TRIAX MOBIUS TRIAX SPEED 100 TRIAX SPEED 50 TRIAX SPEED 10

+/_ to change value

Continue to Next Setting
Select 12 or 24 Hour Clock
Select Day or Month Display
In TIME mode you can set time and calendar information within two time zones. You can set two time alarms in TIME mode. The time alarm will sound for 20 seconds. Power Save: Display shuts off to conserve battery life. Press any button to turn watch ON
NOTE: The TRIAX SPEED 10 has one time zone and one alarm
BEGIN setting Time and Date
Turn Button Chime ON / OFF

Adjust Screen Contrast

Electrolite ON

Switch Time Zones

EXIT Time and Date
TIME Warp: Hold for 1 second in any mode to return to TIME mode
Scroll to TIME mode to set Alarms
Alarm ON / OFF BEGIN by pressing VIEW button to select Alarm 1 or Alarm 2
Adjusted Alarms turn ON upon EXIT
RUN mode can be used to capture lap and total time data down to 1/ 100th of a second. The convertible display can be easily switched between total time, lap time or both simultaneously during a workout. NOTE: The TRIAX SPEED 10 does not have a convertible display
VIEW button changes the convertible display to total time, lap time or both simultaneously Mark LAP 2 ( Lap flashes for 2 sec onds) START Run Mark LAP 1 ( Lap flashes for 2 sec onds)

STOP Run

Run saved to DATA mode

RESET Run

NOTE: The TRIAX SPEED 10 has a one run memory. Run is automatically stored to DATA mode.

CHRONOGRAPH LIMITS

TRIAX MOBIUS / TRIAX SPEED 100 19:59' 59" 99 (auto stops) 30 Run memory 100 Laps TRIAX SPEED 50 19:59' 59" 99 (auto stops) 10 Run memory 50 Laps TRIAX SPEED 10 19:59' 59" 99 (auto stops) 1 Run memory 10 Laps

H20 RESIST

ATTENION: Water damage may occur if the buttons are pressed underwater

MATERIAL SPECIFICATIONS

CRYSTAL Mineral Glass STRAP Polyurethane CASE Polycarbonate CASEBACK Stainless Steel BEZEL Stainless Steel BUTTONS Polycarbonate BUCKLE Stainless Steel

OPERATING TEMPERATURE

-5 to 50 Celsius
RUN mode has a PACE function which compares actual lap and total times to preset PACE target times NOTE: The TRIAX SPEED 10 does not have the PACE function

EXIT back to RUN mode

Turn PACE targets ON / OFF
Turn PACE ALARM ON / OFF The PACE ALARM will give 5 short beeps before the end of each target segment

Set Segment 1

_ Seconds, Minutes and Hours
Lap and total target time differentials display for 2 seconds Mark LAP 2 Mark LAP 1

START Run

View PACE target times before starting workout

CLEAR ALL PACE segments

In INTERVAL mode you can set five repeating segments for customized interval training. NOTE: The TRIAX SPEED 10 does not have INTR mode
Set Segment 1 _ Seconds, Minutes and Hours ( 19:59' 59" maximum )

Set up to 5 segments

START interval workout. Segment begins to countdown
This example demonstrates a 7'30" run and 1'15" walk repeating workout Press STOP to pause workout.

Press START to continue workout.

99 segment loop maximum

CLEAR ALL Segments

RESET ALL Segments

In DATA mode you can review workout data saved from RUN mode

Select RUN

DATA mode records Total Time, All Lap Times, Best Lap and Average Lap
DATA mode with the PACE targets turned ON

CLEAR ALL Runs

CLEAR Selected Run

Triax CV10 Battery

WARNING! Keep watch batteries away from children. If swallowed, contact a doctor immediately. WARNING! Batteries contain chemical substances. They should be disposed of properly according to local regulations.
Battery Type: CR2032 3V Lithium Battery Life: The battery is estimated to last 1.5 years depending on frequency and use of certain features. Activating the Electrolite feature will contribute to battery drain. Utilizing the Power Save function will help conserve battery life. Battery Replacement: Follow steps below to replace your watch battery. For best results, you can have Nikes authorized service center change the watch batter
Using a coin, unscrew the battery hatch on the watch by turning counter-clockwise. Twist and remove battery holder cover. Remove old battery. Insert a CR2032, 3V lithium battery with the writing facing you. Do not touch the 2 contacts. Replace the battery holder cover and battery hatch.

HR Transmitter

Battery Type: CR2032 3V Lithium Battery Replacement: Follow steps below to replace your HRM transmitter battery.
Using a coin, unscrew the battery hatch by turning it counter-clockwise.
Insert a CR2032 3V lithium battery with the writing facing you. Do not touch the 2 contacts.

Replace the battery lid.

SDM Pod
Battery Type: AAA Alkaline battery Battery Replacement: Follow steps below to replace your SDM pod battery.
Using a coin, turn the battery hatch 90 degrees clockwise. Insert a AAA Alkaline battery with the negative node facing you. Replace the battery hatch with care not to damage the rubber O ring.