JBL ON AIR

CONTROL 2.4G

OWNERS GUIDE

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. (Example use only shielded interface cables when connecting to computer or peripheral devices.) FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Declaration of Conformity
declare in own responsibility that the product described in this owners manual is in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001
We, Harman Consumer Group International 2, route de Tours 72500 Chteau du Loir France
declare in own responsibility that the product described in this owners manual is in compliance with technical standards: EN EN EN EN EN EN EN EN 55013:2001+A1:2003 55020:2002+A1:2003 61000-3-2:2000 61000-3-3:1995+A1:2001 60065:2002 301489-1 V 1.6.1:2005 301489-17 V 1.2.1:V 1.6.1:2004
Laurent Rault Harman Consumer Group International Chteau du Loir, France 2/07
READ FIRST! Important Safety Precautions!
13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Do not use attachments not recommended by the product manufacturer, as they may cause hazards. 16. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. 17. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 18. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 19. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock. 20. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts, which could result in a fire or electric shock. Never spill liquid of any kind on the product. 21. The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus. 22. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 23. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 24. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 25. The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Figure A. Example of Antenna Grounding as per National Electrical Code ANSI/NFPA 70
THANK YOU FOR CHOOSING JBL
For more than 60 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. Were confident that the JBL system you have chosen will provide every note of enjoyment that you expected and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL. Please take a moment to register your product on our Web site at www.jbl.com. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations.

MUTE INPUT VOL

Remote Control
The JBL On Air Control 2.4G is an advanced wireless loudspeaker system that allows you to enjoy your favorite music in remote locations around your home, or to add surround speakers to your home theater system without running wires to the back of the room. To ensure trouble-free performance, please carefully read these instructions completely before connecting or using the system.

ID CODE 3 4

UNPACKING THE SYSTEM ID

TO RIGHT SPEAKER

Carefully unpack the system. If you suspect damage from transit, report it R INPUT L immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Open the package and verify the following contents:

DC 20V SUB-OUT LINE-IN

Left/Active Speaker (Rear)

LEFT-CHANNEL SPEAKER

Included

1 x Transmitter module

1 x Universal power supply for transmitter
1 x 120V 2-Prong AC power cord for transmitter power supply 1 x 230V 2-Prong AC power cord for transmitter power supply 1 x Wall-mount bracket for transmitter with 2 x panhead M3 x 4 machine screws for attaching wall-mount bracket to transmitter + 4 x Small round self-adhesive feet to be attached on transmitter left CODE side panel if transmitter to be used vertically 1 x Active speaker/receiver (left-channel speaker) TO RIGHT SPEAKER 1 x Universal power supply for active speaker/receiver 1 x 120V 3-Prong AC power cord for active speaker/receiver power supply DC 20V SUB-OUT LINE-IN 1 x 230V 3-Prong AC power cord for active speaker/receiver power supply 1 x Wall-mount holder for active speaker/receiver universal power LEFT-CHANNEL SPEAKER supply 1 x Passive speaker (right-channel speaker) 2 x Wall-mount rotatable brackets for active and passive speakers 7 (includes bar wrench and backup cords) 1 x Remote control 1 x Interconnect cable (1m/3.3 ft. RCA RCA) 1 x Interconnect cable (1m/3.3 ft. RCA 1/8-inch mini plug) 10m/33 ft. x Speaker wire 1 x Owners manual (multilanguage) 1 x USA warranty sheet

Wireless Transmitter

TO LEFT SPEAKER

RIGHT-CHANNEL SPEAKER

Right/Passive Speaker

R INPUT L

CONNECTIONS
NOTES: For the sake of simplicity, throughout this manual we have used the term source when describing connections and operation. This would apply to any device such as an A/V receiver, audio component, computer or portable music player. The JBL On Air Control 2.4G is designed for use in most countries worldwide, depending upon local regulations. It includes 120V 230V, 50/60Hz universal power supplies for the transmitter module and the active speaker. While we have included the two most commonly used AC cords with this product, your AC electrical outlet may require the use of a different AC cord. For your safety, it is essential to use an AC cord that is fully compatible with your local electrical system. When in doubt, please consult your local JBL dealer or distributor. The JBL On Air Control 2.4G may be connected to your source in several ways. First, determine how you would like to use the JBL On Air Control 2.4G; then follow the setup instructions for that application. Application 1 Adding surround speakers to a home theater system. Continue reading the instructions for Application 1 below.

Step 2. Determine the location of the surround speakers.

Subwoofer

Left Front Channel

Center Channel

Right Front Channel
Application 2 Adding speakers to remote locations around your home. Application 1 Adding surround speakers to a home theater system: Determine if your source contains preamp outputs for rear/surround channels, usually indicated by RCA-type jacks on the back of the receiver labeled as surround preout (please refer to your sources owners manual to confirm whether it includes the preamp outputs). If your receiver includes these outputs, follow the steps below. If not, connection is not recommended. NOTE: Make sure power is turned off on all components. Step 1. Connect the interconnect cable (included) to the left and right surround/rear preamp outputs on the back of your source and the input on the transmitter module D, as shown in Figure 1.
Left Front Channel Right Surround Channel Subwoofer Right Front Channel
Left Surround Channel Left Rear Channel Center Rear Channel Right Rear Channel Right Surround Channel
RECEIVER/PROCESSOR Surround Channel Preamp Outputs

Left Surround Channel

Figure 2. Place the active (left) speaker in the recommended location for the

left surround speaker.

Figure 1.
Step 3. Connect the speaker wire (included) to the push terminals on the active speaker 5 and the push terminals on the rear of the passive speaker 9. See Figure 3. Please note that the speaker wire supplied features a polarity stripe to help distinguish its two conductors. Use this polarity stripe to ensure that you are connecting the positive (+) terminal on one speaker to the positive (+) terminal on the other, and the negative () to the negative (). It does not matter whether you use the striped conductor for connecting the positive (+) terminals or the negative () terminals.
Some computer sound cards feature preamp outputs in addition to or instead of speaker outputs. If your computer does feature preamp outputs, we recommend that they be used instead of speaker outputs. If you would like to connect the computer to the JBL On Air Control 2.4G using preamp outputs on your computer, follow the steps in Connection A. Connection Option A Connecting using the preamp outputs on your source: NOTE: Make sure power is turned off on all components. Step 1. Connect the interconnect cable (included) to the left and right front/main preamp outputs or zone 2 outputs or REC outputs and the inputs on the transmitter module D, as shown in Figure 4.
SOURCE Front/Main/Second Room Preamp Outputs

DC 20V SUB OUT LINE IN

LEFT CHANNEL SPEAKER

RIGHT CHANNEL SPEAKER

Figure 3.
Step 4. Plug the transmitter module B and active speaker 6 into the wall outlet, using the correct power supply and power cord. Make sure the transmitters antenna A is extended upwards. Step 5. If necessary, configure your source to activate the preamp level outputs for the surround/rear channels (consult your sources owners manual for specific instructions). Make sure the ID code setting on the transmitter C is set to the same setting as that on the active speaker 4. See page 8 of this manual for more information on ID codes. When connected properly, the top LED on the front of the active speaker should be green. When first plugged in, it will sometimes take several seconds for the Control 2.4G active speaker to initialize and wake up. Until then, the top LED will be in red. Once the top LED is green, the bottom LED should flash green until the transmitter and active speaker lock in. It will then also light in solid green. This LED will light in orange if the local input on the active speaker is selected (see page 8 under Local Input for more details). Application 2 Adding speakers to remote locations around your home: Audio sources that can be used in this application may be an A/V receiver or audio receiver, a portable audio player, or a computer featuring a sound card. First, determine whether your source contains RCA-type preamp outputs for the front/main channels or a 1/8-inch stereo single-pin output. On an A/V or audio receiver, the preamp outputs are usually indicated by RCA-type jacks on the back of the receiver labeled as pre-out (please refer to your sources owners manual to confirm whether it includes preamp outputs). If your source includes these RCA-type outputs, follow the steps in Connection Option A. If your source features a 1/8-inch single-pin stereo jack, follow steps in Connection Option B. If your receiver does not feature either type of preamp outputs for the front/main channels, it cannot be used with Control 2.4G. Some computer sound cards feature more than one 1/8-inch single-pin jack. There is almost always one output that is called a speaker output. However, some sound cards feature a preamp output or line output in addition to or instead of speaker outputs. If your computer does feature preamp or line outputs, we recommend that they be used instead of speaker outputs.

ID CODE 1234

Figure 4.
Step 2. Place the active speaker in the desired location in your home near an AC outlet, as it needs to plug in to the wall. Step 3. Connect the speaker wire (included) to the push terminals on the active speaker 5 and the push terminals on the rear of the passive speaker 9, as shown in Figure 3. Please note that the speaker wire supplied features a polarity stripe to help distinguish its two conductors. Use this polarity stripe to ensure that you are connecting the positive (+) terminal on one speaker to the positive (+) terminal on the other, and the negative () to the negative (). It does not matter whether you use the striped conductor for connecting the positive (+) terminals or the negative () terminals. Step 4. Plug the transmitter module B and active speaker 6 into the wall outlet, using the correct power supply and power cord. Make sure the transmitters antenna A is extended upwards. Step 5. Make sure the ID code setting on the transmitter C is set to the same setting as that on the active speaker 4. See page 8 of this manual for more information on ID codes. If necessary, configure your receiver to activate the preamp level outputs for the main/front channels (consult your sources owners manual for specific instructions).
When connected properly, the top LED on the front of the active speaker should be green. When first plugged in, it will sometimes take several seconds for the Control 2.4G active speaker to initialize and wake up. Until then, the top LED will be in red. Once the top LED is green, the bottom LED should flash green until the transmitter and active speaker lock in. It will then also light in solid green. This LED will light in orange if the local input on the active speaker is selected (see page 8 under Local Input for more details). Connection Option B Connecting using the 1/8-inch single-pin stereo jack on your source: NOTE: Make sure power is turned off on all components. Step 1. Connect the RCA 1/8-inch mini-jack cable (included) to the preamp out, line out or headphone output of your portable audio player and the inputs on the transmitter module D, as shown in Figure 5.
Portable Audio Device or Computer Headphone Jack (1/8") Mini
Step 4. Plug the transmitter module B and active speaker 6 into the wall outlet, using the correct power supply and power cord. Make sure the transmitters antenna A is extended upward. Make sure the ID code setting on the transmitter C is set to the same setting as that on the active speaker 4. See page 8 of this manual for more information on ID codes. When connected properly, the top LED on the front of the active speaker should be green. When first plugged in, it will sometimes take several seconds for the Control 2.4G active speaker to initialize and wake up. Until then the top LED will be in red. Once the top LED is green, the bottom LED should flash green until the transmitter and active speaker lock in. It will then also light in solid green. This LED will light in orange if the local input on the active speaker is selected (see page 8 under Local Input for more details).

Figure 5.

Step 2. Place the active speaker in the desired location in your home near an AC outlet, as it needs to plug into the wall. Step 3. Connect the speaker wire (included) to the push terminals on the active speaker 5 and the push terminals on the rear of the passive speaker 9, as shown in Figure 3. Please note that the speaker wire supplied features a polarity stripe to help distinguish its two conductors. Use this polarity stripe to ensure that you are connecting the positive (+) terminal on one speaker to the positive (+) terminal on the other, and the negative () to the negative (). It does not matter whether you use the striped conductor for connecting the positive (+) terminals or the negative () terminals.

OPERATION

Adjusting the Volume
Application 1 Adding surround speakers to a home theater system: In this application, the output level of your Control 2.4G active speakers will not only be dependent on the volume setting of your A/V source; it will also need to be properly adjusted after installation and before use in order to be able to work correctly with the other speakers in your multichannel surround system. To adjust the output level, turn your A/V source on, set your A/V sources volume control about a third of the way up, and activate the speaker-level-adjustment test tone. Make sure that the Control 2.4G transmitter and speakers are on, both of its speakers are connected, and there is RF lock (i.e., lower LED on active speaker is solid green). Using the Control 2.4G remote control 1 and 2 adjust the volume level of Control 2.4G until its output level is balanced with the rest of the speakers in your surround system. From this point on, you will not be using the remote control of your Control 2.4G for volume settings. You will be increasing and decreasing the output level for the entire surround sound system using your A/V sources volume control. Please note that Control 2.4G will retain its volume setting when it is in standby, so there is no need to set its volume level every time the system is turned on. Application 2 Adding speakers to remote locations around your home: Depending on the type of connection and the specific source that you are using, the volume setting on your receiver may affect the sound output level of your Control 2.4G. To check whether the output from your source is volumedependent, turn the volume level on your receiver to approximately half-way. Turn on your Control 2.4G transmitter and active speaker. Once the lower LED on the active speaker lights in solid green, indicating that RF lock has been achieved, verify that there is sound output from the active speaker. Then increase and decrease the volume control on your receiver and observe whether this affects the sound output from your active speakers. If it does not, then the volume control on your source unit can be set at any position that you may desire, as it does not affect the performance of Control 2.4G. If changing the volume setting on your source does affect the output from Control 2.4G, then you will need to always keep your sources volume control at about half-way up with audio receivers or A/V receivers, at about three-quarters of the way up when using a computer, and at maximum if using a portable audio device. From this point on, you will use the remote control included with the JBL On Air Control 2.4G wireless speaker system to adjust volume 1 and 2. Orange

ID Codes

In the unlikely event that you experience interference when operating the system, or if you have more than one set of Control 2.4G transmitters and receivers in operation, you may change the channel in which the system operates. On the transmitter module and the active speaker, there is a fourposition ID Code selector. Simply set the selectors to one of the other positions. The transmitter and active speaker must be set to the same position in order for the system to function correctly. You can also set up a maximum of two pairs of speakers to be receiving from the same transmitter by setting the channel selector on the transmitter and both of the active speakers to the same channel. Please note that the two active speakers need to be at least 10m (33 feet) apart, or reception and operating range in one or both units may be degraded.
Indicator Light Information
Power Indicator LED (Top) Green System is on Input LED (Bottom) Transmitter and speaker are communicating (RF lock) Transmitter and speaker are not communicating (no RF lock)
Blinking Green Receiving IR command from remote control Red Standby (no signal being received)

Local input is selected

Subwoofer Output The JBL On Air Control 2.4G wireless speaker system includes a subwoofer output 7 on the rear of the active speaker. This output allows you to feed the low-frequency sounds to a separate powered subwoofer. A powered subwoofer will deliver deeper bass response than is possible with speakers alone. To connect a powered subwoofer to the active speaker, simply connect the subout 7 on the active speaker to the line-in on the rear of the powered subwoofer using a 1/8-inch stereo mini-jack/dual-RCA cable (not included*). Please note that this output is full-range and not filtered or low-passed. Make sure that your powered subwoofer features a low-pass crossover network and that this crossover is indeed selected. Do not use the LFE input on a powered subwoofer as it is not filtered and you will be hearing a lot of undesirable higher frequency information from your subwoofer. * Only one stereo mini-jack/dual-RCA cable is included with the system. If you are following Application 2, Connection Option B, you will need to purchase this additional cable.

Local Input

The JBL On Air Control 2.4G wireless speaker system also includes a local input 8 on the rear of the active speaker. This input allows you to hook up a portable audio player directly to the speaker wherever you may happen to be. For example, you could have the system connected to your receiver as described in Application 2, listening to a local FM station and then hook up your portable music player to the local input and switch between the two different sources. To connect a portable audio player to the active speaker, simply connect the preamp out, line out or headphone jack to the line-in 8 on the rear of the active speaker using a 1/8-inch mini-jack 1/8-inch mini-jack cable (not included). To switch between the two sources, push the input button 3 on the remote control.
A Word About Wireless Products
The JBL On Air Control 2.4G wireless speaker system utilizes advanced wireless transceivers operating in the 2.4GHz frequency band. This is the same frequency band that is used for wireless home networks and high-quality cordless phones. It also allows for the transmission of high-performance, full-spectrum sound to remote locations, wirelessly. Like all wireless devices, the JBL On Air Control 2.4G wireless speakers operating range may vary depending upon variables such as building construction methods and materials, atmospheric conditions and other sources of interference. Please consult your JBL dealer or distributor, or visit us at www.jbl.com for further information or assistance.

WALL AND STAND PLACEMENT

Adjustable wall brackets are included for the two speakers and transmitter module. The included brackets are for wall-mounting only. It is not to be used for ceiling mounting. Ceiling mounting of the Control 2.4G transmitter and/or speakers is not recommended, regardless of bracket used. A. Loosen and remove the molded nut (2) by turning it counterclockwise. Use the supplied metal bar (5) if necessary by inserting it in one of the holes on the molded nut (2). B. Pull the ball/shaft (3) out of the wall bracket (4).
Wall-Mounting the Speakers Using Wall Brackets Provided
Important Safety Note: Proper selection of mounting hardware not included herein, and proper assembly and installation of brackets, including, but not limited to, selection of appropriate weight-bearing support and bracket use with the specified speaker only is the exclusive responsibility of the customer. Manufacturer disclaims any liability for the selection of mounting hardware and/or bracket installation.

C. Slide the molded nut (2) onto the ball/shaft (3) with threaded opening facing the ball, and thread on the metal nut (1) all the way onto the ball/shaft (3), with the nuts (1) knurled surface facing away from the ball. D. Screw the ball/shaft (3) into the threaded 1/4"-20 insert on the back of the speaker cabinet (6) until it is fully seated against the bottom of the insert. Back out the ball-shaft assembly 1/2 of a turn and tighten the nut against the speaker. If the ball and shaft assembly is not backed out before tightening the nut, performing Step G below may dislodge the threaded insert in the speaker housing and permanently damage the speaker. E. Tighten the knurled nut (1) using a crescent wrench until it is firmly seated against the back of the speaker and has fully locked the ball/shaft (3) and the speaker cabinet together. Please note that once this nut is tightened, it may embed some marks on the back of the speaker where the attachment is made. However, these marks will be covered by the nut (1). F. The backup cord (8) is provided as an additional measure to prevent the fall of the speaker in case the speaker becomes detached from the wall bracket. One of the two lower screws (9) that attach the wall bracket (4) to the wall will need to go through the eyelet (11) at the end of the cord before going through the wall-bracket hole. Mount the wall bracket (4) onto a wood stud on the wall, using #10, minimum 1-inch-long, panhead wood screws. Make sure that all four screws are driven into the stud, not drywall. If the bracket needs to be mounted on drywall, the use of properly selected and installed wall anchors and screws is essential. Make sure that the screw head is at least 0.36 of an inch (approximately 3/8 of an inch) or larger in diameter so that it can properly hold the backup cord eyelet (11). G. Holding the speaker cabinet (7) with both hands, reinsert the ball portion of the ball/shaft (3) into the wall bracket (4). H. Hand-tighten the molded nut (2) while positioning the speaker for the intended orientation. I. Once the orientation of the speaker is finalized, use the metal bar (5) in one of the holes on the molded nut (2) and tighten securely. J. Securely attach the other end (10) of the backup cord (8) to the Control 2.4G by engaging it through the bar (12) on the back speaker. Also included with the system is a wall-mount holder for the active speakers power supply. If desired, you may attach this holder to the wall and insert the speakers power supply.

CORRECT

INCORRECT
Wall-Mounting the Speakers Using Third-Party Wall Brackets
Each JBL On Air Control 2.4G wireless speaker contains a 1/4"-20 threaded insert on the back to facilitate the use of third-party wall brackets. Please consult your JBL dealer or distributor for recommendations. NOTES: Customer is responsible for proper selection and installation of appropriate third-party wall brackets. The threaded insert on the bottom of the speaker is not intended for wall-bracket attachment. It is provided for use with an appropriate third-party floor stand.
Stand-Mounting the Speakers
Each JBL On Air Control 2.4G wireless speaker contains a 1/4"-20 threaded insert on the bottom to facilitate the use of third-party floor stands. Please consult your JBL dealer for recommendations. NOTE: Customer is responsible for proper selection and installation of appropriate third-party wall brackets and/or floor stands.
Wall-Mounting the Transmitter Module
Step 1. Insert the two M3 x 4 machine screws through the wall bracket and into the rear of the transmitter module, as shown in Figure 6.

Figure 6.

Step 2. Attach the transmitter module with wall bracket to the wall using suitable hardware, and wall anchors if necessary.

MAINTENANCE AND SERVICE

The speaker and transmitter enclosures may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the minimum. In the event that your system ever needs service, contact your local JBL dealer or distributor, or visit www.jbl.com for a service center near you.

SPECIFICATIONS

Frequency Range (3dB): Amplifier Output: Low-Frequency Driver: High-Frequency Driver: Operating Range: RF Operating Frequency: 50Hz 20kHz 15 Watts per channel 4" (100mm) Magnetically shielded 1/2" (12mm) Titanium-laminate, magnetically shielded Up to 70' (21m) depending upon conditions 2.4GHz
Dimensions Speaker (H x W x D): Transmitter (H x W x D): 9" x 6-1/8" x 5-1/2" (229mm x 156mm x 140mm) 1-1/8" x 4-7/8" x 3-7/8" (29mm x 124mm x 98mm) 3-3/4" (95mm) High with antenna extended Weight Active Speaker: Passive Speaker: Transmitter: 4.6 lb (2.1kg) 4.3 lb (2.0kg) 0.5 lb (0.2kg)

Features, specifications and appearance are subject to change without notice.
JBL and Control Series are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Pro Sound Comes Home is a trademark of Harman International Industries, Incorporated.

PRO SOUND COMES HOME

Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA 8500 Balboa Boulevard, Northridge, CA 91329 USA 516.255.4JBL (4525) (USA only) www.jbl.com 2007 Harman International Industries, Incorporated. All rights reserved. Part No. 406-000-05529-E