Technical Support

PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH YOUR PRODUCT. By registering your product at www.NETGEAR.com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades. NETGEAR, INC. Support Information Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support See Support Information card for other countries. E-mail: support@NETGEAR.com (24 x 7 online support) www.NETGEAR.com
Fast Ethernet Switch 10/100 Mbps FS605 v2/FS608 v2
2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved

Installation Guide

M-10160-01

August 2003

Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the product described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

Introduction

The NETGEAR 5/8-Port Fast Ethernet Switch Model FS605 v2/FS608 v2 provides you with a low-cost, reliable, high-performance switch to connect up to five or eight different Ethernetenabled devices (such as computers, file servers, print servers, printers, routers and hubs).
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Fast Ethernet Switch FS605 v2/FS608 v2
You use the FS605 v2/FS608 v2 switch to build a small network that enables you to have 10 Mbps or 100 Mbps access to other devices on the network. Also, with this switch, you can add extra computers to your cable or DSL router. Unlike a hub that shares its connection with all devices, the FS605 v2/FS608 v2 switch provides a full, dedicated 100 Mbps (or 10 Mbps) connection between two devices. If a device has full-duplex capability, the FS605 v2/FS608 v2 switch provides a 200 Mbps (or 20 Mbps) connection. Ethernet cables come as either straight-through or crossover cablesdepending on whether youre connecting to a device (computer, server, or printer) or networking equipment (hub, switch, or router). With the Auto Uplink feature, you dont have to worry about which one you use. Each port on the FS605 v2/FS608 v2 switch automatically configures itself correctly when you plug in a devices cable. If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7 days a week on the Web (www.NETGEAR.com), by e-mail (support@NETGEAR.com) and by phone (see the provided support information card for phone numbers).

EN Declaration of Conformance
This is to certify that the NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN Class B (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Rglement sur le brouillage radiolectrique du ministre des Communications
Cet appareil numrique (NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch) respecte les limites de bruits radiolectriques visant les appareils numriques de classe B prescrites dans le Rglement sur le brouillage radiolectrique du ministre des Communications du Canada.

Installation Overview

Estimated Time: 510 minutes 1. 2. 3. Unpack the box and verify the contents. Prepare to install the switch. Install the switch and connect the other devices.
Unpack the Box and Verify the Contents
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface such as a table, desk or shelf. The switch comes with wall-mounting screws and a vertical stand. Youre welcome to use the screws if you want to hang the switch in an open space on a wall. Use the vertical stand if you cannot provide adequate clear space on all sides with the switch in a horizontal position. Make sure the selected location is: Not in direct sunlight or near a heater or heating vent. Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. Well ventilated (especially if it is in a closet).
Installation guide, warranty/registration card and support information card
Also, youll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).

Power adapter

When you open the box, verify that you received everything. The package includes: 5/8-Port Fast Ethernet Switch FS605 v2/FS608 v2 AC power adapter Wall-mounting screws FS605 v2/FS608 v2 Installation Guide (this document) Warranty and support information card
If you dont have everything listed above, see the support information card for contact information. If youre missing the Technical Support information card itself, get contact information at www.NETGEAR.com in the Customer Service area.

Install the Switch and Connect the Other Devices

Troubleshooting

The Power light is not lit
The switch has no power. Make sure the power cord is properly connected to the switch. Make sure the power adapter is properly connected to a functioning power outlet. If its in a power strip, make sure the power strip is turned on. If the socket is controlled by a light switch, make sure the switch is in the on position. Make sure you are using the NETGEAR power adapter supplied with your switch.
The Port number light is not lit for a connected device or stays on continuously

DSL modem

Theres a hardware connection problem. Make sure the cable connectors are securely plugged in at the switch and the device. Make sure the connected device is turned on. If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card or adapter is installed correctly and is working. Make sure the cable is less than 328 feet (100 meters).
Fast Ethernet Switch FS605 v2
Fast Ethernet Switch FS608 v2

Technical Specifications

Standards Compatibility: Data Rate: Network Interface: DC Power: Physical Dimensions: Weight: Operating Temperature: Operating Humidity: Electromagnetic Compliance: Safety Agency Approvals for the Power Adapter: IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet IEEE 802.3x Flow Control; compatible with Windows, Mac OS, NetWare, Linux 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX 10 or 100 Mbps half-duplex RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface 7.5 W max and 7.5 V @ 0.8A DC input FS605 v2 - W: 116.37 mm (4.58") D: 89.75 mm (3.53") H: 34.42 mm (1.36") FS608 v2 - W: 158.37 mm (6.24) D: 89.75 mm (3.53) H: 34.42 mm (1.36) FS605 v2 - 0.13 kg (0.287 lbs); FS608 v2 - 0.18 kg (0.397lbs) 0 to 40 C (32 to 104 F) 10% t0 90% relative humidity, non-condensing CE mark, Commercial; FCC Part 15, Class B; EN (CISPR 22) Class B, VCCI Class B, C-Tick CE mark, Commercial UL listed (UL 1950), TUV licensed (EN 60950), C-Tick
Place the switch on a flat surface or hook onto the screws. For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch.
Note: If you have more than 5 or 8 devices to connect to this switch, you must connect them to a hub or other switch and then connect that hub or switch to this switch.
Connect the power adapters cord into the back of the switch and then plug the adapter into a power source (such as a wall socket or power strip). The Power light should light up. The corresponding port number for each connected and powered device should light when link (connection), and flash when activity occurs.
Note: If any light doesnt operate as indicated, go to the Troubleshooting section.
Performance Specifications 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port Frame Filter Rate: Frame Forward Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port Network Latency: 100 Mbps to 100 Mbps: 20 s max

8-port Fast Ethernet Switch

10/100 Mbps

Expand your network easily & attractively
Help is there when you need it! NETGEAR provides 24x7 technical support* in English, with selected local language support during office hours.
Hang on your network will soar when its hooked up to NETGEARs FS608! This powerful plug-and-play switch connects at 10 or 100 Mbps and makes it easy to link as many as eight computers or peripherals to your Ethernet network. Youll experience maximum performance for 10 or 100 Mbps devices with eight ports that automatically sense the correct speed while Auto Uplink on the ports adjusts for the different types of Ethernet cables. Use the WGEMbps Wireless Ethernet Bridge to link multiple devices to your wireless network without new wireless adapters. The FS608s sleek case has lights on the front for easy monitoring. Installation into your home or small office network couldnt be simpler and, once powered on, it begins cool and silent operation without an internal fan.

Versatile

Connects up to eight computers, servers, printers, switches or any other Ethernet devices at 10 or 100 Mbps over Ethernet cables. Works with virtually any operating system (Microsoft Windows, Apple Macintosh, Linux and more). Use the WGEMbps Wireless Ethernet Bridge to link more devices to your wireless network without new wireless adapters.

User-Friendly

Designed specifically for home and small office users with Plug-and-Play installation, rear ports that reduce cable clutter, and front status lights for easy monitoring. Plug it in, set up your Ethernet devices, and you will forget that it is even there.

Resourceful

All eight ports deliver automatic speed and duplex sensing, plus Auto Uplink adjusts for different Ethernet cable types to make the right link every time.

Well-Designed

Sleek, attractive, platinum design blends seamlessly into your home decor.

Everybodys Connecting.

Internet

POWER CABLE

Braodband modem

ETHERNET STATUS USB

WGRMbps Wireless Router

R G E A N E T

Notebook PCs with FA511 network card

Broadband Cable Modem

10 Mbps
FS608 8-port Fast Ethernet Switch
WGEMbps Wireless Ethernet Bridge Desktop PCs with FA311 network card 100 Mbps Printer with PS101 print server Macintosh computers with built in Ethernet port
Technical Specifications Network Protocol and Standards Capability: - IEEE 802.3i 10BASE-T - IEEE 802.3u 100BASE-TX - IEEE 802.3x Flow Control - Compatible with Windows, Mac OS, NetWare, Linux Interface: - RJ-45 connector for 10BASE-T and 100BASE-TX - All ports have Auto Uplink (Auto MDI-X) Power Consumption: - 7.5 W maximum Physical Specifications: - Dimensions: 158.37 x 89.75 x 34.42 mm (6.24 x 3.53 x 1.36 in) - Weight: 0.61 lb (0.28 kg) Status Lights: - Power light; speed and activity light on each port Environmental Specifications: - Operating Temperature: 0 to 40C (32 to 104F) - Operating Relative Humidity: 10-90%, non-condensing
4500 Great America Parkway Santa Clara, CA 95054 USA Phone: 1-888-NETGEAR E-mail: info@NETGEAR.com www.NETGEAR.com
Electromagnetic Emissions: - CE mark, commercial - FCC Part 15, Class B - EN (CISPR 22), Class B - C-Tick - EN - TUV (EN 60950) Warranty: - NETGEAR 3-year warranty System Requirements - Category 5 UTP Ethernet cables - Network card for each computer - Network software such as Windows, Macintosh, or Linux Package Contents - 8-port Fast Ethernet Switch FS608 - AC power adapter - Installation Guide - Warranty/support information card NETGEAR Related Products - FA311 10/100 Mbps PCI Ethernet Network Card - FA511 10/100 Mbps CardBus Notebook PC Card - FA120 10/100 Mbps USB 2.0 Fast Ethernet Adapter - RP614 4-port 10/100 Mbps Router - XE102 Wall-plugged Ethernet Bridge (U.S. only) - PS101 1-port Mini Print Server - WGEMbps Wireless Ethernet Bridge
2003 NETGEAR, Inc. NETGEAR, the Netgear Logo, the Gear Guy, and Everybodys connecting are trademarks or registered trademark of Netgear, Inc. in the United States and/or other countries. Microsoft, Windows, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved. * Free basic installation support provided for 90 days from date of purchase; optional premium support available.

Performance Specifications: - Frame filter and forward rates: 14,800 frames/sec max for 10M port 148,800 frames/sec max for 100M port Non-blocking, wire-speed frame forward rate - Forwarding modes: Store-and-forward - Network latency: <20s microseconds for 64-byte frames for 100 Mbps to 100 Mbps transmission - Address database size: 1,024 media access control (MAC) addresses - Addressing: 48-bit MAC address - Queue buffer: 128 kilobytes - Maximum cable length: 328 feet (100 M)

D-FS608v2-1