Lifestyle LP522 Electronic Programmer
The LP522 is a 5 day/2 day programmer which allows, with the appropriate system, seperate time control of central heating and hot water at different times on weekdays and weekends.
A wall-plate with wiring terminals is provided, however, the LP522 will plug directly onto existing wallplates of some popular programmers without any rewiring.
Make Invensys ACL Model Lifestyle LPMP FP Honeywell Horstmann ST699B Ameythyst 7 & 10 Coral Diadem/Electronic Diamond Gem Leucite EP2000/102 3060/3020P F1, F9 & F414 M5 DHP2201 ET1401/1451 Centroller & 600 805, 900, 9000, 9001 Microtimer T2002 T2000 & T2003 E E E E E E E E E E E E E E E E E E N N N N N N N 7 N N N N N N N N L L L L L L L 6 L L L L L L L L

Installation

ROOM THERMOSTAT
Mid-Position Valve System PROGRAMMER N L SET TO P
Use existing wall-plate when replacing: Potterton Miniminder, Glow-worm Master-Mind, any Landis & Staefa programmer, or ACL Lifestyle LS522. Use new LP522 wall-plate when replacing others consult table below for terminal reference comparisons.
MAKE SURE MAINS INPUT HAS A 3 AMP FUSE
Installation should be carried out by a qualified electrician or heating engineer. Using EXISTING WALL-PLATE Switch off mains. Loosen the securing screws on the old programmer and unplug it. Check that there is 70mm clearance to the right of the wall-plate and 25mm above it. Plug the LP522 onto the wall-plate. Re-tighten securing screws. Check fuse (3A) and switch on mains. Set timing and programme as detailed in the User guide. Fitting NEW WALL-PLATE provided Position the wall-plate with 70mm clearance to its right, 25mm above and access to the securing screws underneath. Ensure that the supporting surface will fully cover the back of the programmer. The ideal location is 1.4M above floor level, accessible, reasonably lit and free from condensation or extremes of temperature.

WALLPLATE CLOCK

Fix the wall-plate, terminals at the top, either direct to a flat wall using wall plugs and No. 6 x 1 woodscrews or on a flush mounting single conduit box type UA1 (BS4662) using M3.5 x 14 screws. DO NOT use a surface mounting box. Ensure the mains supply is switched off then make wiring connections as shown in this leaflet. For surface wiring, use pliers to snap out the removable cable entry strip on the bottom edge of the wall-plate. The LP522 is double insulated and needs no earth connection but an earthing continuity (loop) terminal is provided for convenience After wiring, Plug in the LP522 and tighten the securing screws. Check the fuse (3A) and switch on the mains. Set timing and programme as detailed in the User Guide. Switch off mains before removing programmer from wall-plate. NEVER FIT THE PROGRAMMER TO A LIVE WALL- PLATE. Connection Charts Arrowed numbers relate to the junction box. Consult boiler handbook for details of pump overrun wiring. Wiring colour codes: GR Y BK BL BR Grey Yellow Black Blue Brown RD W OR YG Red White Orange Yellow/Green
RTS 1&2 RTS 4,5&6 ETS 1

E L N N L N 4 E

C L 1 1
CYLINDER THERMOSTAT * SCH HTS C 1
# - LINK L-1 FOR 230V OUTPUT

JUNCTION BOX

1112 LNE
Terminals 1 HW Off 2 CH Off 3 HW On HW HW On 4 CH On CH CH On

L N E 3

E N L PUMP
Switched and Fused (3A) Mains input

GR OR BL YG

MID-POSITION VALVE LIFESTYLE 679H340-30L0 (22mm) LIFESTYLE 779H340-30L0 (28mm) DRAYTON FLOWSHARE 2 Honeywell V4073A Landis & Gyr MAV 3
For pump overrun boilers consult manufacturers instructions * See Thermostat Key

BOILER

Potterton Danfoss Randall
Spring-Return 2-Valve System ROOM THERMOSTAT E L N C H RTS 1&2 N L 3 RTS 4,5&6 L N # ETS E PROGRAMMER N L SET TO P CYLINDER THERMOSTAT * SCH HTS C 1

HW Off

CH Off

CH OFF

Sangamo Sunvic Smiths Switchmaster Thorn Towerchron
*Thermostat Key C H S Common Call for Heat Satisfied N E L Neutral Earth Live

3 E N L PUMP

Gravity HW, Pumped CH with Room Stat PROGRAMMER N L SET TO G 5 E N L PUMP E N L
For pump overrun boilers consult manufacturers instructions See Thermostat Key

LWC2 3

GR OR BR BL YG CH VALVE
GR OR BR BL YG DHW VALVE 7 E N L

Before Installation

Set the link on the back of the programmer to P or G according to the type of system.
P - Fully PUMPED and controlled system, allowing heating and hot water to be selected separately. G - GRAVITY fed hot water system which does not permit heating to be on without hot water. It is possible to have hot water without heating.
LIFESTYLE 679H308-30L1 LIFESTYLE 779H33530L10 DRAYTON ZV22 Honeywell V4043H1056 Landis & Gyr ZAV222

User Guide

Setting the Clock

Switch on the mains supply to the LP522 and hinge down the front cover. Press and release the button marked SET. The question SET CLOCK ? will appear in the display. Press and release the button marked YES to answer the question and the day part of the display will flash. Use the + and - buttons to change to the correct day then press SET again. This will cause the hour part of the display to flash. Again use the + or - to change to the correct hour (check AM or PM) then press SET again. The display will now show SET PROG? (see later instructions for changing your programme). Press the SET button again, and the display will show the time of day you have set. Your programmer is now in the operating mode and ready to work using the built-in standard programme times.
LPDay / 2 Day Electronic Programmer
The Lifestyle LP522 programmer will automatically switch your system ON and OFF once or twice a day, whichever you wish and at whatever times you choose. Weekend times can be different from weekday times. It has the advantage of a battery back-up system to protect the programme timings during power cuts or shut-downs. If you have a fully-pumped and controlled system you will be able to have central heating without hotwater or vice versa. A gravity-fed hot water system does not allow heating to be on without hot water.
NOTE: If you wish to make changes to the ON or OFF timings for CH during Monday-Friday press the YES button, if not press the SET button again and this will change the display question to SET HW MONFRI PROG ?. Press YES if you want to change the HW timings during Monday-Friday, if not press SET again. The display will now ask SET CH SATSUN PROG ?. Press YES to make changes or SET to move to SET HW SATSUN PROG ?. Again you have to answer the question either with the YES button or by pressing the SET button once more which will return the programmer to the normal operating mode with the time of day displayed. If you answer YES to SET CH MONFRI PROG ? or to SET HW MONFRI PROG ? the display will show the time set for the first switch on (ON1) to occur during Monday - Friday. This can be altered in steps of 10

minutes by the use of the + and - buttons. When the display is showing the time you want, press SET and the OFF1 time will be seen. Again changes may be made with the + or - buttons before pressing SET to display the time for ON2 to occur. After making any adjustments press SET again to get the OFF2 time displayed. This may be adjusted up to 23 hours 50 mins after the first switch on time. Press SET again and SET CH SATSUN PROG ? is displayed. By answering YES, the same procedure can be followed for adjusting the CH timings for Saturday and Sunday. Press SET again and SET HW SATSUN PROG ? is displayed. By answering YES, the same procedure can be followed for adjusting the HW timings before pressing SET one final time to go back into operating mode.

Programme Options

Your installer should have set the LP522 to suit your heating system. If this is one which does not permit you to have CH without HW you will find the LP522 does not allow this to happen. If you have a fully pumped and controlled system then you will be able to operate heating and hot water independently. The LP522 gives you 4 options for both CH and HW: OFF - Off all the time TWICE - On for two periods each day ONCE - On for one period each day (ON1 OFF2) ON - On all the time. Remember some hot water systems do not allow CH to be ON without HW being ON. Obtain the options you require by using the SELECT buttons to move the arrows in the display to the appropriate positions. Your programmer is now working using the standard programme times. If these suit your needs there is nothing else to do. You can temporarily override the normal switching times by pushing the button marked ADVANCE. This switches ON to OFF or OFF to ON as you require, but the normal programme switching times will not be permanently affected. If you want to make changes to the programme (10 minutes steps) it is suggested you write them down before making the changes.

SAT-SUN PROGRAMME HW CH

Technical Data
Type: LP522 Programmer Voltage: 230V AC +10% -15% 50Hz Rating: 2 (1) A 230V AC each switch Ambient Temp: 0C to 45C Operating - 20C to 50C Storage Battery Reserve: Display - typically 1 hour Timekeeping - 7 to 8 hours Programme - Min 1 1/ 2 Years Programming Resolution: 10 minutes Wiring: Designed for fixed wiring only to comply with current I.E.E. regulations

Helpful Hints

1. The + and - buttons are used to change times. Press and release for small changes; press and hold down and the time will run. 2. You cannot set the first switch on time (ON1) before mid-night but you can set the OFF2 after mid-night so long as you dont try to exceed 23 hours 50 mins after ON1. 3. The four switching times have to be in sequence (ON 1, OFF1, ON2, OFF2) if you try to set OFF1 earlier than ON 1 the display will stop at the ON1 time with the OFF symbol flashing. The same thing will happen with other switching times e.g. between OFF1 and ON2, this time the ON symbol will flash. 4. If you attempt to set the ON1 time after the OFF1 time, the ON symbol will flash and the OFF1 setting will follow the ON1 time being set to prevent incorrect programming. The same feature applies with the ON2 and OFF2 times and also between the OFF1 and ON2 times. 5. If you get confused and wish to start the whole programming procedure again, press the SET and + buttons together for a moment. The programmer will revert to a mid-night time display and the built-in standard programme. You will now have to set the clock again and then enter the programme you want. 6. When you are making adjustments to timings, if no button is pressed for 1 to 2 minutes, the programmer will automatically revert to the normal operating mode. 7. To shut the CH down for the summer simply select the OFF option by means of the CH select button. 090 - 653 ISSUE C 08/01
SWITCHING ON1 - Start of first ON period of day

MON-FRI PROGRAMME HW CH

6.30 am 8.30 am 4.30 pm 10.30 pm
7.00 am 9.00 am 4.00 pm 11.00 pm
Maintenance: No user maintenance should be attempted. Invensys Climate Controls continuously seek to improve products and reserve the right to make changes without notice.
OFF1 - End of first ON period ON2 - Start of second ON period OFF2 - Final switch off

Programming

The clock in the LP522 has to be set to the actual day of the week and time of day. It must then be told at what times you want it to switch your Central Heating (CH) and Hot Water (HW) system ON and OFF both for weekdays and weekends. The LP522 has an in-built programme of standard switching times. They may well be right for you, but if they are not exactly what you want you can change them. The standard programme is shown in the table below and for simplicity, the switching operations are described as ON1, OFF1, ON2, and OFF2 from now on.

Changing your Programme

With the programmer in the operating mode and the display showing the actual time of day, press the SET button. The display will show SET CLOCK ? but this has already been done so push the SET button again. The question SET PROG ? will appear and as it is the programme timings which are to be changed answer by pressing the YES button. The display will now ask SET CH MONFRI PROG ?.

CONFORMS TO THE ESSENTIAL REQUIREMENTS OF THE FOLLOWING DIRECTIVES: 89/336/EEC - Electromagnetic compatibility 73/23/EEC - Low voltage Directive
Invensys Climate Controls Limited Cordwallis Street, Maidenhead, Berkshire SL6 7BQ Tel: +44 (0)Sales Fax: +44 (0)Technical Helpline: +44 (0)Website: www.climate-eu.invensys.com

Programmers allow you to set On and Off time periods. Some models switch the central heating and domestic hot water on and off at the same time, while others allow the domestic hot water and heating to come on and go off at different times. Set the On and Off time periods to suit your own lifestyle. On some programmers you must also set whether you want the heating and hot water to run continuously, run under the chosen On and Off heating periods, or be permanently off. The time on the programmer must be correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean Time and British Summer Time. You may be able to temporarily adjust the heating programme, for example, Override, Advance or Boost. These are explained in the manufacturers instructions. The heating will not work if the room thermostat has switched the heating off. And, if you have a hot-water cylinder, the water heating will not work if the cylinder thermostat detects that the hot water has reached the correct temperature.

SELECT 207XL

USER INSTRUCTIONS

MO TU WE TH FR SA SU

AD ON AUTO ALLDA

SELECT CH BUTTON

ON OFF

SELECT HW

CENTRAL HEATING

TIMES RESE +

HOT WATER

INTRODUCTION

This central heating programmer can automatically switch your central heating and hot water ON and OFF, independently, up to 3 times a day, at whatever times you choose.
During installation, the installer selects 24 hour, or 5 day/2 day, or 7 day programming and 2 or 3 on/off periods per day, via a 4 position DIP switch on the back of the unit (see installation instructions). IMPORTANT: These settings should only be changed by a qualified person. Contact your installer. The 24 hour programmer option runs the same programme every day. The 5 day/2 day programmer options allows different ON/OFF times at weekends. The 7 day programmer option allows different ON/OFF times for each day of the week. The unit is designed to eliminate the possibility of accidental changes to your programme. Buttons normally visible, only affect your set programme temporarily. All buttons which can permanently change your programme are located behind the flip-down fascia. SELECTING OPERATING MODE
The Heating and Hot water mode select buttons are used to set the operating mode for CENTRAL HEATING and HOT WATER respectively. Each has 4 modes as described:ADV MO TU WE TH FR SA SU ADV

ON AUTO ALLDAY OFF

Heating mode Selection button And indicator ON AUTO ALLDAY

12 : 00

RUN ON OFF
Hot Water mode Selection button And indicator
Central heating and/or Hot water on continuously (I.E. All the time). Central heating and/or Hot water will be switched On or Off as programmed Central heating and/or Hot water will be switched On only once each day. It will switch ON at the first ON time and OFF at the last OFF time. Central heating and/or Hot water continuously OFF.
Press the SET button once. The display will flash above the clock. Press the +/- buttons to adjust the time. Hold down button to change time quicker. Press DAY button to move indicator to Current day. Press SET button repeatedly to move Indicator to RUN position. NOTE: The unit will automatically return To run mode if a period of 5 minutes passes Without any buttons being pressed.

BST/GMT TIME CHANGES

To move the time forward or back 1 hour, press and hold for 3 secs, the TIME +/- button (as appropriate), while the unit is in run mode.

CHANGING PROGRAMME TIMES

The two built in programmes, one for Central Heating and one for Hot water, can easily be changed to better suit your needs.
ADV MO TU WE TH FR SA SU ADV
To change the Central heating programme Press SET button repeatedly until the display Indicator is flashing above the radiator symbol. An indicator will appear above ON and the Number1 will show above it. This indicates the time shown on the display is the first ON time. Change this to the required time by pressing the +/- buttons. Press NEXT button to move indicator to above OFF. Time now shown is the 1st OFF time. Change as before. Use the NEXT and +/- buttons in this way to Program the second time period. If the unit is set for three ON /OFF periods, the Number 3 will appear. This is set in exactly the same way as the previous second time period.
If unit is installed as a 7 day programmer, the initial programme displayed will be for Monday. You can go to any day of the week by pressing DAY button repeatedly. The ON/OFF times can be changed for each day as above. If you press COPY button, the current programme will be copied into the next day. If unit is installed as a 5day/2day programmer, the initial programme displayed will be for Monday to Friday. Pressing DAY button will take you to the programme for Saturday and Sunday. The ON/OFF times can be changed for each day group as above. If you press COPY button, the current programme will be copied into the next day group. If the unit is installed as a 24hr. Programmer, the built in programme will be the same for each day (as for Monday to Friday). The COPY function is not required if installed as a 24 hr. programmer. To return to RUN mode, press SET button until the display indicator returns to above the RUN position. To change HOT WATER programme Press SET button repeatedly until flashing indicator on display is above the tap symbol and proceed exactly as Central heating above. Note It is not possible to copy Sunday to Monday. For convenience to allow for programmes to go past midnight, the programme day is from 03:00am to 02:50am the next day. If your programme gets scrambled, or you want to start again, press the reset button using a non-metallic tool to re-load the default programmes, then press any button to clear the DIP switch configuration code. The unit should revert to time setting mode ready for programming. USING ADVANCE This function is only available when programme is in AUTO or ALLDAY operating modes. To Advance Central Heating

Press the left hand ADV button. This will turn Central heating ON if it was in an OFF period And vice versa. It will stay in this state until either ADV is pressed again, or until a programmed ON/OFF commences. An indicator will appear on display top left hand Corner, pointing at ADV. This is normally covered By the flip down front fascia panel.
To Advance Hot Water Press the right hand ADV button. This will turn Hot Water ON if it was in an OFF period And vice versa. It will stay in this state until either ADV is pressed again, or until a programmed ON/OFF commences. An indicator will appear on display top left hand Corner, pointing at ADV. This is normally covered By the flip down front fascia panel. USING+1HR. For +1hr Central Heating Press the left hand +1hr button. If the central Heating operating mode is OFF then it will switch on for 1 hr. If the central heating operating mode is AUTO or ALLDAY, then during an OFF period, it will switch on for 1hr. If during a ON period, then it will temporarily MO TU WE TH FR SA SU ADV ADV extend that programme by 1hr. An indicator will appear on display lower left corner pointing at +1hr. This is normally covered by the flip down front fascia panel. Pressing +1hr again cancels this function. When in the ON mode the +1hr button has no effect.
ON AUTO ALLDAY OFF ADV MO TU WE TH FR SA SU ADV
USING+1HR. For +1hr Hot Water Press the right hand +1hr button. If the hot water operating mode is OFF then it will switch on for 1 hr. If the hot water operating mode is AUTO or ALLDAY, then during an OFF period, it will switch on for 1hr. If during a ON period, then it will temporarily MO TU WE TH FR SA SU ADV ADV extend that programme by 1hr. An indicator will appear on display lower right corner pointing at +1hr. This is normally covered by the flip down front fascia panel. Pressing +1hr again cancels this function. When in the ON mode the +1hr button has no effect.
POWER INTERRUPTION In the event of mains supply failure, the back up battery ensures programmer continues to keep time and retain your stored programme. The screen will go BLANK, but will return when power is restored. If left continuously without power for more than 30 days, it will stop keeping time. When power is restored, it will be necessary to reset time and day. BATTERY REPLACEMENT Replace with a 3v Lithium button cell type Cr2032. Fit into the back of the unit, observing correct polarity as marked. RESET BUTTON Press the reset button with a non-metallic pointed tool to restore the built in programme. The display will then show the current state of the configuration switches.

LINKING CENTRAL HEATING AND HOT WATER If required, it is possible to set both central heating and hot water to follow the same program. This is done by holding the COPY button down, while pressing reset. This simplifies programming as changes need only be made once, and will affect both central heating and hot water.
Configuration 2 on/2off/pumped 3 on/3off/pumped 2 on/2off/gravity 3 on/3off/gravity
Display 2 PU 3 PU 2 GA 3 GA Mon to Sun day indicators Mon to Sun successively on Mon to Fri on alternating with Sat, Sun on Mon to Sun all on together

7 day 5/2 day 24Hr

E.G. 24hr. 2 on/2off pumped, would look like this:ADV MO TU WE TH FR SA SU ADV
NOTE The last letter of the display (i.e. the U or the A) will be L, if central heating and hot water have been linked. E.G. 2 PL = 2on/2off pumped, linked CH/HW Press any button to revert to time setting mode. The unit is then ready for programming. See SETTING TIME OF DAY section. Factory programme settings Mon-Fri Sat&Sun BUILT IN PROGRAMME 1st ON 6:00am 7:00am 1st OFF 8:30am 9:00am For convenience, the programmer has a built in programme which for many people is perfectly 12:00 noon 12:00 noon 2nd ON satisfactory, but it can be changed quite easily 2nd OFF 12:00 noon 12:00 noon (see section CHANGING PROGRAMMING TIMES) 4:30pm 11:00pm 3rd ON 10:30pm 11:00pm 3rd OFF If the unit is installed as a 24 hour programmer, the built in programme will be the same for each day (as Mon. to Fri. above).
Installation Instructions SELECT207XL Programmer Select 207xl Technical Data Power supply Ambient temperature Total Input Switch Rating Battery type Battery back up Wiring Maintenance Disconnection class 230v AC 50Hz. Operating 0C to 35C 6A 230vAC 6(2)A 3v Lithium button Crdays(Time & programme) For fixed wiring only No user maintenance reqd. 1B
This unit must be installed by a competent person in accordance with the latest appropriate wiring regulations. All 3 port spring return motorised valves can remain powered ON in the CH position after the Pre Installation set-up demand for heating has been satisfied, even if the boiler and the pump are switched off. It can be left Before installing, set the bank of 4 DIP switches on all night, using twice as much energy as it on the back, to configure the unit according to the should. The valve will only return from this chart below. latched position to the HW position after a demand for HW or HW & CH together. This can gravity Pumped lead to motor burn out, and failure of any make of 3 port spring return motorised valve. 7 day The Select 207 programmer is supplied with a 24Hr patented system to prevent this latching. 5/2 day Whenever the programme stops calling for CH, it 2 on/offs 3 on/offs sends a signal to the valve to fully switch it off. This will significantly prolong the life of all makes of 3 port spring return motorised valves and save DIP switches shown in factory default position energy. The Select 207 is supplied with DEPumped Allows independent control of CH and LATCH activated. (It has no effect on 2 port valves). HW. Gravity Does not allow CH without HW, but can To de-activate the DE-LATCH, cut the link as indicated on the back of the programmer before Provide HW without CH. 24Hr. Runs same programme every day installing. 5/2 Day - Allows different ON/OFF times at INSTALLATION weekend 7 Day - Allows different on/off times every day This unit is compatible with many other programmers and may be fitted to existing standard wall plates. Please consult the WIRING Locate the back up battery, remove packing and INTERCHANGE GUIDE for compatible fit to the back of the unit, observing correct programmer types. Some are directly polarity as marked. interchangeable, others will require minor This will ensure times and programme settings changes to wiring connections. are maintained during temporary power Be sure to switch off the mains supply before interruptions. starting. Please read all installation instructions before proceeding. When unit is first switched on, or when the reset Ensure that the fixed wiring connections to the button is pressed, the status of the DIP switches mains supply, is via a fuse rated at not more is displayed. 6 amps, and a class A switch, having a contact Energy saving feature separation of a minimum of 3mm in all poles. Sunvics patented De-Latch saves energy and increases the life of 3 port spring return motorised valves.

DIRECT UPGRADE FOR EXISTING PROGRAMMERS
1.Switch off mains. Loosen 2 securing screws on old programmer and unplug it. 2.Check existing wall-plate has been correctly fitted. (See section,Fitting wall plate) 3.Plug SELECT programmer into wall-plate and re-tighten screws. Switch on at mains. 4.Press RESET button located behind the flipdown fascia panel. The status of the DIP switch settings will be displayed. Pressing any button will cause the display to go to time setting mode. 5.Set timing and programme as detailed in user guide FITTING WALL PLATE 1.Position the wall-plate (terminals along the top edge) with 60mm(Min) clearance to its right, 25mm(Min) above, 90mm(Min) below. Ensure that the supporting surface will fully cover the back of the programmer. 2.Ideal location would be 1.4m above floor level, easily accessible, reasonably lit and free from condensation or temperature extremes. 3.Fix the wall-plate to a flush mounting single conduit box type UA1(BS4662) using M3.5 x 14 bolts. 4.Ensure that the wiring to the wall-plate terminals leads directly away from the terminals and is completely enclosed within the wall-plate aperture. Wire ends must be stripped and screwed to the terminals, so that minimal bare wire is showing. 5.If the unit is fitted to a metal surface, IT IS ESSENTIAL that the metal be earthed. Do not use a surface mounting box. 6.Ensure the mains supply is switched off, then make wiring connections. No EARTH connection is required, but ensure continuity of EARTH throughout the system. 7.After wiring, plug unit into wall plate and tighten the securing screws. Switch on at mains. 8.Press RESET button located behind the flipdown fascia panel. The status of the DIP switch settings will be displayed. Pressing any button will cause the display to go to time setting mode. 9.Setting timing and programme as detailed in user guide. 10.NEVER fit or remove the unit to a LIVE wall-plate.
This product complies with the essential requirements of the following EC Directives: Electro-magnetic compatibility directive EMC 89/336/EEC (as amended by 91/263/EEC And 92/31/EEC Low Voltage directive LVD 73/23/EEC;93/68/EEC
Programmer Internal Wiring Diagram

Electronics

1 HW OFF

2 CH OFF

3 HW ON

4 CH ON

Mains Fused 6Amps
SUNVIC CONTROLS Ltd. Bellshill Road Uddingston Glasgow G71 6NP Tel Fax 01698 813637

Tech Helpline Tech Help. Fax WWW.sunvic.co.uk In the interests of continuous product improvement, Sunvic Controls reserve the right to alter designs, specifications and materials, without prior notice, and cannot accept liability for error.
Installation leaflet LE/497/0001 ISSUE 01 FEB 2003
DIRECT PLUG-IN REPLACEMENT FOR EXISTING PROGRAMMERS
Programmer will plug directly onto existing wall-plates of the following programmers without any rewiring, just follow the installation instructions. MANUFACTURER ACL MODEL LP112, LS241, LS522 LS722, LP241, LP522 LP722 FP75, FP15, CP75, CP15 TEMPUS 3 & 4 & 7 MANUFACTURER LANDIS &GYR MODEL RWB2, RWB2.9, RWB 102 RWB200, RWB252, RWB20, RWB40 MINIMINDER MASTERMIND SELECT 207

DANFOSS RANDALL DRAYTON

POTTERTON GLOW-WORM SUNVIC
Otherwise fit new wall-plate supplied, and refer to wiring interchange guide below.

WIRING INTERCHANGE GUIDE

When replacing any of the below with your Sunvic SELECT 207XL programmer, fit new wall-plate supplied and follow the connection details shown. Whilst every effort is made to ensure accuracy of the instructions given, you will appreciate that discrepancies may occur, due to various reasons outside of our control.

Sunvic

SELECT 207XL SP100 & SP50 SP2 N N N N N N N N N 7 N N 5 1&7 1&7 N 3&3 4&N N N N N N N N N L L L L L L L L L 6 L L 6 L 7 1&3&L L L L L L L L L

Terminals

8 hw off ch off hw on HW HW ON 10 ch on CH CH On
Satchwell Satchwell Honeywell
Libra & DHP2201 ET1401 & ET1451 ST699B & C ST499A ST6300 & ST6400 ST7100

MP FP 2000

Randall
922 & & 3020P 3033 SET2 & SET5 TSR3+3 MK11 R6 TSR2P

Sangamo

410F1 & F9 & F414 M5

Potterton Horstmann

EP2000 & EP3000 Amethyst 7 & 10 Coral Diadem Diamond Gem Leucite

Smiths Switchmaster

Centroller 400 & & 900 & 9000

Thorn Towerchron

Microtimer T2002 T2000 & T2003

HW OFF CH OFF