BUQb_VF_\d]UdUb <YWXdC_S[Udc

BEGIN HERE

_b DUb]Y^Q\c
CAUTION: Read these instructions thoroughly before making installation. Do not deviate from assembly or wiring instructions. Always disconnect battery ground before making any electrical connections. If in doubt, please contact your dealer or VDO Instruments at (540) 665-2428.
IMPORTANT: Mounting dimensions vary for different gauges. Please be certain to follow the instructions for your specific gauge as described below.
2. Cut a 2 " (52 mm) diameter hole for all gauges except Pro Cockpit, which requires a 2 " (66 mm) hole. If the gauge is too snug, use a file to slightly enlarge the opening. (Diagram A) 3. Insert the instrument and secure it with either the VDO Spin-Lok clamp or mounting bracket. The Spin-Lok clamp can be reversed to accommodate various panel thicknesses. (Diagram B) DO NOT OVERTIGHTEN.

Wiring the Voltmeter:

1. Run wires from the instrument location through the firewall to: a) a positive (+), switched power source (i.e: after the fuse box and the ignition switch, or any other switch.

[text continues at # ]

<Q]` C_S[Ud

Voltmeter Installation:

1. Select the location where you will mount the gauge, and mark a center point.

<YWXd CgYdSX 6ecU 2_h

F_\d]UdUb DUb]Y^Q\c

CAUTION!!!

Parts List

Item Description

1. 2. 3. 4. 5. Voltmeter (2 " [52 mm] diameter) Voltmeter (2 " [66 mm] diameter) Lamp Socket Light Bulb (12-volt) VDO Spin-Lok Clamp or VDO Mounting Bracket and nuts Installation Instructions
These instructions contain information about gauges of different sizes. You must determine the size of your gauge before cutting any holes!

Quantity

1 or 1

2QddUbi

7b_e^T
Tools and Materials Needed For Installation: 16 Gauge stranded, insulated wire Non-insulated " spade connectors 2 " hole saw or 2 " hole saw Drill and drill bit set Half-round file Tape measure or ruler Small tools: wrench or nut driver, utility knife, pliers, etc.
Proper wiring of the VDO Voltmeter

Diagram C

VDO Limited Warranty
VDO North America warrants all merchandise against defects in factory workmanship and materials for a period of 24 months after purchase. This warranty applies to the first retail purchaser and covers only those products exposed to normal use or service. Provisions of this warranty shall not apply to a VDO product used for a purpose for which it is not designed, or which has been altered in any way that would be detrimental to the performance or life of the product, or misapplication, misuse, negligence or accident. On any part or product found to be defective after examination by VDO North America, VDO North America will only repair or replace the merchandise through the original selling dealer or on a direct basis. VDO North America assumes no responsibility for diagnosis, removal and/or installation labor, loss of vehicle use, loss of time, inconvenience or any other consequential expenses. The warranties herin are in lieu of any other expressed or implied warranties, including any implied warranty of merchantability or fitness, and any other obligation on the part of VDO North America, or selling dealer. (NOTE: This is a Limited Warranty as defined by the Magnuson-Moss Warranty Act of 1975.)

l North America

Installation Instructions
Instruction Sheet #Rev. 03/00
INSTRUCTIONS FOR THE INSTALLATION OF THE VOLTMETER ARE CONTAINED HEREIN. USE IS RESTRICTED TO 12 or 24-VOLT NEGATIVE GROUND ELECTRICAL SYSTEMS.

Voltmeter

VDO North America. 188 Brooke Rd. P.O. Box 2897. Winchester, VA 22603. Phone: 540-665-2428

To Begin, go to #

Dimension A
Dimension B 2.77" (70 mm)

CONTINUE HERE

This positive power source MUST BE SWITCHED, and must be protected with a fuse);
Pro-Cockpit: 2 " (66 mm)
All other: 2 " (52 mm) 2.19" (55.6 mm)

Table 1

'LPHQVLRQ $

'LPHQVLRQ %

and ground (negative []) wires to the terminals on the Voltmeters lamp socket. Be sure that the ground wire from the lamp socket uses its own ground connection (separate from the one used by the gauge terminal ground), as shown in Diagram C. At this point, the installation and wiring of the your new VDO Voltmeter is complete. Turn on the ignition and the lights in the car and check to see that the imstrument and light are working properly. If they arent, re-check your wiring, referring to the wiring description in Diagram C.
b) the light switch (also after the fuse in the fuse box); and c) a good ground location. 2. Connect the positive (+) and negative [ground] () wires as shown in Diagram C. 3. Connect the appropriate positive (+)

PD[ PP

Pro-Cockpit, Industrial and Series 1 Gauges
((""#]] !'& $$']]

!' $#]]

Mounting Nut direction depends on panel width 0 .4" (mm).4" .8" (mm)

4Y]U^cY_^1

"=$

4Y]U^cY_^2

DO NOT OVERTIGHTEN!
VDOs Spin-Lok Mounting Clamp

VDO Mounting Bracket

Gauge dimensions

Diagram A

Mounting using VDO Mounting Bracket or VDO Spin-Lok Clamp

Diagram B

Product Information

www.vdo.com

Viewline Voltmeter
Description Indication of Battery power
Features _ Integrated Warning LED. _ Changeable Frontbezels. _ LED Illumination _ Flush mount possibility _ High reliability

Picture: Voltmeter

Concept Housing Bezel Lens Dial Pointer Illumination Warning LED Mounting Connection
PC; flame retarding (UL94) PC or ABS; several colors and shapes (see table) PMMA; double lens backlit; different colors (see table) backlit, white on black dials; red on white dials Dial: LED amber (605nm) Pointer: LED red (632nm) red (632nm) spinlock Nut; locking height 0,5mm 20mm, optional Studs and Bracket; locking height 2 15mm 8 pin MQS connector system
VDO A trademark of the Continental Corporation
Technical Data Installation depth Installation diameter Deflection angle Operating Voltage Accuracy Current consumption Operating temperature Storage temperature
50mm 52mm 16 Volt, (18-32V) < 3,6 angular degrees < 140 mA, including Warning LED -30C to +80C; plated bezels (chrome) -30C to +70C -40C to +80C for 48h; plated bezels (chrome) -40C to +70C +90C for 1h Range Transformation time Retention time Range Rel. Humidity DIN_EN 61000-6-3 DIN_EN 61000-6-1 DIN_EN 61000-6-4 DIN_EN 61000-6-2 EN 60945 GL, Category C, F (under preparation) Sinus 2g; 10-500Hz; duration 16h Noise 3g; 10-1000Hz, duration 8h continuous Single shock Free fall 25g; 6ms; 1Hz 100g; 11ms 1m; 3 times -40C to +85C; plated bezels (chrome) -40C to +70C 10 seconds 2h +25C to +55C 95%

Temperature shock

Climatic test

EMC in conformity with

Standards

Vibration

Mechanical shock
Chemical resistance against - preservative agent - preservative agent remover - cold cleaner - methylated spirit - interior cleaner - drinks containing caffeine and tannin Nominal position Protection class NL 0 to NL 85 (DIN16257) according to IEC 60529 Front: IP67 (in Nominal position) Rear: IP52 (in Nominal position)
Reverse polarity protection yes, 5 minute Over voltage protection yes, 24V for1 minute (12V Gauges)
Technische nderungen vorbehalten
Technical details subject to change
The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All right reserved in the event of the grant of a patent, utility model or design.
available Gauges: No. packed A2C60100076 A2C60100077 A2C60100078 A2C60100079 A2C60100176 A2C60100177 A2C60100178 A2C60100179 No. unpacked A2C53191475 A2C53191478 A2C53191767 A2C53191769 A2C53191474 A2C53191476 A2C53191766 A2C53191768 colour black white black white black white black white Double Scale no no no no no no no no Measurement range 18 - 32V 18 - 32V 18 - 32V 18 - 32V 8 - 16V 8 - 16V 8 - 16V 8 - 16V ISO Symbol Voltage 24V 24V 24V 24V 12V 12V 12V 12V Double lens no no yes yes no no yes yes
Accessories: A2C59510854 A2C59510864 A2C53215640 A2C59510847 A2C53324664 Tyco No. 539635-1 Tyco No. 539682-2 Tyco No. 1355718-1 Tyco No. 963729-1 Tyco No. 1355717-1 Tyco No. 928999-1 Tyco No. 963715-1 VL Mounting Kit (studs and brackets) 52, 85, 110mm VL Mounting bracket flush mount VL Sealing Ring 52mm flush mount Bush housing, 8-pin Protective connector cap, 8-pin Hand pliers Tool for hand pliers. Single contacts 0.14 0.22 mm tin plated Single contacts 0.5 0.75 mm tin plated Strip 0.14 0.22 mm tin plated Strip 0.25 0.5 mm tin plated Strip 0.5 0.75 mm tin plated
Bezels 52mm black flat round triangle A2C53186040 A2C53186027 A2C53186024 black nickel* A2C53293468 A2C53293494 A2C53293545 brush aluminum* A2C53293480 A2C53293495 A2C53293546 chrome A2C53186023 A2C53186029 A2C53186026 gold* A2C53293482 A2C53293496 A2C53293548 white A2C53186022 A2C53186028 A2C53186025
* Only on request, no part off standard portfolio