Radio. Switch the channel list pressing the Mode ( names reflect the status of the channel like scrambled or locked. Select channel using the Arrow (///), PR+/-, or Page (+/-) buttons and press the OK button to watch. The colored buttons show the channel lists as follows: Red Key: sort channel alphabetically GREEN button: by satellites (all/searched satellites) YELLOW button: by names of broadcasting providers Blue button: by HD channels Opt : Enter channel list menu to move, delete or rename channels

18 English

To view channel list in specific order (Alphabet/Satellite/Provider/HD)
1 Press the Colored (Red/ Green/Yellow/Blue) button. Channel list is highlighted. 2 Select Alphabet, Satellite, Provider, or HD using the Arrow (/) buttons. The channel list is sorted automatically by your selection. 3 Select the channel pressing the Arrow (/) or Page ( / ) buttons and press the OK button to watch it.
Electronic Program Guide (EPG)
EPG displays program information such as program titles, broadcasting schedule, Program synopsis and such EPG service differ depending on the service provider. 1 Press the GUIDE button while watching TV or listening to the Radio EPG information appears. 2 Select a program for further more information. Arrow (/) buttons: Selects a program by channel Arrow (/) buttons: Selects a program by time & date within the same channel. It displays the program list at 30 minutes intervals. You can see the detailed information by pressing Page (+/-) buttons with RCU. 3. Press the OK button, detailed information on the selected event appears. 4 Press YELLOW Key to switch Viewmodes in EPG (Multi vs. Single Channel). 5 To jump one day ahead press BLUE KEY. 6 To jump one day back press RED KEY. 7 To record a transmission press GREEN KEY. Read more in the PVR-Chapter !! 8 To exit from the EPG mode, press the Back button

English 19

Chapter 5 >> Main Menu

20 English

Main Menu
The menu has been carefully designed from user-friendly point of view to assure easy operation to your receiver. The main menu is classified into 7 sub menus that will carry out the various operations individually.

Installation

In the Installation menu, you can customize antenna setting and do channel scanning. Press the Menu button. Select Installation using the Arrow (/) buttons on the main menu.
Installation >> Antenna Setting
Antenna Setting TUNER 1 or Tuner 2
You can set antenna and LNB information for scanning channels. If antenna is not correctly set, you cannot scan channels, therefore you cannot watch any programs. 1 Select Antenna Setting using the Arrow (/) buttons and press the OK button. Antenna setting menu appears. 2 Select satellite for channel scan using the Arrow (/) or Page (+/-) buttons and press the Arrow (/) button to select at option. 3 Select an option using the Arrow buttons. LNB Power Set LNB Power On. Longitude If you know the exact longitude of your location, use the Numeric (0~9) buttons. Toggle between E (East) and W (West) using the Arrow (/) buttons. LNB Type(Unicable) Select the LNB type by pressing Arrow (/) button - Universal 1 (9750 / 10600) - Universal 2 (9550 / 10750) - Unicable (1210 IF / 1420 IF / 1680 IF / 2040 IF) Select the Unicable and press OK Button to choose one IF by Auto detection (When you use Unicable, Blind Scan function will be not supported) - User Define (LNB Low / LNB high) LNB IF Frequency can be input with numeric key with RCU - Standard (5150 / 9750 / 10000 / 10600 / 10750 / 11250 / 11300 / 11475)

English 21

Note What is Low Noise Block (LNB)? The LNB is located at the satellite dish antenna. It amplifies the very weak received satellite signal then converts the received microwave satellite signal so that the signal may not decrease the gain between the dish and your receiver. DiSEqC (Digital Satellite Equipment Control) Mode You can select DiSEqC using the Arrow (/) buttons. You can select one mode among DiSEqC Port1~4 for 1.0 and Tone Burst 1~2 and Off. Tone 22KHz In case you are using a dual LNB or two antennas connected to a 22KHz Tone Switch Box, with 22KHz Tone Switch (On, Off, or Auto) you can switch between LNB or antenna. Motor Select motor setting from DiSEqC, USALS, Positioner, and No. DiSEqC 1.1 In case of DiSEqC 1.1 usage, select port 1~16 for the satellites by using the Arrow (/) button. Signal Status Press the blue button, you can check the signal status for each TP and Satellite with the Arrow (//) buttons. You can scan the selected satellite and TP and save the changes. - Green button: Satellite Auto Scan - Yellow button: TP Scan 4 After setting the option, press the OK or RED button to save. Select satellite(s) according to the direction of your satellite dish. You can select many satellites depending on the direction to the satellites 5 Press the Back button to return to the Installation menu. Anmerkung DiSeqC is the registered trademark of Eutelsat Communications. A standard through which is possible to let a DiSEqC compatible receiver send a signal over the RF cable to a switching device to switch between different LNBs or dishes. The DiSEqC uses the 22KHz signal to control the switching device

22 English

Installation >> Tuner (1 or 2) >> Motor Settings

Motor Settings

DiSEqC 1.2 If Motor is set to DiSEqC 1.2 in the Antenna Setting men. 1 Select Motor Setting using the Arrow (/) buttons and press the OK button. 2 Select a satellite using the Arrow (/) buttons and press the OK button. Satellite list appears. Select satellite using the Arrow (/) buttons and press the OK buttons. Bulleted list indicates selected satellites. 3 Press the RED button to save selected satellites and then press the Back button. 4 If you press the YELLOW button, on-screen navigation menu is highlighted. Use the Arrow buttons to move the motor to the west, east, north, and south in order. The position of the motor can be restricted to the software setting limits (West/East) using the RED / BLUE buttons. 5 Press the YELLOW button to highlight Satellite. 6 Press the OK button on the Go to satellite Menu. Dish changes its position to the direction of satellite (depending on the types of motor, dish changes its position to the default-direction of satellite for the maximum 28 satellites). 7 Press the OK button on the Save Current Position menu. Current position of the motor is saved according to the selected satellite. 8 You can change the Function Menu (Go to Ref. Position / Reset Position / Calculate Positions) by using the Arrow (/) button, activate the function with OK button - Go to Ref. Position: Press the OK button in the Go to Ref. Position menu. Motor changes its position to zero longitude / latitude where the count begins. - Reset Position: Reset Positioner initialize the position of motor to the default value. - Calculate Positions: Calculate Positions selects one satellite to revise the position of motor and saves the changes. Changed position of the motor also applies to the directions for other satellites.

English 23

9 Confirm the Enable Limits/Disable Limits function pressing the OK button. You will be prompted to decide whether to use the West/East setting Limits setting value. 10The method to position motor is selected in the Continuous/Step (Impulses)/Time (Seconds) menu. If you press the Arrow (/) buttons once in the Continuous mode, selected TP signal of the satellite is locked or the motor stops to move. In the Step (Impulses) mode, you can select Steps (Pulse) from 1 to 10. The motor changes its position according to the selected step if moved to the left or right (depending on the motor). In the Time (seconds) mode, you can select time (seconds) from 1 to 20. The motor changes its position according to the selected step if moved to the left or right (depending on the motor). USALS 1 Select Motor Setting using the Arrow (/) buttons and press the OK button. 2 Select Satellite menu using the Arrow (/) buttons and press the OK button. Satellite list appears. Select satellite using the Arrow (/) buttons and press the OK button. Bulleted list indicates selected satellites. 3 Press the RED button to save selected satellites and then press the Back button. 4 If you press the YELLOW button, onscreen navigation menu is highlighted. Use the Arrow buttons to move the motor to the west, east, north, and south in order. Position of the motor can be restricted to the software setting limits (West/East) using the RED / BLUE buttons. 5 Press the YELLOW button to highlight Satellite. This function may not work depending on the type of USALS program. 6 Enter the value of 000.0 E/W (latitude) and 000.0 N/S (Longitude) and then press the OK button on the Go to X menu. Motor changes its position according to the selected satellite. 7 Confirm the Enable Limits/Disable Limits function pressing the OK button. You will be prompted to decide whether to use the West/East setting Limits setting value. This function may not work depending on the type of USALS program. Press OK in Go to Reference menu, the motor moves at zero longitude/latitude.

English 25

Installation >> Tuner (1 or 2) >> Auto Scanning
If you select the satellite to scan channel according to the antenna setting, your receiver can automatically scan the satellite without entering any other information. 1 Select Auto Scanning using the Arrow (/) buttons on the Installation menu and press the OK button. 2 Select satellite to scan channels by using the Arrow (/) buttons and select scan mode (All, Free or NIT) using the Arrow (/) button. All: Scans all channels. Free: Scans free channels only. NIT: Scan All mode with TP network scanning. 3 Press the OK button, and then it starts scanning. After Auto Scanning completes, you can see TV and Radio channels in the list.
Installation >> Manual Scanning

Manual Scanning

You can scan channels of the selected satellites by transponders if you know the transponder information. 1 Select Manual Scanning using the Arrow (/) buttons on the Installation menu and press the OK button. 2 Set the following options to complete Manual Scanning. Satellite: Select a satellite by using the Arrow (/ /) buttons or Page (+/-) buttons. Transponder: Set the transponder for the selected satellite. Select a transponder using the Arrow (/) buttons.

26 English

If you cannot find your desired transponder, select New to change transponder information as follows: Frequency Display the selected TP Frequency. Symbol Rate Display the selected TP Symbol Rates. FEC (Forward Error Correction) Select a FEC option Auto, 1/2, 2/3, 3/4, 5/6, and 7/8 using the Arrow buttons. Polarity Select a polarity value among Horizontal, Vertical, Circular Left, and Circular Right using the Arrow buttons. Horizontal output is 18V and Vertical output is 13V via LAN. Note What is a transponder? A wireless communications device usually attached to a satellite. A transponder receives and transmits incoming signals with in a prescribed frequency range. After receiving the signals the transponder will broadcast those signals with different frequencies. Scan Mode Decide whether to find free channels only or all the channels including scrambled ones. Select a scan mode using the Arrow (/) buttons. All: Scans all types of channels. Free: Scans free channels only. NIT Search You will be asked whether to search channels for another transponder. Select either Yes or Off using the Arrow (/) buttons. Select Yes to run Network Search. PID Search You can manually scan channels by entering individual Packet Identifier (PID) values. Enter the PID the Numeric (0~9) buttons. First, select a PID type (Video PID, Audio PID, or PCR PID) using the Arrow (/) buttons, then enter the PID value by pressing the Numeric (0~9) buttons. 3 Press the OK button, then starts scanning. After Auto Scanning is complete, you can see TV and Radio channels found from Auto Scanning.

English 27

4 Press the RED (MoSAiC) button on the Manual Scan menu Satellite: Select the satellite by using Arrow (/ /) buttons or Page (+/-) buttons Transponder: Change the TP with the Arrow (/) buttons Frequency: Displays the current Frequency Symbol Rate: Displays the current Symbol Rate FEC (Forward Error Correction): Displays the current FEC Polarity: Displays the current Polarity Add TP: Press the Green (Sleep) button for a new TP add Del TP: Delete the current TP with Yellow button RED button: Save the TP information

Blindscan

1 Press OK Key to open Blindscan menu. 2 Select Start- and Endfrequency from the area that would you like to search. 3 Select the stepping for searching for transponders. 4 Select polarisation. 5 Select if you want to limit your search for FTA channel or choose all channels. 6 Start blindscan with OK Key. Note: Blindscan search the satellite for every carriers; even undocumented If the receiver find some channels or transponders he will automatically add it to your channel/transponderlist.

28 English

Installation >> Defaults Setting

Defaults Setting

You can restore the default setting in case you have encountered some problems after saving changes to channel data and others that may be in error. 1 Select Defaults Setting using the Arrow (/) buttons on the Installation menu and press the OK button. 2 Select a defaults option (Factory Defaults, or STB Reboot) using the Arrow (/) buttons and press the OK button. Factory Defaults: Resets back to the factory-default settings. If you press the OK button in this menu, you will see a dialog box asking you to confirm the channel defaults or factory defaults setting. Select Yes or No, and press the OK button. STB Reboot If you press the OK button in this menu, the Set-top box (STB) reboots.

System Setup

You can set the system configuration in this menu. Press the Menu button. Select System Setup using the Arrow (/) buttons on the menu.
System Setup >> Language Setting

Language Setting

You can set languages for OSD, Audio 1-2, Teletext, Subtitle, and EPG 1-Select Language Setting using the Arrow (/) buttons on the System Setup menu and press the OK button. 2 Select any of OSD, Audio1- 2, Teletext, Subtitle, and EPG1-2 languages using the Arrow (/) buttons and use the Arrow (/) buttons to select its language.

English 29

System Setup >> OSD Setting

OSD Setting

You can adjust OSD Transparency, Window Trans OSD Banner Time, and Screen Saver Time. 1 Select OSD Setting using the Arrow (/) buttons on the System Setup menu and press the OK button. 2 Select any of Transparency, Window Trans, Screen saver Time, VFD Module and Display in Standby Mode, and Screen saver Time using the Arrow (/) buttons and use the Arrow (/) buttons to make changes. Transparency: 0 (opaque) to 100% Window Trans: 0 (opaque) to 100% Banner Time: 1 to 60 seconds or Always Screen saver Time: 1 to 60 minutes or None Serial Module: X-crypt or None

English 35

Channel Setup >> Software Manager

Software Manager

You can download the software of your receiver through satellite when the new software is available for your system. During download, dont turn off your receiver. In case of the power is turned off, turned on your receiver again to complete the download. 1 Select Software manager using the Arrow (/) buttons on the Installation menu and press the OK button. Software Upload: Copies all the data from Master STB to Slave STB. Channel Upload: Copies only the channel data from master STB to Slave STB. Connects both Master and Slave STB using RS232C Cable and then press the OK button on the Software Upload menu for the Master STB. OTA Software Download: Main Software can be updated over the air. OTA Channel Download: Channel Data can be updated over the air.
Info: OTA means that new software are updated Over The Air. New software also means there are new functions and fixed errors. Keep you software up to date with OTA Software Downloads

Parental Lock

You can lock the channels to prohibit unauthorized users from watching specific channels. Press the Menu button. Select Parental Lock using the Arrow (/) buttons on the main menu
Parental Lock >> Channel Lock

Channel Lock

Whenever you want to see the locked channel you will be prompted to enter the PIN Code in the dialog box. 1 Select Channel Lock using the Arrow (/) buttons on the Parental Lock menu and press the OK button. 2 Select the channel that you want to use the Arrow (/), PR+/-, Page (+/-), or Numeric (0~9) buttons and press the OK button. Selected channel will be displayed with lockingmarked. Press it again to clear. Arrow (/) buttons: Switches between TV and Radio List. 3 Press the RED button to confirm. 36 English

Jugendschutz

Parental Lock >> Lock Control

Lock Control

Whenever you want to use the locked system you will be prompted to enter the PIN Code in the request dialog box. Using Arrow (/) buttons and press OK button to select a lock status. System Lock: Select Lock or Unlock by using the Arrow (/) button. If Lock is selected, the front key function will be blocked. Menu Lock: Select Lock or Unlock by using the Arrow (/) button submenu Lock control will be available with PIN code. Lock mode: Select Once or Every time mode by using Arrow (/) button. Once: Input the pin code once on the channel change with Parental Lock. Every time: Input the pin code every time on the channel change with Parental Lock Save the changes with OK button

Change PIN Code

Parental Lock >> Change PIN Code
You can create a new PIN code in this menu. 0000 is the default password. 1 Select Change PIN Code using the Arrow (/) buttons on the Parental Lock, System Lock, Menu Lock and press the OK button. 2 Enter the old PIN code. 3 Enter the new PIN code. 4 Enter the new PIN code again to confirm. Note Please keep in mind that the PIN code must be a four-digit number. In case you forgot your PIN code, contact your local dealer.
This product provides lots of games for your entertaining environment. Select Game using the Arrow (/) buttons on the main menu. 1 Select a game using the Arrow (/) buttons on the Game menu and press the OK button. 2 According to the instruction displayed on screen, you can enjoy games using the Arrow, Numeric (0~9), and OK buttons.

English 37

Multimedia
This menu offers you to access your multimedia devices USB, Internal harddisk and ethernet.
Multimedia >>PVR Setting
You can find detailed infiormations about PVR Settings in Chapter PVR Function from site 42.
Multimedia >>Player Setting
Vantage Player Time: Set the timeout for the Vantage Player function menu. Auto Resuming: Enable to resume playback from last position. Playback Repeat: Enable instant repeat if playback is finished JPEG- Slide Show: Set timeout on photo slide show.

38 English

Multimedia >> Internal Hard Drive
Connect the external HDD through SATA connector in the rear panel. HDD must be compatible with FAT 32 file system. If HDD is not compatible with FAT 32 File system, you need to change the file system. By using personal computer with the format function. 1 Playing the media files Select the media file with channel up/down buttons and press OK button. 2 Software Update Select S/W files with channel up/down buttons and press Red key. 3 Deleting files Select the files with channel up/down buttons and press Green key. 4 Format Press yellow key to delete all the files in the storage device.

Multimedia >> USB 1 und USB 2
You can use exernal harddisks or USB storage devices ( USB Stick) as data storage. Note: All external Storage devices must be formatted with FAT 32. You can format your devices, if needed, by pressing the yellow key. 1 Playback media files Select the mediafile you want to playback by navigating with your navigation keys and activate with OK. You can playback the following file formats: Xvid, JPEG, MP3
MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson 2 Software Update Select S/W files with channel up/down buttons and press Red key. 3 Deleting files Select the files with channel up/down buttons and press Green key 4 Format Press yellow key to delete all the files in the storage device.

English 39

Multimedia>> Network (optional)
Before starting setup, please check if the Ethernet cable is connected to your receiver well.
1) TCP IP set up Input the right information for the settings to the followings. TCPIP Type/ IP Address/ Net mask / Gateway/ DNS Type/ DNS Server Note: The suggested setting is DHCP(Dynamic Host Configuration Protocol). This option configurates your network automatically.
2) FTP Explorer Press O.K. to connect the FTP Server Select file and press Red Key for S/W update. You cvan download pictures, firmware and video files

40 English

Conditional Access
Condtional Access CI A CI B CA A CA B Common Interface Slot 1 Common Interface Slot 2 Card reader 1 Card reader 2
Your receiver is equipped with 2 Common Interface Slots. In this Slots you can use every standard Common interface module : Irdeto, Viaccess, Cryptoworks, Conax und Mediaguard. To watch scrambled channels you will need a common interface modul and a descrambling card that must match system wise. Your card ( provided by TV provider ) must be slide in your common interface module. The Common Interface module must be positioned in on of the 2 CI slots. You can access internal menus of your CIs via menu Conditional Access. Documentations about your card or module will be provided by your pay tv provider. Beside CI slots your receiver is equipped with two card readers for smart cards. The card readers support the following encryption systems: dgcrypt, conax, firecrypt, xcrypt, crypton You can access internal menus of your smart cards via menu Conditional Access. Documentations about your cards will be provided by your pay tv provider.

46 English

Chapter 2 >> Comfort Functions

Comfort features

In this chapter we introduce you to some comfort function of your STB.

PiP: Picture in Picture

You can start PiP by pressing the PiP Key. In this mode your program will move to a small picture in the upper right quadrant of your screen. You can now change the channel on your main screen by using the numeric Keys, CH+/- Keys or by using the channel list. Press the SWAP Key to switch between your PiP and Main screen. Finish this function by pressing the PiP Key.

MoSAic

Press the RED Button (MoSAic) to open up this function. You can choose from a menu how many screens you wan to use for this feature. You can choose between 2 x 2 pictures or 2 x 3. In this mode you get an overview about 4 or 6 channels on your screen. The actual pictures will be refreshed one after another. You can switch to next channels in your channel list by pressing the Blue Button and move backwards with the RED Button. You can use your navigation keys to move to every of this small screens and activate it to live mode using the OK button. If you want to see a this channel on your main screen press OK again.

Teletext Navigation

Open Teletext by pressing the Text Button. A popup menu let you (if available) choose between teletext languages. Choose your language and confirm with OK. Now you can use teletext services you can go to teletext sites directly by addressing it with your numeric keys or you can move site wise with your Up and Down Keys.

Favorites

Your Receivers offers the opportunity to organize your favorite channels in so called favorite lists: (see page 33/34) You can access your Fav lists directly by pressing the FAV Button. Push the button again to move to the next Fav list Please press this button again to move back to your main channel list.

English

Troubleshooting
Problem No display LED on the front panel. No power supply No picture. Ensure that the STB is switched on. Check the connection status. Check channels and Video output status. Poor picture quality. Check the signal level If this is too low, try adjusting the alignment of your dish. No sound. Check the volume level of the TV and STB Check the mute status of the TV and STB Check the connection of audio cable. Remote Control does not operate. Point remote control directly towards your receiver. Check and replace batteries. Check if anything blocks the front panel. Service is not running or scrambled. Make sure the smart card is appropriate for the selected service. You have forgotten your PIN code. See chapter 5, Parental Lock in this Users manual. Solution Plug the power cord correctly.

Network (Optional)

This Manual is based on Firmware version: 02.20T-O. 50 English
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, Please separate this from other types of wastes and recycled it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Correct Disposal of This Product

English 51

Glossary Glossary
DiSEqC: is a special communication protocol for use between a satellite receiver and a device such as a multi-dish switch or a small dish antenna rotor. DiSEqC was developed by European satellite provider Eutelsat, which now acts as the standards agency for the protocol. DiSEqC is available in serveral versions: DiSEqC 1.0, which allows switching between up to 4 satellite sources DiSEqC 1.1, which allows switching between up to 16 sources DiSEqC 1.2, which allows switching between up to 16 sources, and control of a simple horizontal-panning satellite motor DiSEqC 2.0, which adds bi-directional communications to DiSEqC 1.0 DiSEqC 2.1, which adds bi-directional communications to DiSEqC 1.1 DiSEqC 2.2, which adds bi-directional communications to DiSEqC 1.2 Symbolrate: This value indicates the data transfer speed. If you need this information to setup your receiver ( satellitescan) you will find it for instance under: www.lyngsat.com. Polarization: Satellite reception works with two polarizations. That is because the bandwith capacity can be used more efficient. In the european area the polarisatzions usually are devided in vertcal and horizontal layers. Receiver access those layers by using different power thru ZF. 14 V for vertical and 18V for horizontal. 22KHz: Das 22 KHz Signal wird benutzt um im LNB zwischen den zwei vorhandenen Frequenzbereichen umzuschalten. lower frequency range: The lower frequency range is 10.70 - 11.70 GHz ( input frequency) upper frequency range: The upper frequency range is 10.70 - 11.70 GHz ( input frequency) SPDIF S/PDIF specifies a Data Link Layer protocol and choice of Physical Layer specifications for carrying digital audio signals between devices and stereo components. The name stands for Sony/Philips Digital Interconnect Format (more commonly known as Sony Philips Digital InterFace), the two companies being the primary designers of the S/PDIF format

Manual for streaming between 2 Vantage HD Receiver

Z.B.: HD 8000 als Master

Choose this option in menue
After config this option press the red button to save. Now press Connect to browse on Master Receiver
After config this option press the red button to save.
HD 1100/7100/8000 as Slave